Trivial fix removes unneeded semicolons after switch blocks.
Signed-off-by: Christopher Díaz Riveros <chrisadr@gentoo.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For correct interpretation of a tx rate, the corresponding rate flags are
needed (e.g. whether a HT-MCS rate or a legacy rate) and moreover for more
correct simulation the other infos of the flags are important (like
short-GI). Keeping compatibility, the flags are not integrated into the
existing hwsim_tx_rate, but transmitted as an additional netlink attribute.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This patch adds a rhastable for mac address lookup of hwsim radios. This
especially improve the speed on reception of a netlink message with a new
frame. Although redundant, we keep holding a normal list for all radios,
since the rhashtable_walk interface adds a lot of overhead for iterating
over all radios and the doc of rhashtable recommend a redundant structure
for stable walks in such situations.

Since rhashtable is rcu protected we do not need a lock for delivering
frames and thus improving this scenario.
Signed-off-by: Benjamin Beichler <benjamin.beichler@uni-rostock.de>
[remove hash function, it would cause alignment issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2018-01-12

This series contains updates to ixgbe, fm10k and net core.

Alex updates the driver to remove a duplicate MAC address check and
verifies that we have not run out of resources to configure a MAC rule
in our filter table.  Also do not assume that dev->num_tc was populated
and configured with the driver, since it can be configured via mqprio
without any hardware coordination.  Fixed the recording of stats for
MACVLAN in ixgbe and fm10k instead of recording the receive queue on
MACVLAN offloaded frames.  When handling a MACVLAN offload, we should
be stopping/starting traffic on our own queues instead of the upper
devices transmit queues.  Fixed possible race conditions with the
MACVLAN cleanup with the interface cleanup on shutdown.  With the
recent fixes to ixgbe, we can cap the number of queues regardless of
accel_priv being in use or not, since the actual number of queues are
being reported via real_num_tx_queues.

Tony fixes up the kernel documentation for ixgbe and ixgbevf to resolve
warnings when W=1 is used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: Offload PRIO qdisc

Nogah says:

Add an offload support for PRIO qdisc for mlxsw driver.
PRIO qdisc is being offloaded by using ndo_setup_tc. It has three
commands, to set or tune the qdisc, to remove it and to get its stats.

Like RED offloading, offloading this qdisc is not enforced on the driver
and determining its offload state is done in the dump action, when the
stats are being updated.
In the driver, offloading of PRIO is supported as root qdisc only. It
supports only priorities 0-7 (the range that is used by the current static
mapping of DSCP to skb prio and by 1:1 PCP values mapping) and up to 8
bands.

Patches 1-2 offload DSCP to priority mapping in the mlxsw_sp driver.
Patch 3 adds offload support for PRIO qdisc.
Patches 4-5 Add PRIO offload support in the mlxsw_sp driver.

---
v1->v2:
- Patch 1/5:
 - Rewrite patch msg
- Patch 3/5:
 - Send all the qstats in the replace command (and not just backlog)
- Patch 5/5:
 - Align with the changes from 3/5
 - Move backlog to the generic qdisc stats struct
 - Delete extra newline
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Support basic stats for PRIO qdisc, which includes tx packets and bytes
count, drops count and backlog size. The rest of the stats are irrelevant
for this qdisc offload.
Since backlog is not only incremental but reflecting momentary value, in
case of a qdisc that stops being offloaded but is not destroyed, backlog
value needs to be updated about the un-offloading.
For that reason an unoffload function is being added to the ops struct.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for offloading PRIO qdisc as root qdisc.
The support is for up to 8 bands.
Routed packets priority is determined by the DSCP field with the default
translations. Bridged packets priority is determined by the PCP field, if
exist, otherwise it is set to 0.
Since both options have only priorities 0-7, higher priorities mapping are
being ignored.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the ability to offload PRIO qdisc by using ndo_setup_tc.
There are three commands for PRIO offloading:
* TC_PRIO_REPLACE: handles set and tune
* TC_PRIO_DESTROY: handles qdisc destroy
* TC_PRIO_STATS: updates the qdiscs counters (given as reference)

Like RED qdisc, the indication of whether PRIO is being offloaded is being
set and updated as part of the dump function. It is so because the driver
could decide to offload or not based on the qdisc parent, which could
change without notifying the qdisc.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When routing ip packets, the kernel is setting the SKB's priority
based on the tos field of the packet.
Imitate this behavior in the mlxsw router, having the internal
switch priority of a routed packet determined according to its DS
field.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add rdpm definition - router DSCP to priority mapping register.
This register will be utilized later to align the default mapping between
packet DSCP and switch-priority to the kernel's mapping between
packet priority and skb priority.

This is the first non-bit indexed register where the entries are arranged
in descending order, i.e., entry at offset 0 matches configuration for
dscp[63]. As a result, the item's step is converted into a signed variable
to support descending arrays [where step would be negative].
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
mv88e6xxx: ATU and VTU interrupts

Both the ATU and VTU of Mavell switches can generate interrupts when
violations occur.  Trap this interrupts and print what violation
occurred.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When there is a problem with the VTU, an interrupt can be
generated. Trap this interrupt and decode the registers to determine
what the problem was, then log the error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When there is a problem with the ATU, an interrupt can be
generated. Trap this interrupt and decode the registers to determine
what the problem was, then log the error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit eb789980 ("mlxsw: spectrum_router: Populate adjacency
entries according to weights") the driver includes support for
non-equal-cost multipath, but IPv4 nexthops were the only user.

Now that the kernel supports weighted IPv6 nexthops, we can extend the
driver to support it as well.

This is done by assigning each nexthop its configured weight, so that it
will be populated accordingly in the device's adjacency table. The
`weight` parameter is also taken into account when comparing nexthop
groups in order not to consolidate non-identical groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On targets that have different sizes for phys_addr_t and dma_addr_t,
we get a type mismatch error:

drivers/net/ethernet/socionext/netsec.c: In function 'netsec_alloc_dring':
drivers/net/ethernet/socionext/netsec.c:970:9: error: passing argument 3 of 'dma_zalloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]

The code is otherwise correct, as the address is never actually used as a
physical address but only passed into a DMA register.  For consistently,
I'm changing the variable name as well, to clarify that this is a DMA
address.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent checks added for formatting kernel-doc comments are causing warnings
if W= is run with a non-zero value.  This patch fixes function comments to
resolve warnings when W=1 is used.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Recent checks added for formatting kernel-doc comments are causing warnings
if W= is run with a non-zero value.  This patch fixes function comments to
resolve warnings when W=1 is used.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

With the recent fix to ixgbe we can cap the number of queues always
regardless of if accel_priv is being used or not since the actual number of
queues are being reported via real_num_tx_queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This update makes it so that we report the actual number of Tx queues via
real_num_tx_queues but are still restricted to RSS on only the first pool
by setting num_tc equal to 1. Doing this locks us into only having the
ability to setup XPS on the queues in that pool, and only those queues
should be used for transmitting anything other than macvlan traffic.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that instead of bringing rings up/down for various
we just update the netdev pointer for the Rx ring and set or clear the MAC
filter for the interface. By doing it this way we can avoid a number of
races and issues in the code as things were getting messy with the macvlan
clean-up racing with the interface clean-up to bring the rings down on
shutdown.

With this change we opt to leave the rings owned by the PF interface for
both Tx and Rx and just direct the packets once they are received to the
macvlan netdev.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We should not be stopping/starting the upper devices Tx queues when
handling a macvlan offload. Instead we should be stopping and starting
traffic on our own queues.

In order to prevent us from doing this I am updating the code so that we no
longer change the queue configuration on the upper device, nor do we update
the queue_index on our own device. Instead we can just use the queue index
for our local device and not update the netdev in the case of the transmit
rings.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We shouldn't be recording the Rx queue on macvlan offloaded frames since
the macvlan is normally brought up as a single queue device, and it will
trigger warnings for RPS if we have recorded queue IDs larger than the
"real_num_rx_queues" value recorded for the device.

Instead we should be recording the macvlan statistics since we are
bypassing the normal macvlan statistics that would have been generated by
the receive path.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The code throughout ixgbe was assuming that dev->num_tc was populated and
configured with the driver, when in fact this can be configured via mqprio
without any hardware coordination other than restricting us to the real
number of Tx queues we advertise.

Instead of handling things this way we need to keep a local copy of the
number of TCs in use so that we don't accidentally pull in the TC
configuration from mqprio when it is configured in software mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We might as well configure the limit to default to 1 pool always for the
interface. This accounts for the fact that the PF counts as 1 pool if
SR-IOV is enabled, and in general we are always running in 1 pool mode when
RSS or DCB is enabled as well, though we don't need to actually evaluate
any of the VMDq features in those cases.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The macvlan driver itself will validate the MAC address that is configured
for a given interface. There is no need for us to verify it again.

Instead we should be checking to verify that we actually allocate the filter
and have not run out of resources to configure a MAC rule in our filter
table.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Peng Li says:

====================
hns3: add some new features and fix some bugs

This patchset adds 3 ethtool features: get_channels,
get_coalesce and get_coalesce, and fix some bugs.

[patch 1/11] adds ethtool_ops.get_channels (ethtool -l) support
for VF.

[patch 2/11] removes TSO config command from VF driver,
as only main PF can config TSO MSS length according to
hardware.

[patch 3/11 - 4/11] add ethtool_ops {get|set}_coalesce
(ethtool -c/-C) support to PF.
[patch 5/11 - 9/11] fix some bugs related to {get|set}_coalesce.

[patch 10/11 - 11/11] fix the features handling in
hns3_nic_set_features(). Local variable "changed" was defined
to indicates features changed, but was used only for feature
NETIF_F_HW_VLAN_CTAG_RX. Add checking to improve the reliability.

---
Change log:
V1 -> V2:
1, Rewrite the cover letter requested by David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It's necessary to check hook whether being defined before
calling, improve the reliability.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Local variable "changed" was defined to indicates features changed,
but was used only for feature NETIF_F_HW_VLAN_CTAG_RX. Add checking
for other features.

Fixes: 052ece6d ("net: hns3: add ethtool related offload command")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the int_gl_idx does not be set, the default interrupt coalesce index
is 0. The TX queues and the RX queues will both use the GL0 as the
interrupt coalesce GL switch. But it should be GL1 for TX queues and GL0
for RX queues.

This patch adds the int_gl_idx setup for TX queues and RX queues.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Previously, driver used 2us as the GL unit. The time unit ethtool
command "-c" and "-C" use is 1us, so now the GL unit driver uses
actually is 1us.

This patch changes the unit of GL value macro from
2us to 1us.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the TX GL and the RX GL need to be set separately,
hns3_set_vector_coalesc_gl() has been replaced with
hns3_set_vector_coalesce_rx_gl() and hns3_set_vector_coalesce_tx_gl().

This patch removes hns3_set_vector_coalesc_gl().
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GL update function uses the max GL value between tx_int_gl and
rx_int_gl to set both new tx_int_gl and new rx_int_gl. Therefore, User
can not enable TX GL self-adaptive or RX GL self-adaptive individually.

This patch refactors the code to update the TX GL and the RX GL
separately, making user can enable TX GL self-adaptive or RX GL
self-adaptive individually.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the hardware, the coalesce configurable registers include GL0, GL1,
GL2. In the driver, the TX queues use the register GL1 and the RX queues
use the register GL0. This function initializes the configuration of the
interrupt coalescing, but does not distinguish between the TX direction
and the RX direction. It will cause some confusion.

This patch refactors the function to initialize the TX GL and the RX GL
separately. And the initialization of related variables also is added to
this patch.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds ethtool_ops.set_coalesce support to PF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds ethtool_ops.get_coalesce support to PF.

Whilst our hardware supports per queue values, external interfaces
support only a single shared value. As such we use the values for
queue 0.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only main PF can config TSO MSS length according to hardware.
This patch removes TSO config command from VF driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch supports the ethtool's get_channels() for VF.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.

Also, we should attempt to patch BPF call args if JIT always on is
enabled.  Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ceph fixes from Ilya Dryomov:
 "Two rbd fixes for 4.12 and 4.2 issues respectively, marked for
  stable"

* tag 'ceph-for-4.15-rc8' of git://github.com/ceph/ceph-client:
  rbd: set max_segments to USHRT_MAX
  rbd: reacquire lock should update lock owner client id

Pull GPIO fix from Linus Walleij:
 "Fix a raw vs elaborate GPIO descriptor bug introduced by yours truly"

* tag 'gpio-v4.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: Add missing open drain/source handling to gpiod_set_value_cansleep()