- 27 Jan, 2013 23 commits
-
-
Bruce Allan authored
Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Bruce Allan authored
The e1000e driver has been converted to use extended descriptors instead of the older legacy descriptor type. Signed-off-by:
-
Bruce Allan authored
Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it back to power-on defaults. This includes setting it's MAC-PHY messaging mode to use the PCIe-like interconnect, so the MAC must also be set back from SMBus mode to PCIe mode otherwise the PHY can be inaccessible. Signed-off-by:
Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by:
-
Bruce Allan authored
The largest jumbo frame supported by the i217 and i218 hardware is 9018. Signed-off-by:
-
Bruce Allan authored
Signed-off-by:
-
Bruce Allan authored
Signed-off-by:
-
Bruce Allan authored
As done with the previous generation managed 82579, prevent the PHY from being put into an unknown state by blocking the hardware from automatically configuring the PHY as done with the previous generation managed 82579. Instead, the driver should configure the PHY with contents of the EEPROM image. Signed-off-by:
-
Bruce Allan authored
In rare instances, memory errors have been detected in the internal packet buffer memory on I217/I218 when stressed under certain environmental conditions. Enable Error Correcting Code (ECC) in hardware to catch both correctable and uncorrectable errors. Correctable errors will be handled by the hardware. Uncorrectable errors in the packet buffer will cause the packet to be received with an error indication in the buffer descriptor causing the packet to be discarded. If the uncorrectable error is in the descriptor itself, the hardware will stop and interrupt the driver indicating the error. The driver will then reset the hardware in order to clear the error and restart. Both types of errors will be accounted for in statistics counters. Signed-off-by:
-
Bruce Allan authored
Add PTP IEEE-1588 support and make accesible via the PHC subsystem. v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Richard Cochran <richardcochran@gmail.com> Signed-off-by:
Jacob Keller <Jacob.e.keller@intel.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Tested-by:
-
Bruce Allan authored
The previous static flow-control thresholds were causing unnecessary pause packets to be transmitted when jumbo frames are configured reducing the throughput. Signed-off-by:
-
Bruce Allan authored
The SHRAH[9] register on I217 has a different R/W bit-mask than RAR and SHRAL/H registers. Set R/W bit-mask appropriately for SHRAH[9] when testing the R/W ability of the register. Also, fix the error message log format so that it does not provide misleading information (i.e. the logged register address could be incorrect). Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-nextDavid S. Miller authored
Signed-off-by:David S. Miller <davem@davemloft.net>
-
Tom Herbert authored
Fix a reported compilation error where ia variable of type kuid_t was being set to zero. Eliminate two instances of setting tb->fastuid to zero. tb->fastuid is only used if tb->fastreuseport is set, so there should be no problem if tb->fastuid is not initialized (when tb->fastreuesport is zero). Signed-off-by:
Tom Herbert <therbert@google.com> Signed-off-by:
-
Thomas Graf authored
Commit 055dc21a (soreuseport: infrastructure) removed the #if 0 around SO_REUSEPORT without removing the corresponding #endif thus causing the header guard to close early. Cc: Tom Herbert <therbert@google.com> Signed-off-by:
Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
Jitendra Kalsaria authored
Signed-off-by:
Jitendra Kalsaria <jitendra.kalsaria@qlogic.com> Signed-off-by:
-
Jitendra Kalsaria authored
Providing communication channel between KVM and e-Switch so that it can be informed when hypervisor configures a MAC address and VLAN. qlcnic_mac_learn module param usage will be changed to: 0 = MAC learning is disable 1 = Driver learning is enable 2 = FDB learning is enable Signed-off-by:
-
Jitendra Kalsaria authored
device eth0 entered promiscuous mode BUG: sleeping function called from invalid context at mm/slub.c:930 in_atomic(): 1, irqs_disabled(): 0, pid: 5911, name: brctl INFO: lockdep is turned off. Pid: 5911, comm: brctl Tainted: GF W O 3.6.0-0.rc7.git1.4.fc18.x86_64 #1 Call Trace: [<ffffffff810a29ca>] __might_sleep+0x18a/0x240 [<ffffffff811b5d77>] __kmalloc+0x67/0x2d0 [<ffffffffa00a61a9>] ? qlcnic_alloc_lb_filters_mem+0x59/0xa0 [qlcnic] [<ffffffffa00a61a9>] qlcnic_alloc_lb_filters_mem+0x59/0xa0 [qlcnic] [<ffffffffa009e1c1>] qlcnic_set_multi+0x81/0x100 [qlcnic] [<ffffffff8159cccf>] __dev_set_rx_mode+0x5f/0xb0 [<ffffffff8159cd4f>] dev_set_rx_mode+0x2f/0x50 [<ffffffff8159d00c>] dev_set_promiscuity+0x3c/0x50 [<ffffffffa05ed728>] br_add_if+0x1e8/0x400 [bridge] [<ffffffffa05ee2df>] add_del_if+0x5f/0x90 [bridge] [<ffffffffa05eee0b>] br_dev_ioctl+0x4b/0x90 [bridge] [<ffffffff8159d613>] dev_ifsioc+0x373/0x3b0 [<ffffffff8159d78f>] dev_ioctl+0x13f/0x860 [<ffffffff812dd6e1>] ? avc_has_perm_flags+0x31/0x2c0 [<ffffffff8157c18d>] sock_do_ioctl+0x5d/0x70 [<ffffffff8157c21d>] sock_ioctl+0x7d/0x2c0 [<ffffffff812df922>] ? inode_has_perm.isra.48.constprop.61+0x62/0xa0 [<ffffffff811e4979>] do_vfs_ioctl+0x99/0x5a0 [<ffffffff812df9f7>] ? file_has_perm+0x97/0xb0 [<ffffffff810d716d>] ? trace_hardirqs_on+0xd/0x10 [<ffffffff811e4f19>] sys_ioctl+0x99/0xa0 [<ffffffff816e7369>] system_call_fastpath+0x16/0x1b br0: port 1(eth0) entered forwarding state br0: port 1(eth0) entered forwarding state Signed-off-by:
-
Himanshu Madhani authored
Provide port number in command payload for LED/Beaconing tests. Signed-off-by:
Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by:
-
Manish chopra authored
o Some adapter types do not support co-existence of Legacy Interrupt with MSI-x or MSI among multiple functions. For those adapters, prevent attaching to a function during normal load, if MSI-x or MSI vectors are not available. o Using module parameters use_msi=0 and use_msi_x=0, driver can be loaded in legacy mode for all functions in the adapter. Signed-off-by:
Manish Chopra <manish.chopra@qlogic.com> Signed-off-by:
-
Shahed Shaikh authored
o This patch enables RSS for TYPE-C packets to enable RSS for TCP over IPv6 Signed-off-by:
Shahed Shaikh <shahed.shaikh@qlogic.com> Signed-off-by:
-
Shahed Shaikh authored
Signed-off-by:
-
Sritej Velaga authored
Signed-off-by:
Sritej Velaga <sritej.velaga@qlogic.com> Signed-off-by:
-
git://1984.lsi.us.es/nf-nextDavid S. Miller authored
Pablo Neira Ayuso says: ==================== This batch contains netfilter updates for you net-next tree, they are: * The new connlabel extension for x_tables, that allows us to attach labels to each conntrack flow. The kernel implementation uses a bitmask and there's a file in user-space that maps the bits with the corresponding string for each existing label. By now, you can attach up to 128 overlapping labels. From Florian Westphal. * A new round of improvements for the netns support for conntrack. Gao feng has moved many of the initialization code of each module of the netns init path. He also made several code refactoring, that code looks cleaner to me now. * Added documentation for all possible tweaks for nf_conntrack via sysctl, from Jiri Pirko. * Cisco 7941/7945 IP phone support for our SIP conntrack helper, from Kevin Cernekee. * Missing header file in the snmp helper, from Stephen Hemminger. * Finally, a couple of fixes to resolve minor issues with these changes, from myself. ==================== Signed-off-by:
-
- 23 Jan, 2013 17 commits
-
-
Greg Rose authored
The X540 can link at 100Mbps - fix the link speed indicator message to show that value. Signed-off-by:
Greg Rose <gregory.v.rose@intel.com> Tested-by:
Sibai Li <sibai.li@intel.com> Signed-off-by:
-
Donald Dutile authored
ixgbe claims it supports 64 VFs in its SRIOV capability structure, but the driver only supports 63. Adjust it so sysfs sriov configuration checking will check with the proper totalvf value. Signed-off-by:
Donald Dutile <ddutile@redhat.com> Acked-by:
Phil Schmitt <phillip.j.schmitt@intel.com> Tested-by:
-
Greg Rose authored
Implement callbacks in the driver for the new PCI bus driver interface that allows the user to enable/disable SR-IOV VFs in a device via the sysfs interface. Signed-off-by:
-
Greg Rose authored
In preparation for enable/disable of SR-IOV via the PCI sysfs interface move some core SR-IOV enablement code that would be common to module parameter usage or callback from the PCI bus driver to a separate function so that it can be used by either method. Signed-off-by:
-
Greg Rose authored
There is no actual dependency on initialization of the mailbox ops on whether SR-IOV is enabled or not and it doesn't hurt to go ahead and initialize ops unconditionally. Move the initialization into the device probe so that the mailbox ops are initialized at the time we have the board info necessary to do it. Signed-off-by:
-
Jacob Keller authored
This patch modifies ixgbe_debugfs.c and the Makefile for the ixgbe driver to only compile the file when the config is enabled. This means we can remove the #ifdef inside the ixgbe_debugfs.c file. Signed-off-by:
-
Alexander Duyck authored
This change is meant to inline the Rx PTP descriptor handling. The main motivation is to avoid unnecessary jumps into function calls that we then immediately exit because we are not performing timestamps. The net result of this change is that ixgbe_ptp_rx_tstamp drops from .5% CPU utilization in my performance runs to 0%, and the only value tested is the Rx descriptor which should already be warm in the cache if not stored in a register. Cc: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
Alexander Duyck <alexander.h.duyck@intel.com> Acked-by:
-
Jacob Keller authored
This patch corrects a bug introduced by commit f3444d8b. The rxmtrl value for the UDP port to timestamp on was moved above the switch statement, but was overwritten to 0 if the ioctl selected one of the V1 filters. Signed-off-by:
-
Jacob Keller authored
This patch adds warnings when a reset of the adapter is scheduled so that the user can see log of why the reset occurred. Signed-off-by:
-
Jacob Keller authored
This patch copies the igb implementation of Tx timestamps, which uses a work item to poll for the Tx timestamp. In addition it adds a timeout value of 15 seconds, after which it will stop polling. This is necessary due to an issue with the descriptor being marked done before the Tx timestamp event has occurred. These two events don't correlate, so using the done bit on the descriptor as indication that the timestamp must already have been taken leads to potentially dropped Tx timestamps (especially under heavy packet load) Reported-by:
Matthew Vick <matthew.vick@intel.com> Signed-off-by:
-
Jacob Keller authored
This patch removes ixgbe_ptp_match, and the corresponding packet filtering from ixgbe driver. This code was previously causing some issues within the hotpath of the driver. However the code also provided a check against possible frozen Rx timestamp due to dropped packets when the Rx ring is full. This patch provides a replacement solution based on the watchdog. To this end, whenever a packet consumes the Rx timestamp it stores the jiffy value in the rx_ring structure. Watchdog updates its own jiffy timer whenever there is no valid timestamp in the registers. If watchdog detects a valid timestamp in the registers, (meaning that no Rx packet has consumed it yet) it will check which time is most recent, the last time in the watchdog, or any time in the rx_rings. If the most recent "event" was more than 5seconds ago, it will flush the Rx timestamp and print a warning message to the syslog. Reported-by:
-
Jacob Keller authored
This patch fixes the comment on ptp_overflow_check to match up with what is currently used as the parameters. Also change the jiffies check to use time_is_after_jiffies macro. Signed-off-by:
-
Jacob Keller authored
This patch updates the filters for ethtool's get_ts_info to return support for all filters which can be supported by upscaling to ptp_v2_event. The intent behind this change is due to reasoning that we do in fact support the filters. (hwtstamp_ioctl returns success after setting the filter to the upscaled version). In this way we can remain consistent over which filters are supported via the get_ts_info ioctl and which filters are in practice actually supported. Signed-off-by:
-
Jacob Keller authored
This patch cleans up the ethtool diagnostics test by ensuring that the tests work properly regardless of what state the adapter was in. The SRIOV VF check is done at the beginning, forgoing the link test. The if_running -> dev_close is moved before the link test, as well as a call to enable the Tx laser. This ensures that the link test will return valid results even when adapter was previously down. Also, a call to disable the Tx laser is added if the device was down before the start. This ensures consistent behavior of the Tx laser before and after the diagnostic checks. The end result is consistent behavior regardless of device state. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-nextDavid S. Miller authored
Steffen Klassert says: ==================== 1) Add a statistic counter for invalid output states and remove a superfluous state valid check, from Li RongQing. 2) Probe for asynchronous block ciphers instead of synchronous block ciphers to make the asynchronous variants available even if no synchronous block ciphers are found, from Jussi Kivilinna. 3) Make rfc3686 asynchronous block cipher and make use of the new asynchronous variant, from Jussi Kivilinna. 4) Replace some rwlocks by rcu, from Cong Wang. 5) Remove some unused defines. ==================== Signed-off-by: -
Ariel Elior authored
When posting a message on the bulletin board, the PF calculates crc over the message and places the result in the message. When the VF samples the Bulletin Board it copies the message aside and validates this crc. The length of the message is crucial here and must be the same in both parties. Since the PF is running in the Hypervisor and the VF is running in a Vm, they can possibly be of different versions. As the Bulletin Board is designed to grow forward in future versions, in the VF the length must not be the size of the message structure but instead it should be a field in the message itself. Signed-off-by:
Ariel Elior <ariele@broadcom.com> Signed-off-by:
Yuval Mintz <yuvalmin@broadcom.com> Signed-off-by:
-
Yuval Mintz authored
Commit 823e1d90 caused bnx2x to fail once BNX2X_STOP_ON_ERROR is set. Fixes compilation by moving function declarations between header files. Signed-off-by:
-
