Currently this driver uses a spinlock in the 8254 subdevice (*insn_read), (*insn_write),
and (*insn_config) functions. The comedi core checks if the subdevice is 'busy', in
parse_insn(), before any of the subdevice functions are attempted.

Remove the unnecessary spinlock.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 'counter_number' in these functions is the comedi channel number from the
chanspec. The comedi core validates the chanspec before calling the driver
functions. Remove the unnecessary checks.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This member is only used in the "set gate" and "set clock" helper functions. Remove
it and calculate the value when needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This member is only used one place in the driver. Remove it and calculate the
register offset when needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This member is only used one place in the driver. Remove it and calculate the
register offset when needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace the DIO200_[XYZ]GAT_SEL defines with a macro that returns the
correct register offset.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace the DIO200_[XYZ]CLK_SEL defines with a macro that returns the
correct register offset.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data conversion. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data conversion. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The hardware supported by this driver does not have an 8254 timer. Remove the
unnecessary include of "8253.h".
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some of the hardware supported by this driver include an 8254 timer. For
aesthetics, convert it to use the comedi_8254 module to provide support for
the 8254 timer.

This also fixes the (*insn_read) and (*insn_write) to work like the comedi
API expects. Currently they only read or write a single value.

It also fixes the (*insn_config). Currently the driver is attempting to
handle the configuration instructions GPCT_RESET and GPCT_SET_OPERATION.
These are just arbitrary valuse and are not real comedi configuration_ids.
They actually coorespond to:

  GPCT_RESET -> INSN_CONFIG_DIO_OUTPUT
  GPCT_SET_OPERATION -> INSN_CONFIG_ANALOG_TRIG

The number of parameters for the instructions is validated by the comedi
core in check_insn_config_length(). GPCT_RESET happens to work (insn->n == 1)
but GPCT_SET_OPERATION would fail. The INSN_CONFIG_ANALOG_TRIG expects
insn->n == 5 but GPCT_SET_OPERATION in this driver expects insn->n == 2.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some of the hardware supported by this driver includes an 8254 timer. For
aesthetics, convert it to use the comedi_8254 module to provide support for
the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The boardinfo for the 8254 timer is overly complex. The 8254 timer always has
3 channels and the 'regs' and 'specflags' members of diosubd_data are not
used. The only necessary information is the base 'addr' offset to the 8254
registers.

Replace the 's8254' member with an unsigned long 'timer_regbase'. Use that
to determine if the board has an 8254 timer during the attach of the driver.
Save the 'timer_regbase' in the subdevice 'private' pointer to use in the
subdevice functions.

For aesthetics, absorb pci_dio_add_8254() into the driver attach function.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Only two of the boards supported by this driver have an 8254 counter/timer.
Both of these boards have a single 8254 device. Currently the counter
subdevice functions are coded to support multiple 8254 devices. This is
unnecessary and just complicates the code.

Simplfy the subdevice functions to work for a single 8254 counter/timer and
refactor the driver (*attach) accordingly.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data conversion. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.

Tidy up the (*do_cmdtest) validation of the timer arguments.

Absorb the converted das1800_setup_counters() code into the (*do_cmd).
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data conversion. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.

Remove the unnecessary programming of timer 0. The private data 'count'
value is never set by the driver and the timer is reset to MODE0 when
the timers are initialized during the attach of the driver.

Remove the unnecessart convert_src check in the (*do_cmdtest). The only
valid convert_src is TRIG_TIMER.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The hardware supported by this driver includes an 8254 timer. For aesthetics,
convert it to use the comedi_8254 module to provide support for the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The hardware supported by this driver includes an 8254 timer. This timer is
not currently used, other than setting counters 1 and 2 to MODE4 to ensure
that the outputs are high.

For aesthetics, convert it to use the comedi_8254 module to provide support
for the 8254 timer. This will make it easier to add features later.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some of the hardware supported by this driver include an 8254 timer that is
exposed to the user as a comedi_subdevice. Convert it to use the comedi_8254
module to provide support for the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data conversion. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data acquisition. It also provides a comedi_subdevice to allow the user
to use channel 0 of the 8254 timer. Currently the subdevice support does not
work correctly due to and (*insn_config) that does not follow the comedi API.

Convert it to use the comedi_8254 module to provide support for the 8254 timer
and proper support for the subdevice.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The hardware supported by this drive has an 8254 timer. Currently this driver
does not use the timer functions.

For aesthetics, use the comedi_8254 module to provide support for the 8254
timer. This will ensure that the counters are all reset and make it easier
to add functionality later.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses two 8254 timers. One to generate the analog input pacer clock and
one to count the number of samples. Convert it to use the comedi_8254 module to
provide support for the 8254 timers.

Use the comedi_device 'pacer' member for the 8254 timer used for analog input. This
data is freed automatically by the core during the detach of the driver.

Store the data for the 8254 timer used to count samples in the private data. This
data needs to be freed by the driver when it is detached.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data acquisition. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses two 8254 timers to generate the pacer clocks. One for analog
input acquisition and one for analog output data conversion. Convert it to use
the comedi_8254 module to provide support for the 8254 timers.

Use the comedi_device 'pacer' member for the 8254 timer used for analog input.
This data is freed automatically by the core during the detach of the driver.

Store the data for the 8254 timer used for analog output in the private data.
This data needs to be freed by the driver when it is detached.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
output data conversion. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data acquisition. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data acquisition. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data acquisition. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.

Note that the pacer does not have to be stopped when starting a new async
command in pcl818_ai_cmd() or when the card is initialy reset by pcl818_reset().
The counters are all reset when the driver is initially attached and the
counters used by the pacer are stopped when a command is canceled.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data conversion. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver uses an 8254 timer to generate the pacer clock used for analog
input data acquisition. Convert it to use the comedi_8254 module to provide
support for the 8254 timer.

Note that the pacer does not have to be stopped when starting a new async
command in pcl812_ai_cmd() or when the card is initialy reset by pcl812_reset().
The counters are all reset when the driver is initially attached and the
counters used by the pacer are stopped when a command is canceled.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a new member to the comedi_device struct for a comedi_8254 'pacer'. This
provides a convient place to store the data allocated by the comedi_8254 module
for boards that use an 8254 device to create the data acquisition pacer clock.

Automatically free this pointer in comedi_device_detach_cleanup() so that the
drivers don't need to do it when then are detached.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A 8254 timer/counter is commonly used on data acquisition boards to provide
the internal pacer clock used to acquire analog input samples. Some boards
also to allow the timers to be used externally.

Currently the 8254 timers are supported by comedi using the 8253.h header
and a number of inline functions. This works for the internal pacer clock
but requires the drivers to implement subdevice code necessary to use the
timers externally.

Introduce a new module to support both the internal pacer clock and the
external counter subdevice. This will allow removing a bunch of duplicated
code in the drivers and standardizes the comedi 8254 timer support.

This implementation is based on the 8253.h inline functions and the various
subdevice functionality in the comedi drivers.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The read/write of the PLX_INTRCS_REG during the driver detach is not
necessary. The rtd_reset() function writes 0 to this register which
will disable all interrupts.

This also fixes a dereference after null check reported by coverity.

Reported-by: coverity (CID 751066)
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The {min,max}_scan_divisor values could overflow due to the
unsigned int * insigned int calculation. Change the type of the
local variable 'convert_divisor' to unsigned long long to avoid
the possible overflow.

Reported-by: coverity (CID 200653)
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The quick exit check of (mode == MODE_SINGLE_CHAN) results in coverity
reporting a logically dead code issue in the switch code in
labpc_ai_check_chanlist().

Remove the quick exit check and allow the function to handle the
MODE_SINGLE_CHAN normally (the for loop will only happen 1 time and
the function will return 0).

Reported-by: coverity (CID 1222108)
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

    This patch fixes checkpatch.pl warning.
    WARNING: else is not generally useful after a break or return
Signed-off-by: Alberto Pires de Oliveira Neto <mrpenguin2005@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

C99 says that a precision which is simply '.' with no following digits
or * should be interpreted as 0, which means that these format strings
actually mean 'print 16 spaces'. However, the kernel's printf
implementation treats this case as if the precision was omitted. Don't
rely on that quirk.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix checkpatch.ph errors "space prohibited between function name and
open parenthesis" in socklnd.h
Signed-off-by: Adrien Descamps <adrien.descamps@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

>From the indenting, it looks like curly braces were intended here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>