- 17 Sep, 2006 13 commits
-
-
Stefan Richter authored
Conflicts: drivers/ieee1394/hosts.c Patch "lockdep: annotate ieee1394 skb-queue-head locking" was meddling with patch "ieee1394: fix kerneldoc of hpsb_alloc_host". Signed-off-by:Stefan Richter <stefanr@s5r6.in-berlin.de>
-
Jeff Garzik authored
-
Frank Pavlic authored
[PATCH 9/9] s390: qeth driver fixes [6/6] From: Frank Pavlic <fpavlic@de.ibm.com> - Hipersockets has no IPV6 support, thus prevent issueing SETRTG_IPV6 control commands on Hipersockets devices. - fixed error handling in qeth_sysfs_(un)register Signed-off-by:
Frank Pavlic <fpavlic@de.ibm.com> Signed-off-by:
Jeff Garzik <jeff@garzik.org>
-
Frank Pavlic authored
[PATCH 8/9] s390: qeth driver fixes [5/6] From: Frank Pavlic <fpavlic@de.ibm.com> fix kernel panic in qdio queue handling. qeth_qdio_clear_card() could be invoked by 2 CPUs simultaneously (for example reboot event and recovery). Signed-off-by:
-
Frank Pavlic authored
[PATCH 7/9] s390: qeth driver fixes [4/6] From: Frank Pavlic <fpavlic@de.ibm.com> - fix kernel crash due to race, set card->state to SOFTSETUP after card and card->dev are initialized properly. - remove CONFIG_QETH_PERF_STATS, use sysfs attribute instead, as we want to have the ability to turn on/off the statistics at runtime. Signed-off-by:
-
Frank Pavlic authored
[PATCH 6/9] s390: qeth driver fixes [3/6] From: Frank Pavlic <fpavlic@de.ibm.com> fixed kernel panic caused by qeth driver: Using a bonding device qeth driver will realloc headroom for every skb coming from the bond device. Once this happens qeth frees the original skb and set the skb pointer to the new realloced skb. Under heavy transmit workload (e.g.UDP streams) through bond network device the qdio output queue might get full. In this case we return with EBUSY from qeth_send_packet. Returning to qeth_hard_start_xmit routine the skb address on the stack still points to the old address, which has been freed before. Returning from qeth_hard_start_xmit with EBUSY results in requeuing the skb. In this case it corrupts the qdisc queue and results in kernel panic. Signed-off-by: -
Frank Pavlic authored
[PATCH 5/9] s390: qeth driver fixes [2/6] From: Frank Pavlic <fpavlic@de.ibm.com> - fixed error handling in create_device_attributes - fixed some minor bugs in IPv4 and IPv6 address checking Signed-off-by:
-
Frank Pavlic authored
[PATCH 4/9] s390: qeth driver fixes [1/6] From: Frank Pavlic <fpavlic@de.ibm.com> - Drop incoming packets with vlan_tag set if card->vlangrp is not set. - use always vlan_hwaccel_rx to pass vlan frames to the stack. - fix recovery problem. Device was recovered properly but still not working. netif_carrier_on call right before recovery start fixes it. Signed-off-by: -
Frank Pavlic authored
[PATCH 3/9] s390: Makefile cleanup From: Frank Pavlic <fpavlic@de.ibm.com> remove CONFIG_MPC from Makefile which was introduced accidently in the past. Signed-off-by:
-
Frank Pavlic authored
[PATCH 2/9] s390: netiucv driver fixes From: Frank Pavlic <fpavlic@de.ibm.com> - missing lock initialization added - avoid duplicate iucv-interfaces to the same peer - rw-lock added for manipulating the list of defined iucv connections Signed-off-by: -
Frank Pavlic authored
Hi Jeff, this is a RESEND of the nine s390 network driver patches. I finally found that my kmail corrupted almost every patch I sent the last time. Please apply these 9 patches and forget about my first attempt! Sorry for the delay, I had some fights with sendmail, IMAP and mutt configuration. Frank [RESEND PATCH 1/9] s390: minor s390 network driver fixes From: Frank Pavlic <fpavlic@de.ibm.com> - iucv driver: use do { } while (0) constructs instead of empty defines to avoid compile bugs. - ctc driver: missing lock initialization added - lcs driver: BUG_ON usage was removed accidently with the last lcs patch. Put them back in place. Signed-off-by: -
Benjamin LaHaise authored
Add the CPU identification needed by oprofile for Intel (r) Core (tm) 2 CPUs. Signed-off-by:
Benjamin LaHaise <benjamin.c.lahaise@intel.com> Signed-off-by:
Andi Kleen <ak@suse.de> Cc: "Arun Sharma" <aruns@google.com> Signed-off-by:
Andrew Morton <akpm@osdl.org> Signed-off-by:
Linus Torvalds <torvalds@osdl.org>
-
Linus Torvalds authored
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: RDMA/cma: Increase the IB CM retry count in CMA IPoIB: Retry failed send-only multicast group joins IB/srp: Don't schedule reconnect from srp
-
- 16 Sep, 2006 22 commits
-
-
Zoltan Sogor authored
In some special case (padding because of sync or umount) it can be possible that summary information is not fit to the end of the erase block. In these cases the collecting of summary is disabled for this erase block. The problem was that this was not respected by jffs2_sum_add_kvec(). This patch fix this bug. Signed-off-by:
Ferenc Havasi <havasi@inf.u-szeged.hu> Signed-off-by:
David Woodhouse <dwmw2@infradead.org> Signed-off-by:
-
Vitaly Wool authored
In the case of data-pad-ecc-pad-data... layout the oob start position has to be sizeof(data) in nand_write_oob_syndrom(). In nand_fill_oob() we need to copy to buf + buffer offset instead of buf + write offset. Signed-off-by:
Vitaly Wool <vwool@ru.mvista.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Suparna Bhattacharya authored
ext3-get-blocks support caused ~20% degrade in Sequential read performance (tiobench). Problem is with marking the buffer boundary so IO can be submitted right away. Here is the patch to fix it. 2.6.18-rc6: ----------- # ./iotest 1048576+0 records in 1048576+0 records out 4294967296 bytes (4.3 GB) copied, 75.2726 seconds, 57.1 MB/s real 1m15.285s user 0m0.276s sys 0m3.884s 2.6.18-rc6 + fix: ----------------- [root@elm3a241 ~]# ./iotest 1048576+0 records in 1048576+0 records out 4294967296 bytes (4.3 GB) copied, 62.9356 seconds, 68.2 MB/s The boundary block check in ext3_get_blocks_handle needs to be adjusted against the count of blocks mapped in this call, now that it can map more than one block. Signed-off-by:
Suparna Bhattacharya <suparna@in.ibm.com> Tested-by:
Badari Pulavarty <pbadari@us.ibm.com> Signed-off-by:
-
Kenneth Lee authored
I think there is a bug in kmod.c: In __call_usermodehelper(), when kernel_thread(wait_for_helper, ...) return success, since wait_for_helper() might call complete() at any time, the sub_info should not be used any more. Normally wait_for_helper() take a long time to finish, you may not get problem for most of the case. But if you remove /sbin/modprobe, it may become easier for you to get a oop in khelper. Cc: Matt Helsley <matthltc@us.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
David Woodhouse authored
`make headers_check' wants to go and write stuff in /lib/modules, which requires root, whic is unfortunate. In fact, there's no _particular_ reason for headers_install to put it there either -- it can go into a subdirectory of the build tree in both cases. It's not intended to go directly into /usr/include, which is why we didn't put it there -- and we certainly don't want people screwing around with symlinking to it. It's for distributors to take away and do stuff with, so leaving it in $(objtree) is fine, even in the headers_install case. I picked $(objtree)/usr/include but I have no _particular_ preference for that; it just seemed reasonable. Signed-off-by:
-
Chuck Ebbert authored
Fix two problems with the CONFIG_EMBEDDED submenu: (1) The menu was split in two by the rt_mutex patch, which moved half the items into the "General setup" menu. (2) CONFIG_SYSCTL and CONFIG_UID16 were added to the main menu instead of the submenu. Signed-off-by:Chuck Ebbert <76306.1226@compuserve.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Roman Zippel <zippel@linux-m68k.org> Signed-off-by:
-
David Woodhouse authored
Alpha currently fails 'make headers_check' in the 2.6.18-rc kernels. This patch fixes it, by moving the existing #ifdef __KERNEL__ in asm/page.h so that it covers everything that userspace shouldn't so, and by adding asm/compiler.h to the list of exported files so that its use within asm/byteorder.h is successful. [ Note that at least with GCC 4, <linux/compiler.h> doesn't do the forced inlining about which there are nasty comments (and a workaround) in <asm/compiler.h>, unless you set CONFIG_FORCED_INLINING. Rather than keep the mess you have in <asm/compiler.h> you could perhaps just make sure CONFIG_FORCED_INLINING=n is also honoured with GCC3, and make sure it cannot be set for Alpha? ] Signed-off-by:
-
David Woodhouse authored
On Tue, 2006-09-12 at 17:44 +0100, David Woodhouse wrote: > asm-x86_64/elf.h requires asm/processor.h, which does not exist > asm-x86_64/signal.h requires linux/linkage.h, which does not exist > asm-x86_64/unistd.h requires linux/linkage.h, which does not exist > asm-x86_64/vsyscall.h requires linux/seqlock.h, which does not exist Again, move stuff which shouldn't be visible inside (mostly already existing) #ifdef __KERNEL__. This fixes a bunch of mislabelled and unlabelled #endifs in unistd.h and also cleans that up to conform with what's visible on other architectures, since the minimal fix for the error reported about would have involved a more intrusive patch, renesting other ifdefs. Signed-off-by:
-
David Woodhouse authored
This brings i386 asm/unistd.h into consistency with other architectures by not exporting functionality which is not necessary. Signed-off-by:
-
David Woodhouse authored
On Tue, 2006-09-12 at 17:44 +0100, David Woodhouse wrote: > asm-ia64/ptrace.h requires asm/asm-offsets.h, which does not exist > asm-ia64/resource.h requires asm/ustack.h, which does not exist Hide parts which shouldn't be visible to userspace. Signed-off-by:
-
David Woodhouse authored
On Tue, 2006-09-12 at 17:44 +0100, David Woodhouse wrote: > asm-s390/debug.h requires linux/string.h, which does not exist > asm-s390/elf.h requires asm/system.h, which does not exist Move things around slightly so the right things end up within #ifdef __KERNEL__ and thus don't pollute the exported headers. Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
-
David Woodhouse authored
We generate an <asm/foo.h> which includes either <asm-$ARCH/foo.h> or <asm-$ALTARCH/foo.h> as appropriate. But we were doing this dependent on whether the file in question existed in the _unexported_ tree, not the exported tree. So if a file was exported to userspace in one asm- directory but not the other, the generated file in asm/ was incorrect. This only changed the failure mode if it _was_ included from a nice #error to a less explicable #include failure -- but it also gave false errors in 'make headers_check' output. Fix it by looking in the right place instead. Signed-off-by:
-
Josh Triplett authored
The kernel build system supports making symbol type files (*.symtypes) from C source files. Add these files to .gitignore. Signed-off-by:
Josh Triplett <josh@freedesktop.org> Signed-off-by:
-
Josh Triplett authored
The kernel build system supports making mixed source and assembly listings (*.lst) from C source files. Add these files to .gitignore. Signed-off-by:
-
Josh Triplett authored
The kernel build system supports making preprocessed files (*.i) from C source files. Add these files to .gitignore. Signed-off-by:
-
Corey Minyard authored
If one of the OEM flags becomes set in the flags from the hardware, the driver could hang if no OEM handler was set. Fix the code to handle this. This was tested by setting the flags by hand after they were fetched. Signed-off-by:
Corey Minyard <minyard@acm.org> Ackde-by:
Matt Domsch <Matt_Domsch@dell.com> Signed-off-by:
-
Ross Biro authored
Signed-off-by:
Ross Biro <rossb@google.com> Acked-by:
Sam Ravnborg <sam@ravnborg.org> Signed-off-by:
-
Andrew Morton authored
Fix http://bugzilla.kernel.org/show_bug.cgi?id=7152 Cc: Michael Tautschnig <tautschn@model.in.tum.de> Signed-off-by:
-
NeilBrown authored
Inodes earlier than the 'first' inode (e.g. journal, resize) should be rejected early - except the root inode. Also inode numbers that are too big should be rejected early. [akpm@osdl.org: cleanup] Signed-off-by:
Neil Brown <neilb@suse.de> Signed-off-by:
-
NeilBrown authored
This prevents bad inode numbers from triggering errors in ext2_get_inode. [akpm@osdl.org: speedup, cleanup] Signed-off-by:
-
Arnaud Patard authored
When the ipmi_si module is loaded on a system without any ipmi device, it fails with nodev. It would be fine if all resources were freed. A call to device_unregister() is missing, resulting to a oops when you remove the ipmi_msghandler. Signed-off-by:
Arnaud Patard <apatard@mandriva.com> Acked-by:
-
Imre Deak authored
Fix a bug where the IRQ_PENDING flag is never cleared and the ISR is called endlessly without an actual interrupt. Signed-off-by:
Imre Deak <imre.deak@solidboot.com> Acked-by:
Ingo Molnar <mingo@elte.hu> Signed-off-by:
-
- 14 Sep, 2006 3 commits
-
-
Michael S. Tsirkin authored
3 seems like a low number of IB Communication Manager retries to set; we see connections failing under stress, and in any case 3 just looks like an arbitrary number. 15 is the max value allowed by the InfiniBand spec. Signed-off-by:
Michael S. Tsirkin <mst@mellanox.co.il> Acked-by:
Sean Hefty <sean.hefty@intel.com> Signed-off-by:
Roland Dreier <rolandd@cisco.com>
-
Eli Cohen authored
When a send-only multicast group join fails, mcast->query must be set to NULL. Otherwise, IPoIB will never retry the join and the multicast group will never be reachable. Signed-off-by:
Eli Cohen <eli@mellanox.co.il> Signed-off-by:
-
Ishai Rabinovitz authored
If there is a problem in the connection, the SCSI mid-layer will eventually call srp_reset_host(), which will call srp_reconnect(), so we do not need to schedule a call to srp_reconnect_work() from srp_completion(). Removing this prevents srp_reset_host() from failing if a reconnect scheduled from srp_completion() is already in progress, which in turn was causing crashes as both SCSI midlayer and srp_reconnect() were cancelling commands. Signed-off-by:
Ishai Rabinovitz <ishai@mellanox.co.il> Signed-off-by:
-
- 13 Sep, 2006 2 commits
-
-
Dale Farnsworth authored
Fix a missing call to dma_unmap_single() in the receive path. Without this call, errors have been observed on non-cache-coherent systems. Signed-off-by Dale Farnsworth <dale@farnsworth.org> Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpcLinus Torvalds authored
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: [POWERPC] Fix G5 DART (IOMMU) race causing occasional data corruption [POWERPC] Fix MMIO ops to provide expected barrier behaviour [POWERPC] Fix interrupt clearing in kdump shutdown sequence [POWERPC] update prep_defconfig [POWERPC] kdump: Support kernels having 64k page size. [POWERPC] Implement PowerPC futex_atomic_cmpxchg_inatomic(). [POWERPC] Add new, missing argument to of_irq_map_raw() for 86xx. [POWERPC] Update defconfigs
-
