Merge branch 'davinci-next-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci into devel-stable

The MUSB driver doesn't see its platform device on DM644x EVM board anymore
since commit 73b089b0 (usb: musb: split davinci
to its own platform_driver) because the new probe is called as subsys_initcall()
now, and the device is registered later than that by the board code.  Move the
registration to davinci_evm_init() -- it's safe to do so because the MUSB core
device still gets initialized as fs_initcall() -- which is late enough for the
I2C GPIO expander (which controls VBUS) to be initialized.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This patch adds definitions for spi devices on the tnetv107x evm platform.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This patch adds SSP configuration and pin muxing info for tnetv107x
evm boards.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This patch adds an SSP platform device definition for the tnetv107x soc family.
The clock lookup entry has also been updated to match.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This patch adds an SPI master implementation that operates on top of an
underlying TI-SSP port.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

TI's sequencer serial port (TI-SSP) is a jack-of-all-trades type of serial port
device.  It has a built-in programmable execution engine that can be programmed
to operate as almost any serial bus (I2C, SPI, EasyScale, and others).

This patch adds a driver for this controller device.  The driver does not
expose a user-land interface.  Protocol drivers built on top of this layer are
expected to remain in-kernel.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Merge branch 'for-rmk-devel-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into devel-stable

Merge branch 'davinci-next' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci into devel-stable

Enable wakeups by default for any GPIO interrupts and in the suspend/resume
path narrow this down to only the the real wakeup interrupts. This approach is
based on the assumption that cpuidle ApSleep will be entered more often than
system suspend.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Fixup for genirq changes to struct irq_data on 2.6.38]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

All platform data has to be made conditional on
as to avoid cluttering the code with other #ifdef:s.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The HREFv60 variant of the MOP500 family of boards remove the
external GPIO expander and route these pins back to some of the
readily available internal GPIO pins instead.

Based on a patch by Bibek Basu <bibek.basu@stericsson.com> for
an internal kernel version.

Cc: Bibek Basu <bibek.basu@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This will centralize all GPIO pin muxing for the different boards
in the MOP500 family to a single file. It also kills off the
deprecated support for the ED (Early Drop) ASIC, this should
never be spotted in the open and ST-Ericsson have internally
deprecated this hardware.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
[Rebasing and kill old ASIC support]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Split off pin definitions for the MOP500 board family to its
own file.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The compiler warns that [rf]wimsc may be used uninitialized in
this function - the warning is actually false since the uses are
in identical if()-clauses, but it can't hurt very much to read
out the values to be modified early anyway and rid the warning.

Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The NOMADIK_GPIO_PM config option is disabled by default, not user visible,
and never selected by any other option: the code is therefore unused. The
GPIO registers need not be saved and restored since their values are
preserved when vAPE (on DB8500) is powered down.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch fixes a bug when setting SLPM register for DB8500.
When calling__nmk_gpio_set_slpm(...) offset to GPIO is now used
instead of the GPIO number itself.
Signed-off-by: Rikard Olsson <rikard.p.olsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Setting pinmux alternative C for a GPIO pin is actually not
so easy since it ivolves setting value "1" in two registers,
and since the combined result will take effect for intermediate
values (01 or 10) this will cause glitches while you wrote one
register but have not yet written the other.

This patch implements a series of kludges including an optional
machine-specific callback to avoid glitches when changing pin
mux mode to alternative C.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Coverity found that we were checking an unsigned variable for
>= zero. Type it correctly so that the check works as intended.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Suspend/resume didn't take care of pull-up and pull-down
settings and writing back the DAT register at resume can
change pull up/down settings, depending on pin input value.
Output values are now also restored.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

When GPIOs wake up the system from sleep mode, the normal GPIO interrupt
handler does not hit and the normal interrupt status register does not
contain the status. Instead the secondary GPIO handler does, and the
interrupt status needs to be retrieved from the wakeup status saved by
the suspend/resume code.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Added constant 32-pin assignment in platform data]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This will configure the platform data for the PL011, PL022
and PL180 (derivate) PrimeCells found in the Ux500 to use DMA
with the generic DMA engine for DMA40.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This will configure the platform data for the PL180, PL011 and
PL022 PrimeCells found in the U300 to use DMA with the generic
PrimeCell DMA engine for COH 901 318.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The mmci driver can handle a GPIO pin for card detect, using
IRQs and all just fine, so switch to using that. Delete the
old bogus input device hack, if userspace need to detect
MMC cards it should use udev like everyone else.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

- DMA tx and rx maps for usb channels are set to be configured at
  runtime
- MUSB is enabled with soc specific base address, irq and dma
  configurations
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

- DMA tx and rx maps for usb channels are set to be configured at
  runtime
- GPIO configurations for usb are added
- MUSB is enabled with soc specific base address, irq and dma
  configurations
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

MUSB driver has been updated to separate out BSP layer
from its generic parts, as separate driver. This patch
configures the clock with the new platform driver name.
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

USB resources and DMA40 configurations are dynamically with
the data provided in ux500_add_usb() call. Though only DMA40
configurations differ between U8500 and U5500 (USB resource
are common between them).
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The levelshifter pins were set to inverted values, fix this up.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The clock speed for the SD/MMC clock was incorrect, rectify it.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Proximity sensor is managed as an input event (SW_PROXIMITY).
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
[Named GPIO pin]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We register keypads per-UIB now, remove this.

Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The U8500 UIB contains a Synaptics RMI touchpanel and
a matrix keyboard via the TC35893 port expander device.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The ST-UIB contains a matrix keypad interfaced with the
STMPE1601 port expander and a ROHM BU2101 touch panel.
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>