CIK (DCE8) hw cursors are programmed the same as evergreen
(DCE4) with the following caveats:
- cursors are now 128x128 pixels
- new alpha blend enable bit

v2: rebase
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

No support for reading the temperature yet.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v2: further updates
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v2: further updates
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v2: further updates
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v2: update to latest driver changes
v3: properly tear down vm on suspend
v4: fix up irq init ordering
v5: remove outdated comment
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>

Async page table updates using the sDMA engine.  sDMA has a
special packet for updating entries for contiguous pages
that reduces overhead.

v2: add support for and use the CP for now.
v3: update for 2 level PTs
v4: rebase, fix DMA packet
v5: switch to using an IB
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update the page table base address and flush the
VM TLB using the sDMA.

V2: update for 2 level PTs
V3: update vm flush
V4: update SH_MEM* regs
V5: switch back to old style VM TLB invalidate
V6: fix packet formatting
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

CIK has new asynchronous DMA engines called sDMA
(system DMA).  Each engine supports 1 ring buffer
for kernel and gfx and 2 userspace queues for compute.

TODO: fill in the compute setup.

v2: update to the latest reset code
v3: remove ib_parse
v4: fix copy_dma()
v5: drop WIP compute sDMA queues
v6: rebase
v7: endian fixes for IB
v8: cleanup for release
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Todo:
- handle interrupts for compute queues

v2: add documentation
v3: update to latest reset code
v4: update to latest illegal CP handling
v5: fix missing break in interrupt handler switch statement
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

RLC handles the interrupt controller and other tasks
on the GPU.

v2: add documentation
v3: update programming sequence
v4: additional setup
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update the page table base address and flush the
VM TLB using the CP.

v2: update for 2 level PTs
v3: use new packet for invalidate
v4: update SH_MEM* regs when flushing the VM
v5: add pfp sync, go back to old style vm TLB invalidate
v6: fix hdp flush packet count
v7: use old style HDP flush
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v2: add documenation
v3: update the latest ib changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

For gfx ring only.  Compute is still todo.

v2: add documentation
v3: update to latest reset changes, integrate emit update patch.
v4: fix count on wait_reg_mem for HDP flush
v5: use old hdp flush method for fence
v6: set valid bit for IB
v7: cleanup for release
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Sets up the GFX ring and loads ucode for GFX and Compute.

Todo:
- handle compute queue setup.

v2: add documentation
v3: integrate with latest reset changes
v4: additional init fixes
v5: scratch reg write back no longer supported on CIK
v6: properly set CP_RB0_BASE_HI
v7: rebase
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Load the GDDR5 ucode and train the links.

v2: update ucode
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Currently the driver required 6 sets of ucode:
1. pfp - pre-fetch parser, part of the GFX CP
2. me - micro engine, part of the GFX CP
3. ce - constant engine, part of the GFX CP
4. rlc - interrupt, etc. controller
5. mc - memory controller (discrete cards only)
6. mec - compute engines, part of Compute CP

V2: add documentation
V3: update MC ucode
V4: rebase
V5: update mc ucode
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Redirect invalid memory accesses to the default page
instead of locking up the memory controller.

v2: rebase on top of 2 level PTs
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

The vm callbacks are the same as the SI ones right now
(same regs and bits). We could share the SI variants, and
I may yet do that, but I figured I would add CIK specific
ones for now in case we need to change anything.

V2: add documentation, minor fixes.
V3: integrate vram offset fixes for APUs
V4: enable 2 level VM PTs
V5: index SH_MEM_* regs properly
V6: add ib_parse()
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v2: split soft reset into compute and gfx.  Still need
to make reset more fine grained, but this should be a
start.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

v2: tiling fixes
v3: more tiling fixes
v4: more tiling fixes
v5: additional register init
v6: rebase
v7: fix gb_addr_config for KV/KB
v8: drop wip KV bits for now, add missing config reg
v9: fix cu count on Bonaire
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

register BAR is now at PCI BAR 5.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

New asics support non-privileged IBs.  This allows us
to skip IB checking in the driver since the hardware
will check the command buffers for us.  When using
non-privileged IBs, if the CP encounters an illegal
register in the command stream, it will halt and generate
an interrupt.  The CP needs to be reset to continue.  For now
just do a full GPU reset when this happens.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Mac laptops with multiple GPUs apparently use the gmux
driver for backlight control.  Don't register a radeon
backlight interface.  We may need to add other pci ids
for other hybrid mac laptops.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=65377Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

- remove adding 2 to checksum, this is incorrect.

This was incorrectly introduced in:
92db7f6c
http://lists.freedesktop.org/archives/dri-devel/2011-December/017717.html
However, the off by 2 was due to adding the version twice.
From the examples in the URL above:

[Rafał Miłecki][RV620] fglrx:
0x7454: 00 A8 5E 79     R600_HDMI_VIDEOINFOFRAME_0
0x7458: 00 28 00 10     R600_HDMI_VIDEOINFOFRAME_1
0x745C: 00 48 00 28     R600_HDMI_VIDEOINFOFRAME_2
0x7460: 02 00 00 48     R600_HDMI_VIDEOINFOFRAME_3
===================
(0x82 + 0x2 + 0xD) + 0x1F8 = 0x289
-0x289 = 0x77

However, the payload sum is not 0x1f8, it's 0x1f6.
00 + A8 + 5E + 00 +
00 + 28 + 00 + 10 +
00 + 48 + 00 + 28 +
00 + 48 =
0x1f6

Bits 25:24 of HDMI_VIDEOINFOFRAME_3 are the packet version, not part
of the payload.  So the total would be:
(0x82 + 0x2 + 0xD) + 0x1f6 = 0x287
-0x287 = 0x79

- properly emit the AVI infoframe version.  This was not being
emitted previous which is probably what caused the issue above.

This should fix blank screen when HDMI audio is enabled on
certain monitors.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Cc: Rafał Miłecki <zajec5@gmail.com>

This fixes the kernel side so that the ring should come
up and ring and IB tests should work.  The userspace
UVD drivers will also need big endian fixes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

UVD ring can't use scratch thus it does need writeback buffer to keep
a valid address or radeon_ring_backup will trigger a kernel fault.

It's ok to not unpin the write back buffer on suspend as it leave in
gtt and thus does not need eviction.

v2: Fix the uvd case.

Reported and tracked by Wojtek <wojtask9@wp.pl>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

If a buffer is never bound to a virtual memory pagetable than don't try
to unbind it. Only drawback is that we don't update the pagetable when
unbinding the ib pool buffer which is fine because it only happens at
suspend or module unload/shutdown.

Fixes spurious messages about buffers without VM mappings. E.g.:
radeon 0000:01:00.0: bo ffff88020afac400 don't has a mapping in vm ffff88021ca2b900

Cc: stable@kernel.org
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Merge tag 'drm-intel-fixes-2013-06-11' of git://people.freedesktop.org/~danvet/drm-intel into drm-fixes

Daniel writes:
Just tiny regression fixes here:
- Two fixes to fix sdvo hotplug which broke in the hpd storm detection
  work.
- One fix to patch-up the sdvo lvds regression fixer from the last pull -
  we need to prefer the vbt mode over edid modes.

* tag 'drm-intel-fixes-2013-06-11' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: prefer VBT modes for SVDO-LVDS over EDID
  drm/i915: Enable hotplug interrupts after querying hw capabilities.
  drm/i915: Fix hotplug interrupt enabling for SDVOC

Patrik writes:
Two fixes for memory leaks split into Cedarview and Poulsbo versions,
and a fix for properly setting the pipe base when using fbdev. It's on
my todo-list to start unifying the chips since they are very similar,
but until then I'd like to split them up in case there are side-effects
on Cedarview that I cannot currently test.

airled: Verified pull from github matches what I expected.
* 'gma500-fixes' of git://github.com/patjak/drm-gma500:
  drm/gma500/cdv: Fix cursor gem obj referencing on cdv
  drm/gma500/psb: Fix cursor gem obj referencing on psb
  drm/gma500/cdv: Unpin framebuffer on crtc disable
  drm/gma500/psb: Unpin framebuffer on crtc disable
  drm/gma500: Add fb gtt offset to fb base

Pull spi fixes from Mark Brown:
 "A few nasty issues, particularly a race with the interrupt controller
  in the xilinx driver, together with a couple of more minor fixes and a
  much needed move of the mailing list away from sourceforge."

* tag 'spi-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: hspi: fixup long delay time
  spi: spi-xilinx: Remove ISR race condition
  spi: topcliff-pch: fix error return code in pch_spi_probe()
  spi: topcliff-pch: Pass correct pointer to free_irq()
  spi: Move mailing list to vger

Merge tag 'stable/for-linus-3.10-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull xen fixes from Konrad Rzeszutek Wilk:
 "Two bug-fixes for regressions:
   - xen/tmem stopped working after a certain combination of
     modprobe/swapon was used
   - cpu online/offlining would trigger WARN_ON."

* tag 'stable/for-linus-3.10-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/tmem: Don't over-write tmem_frontswap_poolid after tmem_frontswap_init set it.
  xen/smp: Fixup NOHZ per cpu data when onlining an offline CPU.

Pull regmap fixes from Mark Brown:
 "The biggest fix here is Lars-Peter's fix for custom locking callbacks
  which is pretty localised but important for those devices that use the
  feature.  Otherwise we've got a couple of fairly small cleanups which
  would have been sent sooner were it not for letting Lars-Peter's patch
  soak for a while"

* tag 'regmap-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: rbtree: Fixed node range check on sync
  regmap: regcache: Fixup locking for custom lock callbacks
  regmap: debugfs: Check return value of regmap_write()

Pull crypto fixes from Herbert Xu:
 "This fixes a build problem in sahara and temporarily disables two new
  optimisations because of performance regressions until a permanent fix
  is ready"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: sahara - fix building as module
  crypto: blowfish - disable AVX2 implementation
  crypto: twofish - disable AVX2 implementation

Commit 10a7a077 ("xen: tmem: enable Xen
tmem shim to be built/loaded as a module") allows the tmem module
to be loaded any time. For this work the frontswap API had to
be able to asynchronously to call tmem_frontswap_init before
or after the swap image had been set. That was added in git
commit 905cd0e1
("mm: frontswap: lazy initialization to allow tmem backends to build/run as modules").

Which means we could do this (The common case):

 modprobe tmem		[so calls frontswap_register_ops, no ->init]
			 modifies tmem_frontswap_poolid = -1
 swapon /dev/xvda1	[__frontswap_init, calls -> init, tmem_frontswap_poolid is
			 < 0 so tmem hypercall done]

Or the failing one:

 swapon /dev/xvda1	[calls __frontswap_init, sets the need_init bitmap]
 modprobe tmem		[calls frontswap_register_ops, -->init calls, finds out
			tmem_frontswap_poolid is 0, does not make a hypercall.
			Later in the module_init, sets tmem_frontswap_poolid=-1]

Which meant that in the failing case we would not call the hypercall
to initialize the pool and never be able to make any frontswap
backend calls.

Moving the frontswap_register_ops after setting the tmem_frontswap_poolid
fixes it.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Bob Liu <bob.liu@oracle.com>