- 06 Jan, 2020 12 commits
-
-
Eran Ben Elisha authored
In case a reporter exists, error message is logged only to the devlink tracer. The devlink tracer is a visibility utility only, which user can choose not to monitor. After cited patch, 3rd party monitoring tools that tracks these error message will no longer find them in dmesg, causing a regression. With this patch, error messages are also logged into the dmesg. Fixes: c50de4af ("net/mlx5e: Generalize tx reporter's functionality") Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Dmytro Linkin authored
Following scenario easily break driver logic and crash the kernel: 1. Add rule with mirred actions to same device. 2. Delete this rule. In described scenario rule is not added to database and on deletion driver access invalid entry. Example: $ tc filter add dev ens1f0_0 ingress protocol ip prio 1 \ flower skip_sw \ action mirred egress mirror dev ens1f0_1 pipe \ action mirred egress redirect dev ens1f0_1 $ tc filter del dev ens1f0_0 ingress protocol ip prio 1 Dmesg output: [ 376.634396] mlx5_core 0000:82:00.0: mlx5_cmd_check:756:(pid 3439): DESTROY_FLOW_GROUP(0x934) op_mod(0x0) failed, status bad resource state(0x9), syndrome (0x563e2f) [ 376.654983] mlx5_core 0000:82:00.0: del_hw_flow_group:567:(pid 3439): flow steering can't destroy fg 89 of ft 3145728 [ 376.673433] kasan: CONFIG_KASAN_INLINE enabled [ 376.683769] kasan: GPF could be caused by NULL-ptr deref or user memory access [ 376.695229] general protection fault: 0000 [#1] PREEMPT SMP KASAN PTI [ 376.705069] CPU: 7 PID: 3439 Comm: tc Not tainted 5.4.0-rc5+ #76 [ 376.714959] Hardware name: Supermicro SYS-2028TP-DECTR/X10DRT-PT, BIOS 2.0a 08/12/2016 [ 376.726371] RIP: 0010:mlx5_del_flow_rules+0x105/0x960 [mlx5_core] [ 376.735817] Code: 01 00 00 00 48 83 eb 08 e8 28 d9 ff ff 4c 39 e3 75 d8 4c 8d bd c0 02 00 00 48 b8 00 00 00 00 00 fc ff df 4c 89 fa 48 c1 ea 03 <0f> b6 04 02 84 c0 74 08 3c 03 0f 8e 84 04 00 00 48 8d 7d 28 8b 9 d [ 376.761261] RSP: 0018:ffff888847c56db8 EFLAGS: 00010202 [ 376.770054] RAX: dffffc0000000000 RBX: ffff8888582a6da0 RCX: ffff888847c56d60 [ 376.780743] RDX: 0000000000000058 RSI: 0000000000000008 RDI: 0000000000000282 [ 376.791328] RBP: 0000000000000000 R08: fffffbfff0c60ea6 R09: fffffbfff0c60ea6 [ 376.802050] R10: fffffbfff0c60ea5 R11: ffffffff8630752f R12: ffff8888582a6da0 [ 376.812798] R13: dffffc0000000000 R14: ffff8888582a6da0 R15: 00000000000002c0 [ 376.823445] FS: 00007f675f9a8840(0000) GS:ffff88886d200000(0000) knlGS:0000000000000000 [ 376.834971] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 376.844179] CR2: 00000000007d9640 CR3: 00000007d3f26003 CR4: 00000000001606e0 [ 376.854843] Call Trace: [ 376.868542] __mlx5_eswitch_del_rule+0x49/0x300 [mlx5_core] [ 376.877735] mlx5e_tc_del_fdb_flow+0x6ec/0x9e0 [mlx5_core] [ 376.921549] mlx5e_flow_put+0x2b/0x50 [mlx5_core] [ 376.929813] mlx5e_delete_flower+0x5b6/0xbd0 [mlx5_core] [ 376.973030] tc_setup_cb_reoffload+0x29/0xc0 [ 376.980619] fl_reoffload+0x50a/0x770 [cls_flower] [ 377.015087] tcf_block_playback_offloads+0xbd/0x250 [ 377.033400] tcf_block_setup+0x1b2/0xc60 [ 377.057247] tcf_block_offload_cmd+0x195/0x240 [ 377.098826] tcf_block_offload_unbind+0xe7/0x180 [ 377.107056] __tcf_block_put+0xe5/0x400 [ 377.114528] ingress_destroy+0x3d/0x60 [sch_ingress] [ 377.122894] qdisc_destroy+0xf1/0x5a0 [ 377.129993] qdisc_graft+0xa3d/0xe50 [ 377.151227] tc_get_qdisc+0x48e/0xa20 [ 377.165167] rtnetlink_rcv_msg+0x35d/0x8d0 [ 377.199528] netlink_rcv_skb+0x11e/0x340 [ 377.219638] netlink_unicast+0x408/0x5b0 [ 377.239913] netlink_sendmsg+0x71b/0xb30 [ 377.267505] sock_sendmsg+0xb1/0xf0 [ 377.273801] ___sys_sendmsg+0x635/0x900 [ 377.312784] __sys_sendmsg+0xd3/0x170 [ 377.338693] do_syscall_64+0x95/0x460 [ 377.344833] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 377.352321] RIP: 0033:0x7f675e58e090 To avoid this, for every mirred action check if output device was already processed. If so - drop rule with EOPNOTSUPP error. Signed-off-by:Dmytro Linkin <dmitrolin@mellanox.com> Reviewed-by:
Roi Dayan <roid@mellanox.com> Reviewed-by:
Vlad Buslov <vladbu@mellanox.com> Signed-off-by:
-
David S. Miller authored
Igor Russkikh says: ==================== Aquantia/Marvell atlantic bugfixes 2020/01 Here is a set of recently discovered bugfixes, ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Igor Russkikh authored
Function entries were duplicated accidentally, removing the dups. Fixes: ea4b4d7f ("net: atlantic: loopback tests via private flags") Signed-off-by:
Igor Russkikh <irusskikh@marvell.com> Signed-off-by:
-
Igor Russkikh authored
Initial loopback configuration should be called earlier, before starting traffic on HW blocks. Otherwise depending on race conditions it could be kept disabled. Fixes: ea4b4d7f ("net: atlantic: loopback tests via private flags") Signed-off-by:
-
Igor Russkikh authored
Last code/checkpatch cleanup did a copy paste error where code from firmware 3 API logic was moved to firmware 1 logic. This resulted in FW1.x users would never see the link state as active. Fixes: 7b0c342f ("net: atlantic: code style cleanup") Signed-off-by:
-
Vikas Gupta authored
Fix calling multiple tee_client_close_context in case of shm allocation fails. Fixes: 24688095 (“firmware: broadcom: add OP-TEE based BNXT f/w manager”) Signed-off-by:
Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by:
-
Andrew Lunn authored
The 6390 family uses an extended register to set the port connected to the CPU. The lower 5 bits indicate the port, the upper three bits are the priority of the frames as they pass through the switch, what egress queue they should use, etc. Since frames being set to the CPU are typically management frames, BPDU, IGMP, ARP, etc set the priority to 7, the reset default, and the highest. Fixes: 33641994 ("net: dsa: mv88e6xxx: Monitor and Management tables") Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Tested-by:
Chris Healy <cphealy@gmail.com> Signed-off-by:
-
Krzysztof Kozlowski authored
Fix up inconsistent usage of upper and lowercase letters in "Samsung" name. "SAMSUNG" is not an abbreviation but a regular trademarked name. Therefore it should be written with lowercase letters starting with capital letter. Although advertisement materials usually use uppercase "SAMSUNG", the lowercase version is used in all legal aspects (e.g. on Wikipedia and in privacy/legal statements on https://www.samsung.com/semiconductor/privacy-global/). Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
-
Krzysztof Kozlowski authored
Since net_device.mem_start is unsigned long, it should not be cast to int right before casting to pointer. This fixes warning (compile testing on alpha architecture): drivers/net/wan/sdla.c: In function ‘sdla_transmit’: drivers/net/wan/sdla.c:711:13: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast] Signed-off-by: -
Xin Long authored
This patch is to fix a memleak caused by no place to free cmd->obj.chunk for the unprocessed SCTP_CMD_REPLY. This issue occurs when failing to process a cmd while there're still SCTP_CMD_REPLY cmds on the cmd seq with an allocated chunk in cmd->obj.chunk. So fix it by freeing cmd->obj.chunk for each SCTP_CMD_REPLY cmd left on the cmd seq when any cmd returns error. While at it, also remove 'nomem' label. Reported-by: syzbot+107c4aff5f392bf1517f@syzkaller.appspotmail.com Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Ying Xue authored
syzbot found the following crash on: ===================================================== BUG: KMSAN: uninit-value in __nlmsg_parse include/net/netlink.h:661 [inline] BUG: KMSAN: uninit-value in nlmsg_parse_deprecated include/net/netlink.h:706 [inline] BUG: KMSAN: uninit-value in __tipc_nl_compat_dumpit+0x553/0x11e0 net/tipc/netlink_compat.c:215 CPU: 0 PID: 12425 Comm: syz-executor062 Not tainted 5.5.0-rc1-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x220 lib/dump_stack.c:118 kmsan_report+0x128/0x220 mm/kmsan/kmsan_report.c:108 __msan_warning+0x57/0xa0 mm/kmsan/kmsan_instr.c:245 __nlmsg_parse include/net/netlink.h:661 [inline] nlmsg_parse_deprecated include/net/netlink.h:706 [inline] __tipc_nl_compat_dumpit+0x553/0x11e0 net/tipc/netlink_compat.c:215 tipc_nl_compat_dumpit+0x761/0x910 net/tipc/netlink_compat.c:308 tipc_nl_compat_handle net/tipc/netlink_compat.c:1252 [inline] tipc_nl_compat_recv+0x12e9/0x2870 net/tipc/netlink_compat.c:1311 genl_family_rcv_msg_doit net/netlink/genetlink.c:672 [inline] genl_family_rcv_msg net/netlink/genetlink.c:717 [inline] genl_rcv_msg+0x1dd0/0x23a0 net/netlink/genetlink.c:734 netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477 genl_rcv+0x63/0x80 net/netlink/genetlink.c:745 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xfa0/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x11f0/0x1480 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x1362/0x13f0 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x4f0/0x5e0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:295 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x444179 Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 1b d8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffd2d6409c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004002e0 RCX: 0000000000444179 RDX: 0000000000000000 RSI: 0000000020000140 RDI: 0000000000000003 RBP: 00000000006ce018 R08: 0000000000000000 R09: 00000000004002e0 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000401e20 R13: 0000000000401eb0 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:149 [inline] kmsan_internal_poison_shadow+0x5c/0x110 mm/kmsan/kmsan.c:132 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:86 slab_alloc_node mm/slub.c:2774 [inline] __kmalloc_node_track_caller+0xe47/0x11f0 mm/slub.c:4382 __kmalloc_reserve net/core/skbuff.c:141 [inline] __alloc_skb+0x309/0xa50 net/core/skbuff.c:209 alloc_skb include/linux/skbuff.h:1049 [inline] nlmsg_new include/net/netlink.h:888 [inline] tipc_nl_compat_dumpit+0x6e4/0x910 net/tipc/netlink_compat.c:301 tipc_nl_compat_handle net/tipc/netlink_compat.c:1252 [inline] tipc_nl_compat_recv+0x12e9/0x2870 net/tipc/netlink_compat.c:1311 genl_family_rcv_msg_doit net/netlink/genetlink.c:672 [inline] genl_family_rcv_msg net/netlink/genetlink.c:717 [inline] genl_rcv_msg+0x1dd0/0x23a0 net/netlink/genetlink.c:734 netlink_rcv_skb+0x431/0x620 net/netlink/af_netlink.c:2477 genl_rcv+0x63/0x80 net/netlink/genetlink.c:745 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline] netlink_unicast+0xfa0/0x1100 net/netlink/af_netlink.c:1328 netlink_sendmsg+0x11f0/0x1480 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:639 [inline] sock_sendmsg net/socket.c:659 [inline] ____sys_sendmsg+0x1362/0x13f0 net/socket.c:2330 ___sys_sendmsg net/socket.c:2384 [inline] __sys_sendmsg+0x4f0/0x5e0 net/socket.c:2417 __do_sys_sendmsg net/socket.c:2426 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2424 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2424 do_syscall_64+0xb6/0x160 arch/x86/entry/common.c:295 entry_SYSCALL_64_after_hwframe+0x44/0xa9 ===================================================== The complaint above occurred because the memory region pointed by attrbuf variable was not initialized. To eliminate this warning, we use kcalloc() rather than kmalloc_array() to allocate memory for attrbuf. Reported-by: syzbot+b1fd2bf2c89d8407e15f@syzkaller.appspotmail.com Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
-
- 05 Jan, 2020 4 commits
-
-
Stephen Boyd authored
The only clk init function in this driver that register a clk is fu540_c000_clk_init(), and thus we need to unregister the clk when this driver is removed on that platform. Other init functions, for example macb_clk_init(), don't register clks and therefore we shouldn't unregister the clks when this driver is removed. Convert this registration path to devm so it gets auto-unregistered when this driver is removed and drop the clk_unregister() calls in driver remove (and error paths) so that we don't erroneously remove a clk from the system that isn't registered by this driver. Otherwise we get strange crashes with a use-after-free when the devm_clk_get() call in macb_clk_init() calls clk_put() on a clk pointer that has become invalid because it is freed in clk_unregister(). Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Yash Shah <yash.shah@sifive.com> Reported-by:
Guenter Roeck <linux@roeck-us.net> Fixes: c218ad55 ("macb: Add support for SiFive FU540-C000") Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Krzysztof Kozlowski authored
The emails to ks.giri@samsung.com and vipul.pandya@samsung.com bounce with 550 error code: host mailin.samsung.com[203.254.224.12] said: 550 5.1.1 Recipient address rejected: User unknown (in reply to RCPT TO command)" Drop Girish K S and Vipul Pandya from sxgbe maintainers entry. Cc: Byungho An <bh74.an@samsung.com> Signed-off-by: -
Carl Huang authored
The len used for skb_put_padto is wrong, it need to add len of hdr. In qrtr_node_enqueue, local variable size_t len is assign with skb->len, then skb_push(skb, sizeof(*hdr)) will add skb->len with sizeof(*hdr), so local variable size_t len is not same with skb->len after skb_push(skb, sizeof(*hdr)). Then the purpose of skb_put_padto(skb, ALIGN(len, 4)) is to add add pad to the end of the skb's data if skb->len is not aligned to 4, but unfortunately it use len instead of skb->len, at this line, skb->len is 32 bytes(sizeof(*hdr)) more than len, for example, len is 3 bytes, then skb->len is 35 bytes(3 + 32), and ALIGN(len, 4) is 4 bytes, so __skb_put_padto will do nothing after check size(35) < len(4), the correct value should be 36(sizeof(*hdr) + ALIGN(len, 4) = 32 + 4), then __skb_put_padto will pass check size(35) < len(36) and add 1 byte to the end of skb's data, then logic is correct. function of skb_push: void *skb_push(struct sk_buff *skb, unsigned int len) { skb->data -= len; skb->len += len; if (unlikely(skb->data < skb->head)) skb_under_panic(skb, len, __builtin_return_address(0)); return skb->data; } function of skb_put_padto static inline int skb_put_padto(struct sk_buff *skb, unsigned int len) { return __skb_put_padto(skb, len, true); } function of __skb_put_padto static inline int __skb_put_padto(struct sk_buff *skb, unsigned int len, bool free_on_error) { unsigned int size = skb->len; if (unlikely(size < len)) { len -= size; if (__skb_pad(skb, len, free_on_error)) return -ENOMEM; __skb_put(skb, len); } return 0; } Signed-off-by:Carl Huang <cjhuang@codeaurora.org> Signed-off-by:
Wen Gong <wgong@codeaurora.org> Signed-off-by:
-
Fenghua Yu authored
Atomic operations that span cache lines are super-expensive on x86 (not just to the current processor, but also to other processes as all memory operations are blocked until the operation completes). Upcoming x86 processors have a switch to cause such operations to generate a #AC trap. It is expected that some real time systems will enable this mode in BIOS. In preparation for this, it is necessary to fix code that may execute atomic instructions with operands that cross cachelines because the #AC trap will crash the kernel. Since "pwol_mask" is local and never exposed to concurrency, there is no need to set bits in pwol_mask using atomic operations. Directly operate on the byte which contains the bit instead of using __set_bit() to avoid any big endian concern due to type cast to unsigned long in __set_bit(). Suggested-by:
Peter Zijlstra <peterz@infradead.org> Signed-off-by:
Fenghua Yu <fenghua.yu@intel.com> Signed-off-by:
Tony Luck <tony.luck@intel.com> Signed-off-by:
-
- 03 Jan, 2020 10 commits
-
-
Liran Alon authored
Current code use dma_wmb() to ensure Rx/Tx descriptors are visible to device before writing to doorbell. However, these dma_wmb() are wrong and unnecessary. Therefore, they should be removed. iowrite32be() called from gve_rx_write_doorbell()/gve_tx_put_doorbell() should guaratee that all previous writes to WB/UC memory is visible to device before the write done by iowrite32be(). E.g. On ARM64, iowrite32be() calls __iowmb() which expands to dma_wmb() and only then calls __raw_writel(). Reviewed-by:
Si-Wei Liu <si-wei.liu@oracle.com> Signed-off-by:
Liran Alon <liran.alon@oracle.com> Signed-off-by:
-
Russell King authored
The kernel test robot reports a boot failure with qemu in 5.5-rc, referencing commit 2203cbf2 ("net: sfp: move fwnode parsing into sfp-bus layer"). This is caused by phylink_create() being passed a NULL fwnode, causing fwnode_property_get_reference_args() to return -EINVAL. Don't attempt to attach to a SFP bus if we have no fwnode, which avoids this issue. Reported-by:
kernel test robot <rong.a.chen@intel.com> Fixes: 2203cbf2 ("net: sfp: move fwnode parsing into sfp-bus layer") Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
-
Jesper Dangaard Brouer authored
DaveM's git tree have been moved into a named subdir 'netdev' to deal with allowing Jakub Kicinski to help co-maintain the trees. Link: https://www.kernel.org/doc/html/latest/networking/netdev-FAQ.htmlSigned-off-by:
Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by:
-
Hangbin Liu authored
The loopback feature is only supported on a few drivers like broadcom, mellanox, etc. The default veth driver has not supported it yet. To avoid returning failed and making the runner feel confused, let's just skip the test on drivers that not support loopback. Fixes: ad113409 ("selftests: Add loopback test") Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
David S. Miller authored
Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-5.5-20200102' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2020-01-02 this is a pull request of 9 patches for net/master. The first 5 patches target all the tcan4x5x driver. The first 3 patches of them are by Dan Murphy and Sean Nyekjaer and improve the device initialization (power on, reset and get device out of standby before register access). The next patch is by Dan Murphy and disables the INH pin device-state if the GPIO is unavailable. The last patch for the tcan4x5x driver is by Gustavo A. R. Silva and fixes an inconsistent PTR_ERR check in the tcan4x5x_parse_config() function. The next patch is by Oliver Hartkopp and targets the generic CAN device infrastructure. It ensures that an initialized headroom in outgoing CAN sk_buffs (e.g. if injected by AF_PACKET). The last 2 patches are by Johan Hovold and fix the kvaser_usb and gs_usb drivers by always using the current alternate setting not blindly the first one. ==================== Signed-off-by:
-
Andrew Lunn authored
In order to dump the FECs registers the clocks have to be ticking, otherwise a data abort occurs. Add calls to runtime PM so they are enabled and later disabled. Fixes: e8fcfcd5 ("net: fec: optimize the clock management to save power") Reported-by:
Chris Healy <Chris.Healy@zii.aero> Signed-off-by:
-
Hangbin Liu authored
Before ip_tunnel_ecn_encap() and udp_tunnel_xmit_skb() we should filter tos value by RT_TOS() instead of using config tos directly. vxlan_get_route() would filter the tos to fl4.flowi4_tos but we didn't return it back, as geneve_get_v4_rt() did. So we have to use RT_TOS() directly in function ip_tunnel_ecn_encap(). Fixes: 206aaafc ("VXLAN: Use IP Tunnels tunnel ENC encap API") Fixes: 1400615d ("vxlan: allow setting ipv6 traffic class") Signed-off-by:
-
Wen Yang authored
The variables 'window_interval' is u64 and do_div() truncates it to 32 bits, which means it can test non-zero and be truncated to zero for division. The unit of window_interval is nanoseconds, so its lower 32-bit is relatively easy to exceed. Fix this issue by using div64_u64() instead. Fixes: 7298de9c ("sch_cake: Add ingress mode") Signed-off-by:
Wen Yang <wenyang@linux.alibaba.com> Cc: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Cc: Toke Høiland-Jørgensen <toke@redhat.com> Cc: David S. Miller <davem@davemloft.net> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: cake@lists.bufferbloat.net Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by:
-
David S. Miller authored
It can take on the values of '0', '1', and '2' and thus is not a boolean. Signed-off-by:
-
- 02 Jan, 2020 11 commits
-
-
Pengcheng Yang authored
When we receive a D-SACK, where the sequence number satisfies: undo_marker <= start_seq < end_seq <= prior_snd_una we consider this is a valid D-SACK and tcp_is_sackblock_valid() returns true, then this D-SACK is discarded as "old stuff", but the variable first_sack_index is not marked as negative in tcp_sacktag_write_queue(). If this D-SACK also carries a SACK that needs to be processed (for example, the previous SACK segment was lost), this SACK will be treated as a D-SACK in the following processing of tcp_sacktag_write_queue(), which will eventually lead to incorrect updates of undo_retrans and reordering. Fixes: fd6dad61 ("[TCP]: Earlier SACK block verification & simplify access to them") Signed-off-by:
Pengcheng Yang <yangpc@wangsu.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Baruch Siach authored
mv88e6xxx_port_set_cmode() relies on cmode stored in struct mv88e6xxx_port to skip cmode update when the requested value matches the cached value. It turns out that mv88e6xxx_port_hidden_write() might change the port cmode setting as a side effect, so we can't rely on the cached value to determine that cmode update in not necessary. Force cmode update in mv88e6341_port_set_cmode(), to make serdes configuration work again. Other mv88e6xxx_port_set_cmode() callers keep the current behaviour. This fixes serdes configuration of the 6141 switch on SolidRun Clearfog GT-8K. Fixes: 7a3007d2 ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family") Reported-by:
Denis Odintsov <d.odintsov@traviangames.com> Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Reviewed-by:
-
Florian Faber authored
Under load, the RX side of the mscan driver can get stuck while TX still works. Restarting the interface locks up the system. This behaviour could be reproduced reliably on a MPC5121e based system. The patch fixes the return value of the NAPI polling function (should be the number of processed packets, not constant 1) and the condition under which IRQs are enabled again after polling is finished. With this patch, no more lockups were observed over a test period of ten days. Fixes: afa17a50 ("net/can: add driver for mscan family & mpc52xx_mscan") Signed-off-by:
Florian Faber <faber@faberman.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Johan Hovold authored
Make sure to always use the descriptors of the current alternate setting to avoid future issues when accessing fields that may differ between settings. Signed-off-by:
Johan Hovold <johan@kernel.org> Fixes: d08e973a ("can: gs_usb: Added support for the GS_USB CAN devices") Signed-off-by:
-
Johan Hovold authored
Make sure to use the current alternate setting when verifying the interface descriptors to avoid binding to an invalid interface. Failing to do so could cause the driver to misbehave or trigger a WARN() in usb_submit_urb() that kernels with panic_on_warn set would choke on. Fixes: aec5fb22 ("can: kvaser_usb: Add support for Kvaser USB hydra family") Cc: stable <stable@vger.kernel.org> # 4.19 Cc: Jimmy Assarsson <extja@kvaser.com> Cc: Christer Beskow <chbe@kvaser.com> Cc: Nicklas Johansson <extnj@kvaser.com> Cc: Martin Henriksson <mh@kvaser.com> Signed-off-by:
-
Oliver Hartkopp authored
KMSAN sysbot detected a read access to an untinitialized value in the headroom of an outgoing CAN related sk_buff. When using CAN sockets this area is filled appropriately - but when using a packet socket this initialization is missing. The problematic read access occurs in the CAN receive path which can only be triggered when the sk_buff is sent through a (virtual) CAN interface. So we check in the sending path whether we need to perform the missing initializations. Fixes: d3b58c47 ("can: replace timestamp as unique skb attribute") Reported-by: syzbot+b02ff0707a97e4e79ebb@syzkaller.appspotmail.com Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Tested-by:
-
Gustavo A. R. Silva authored
Fix inconsistent IS_ERR and PTR_ERR in tcan4x5x_parse_config(). The proper pointer to be passed as argument is tcan4x5x->device_wake_gpio. This bug was detected with the help of Coccinelle. Fixes: 2de49735 ("can: tcan45x: Make wake-up GPIO an optional GPIO") Signed-off-by:
Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by:
Dan Murphy <dmurphy@ti.com> Signed-off-by:
-
Dan Murphy authored
If the device state GPIO is not connected to the host then disable the INH output from the TCAN device per section 8.3.5 of the data sheet. Signed-off-by:
-
Sean Nyekjaer authored
It's a good idea to reset a ip-block/spi device before using it, this patch will reset the device. And a generic reset function if needed elsewhere. Signed-off-by:
Sean Nyekjaer <sean@geanix.com> Signed-off-by:
-
Dan Murphy authored
The tcan4x5x_parse_config() function now performs action on the device either reading or writing and a reset. If the devive has a switchable power supppy (i.e. regulator is managed) it needs to be turned on. So turn on the regulator if available. If the parsing fails, turn off the regulator. Fixes: 2de49735 ("can: tcan45x: Make wake-up GPIO an optional GPIO") Signed-off-by:
-
Sean Nyekjaer authored
The m_can tries to detect if Non ISO Operation is available while in standby mode, this function results in the following error: | tcan4x5x spi2.0 (unnamed net_device) (uninitialized): Failed to init module | tcan4x5x spi2.0: m_can device registered (irq=84, version=32) | tcan4x5x spi2.0 can2: TCAN4X5X successfully initialized. When the tcan device comes out of reset it goes in standby mode. The m_can driver tries to access the control register but fails due to the device being in standby mode. So this patch will put the tcan device in normal mode before the m_can driver does the initialization. Fixes: 5443c226 ("can: tcan4x5x: Add tcan4x5x driver to the kernel") Cc: stable@vger.kernel.org Signed-off-by:
-
- 31 Dec, 2019 3 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann. 2) Fix port selection on big endian in nft_tproxy, from Phil Sutter. 3) Fix precision tracking for unbound scalars in bpf verifier, from Daniel Borkmann. 4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio Messina. 5) Do not perform a neigh confirmation during a pmtu update over a tunnel, from Hangbin Liu. 6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur. 7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean. 8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from Geert Uytterhoeven * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits) hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename() net/sched: add delete_empty() to filters and use it in cls_flower tcp: Fix highest_sack and highest_sack_seq ptp: fix the race between the release of ptp_clock and cdev net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation net: dsa: sja1105: Remove restriction of zero base-time for taprio offload net: dsa: sja1105: Really make the PTP command read-write net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot cxgb4/cxgb4vf: fix flow control display for auto negotiation mlxsw: spectrum: Use dedicated policer for VRRP packets mlxsw: spectrum_router: Skip loopback RIFs during MAC validation net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device net_sched: sch_fq: properly set sk->sk_pacing_status bnx2x: Fix accounting of vlan resources among the PFs bnx2x: Use appropriate define for vlan credit of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy net: phy: aquantia: add suspend / resume ops for AQR105 dpaa_eth: fix DMA mapping leak ... -
git://git.osdn.net/gitroot/tomoyo/tomoyo-test1Linus Torvalds authored
Pull tomoyo fixes from Tetsuo Handa: "Two bug fixes: - Suppress RCU warning at list_for_each_entry_rcu() - Don't use fancy names on sockets" * tag 'tomoyo-fixes-for-5.5' of git://git.osdn.net/gitroot/tomoyo/tomoyo-test1: tomoyo: Suppress RCU warning at list_for_each_entry_rcu(). tomoyo: Don't use nifty names on sockets.
-
Taehee Yoo authored
hsr slave interfaces don't have debugfs directory. So, hsr_debugfs_rename() shouldn't be called when hsr slave interface name is changed. Test commands: ip link add dummy0 type dummy ip link add dummy1 type dummy ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1 ip link set dummy0 name ap Splat looks like: [21071.899367][T22666] ap: renamed from dummy0 [21071.914005][T22666] ================================================================== [21071.919008][T22666] BUG: KASAN: slab-out-of-bounds in hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.923640][T22666] Read of size 8 at addr ffff88805febcd98 by task ip/22666 [21071.926941][T22666] [21071.927750][T22666] CPU: 0 PID: 22666 Comm: ip Not tainted 5.5.0-rc2+ #240 [21071.929919][T22666] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [21071.935094][T22666] Call Trace: [21071.935867][T22666] dump_stack+0x96/0xdb [21071.936687][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.937774][T22666] print_address_description.constprop.5+0x1be/0x360 [21071.939019][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.940081][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.940949][T22666] __kasan_report+0x12a/0x16f [21071.941758][T22666] ? hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.942674][T22666] kasan_report+0xe/0x20 [21071.943325][T22666] hsr_debugfs_rename+0xaa/0xb0 [hsr] [21071.944187][T22666] hsr_netdev_notify+0x1fe/0x9b0 [hsr] [21071.945052][T22666] ? __module_text_address+0x13/0x140 [21071.945897][T22666] notifier_call_chain+0x90/0x160 [21071.946743][T22666] dev_change_name+0x419/0x840 [21071.947496][T22666] ? __read_once_size_nocheck.constprop.6+0x10/0x10 [21071.948600][T22666] ? netdev_adjacent_rename_links+0x280/0x280 [21071.949577][T22666] ? __read_once_size_nocheck.constprop.6+0x10/0x10 [21071.950672][T22666] ? lock_downgrade+0x6e0/0x6e0 [21071.951345][T22666] ? do_setlink+0x811/0x2ef0 [21071.951991][T22666] do_setlink+0x811/0x2ef0 [21071.952613][T22666] ? is_bpf_text_address+0x81/0xe0 [ ... ] Reported-by: syzbot+9328206518f08318a5fd@syzkaller.appspotmail.com Fixes: 4c2d5e33 ("hsr: rename debugfs file when interface name is changed") Signed-off-by:Taehee Yoo <ap420073@gmail.com> Signed-off-by:
-
