- 11 Aug, 2010 40 commits
-
-
David Brownell authored
Be more consistent about runtime programming interface abuse warnings, which can reduce some confusion and trigger bugfixes. Based on an observation and patch from Jani Nikula. Also update doc to highlight some sleeping-call issues and to match some recent changes. Signed-off-by:
David Brownell <dbrownell@users.sourceforge.net> Cc: Jani Nikula <ext-jani.1.nikula@nokia.com> Cc: "Ryan Mallon" <ryan@bluewatersys.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Dmitry Eremin-Solenikov authored
Provide sane defaults for pcf857x, so the driver can be used w/o providing platform data (and thus can be simply bound via OF tree). Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Cc: Jean Delvare <khali@linux-fr.org> Cc: David Brownell <david-b@pacbell.net> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by:
-
Marc Kleine-Budde authored
The gpios on the max730x chips have support for internal pullups while in input mode. This patch adds support for configuring these pullups via platform data. A new member ("input_pullup_active") to the platform data struct is introduced. A set bit in this variable activates the pullups while the respective port is in input mode. This is a compatible enhancement since unset bits lead to disables pullups which was the default in the original driver. _Note_: the 4 lowest bits in "input_pullup_active" are unused because the first 4 ports of the controller are not used, too. Signed-off-by:Marc Kleine-Budde <mkl@pengutronix.de> Reviewed-by:
Wolfram Sang <w.sang@pengutronix.de> Cc: David Brownell <david-b@pacbell.net> Signed-off-by:
-
Geert Uytterhoeven authored
The Ricoh RP5C01 RTC contains 26 x 4 bits of NVRAM. Provide access to it via a sysfs "nvram" attribute file. Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Cc: Wan ZongShun <mcuos.com@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Christian Dietrich authored
Because CONFIG_PM is a precondition to CONFIG_ACPI, the ifdef CONFIG_PM within ifdef CONFIG_ACPI is redundant. Signed-off-by:
Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de> Acked-by:
Wan ZongShun <mcuos.com@gmail.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Roman Fietze authored
Mask out PM flag when reading the hour, always set MIL bit when writing the hour. Signed-off-by:
Roman Fietze <roman.fietze@telemotive.de> Acked-by:
-
Roy Zang authored
Add a driver for the DS3232 RTC chip via the I2C bus. Alarms are not supported in this version of the driver. [akpm@linux-foundation.org: fix Kconfig help text] Signed-off-by:
Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by:
Jingchang Lu <b22599@freescale.com> Signed-off-by:
Srikanth Srinivasan <srikanth.srinivasan@freescale.com> Signed-off-by:
Roy Zang <tie-fei.zang@freescale.com> Acked-by:
-
Wan ZongShun authored
Remove unused local variable. Signed-off-by:
-
Wan ZongShun authored
This patch does two modifications: (1) Adjust enable/disable IRQs location,enable it after rtc registration and disable it prior to unregistration. (2) Put 'platform_set_drvdata(pdev, nuc900_rtc)' in front of rtc registration still be safety, though there is no need to do this, when I move enable irq after rtc registration, I think still put 'platform_set_drvdata' before rtc registration that would be a good habit. Signed-off-by: -
Wan ZongShun authored
Make returning time checking function valid. In spite of using the 'rtc_valid_tm', nevertheless, the read time function omits its returning value, that means the 'rtc_valid_tm' is useless here. Signed-off-by:
-
Wan ZongShun authored
Use rtc_valid_tm() to check the returned struct rtc_time *tm, to avoid returning a wrong tm value. Signed-off-by:
-
Wan ZongShun authored
Use rtc_valid_tm to check the returned struct rtc_time *tm, to avoid returning a wrong tm value. Signed-off-by:
-
Wan ZongShun authored
Use rtc_valid_tm() to check returning tm for max6900, it can avoid returning wrong tm value. Signed-off-by:
Dale Farnsworth <dale@farnsworth.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Wan ZongShun authored
Use rtc_valid_tm() to check returned struct rtc_time *tm - it can avoid returning wrong tm value. Signed-off-by:
-
Roman Fietze authored
- derived from rtc-pcf8563 - no SRAM driver Signed-off-by:
-
Baruch Siach authored
This driver is based on code from Freescale which accompanies their i.MX25 PDK board, with some cleanup. Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Sascha Hauer <kernel@pengutronix.de> Acked-by:
-
Huang Weiyi authored
Signed-off-by:
Huang Weiyi <weiyi.huang@gmail.com> Acked-by:
-
Wan ZongShun authored
We shouldn't implement private ops->ioctl() unless absolutely necessary. pxa series RTC driver's ioctl() is unnecessary, since RTC subsystem has implement the ioctl() very well,so we can only use the API of '.alarm_irq_enable' and '.update_irq_enable' to do enable irq action. Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Acked-by:
Eric Miao <eric.y.miao@gmail.com> Cc: Paul Gortmaker <p_gortmaker@yahoo.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Sergey Matyukevich authored
- add sanity check for alarm data in fm3130_probe - fix fm3130_set_alarm. According to the datasheet, setting match bit '0' indicates that the corresponding alarm field will be used in the match process - add operation alarm_irq_enable operation which is responsible for handling RTC_AIE_ON, RTC_AIE_OFF ioctls - remove clearing of AF bit after reading rtc/alarm control register: according to datasheet this bit is cleared anyway when rtc/alarm control register is read [akpm@linux-foundation.org: make fm3130_alarm_irq_enable() static, fix comment layout] Signed-off-by:
Sergey Matyukevich <geomatsi@gmail.com> Acked-by:
Sergey Lapin <slapin@ossfans.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
-
Wan ZongShun authored
Remove six unused fields from `struct rtc_plat_data'. Signed-off-by:
-
Wan ZongShun authored
Signed-off-by:
-
Wan ZongShun authored
pxa_rtc.rtc_alarm is unused. Signed-off-by:
-
Graham Gower authored
Signed-off-by:
Graham Gower <graham.gower@gmail.com> Acked-by:
-
Wan ZongShun authored
When a user application wants to set the rtc time, the RTC subsystem takes advantage of 'rtc_valid_tm(tm)' to check 'rtc_time *tm' value validity, it make sure the 'tm->tm_year' is larger than 70,so if '70< tm_year < 100', the '(settm->tm_year - 100)' will be negative. ' Setting the negative value to hardware register will be invalid, so I add the 'if' condition to make sure set a valid value to register. Signed-off-by:
-
Wan ZongShun authored
- add an mdelay(1) to the polling loop to cause less frequent access to the hardware register. - change the return value from ENODEV to EPERM if the loop timed out. I think the 'Operation not permitted' description is more suitable for the meaning of 'check_rtc_access_enable()' function, it just be used to judge rtc access operation is permitted or not. Signed-off-by:
-
Dan Carpenter authored
After 97e7449a: "autofs4: fix indirect mount pending expire race" we no longer assumed that "ino" can be null. The other null checks got removed but this was one was missed. Signed-off-by:
Dan Carpenter <error27@gmail.com> Cc: Ian Kent <raven@themaw.net> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Kulikov Vasiliy authored
Check return value of put_user() and return -EFAULT if it failed. Original comment "We did a get user...so assuming mem is ok...is this bad?" is incorrect because memory can be read only. Signed-off-by:
Kulikov Vasiliy <segooon@gmail.com> Signed-off-by:
-
Kulikov Vasiliy authored
If (len > reslen) we must not call copy_to_user() since kernel buffer is smaller than we want to copy. Similar code in this file is correct, so this bug was a typo. Signed-off-by:
-
Julia Lawall authored
Add a mutex_unlock missing on the error path. The semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression E1; @@ * mutex_lock(E1,...); <+... when != E1 if (...) { ... when != E1 * return ...; } ...+> * mutex_unlock(E1,...); // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Signed-off-by:
-
Pablo Castillo authored
Signed-off-by:
Pablo Castillo <CyberCastle@gmail.com> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Tested-by:
Gregg Lebovitz <gregg@lebovitz.net> Cc: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by:
-
Roy Zang authored
P4080 ESDHC controller does not support 1.8V and 3.0V voltage. but the host controller capabilities register wrongly set the bits. This patch adds the workaround to correct the weird voltage setting bits. Only 3.3V voltage is supported for P4080 ESDHC controller. Signed-off-by:
-
Roy Zang authored
Signed-off-by:
-
Jerry Huang authored
Add auto CMD12 command support for eSDHC driver. This is needed by P4080 and P1022 for block read/write. Manual asynchronous CMD12 abort operation causes protocol violations on these silicons. Signed-off-by:
Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by:
-
Marek Szyprowski authored
This patch adds support for regulator API to sdhci core driver. Regulators can be used to disable power in suspended state to reduce dissipated energy. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Marek Szyprowski authored
On some Samsung SoCs not all SDHCI controllers have card detect (CD) line. For some embedded designs it is not even needed, because ususally the device (like SDIO flash memory or wifi controller) is permanently wired to the controller. There are also systems which have a card detect line connected to some of the external interrupt lines or the presence of the card depends on some other actions (like enabling a power regulator). This patch adds support for all these cases. The following card detection methods are possible: 1. internal sdhci host card detect line 2. external event 3. external gpio interrupt 4. no card detect line, controller will poll for the card 5. no card detect line, card is permanently wired to the controller (once detected host won't poll it any more) By default, all existing code would use method #1, what is compatible with the previous version of the driver. In case of external event, two callbacks must be provided in platdata: ext_cd_init and ext_cd_cleanup. Both of them get a callback to a function that notifies the s3c-sdhci host contoller as their argument. That callback function should be called from the even dispatcher to let host notice the card insertion/removal. In case of external gpio interrupt, a gpio pin number must be provided in platdata (ext_cd_gpio parameter), as well as the information about the polarity of that gpio pin (ext_cd_gpio_invert). By default (ext_cd_gpio_invert == 0) gpio value 0 means 'card has been removed', but this can be changed to 'card has been removed' when ext_cd_gpio_invert == 1. This patch adds all required changes to sdhci-s3c driver. Signed-off-by:
-
Marek Szyprowski authored
This patch enables SDHCI_QUIRK_NO_HISPD_BIT on Samsung SDHCI driver. This solves detection problems with some external SD cards. This change has been tested on S5PC100 and S5PC110. It has no inpact on driver speed. Signed-off-by:
-
Marek Szyprowski authored
S3C SDHCI host controller can change the source for generating mmc clock. By default host bus clock is used, what causes some problems on machines with 133MHz bus, because the SDHCI divider cannot be as high get proper clock value for identification mode. This is not a problem for the controller, because it can generate lower frequencies from other clock sources. This patch changes sdhci driver to use get_min_clock() call if it has been provided. This fixes the flood of the following warnings on Samsung S5PV210 SoCs: mmc0: Minimum clock frequency too high for identification mode Signed-off-by:
-
Hyuk Lee authored
On Samsung's SDMMC hosts the timeout clock is derivied from the SD Clock which is set dynamically. So checked SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK quirk and removed 'sdhci_s3c_get_timeout_clk' callback which doesn't need any more. Signed-off-by:
Hyuk Lee <hyuk1.lee@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Venkatraman S authored
If other informative interrupts are enabled for the DMA channel used by hsmmc, those are incorrectly treated as block completion. This patch lets only the block completion interrupt to be processed. Signed-off-by:
Venkatraman S <svenkatr@ti.com> Acked-by:
Madhusudhan Chikkature <madhu.cr@ti.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
Christian Dietrich authored
CONFIG_MMC_MSM7X00A_RESUME_IN_WQ and CONFIG_MMC_EMBEDDED_SDIO don't exist in Kconfig and is never defined anywhere else, therefore removing all references for it from the source code. Signed-off-by:
David Brown <davidb@codeaurora.org> Cc: Daniel Walker <dwalker@codeaurora.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by:
-
