- 26 Jul, 2018 1 commit
-
-
Wang YanQing authored
Commit 24dea047 ("bpf, x32: remove ld_abs/ld_ind") removed the 4 /* Extra space for skb_copy_bits buffer */ from _STACK_SIZE, but it didn't fix the concerned code in emit_prologue and emit_epilogue, and this error will bring very strange kernel runtime errors. This patch fixes it. Fixes: 24dea047 ("bpf, x32: remove ld_abs/ld_ind") Reported-by:
Meelis Roos <mroos@linux.ee> Bisected-by:
Wang YanQing <udknight@gmail.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net>
-
- 25 Jul, 2018 4 commits
-
-
Daniel Borkmann authored
Martin KaFai Lau says: ==================== The series allows the BPF loader to figure out the btf_key_id and btf_value_id from a map's name by using BPF_ANNOTATE_KV_PAIR() similarly as in iproute2 commit f823f36012fb ("bpf: implement btf handling and map annotation"). It also removes the old 'typedef' way which requires two separate typedefs (one for the key and one for the value). By doing this, iproute2 and libbpf have one consistent way to figure out the btf_key_type_id and btf_value_type_id for a map. The first two patches are some prep/cleanup works. The last patch introduces BPF_ANNOTATE_KV_PAIR. v3: - Replace some more *int*_t and u* usages with the equivalent __[su]* in btf.c v2: - Fix the incorrect '&&' check on container_type in bpf_map_find_btf_info(). - Expose the existing static btf_type_by_id() instead of creating a new one. ==================== Signed-off-by: -
Martin KaFai Lau authored
This patch introduces BPF_ANNOTATE_KV_PAIR to signal the bpf loader about the btf key_type and value_type of a bpf map. Please refer to the changes in test_btf_haskv.c for its usage. Both iproute2 and libbpf loader will then have the same convention to find out the map's btf_key_type_id and btf_value_type_id from a map's name. Fixes: 8a138aed ("bpf: btf: Add BTF support to libbpf") Suggested-by:
Martin KaFai Lau <kafai@fb.com> Acked-by:
Yonghong Song <yhs@fb.com> Signed-off-by:
-
Martin KaFai Lau authored
This patch replaces [u]int32_t and [u]int64_t usage with __[su]32 and __[su]64. The same change goes for [u]int16_t and [u]int8_t. Fixes: 8a138aed ("bpf: btf: Add BTF support to libbpf") Signed-off-by:
-
Martin KaFai Lau authored
This patch sync the uapi btf.h to tools/ Fixes: 36fc3c8c bpf: btf: Clean up BTF_INT_BITS() in uapi btf.h Signed-off-by:
-
- 23 Jul, 2018 22 commits
-
-
Martin KaFai Lau authored
This patch ensures the member->offset of a struct is in the correct order (i.e the later member's offset cannot go backward). The current "pahole -J" BTF encoder does not generate something like this. However, checking this can ensure future encoder will not violate this. Fixes: 69b693f0 ("bpf: btf: Introduce BPF Type Format (BTF)") Signed-off-by:
-
David S. Miller authored
Eric Dumazet says: ==================== Juha-Matti Tilli reported that malicious peers could inject tiny packets in out_of_order_queue, forcing very expensive calls to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for every incoming packet. With tcp_rmem[2] default of 6MB, the ooo queue could contain ~7000 nodes. This patch series makes sure we cut cpu cycles enough to render the attack not critical. We might in the future go further, like disconnecting or black-holing proven malicious flows. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
In case skb in out_or_order_queue is the result of multiple skbs coalescing, we would like to get a proper gso_segs counter tracking, so that future tcp_drop() can report an accurate number. I chose to not implement this tracking for skbs in receive queue, since they are not dropped, unless socket is disconnected. Signed-off-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Acked-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
Eric Dumazet authored
In order to be able to give better diagnostics and detect malicious traffic, we need to have better sk->sk_drops tracking. Fixes: 9f5afeae ("tcp: use an RB tree for ooo receive queue") Signed-off-by:
-
Eric Dumazet authored
In case an attacker feeds tiny packets completely out of order, tcp_collapse_ofo_queue() might scan the whole rb-tree, performing expensive copies, but not changing socket memory usage at all. 1) Do not attempt to collapse tiny skbs. 2) Add logic to exit early when too many tiny skbs are detected. We prefer not doing aggressive collapsing (which copies packets) for pathological flows, and revert to tcp_prune_ofo_queue() which will be less expensive. In the future, we might add the possibility of terminating flows that are proven to be malicious. Signed-off-by:
-
Eric Dumazet authored
Right after a TCP flow is created, receiving tiny out of order packets allways hit the condition : if (atomic_read(&sk->sk_rmem_alloc) >= sk->sk_rcvbuf) tcp_clamp_window(sk); tcp_clamp_window() increases sk_rcvbuf to match sk_rmem_alloc (guarded by tcp_rmem[2]) Calling tcp_collapse_ofo_queue() in this case is not useful, and offers a O(N^2) surface attack to malicious peers. Better not attempt anything before full queue capacity is reached, forcing attacker to spend lots of resource and allow us to more easily detect the abuse. Signed-off-by:
-
Eric Dumazet authored
Juha-Matti Tilli reported that malicious peers could inject tiny packets in out_of_order_queue, forcing very expensive calls to tcp_collapse_ofo_queue() and tcp_prune_ofo_queue() for every incoming packet. out_of_order_queue rb-tree can contain thousands of nodes, iterating over all of them is not nice. Before linux-4.9, we would have pruned all packets in ofo_queue in one go, every XXXX packets. XXXX depends on sk_rcvbuf and skbs truesize, but is about 7000 packets with tcp_rmem[2] default of 6 MB. Since we plan to increase tcp_rmem[2] in the future to cope with modern BDP, can not revert to the old behavior, without great pain. Strategy taken in this patch is to purge ~12.5 % of the queue capacity. Fixes: 36a6503f ("tcp: refine tcp_prune_ofo_queue() to not drop all packets") Signed-off-by:
Juha-Matti Tilli <juha-matti.tilli@iki.fi> Acked-by:
-
Paolo Abeni authored
The skb hash for locally generated ip[v6] fragments belonging to the same datagram can vary in several circumstances: * for connected UDP[v6] sockets, the first fragment get its hash via set_owner_w()/skb_set_hash_from_sk() * for unconnected IPv6 UDPv6 sockets, the first fragment can get its hash via ip6_make_flowlabel()/skb_get_hash_flowi6(), if auto_flowlabel is enabled For the following frags the hash is usually computed via skb_get_hash(). The above can cause OoO for unconnected IPv6 UDPv6 socket: in that scenario the egress tx queue can be selected on a per packet basis via the skb hash. It may also fool flow-oriented schedulers to place fragments belonging to the same datagram in different flows. Fix the issue by copying the skb hash from the head frag into the others at fragmentation time. Before this commit: perf probe -a "dev_queue_xmit skb skb->hash skb->l4_hash:b1@0/8 skb->sw_hash:b1@1/8" netperf -H $IPV4 -t UDP_STREAM -l 5 -- -m 2000 -n & perf record -e probe:dev_queue_xmit -e probe:skb_set_owner_w -a sleep 0.1 perf script probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=3713014309 l4_hash=1 sw_hash=0 probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=0 l4_hash=0 sw_hash=0 After this commit: probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0 probe:dev_queue_xmit: (ffffffff8c6b1b20) hash=2171763177 l4_hash=1 sw_hash=0 Fixes: b73c3d0e ("net: Save TX flow hash in sock and set in skbuf on xmit") Fixes: 67800f9b ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Reviewed-by:
-
Wei Wang authored
In the code path where only rcu read lock is held, e.g. in the route lookup code path, it is not safe to directly call fib6_info_hold() because the fib6_info may already have been deleted but still exists in the rcu grace period. Holding reference to it could cause double free and crash the kernel. This patch adds a new function fib6_info_hold_safe() and replace fib6_info_hold() in all necessary places. Syzbot reported 3 crash traces because of this. One of them is: 8021q: adding VLAN 0 to HW filter on device team0 IPv6: ADDRCONF(NETDEV_CHANGE): team0: link becomes ready dst_release: dst:(____ptrval____) refcnt:-1 dst_release: dst:(____ptrval____) refcnt:-2 WARNING: CPU: 1 PID: 4845 at include/net/dst.h:239 dst_hold include/net/dst.h:239 [inline] WARNING: CPU: 1 PID: 4845 at include/net/dst.h:239 ip6_setup_cork+0xd66/0x1830 net/ipv6/ip6_output.c:1204 dst_release: dst:(____ptrval____) refcnt:-1 Kernel panic - not syncing: panic_on_warn set ... CPU: 1 PID: 4845 Comm: syz-executor493 Not tainted 4.18.0-rc3+ #10 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113 panic+0x238/0x4e7 kernel/panic.c:184 dst_release: dst:(____ptrval____) refcnt:-2 dst_release: dst:(____ptrval____) refcnt:-3 __warn.cold.8+0x163/0x1ba kernel/panic.c:536 dst_release: dst:(____ptrval____) refcnt:-4 report_bug+0x252/0x2d0 lib/bug.c:186 fixup_bug arch/x86/kernel/traps.c:178 [inline] do_error_trap+0x1fc/0x4d0 arch/x86/kernel/traps.c:296 dst_release: dst:(____ptrval____) refcnt:-5 do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:316 invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:992 RIP: 0010:dst_hold include/net/dst.h:239 [inline] RIP: 0010:ip6_setup_cork+0xd66/0x1830 net/ipv6/ip6_output.c:1204 Code: c1 ed 03 89 9d 18 ff ff ff 48 b8 00 00 00 00 00 fc ff df 41 c6 44 05 00 f8 e9 2d 01 00 00 4c 8b a5 c8 fe ff ff e8 1a f6 e6 fa <0f> 0b e9 6a fc ff ff e8 0e f6 e6 fa 48 8b 85 d0 fe ff ff 48 8d 78 RSP: 0018:ffff8801a8fcf178 EFLAGS: 00010293 RAX: ffff8801a8eba5c0 RBX: 0000000000000000 RCX: ffffffff869511e6 RDX: 0000000000000000 RSI: ffffffff869515b6 RDI: 0000000000000005 RBP: ffff8801a8fcf2c8 R08: ffff8801a8eba5c0 R09: ffffed0035ac8338 R10: ffffed0035ac8338 R11: ffff8801ad6419c3 R12: ffff8801a8fcf720 R13: ffff8801a8fcf6a0 R14: ffff8801ad6419c0 R15: ffff8801ad641980 ip6_make_skb+0x2c8/0x600 net/ipv6/ip6_output.c:1768 udpv6_sendmsg+0x2c90/0x35f0 net/ipv6/udp.c:1376 inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798 sock_sendmsg_nosec net/socket.c:641 [inline] sock_sendmsg+0xd5/0x120 net/socket.c:651 ___sys_sendmsg+0x51d/0x930 net/socket.c:2125 __sys_sendmmsg+0x240/0x6f0 net/socket.c:2220 __do_sys_sendmmsg net/socket.c:2249 [inline] __se_sys_sendmmsg net/socket.c:2246 [inline] __x64_sys_sendmmsg+0x9d/0x100 net/socket.c:2246 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x446ba9 Code: e8 cc bb 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fb39a469da8 EFLAGS: 00000246 ORIG_RAX: 0000000000000133 RAX: ffffffffffffffda RBX: 00000000006dcc54 RCX: 0000000000446ba9 RDX: 00000000000000b8 RSI: 0000000020001b00 RDI: 0000000000000003 RBP: 00000000006dcc50 R08: 00007fb39a46a700 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 45c828efc7a64843 R13: e6eeb815b9d8a477 R14: 5068caf6f713c6fc R15: 0000000000000001 Dumping ftrace buffer: (ftrace buffer empty) Kernel Offset: disabled Rebooting in 86400 seconds.. Fixes: 93531c67 ("net/ipv6: separate handling of FIB entries from dst based routes") Reported-by: syzbot+902e2a1bcd4f7808cef5@syzkaller.appspotmail.com Reported-by: syzbot+8ae62d67f647abeeceb9@syzkaller.appspotmail.com Reported-by: syzbot+3f08feb14086930677d0@syzkaller.appspotmail.com Signed-off-by:
Wei Wang <weiwan@google.com> Acked-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-4.18-20180723' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2018-07-23 this is a pull request of 12 patches for net/master. The patch by Stephane Grosjean for the peak_canfd CAN driver fixes a problem with older firmware. The next patch is by Roman Fietze and fixes the setup of the CCCR register in the m_can driver. Nicholas Mc Guire's patch for the mpc5xxx_can driver adds missing error checking. The two patches by Faiz Abbas fix the runtime resume and clean up the probe function in the m_can driver. The last 7 patches by Anssi Hannula fix several problem in the xilinx_can driver. ==================== Signed-off-by:
-
Anssi Hannula authored
There are several issues with the suspend/resume handling code of the driver: - The device is attached and detached in the runtime_suspend() and runtime_resume() callbacks if the interface is running. However, during xcan_chip_start() the interface is considered running, causing the resume handler to incorrectly call netif_start_queue() at the beginning of xcan_chip_start(), and on xcan_chip_start() error return the suspend handler detaches the device leaving the user unable to bring-up the device anymore. - The device is not brought properly up on system resume. A reset is done and the code tries to determine the bus state after that. However, after reset the device is always in Configuration mode (down), so the state checking code does not make sense and communication will also not work. - The suspend callback tries to set the device to sleep mode (low-power mode which monitors the bus and brings the device back to normal mode on activity), but then immediately disables the clocks (possibly before the device reaches the sleep mode), which does not make sense to me. If a clean shutdown is wanted before disabling clocks, we can just bring it down completely instead of only sleep mode. Reorganize the PM code so that only the clock logic remains in the runtime PM callbacks and the system PM callbacks contain the device bring-up/down logic. This makes calling the runtime PM callbacks during e.g. xcan_chip_start() safe. The system PM callbacks now simply call common code to start/stop the HW if the interface was running, replacing the broken code from before. xcan_chip_stop() is updated to use the common reset code so that it will wait for the reset to complete. Reset also disables all interrupts so do not do that separately. Also, the device_may_wakeup() checks are removed as the driver does not have wakeup support. Tested on Zynq-7000 integrated CAN. Signed-off-by:
Anssi Hannula <anssi.hannula@bitwise.fi> Cc: Michal Simek <michal.simek@xilinx.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Anssi Hannula authored
xcan_interrupt() clears ERROR|RXOFLV|BSOFF|ARBLST interrupts if any of them is asserted. This does not take into account that some of them could have been asserted between interrupt status read and interrupt clear, therefore clearing them without handling them. Fix the code to only clear those interrupts that it knows are asserted and therefore going to be processed in xcan_err_interrupt(). Fixes: b1201e44 ("can: xilinx CAN controller support") Signed-off-by:
-
Anssi Hannula authored
RX overflow interrupt (RXOFLW) is disabled even though xcan_interrupt() processes it. This means that an RX overflow interrupt will only be processed when another interrupt gets asserted (e.g. for RX/TX). Fix that by enabling the RXOFLW interrupt. Fixes: b1201e44 ("can: xilinx CAN controller support") Signed-off-by:
-
Anssi Hannula authored
The xilinx_can driver assumes that the TXOK interrupt only clears after it has been acknowledged as many times as there have been successfully sent frames. However, the documentation does not mention such behavior, instead saying just that the interrupt is cleared when the clear bit is set. Similarly, testing seems to also suggest that it is immediately cleared regardless of the amount of frames having been sent. Performing some heavy TX load and then going back to idle has the tx_head drifting further away from tx_tail over time, steadily reducing the amount of frames the driver keeps in the TX FIFO (but not to zero, as the TXOK interrupt always frees up space for 1 frame from the driver's perspective, so frames continue to be sent) and delaying the local echo frames. The TX FIFO tracking is also otherwise buggy as it does not account for TX FIFO being cleared after software resets, causing BUG!, TX FIFO full when queue awake! messages to be output. There does not seem to be any way to accurately track the state of the TX FIFO for local echo support while using the full TX FIFO. The Zynq version of the HW (but not the soft-AXI version) has watermark programming support and with it an additional TX-FIFO-empty interrupt bit. Modify the driver to only put 1 frame into TX FIFO at a time on soft-AXI and 2 frames at a time on Zynq. On Zynq the TXFEMP interrupt bit is used to detect whether 1 or 2 frames have been sent at interrupt processing time. Tested with the integrated CAN on Zynq-7000 SoC. The 1-frame-FIFO mode was also tested. An alternative way to solve this would be to drop local echo support but keep using the full TX FIFO. v2: Add FIFO space check before TX queue wake with locking to synchronize with queue stop. This avoids waking the queue when xmit() had just filled it. v3: Keep local echo support and reduce the amount of frames in FIFO instead as suggested by Marc Kleine-Budde. Fixes: b1201e44 ("can: xilinx CAN controller support") Signed-off-by:
-
Anssi Hannula authored
The xilinx_can driver contains no mechanism for propagating recovery from CAN_STATE_ERROR_WARNING and CAN_STATE_ERROR_PASSIVE. Add such a mechanism by factoring the handling of XCAN_STATE_ERROR_PASSIVE and XCAN_STATE_ERROR_WARNING out of xcan_err_interrupt and checking for recovery after RX and TX if the interface is in one of those states. Tested with the integrated CAN on Zynq-7000 SoC. Fixes: b1201e44 ("can: xilinx CAN controller support") Signed-off-by:
-
Anssi Hannula authored
If the device gets into a state where RXNEMP (RX FIFO not empty) interrupt is asserted without RXOK (new frame received successfully) interrupt being asserted, xcan_rx_poll() will continue to try to clear RXNEMP without actually reading frames from RX FIFO. If the RX FIFO is not empty, the interrupt will not be cleared and napi_schedule() will just be called again. This situation can occur when: (a) xcan_rx() returns without reading RX FIFO due to an error condition. The code tries to clear both RXOK and RXNEMP but RXNEMP will not clear due to a frame still being in the FIFO. The frame will never be read from the FIFO as RXOK is no longer set. (b) A frame is received between xcan_rx_poll() reading interrupt status and clearing RXOK. RXOK will be cleared, but RXNEMP will again remain set as the new message is still in the FIFO. I'm able to trigger case (b) by flooding the bus with frames under load. There does not seem to be any benefit in using both RXNEMP and RXOK in the way the driver does, and the polling example in the reference manual (UG585 v1.10 18.3.7 Read Messages from RxFIFO) also says that either RXOK or RXNEMP can be used for detecting incoming messages. Fix the issue and simplify the RX processing by only using RXNEMP without RXOK. Tested with the integrated CAN on Zynq-7000 SoC. Fixes: b1201e44 ("can: xilinx CAN controller support") Signed-off-by:
-
Anssi Hannula authored
The xilinx_can driver performs a software reset when an RX overrun is detected. This causes the device to enter Configuration mode where no messages are received or transmitted. The documentation does not mention any need to perform a reset on an RX overrun, and testing by inducing an RX overflow also indicated that the device continues to work just fine without a reset. Remove the software reset. Tested with the integrated CAN on Zynq-7000 SoC. Fixes: b1201e44 ("can: xilinx CAN controller support") Signed-off-by:
-
Faiz Abbas authored
MCAN message ram should only be accessed once clocks are enabled. Therefore, move the call to parse/init the message ram to after clocks are enabled. Signed-off-by:
Faiz Abbas <faiz_abbas@ti.com> Signed-off-by:
-
Faiz Abbas authored
pm_runtime_get_sync() returns a 1 if the state of the device is already 'active'. This is not a failure case and should return a success. Therefore fix error handling for pm_runtime_get_sync() call such that it returns success when the value is 1. Also cleanup the TODO for using runtime PM for sleep mode as that is implemented. Signed-off-by:
-
Nicholas Mc Guire authored
of_iomap() can return NULL so that return needs to be checked and NULL treated as failure. While at it also take care of the missing of_node_put() in the error path. Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Fixes: commit afa17a50 ("net/can: add driver for mscan family & mpc52xx_mscan") Signed-off-by:
-
Roman Fietze authored
Inside m_can_chip_config(), when setting up the new value of the CCCR, the CCCR_NISO bit is not cleared like the others, CCCR_TEST, CCCR_MON, CCCR_BRSE and CCCR_FDOE, before checking the can.ctrlmode bits for CAN_CTRLMODE_FD_NON_ISO. This way once the controller was configured for CAN_CTRLMODE_FD_NON_ISO, this mode could never be cleared again. This fix is only relevant for controllers with version 3.1.x or 3.2.x. Older versions do not support NISO. Signed-off-by:
Roman Fietze <roman.fietze@telemotive.de> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
-
Stephane Grosjean authored
The DMA logic in firmwares < v3.3.0 embedded in the PCAN-PCIe FD cards family is not capable of handling a mix of 32-bit and 64-bit logical addresses. If the board is equipped with 2 or 4 CAN ports, then such a situation might lead to a PCIe Bus Error "Malformed TLP" packet as well as "irq xx: nobody cared" issue. This patch adds a workaround that requests only 32-bit DMA addresses when these might be allocated outside of the 4 GB area. This issue has been fixed in firmware v3.3.0 and next. Signed-off-by:
Stephane Grosjean <s.grosjean@peak-system.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
-
- 22 Jul, 2018 12 commits
-
-
Randy Dunlap authored
Prevent drivers from building on PPC32 if they use isa_bus_to_virt(), isa_virt_to_bus(), or isa_page_to_bus(), which are not available and thus cause build errors. ../drivers/net/ethernet/3com/3c515.c: In function 'corkscrew_open': ../drivers/net/ethernet/3com/3c515.c:824:9: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration] ../drivers/net/ethernet/amd/lance.c: In function 'lance_rx': ../drivers/net/ethernet/amd/lance.c:1203:23: error: implicit declaration of function 'isa_bus_to_virt'; did you mean 'bus_to_virt'? [-Werror=implicit-function-declaration] ../drivers/net/ethernet/amd/ni65.c: In function 'ni65_init_lance': ../drivers/net/ethernet/amd/ni65.c:585:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration] ../drivers/net/ethernet/cirrus/cs89x0.c: In function 'net_open': ../drivers/net/ethernet/cirrus/cs89x0.c:897:20: error: implicit declaration of function 'isa_virt_to_bus'; did you mean 'virt_to_bus'? [-Werror=implicit-function-declaration] Signed-off-by:
Randy Dunlap <rdunlap@infradead.org> Suggested-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
John Hurley authored
Previously only the neighbour state was checked to decide if an offloaded entry should be removed. However, there can be situations when the entry is dead but still marked as valid. This can lead to dead entries not being removed from fw tables or even incorrect data being added. Check the entry dead bit before deciding if it should be added to or removed from fw neighbour tables. Fixes: 8e6a9046 ("nfp: flower vxlan neighbour offload") Signed-off-by:
John Hurley <john.hurley@netronome.com> Reviewed-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
-
David S. Miller authored
Roopa Prabhu says: ==================== vxlan: fix default fdb entry user-space notify ordering/race Problem: In vxlan_newlink, a default fdb entry is added before register_netdev. The default fdb creation function notifies user-space of the fdb entry on the vxlan device which user-space does not know about yet. (RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex). This series fixes the user-space netlink notification ordering issue with the following changes: - decouple fdb notify from fdb create. - Move fdb notify after register_netdev. - modify rtnl_configure_link to allow configuring a link early. - Call rtnl_configure_link in vxlan newlink handler to notify userspace about the newlink before fdb notify and hence avoiding the user-space race. ==================== Fixes: afbd8bae ("vxlan: add implicit fdb entry for default destination") Signed-off-by:
Roopa Prabhu <roopa@cumulusnetworks.com>
-
Roopa Prabhu authored
Problem: In vxlan_newlink, a default fdb entry is added before register_netdev. The default fdb creation function also notifies user-space of the fdb entry on the vxlan device which user-space does not know about yet. (RTM_NEWNEIGH goes before RTM_NEWLINK for the same ifindex). This patch fixes the user-space netlink notification ordering issue with the following changes: - decouple fdb notify from fdb create. - Move fdb notify after register_netdev. - Call rtnl_configure_link in vxlan newlink handler to notify userspace about the newlink before fdb notify and hence avoiding the user-space race. Fixes: afbd8bae ("vxlan: add implicit fdb entry for default destination") Signed-off-by:
-
Roopa Prabhu authored
Add a new option do_notify to vxlan_fdb_destroy to make sending netlink notify optional. Used by a later patch. Signed-off-by:
-
Roopa Prabhu authored
- Add new vxlan_fdb_alloc helper - rename existing vxlan_fdb_create into vxlan_fdb_update: because it really creates or updates an existing fdb entry - move new fdb creation into a separate vxlan_fdb_create Main motivation for this change is to introduce the ability to decouple vxlan fdb creation and notify, used in a later patch. Signed-off-by: -
Roopa Prabhu authored
rtnl_configure_link sets dev->rtnl_link_state to RTNL_LINK_INITIALIZED and unconditionally calls __dev_notify_flags to notify user-space of dev flags. current call sequence for rtnl_configure_link rtnetlink_newlink rtnl_link_ops->newlink rtnl_configure_link (unconditionally notifies userspace of default and new dev flags) If a newlink handler wants to call rtnl_configure_link early, we will end up with duplicate notifications to user-space. This patch fixes rtnl_configure_link to check rtnl_link_state and call __dev_notify_flags with gchanges = 0 if already RTNL_LINK_INITIALIZED. Later in the series, this patch will help the following sequence where a driver implementing newlink can call rtnl_configure_link to initialize the link early. makes the following call sequence work: rtnetlink_newlink rtnl_link_ops->newlink (vxlan) -> rtnl_configure_link (initializes link and notifies user-space of default dev flags) rtnl_configure_link (updates dev flags if requested by user ifm and notifies user-space of new dev flags) Signed-off-by: -
Florian Westphal authored
Got crash report with following backtrace: BUG: unable to handle kernel paging request at ffff8801869daffe RIP: 0010:[<ffffffff816429c4>] [<ffffffff816429c4>] ip6_finish_output2+0x394/0x4c0 RSP: 0018:ffff880186c83a98 EFLAGS: 00010283 RAX: ffff8801869db00e ... [<ffffffff81644cdc>] ip6_finish_output+0x8c/0xf0 [<ffffffff81644d97>] ip6_output+0x57/0x100 [<ffffffff81643dc9>] ip6_forward+0x4b9/0x840 [<ffffffff81645566>] ip6_rcv_finish+0x66/0xc0 [<ffffffff81645db9>] ipv6_rcv+0x319/0x530 [<ffffffff815892ac>] netif_receive_skb+0x1c/0x70 [<ffffffffc0060bec>] atl1c_clean+0x1ec/0x310 [atl1c] ... The bad access is in neigh_hh_output(), at skb->data - 16 (HH_DATA_MOD). atl1c driver provided skb with no headroom, so 14 bytes (ethernet header) got pulled, but then 16 are copied. Reserve NET_SKB_PAD bytes headroom, like netdev_alloc_skb(). Compile tested only; I lack hardware. Fixes: 7b701764 ("atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring") Signed-off-by:
Florian Westphal <fw@strlen.de> Reviewed-by:
-
Hangbin Liu authored
There are two scenarios that we will restore deleted records. The first is when device down and up(or unmap/remap). In this scenario the new filter mode is same with previous one. Because we get it from in_dev->mc_list and we do not touch it during device down and up. The other scenario is when a new socket join a group which was just delete and not finish sending status reports. In this scenario, we should use the current filter mode instead of restore old one. Here are 4 cases in total. old_socket new_socket before_fix after_fix IN(A) IN(A) ALLOW(A) ALLOW(A) IN(A) EX( ) TO_IN( ) TO_EX( ) EX( ) IN(A) TO_EX( ) ALLOW(A) EX( ) EX( ) TO_EX( ) TO_EX( ) Fixes: 24803f38 (igmp: do not remove igmp souce list info when set link down) Fixes: 1666d49e (mld: do not remove mld souce list info when set link down) Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Signed-off-by:
-
Uwe Kleine-König authored
free_irq() waits until all handlers for this IRQ have completed. As the relevant handler (mv88e6xxx_g1_irq_thread_fn()) takes the chip's reg_lock it might never return if the thread calling free_irq() holds this lock. For the same reason kthread_cancel_delayed_work_sync() in the polling case must not hold this lock. Also first free the irq (or stop the worker respectively) such that mv88e6xxx_g1_irq_thread_work() isn't called any more before the irq mappings are dropped in mv88e6xxx_g1_irq_free_common() to prevent the worker thread to call handle_nested_irq(0) which results in a NULL-pointer exception. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Eric Dumazet authored
syzbot caught a NULL deref [1], caused by skb_segment() skb_segment() has many "goto err;" that assume the @err variable contains -ENOMEM. A successful call to __skb_linearize() should not clear @err, otherwise a subsequent memory allocation error could return NULL. While we are at it, we might use -EINVAL instead of -ENOMEM when MAX_SKB_FRAGS limit is reached. [1] kasan: CONFIG_KASAN_INLINE enabled kasan: GPF could be caused by NULL-ptr deref or user memory access general protection fault: 0000 [#1] SMP KASAN CPU: 0 PID: 13285 Comm: syz-executor3 Not tainted 4.18.0-rc4+ #146 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:tcp_gso_segment+0x3dc/0x1780 net/ipv4/tcp_offload.c:106 Code: f0 ff ff 0f 87 1c fd ff ff e8 00 88 0b fb 48 8b 75 d0 48 b9 00 00 00 00 00 fc ff df 48 8d be 90 00 00 00 48 89 f8 48 c1 e8 03 <0f> b6 14 08 48 8d 86 94 00 00 00 48 89 c6 83 e0 07 48 c1 ee 03 0f RSP: 0018:ffff88019b7fd060 EFLAGS: 00010206 RAX: 0000000000000012 RBX: 0000000000000020 RCX: dffffc0000000000 RDX: 0000000000040000 RSI: 0000000000000000 RDI: 0000000000000090 RBP: ffff88019b7fd0f0 R08: ffff88019510e0c0 R09: ffffed003b5c46d6 R10: ffffed003b5c46d6 R11: ffff8801dae236b3 R12: 0000000000000001 R13: ffff8801d6c581f4 R14: 0000000000000000 R15: ffff8801d6c58128 FS: 00007fcae64d6700(0000) GS:ffff8801dae00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000004e8664 CR3: 00000001b669b000 CR4: 00000000001406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: tcp4_gso_segment+0x1c3/0x440 net/ipv4/tcp_offload.c:54 inet_gso_segment+0x64e/0x12d0 net/ipv4/af_inet.c:1342 inet_gso_segment+0x64e/0x12d0 net/ipv4/af_inet.c:1342 skb_mac_gso_segment+0x3b5/0x740 net/core/dev.c:2792 __skb_gso_segment+0x3c3/0x880 net/core/dev.c:2865 skb_gso_segment include/linux/netdevice.h:4099 [inline] validate_xmit_skb+0x640/0xf30 net/core/dev.c:3104 __dev_queue_xmit+0xc14/0x3910 net/core/dev.c:3561 dev_queue_xmit+0x17/0x20 net/core/dev.c:3602 neigh_hh_output include/net/neighbour.h:473 [inline] neigh_output include/net/neighbour.h:481 [inline] ip_finish_output2+0x1063/0x1860 net/ipv4/ip_output.c:229 ip_finish_output+0x841/0xfa0 net/ipv4/ip_output.c:317 NF_HOOK_COND include/linux/netfilter.h:276 [inline] ip_output+0x223/0x880 net/ipv4/ip_output.c:405 dst_output include/net/dst.h:444 [inline] ip_local_out+0xc5/0x1b0 net/ipv4/ip_output.c:124 iptunnel_xmit+0x567/0x850 net/ipv4/ip_tunnel_core.c:91 ip_tunnel_xmit+0x1598/0x3af1 net/ipv4/ip_tunnel.c:778 ipip_tunnel_xmit+0x264/0x2c0 net/ipv4/ipip.c:308 __netdev_start_xmit include/linux/netdevice.h:4148 [inline] netdev_start_xmit include/linux/netdevice.h:4157 [inline] xmit_one net/core/dev.c:3034 [inline] dev_hard_start_xmit+0x26c/0xc30 net/core/dev.c:3050 __dev_queue_xmit+0x29ef/0x3910 net/core/dev.c:3569 dev_queue_xmit+0x17/0x20 net/core/dev.c:3602 neigh_direct_output+0x15/0x20 net/core/neighbour.c:1403 neigh_output include/net/neighbour.h:483 [inline] ip_finish_output2+0xa67/0x1860 net/ipv4/ip_output.c:229 ip_finish_output+0x841/0xfa0 net/ipv4/ip_output.c:317 NF_HOOK_COND include/linux/netfilter.h:276 [inline] ip_output+0x223/0x880 net/ipv4/ip_output.c:405 dst_output include/net/dst.h:444 [inline] ip_local_out+0xc5/0x1b0 net/ipv4/ip_output.c:124 ip_queue_xmit+0x9df/0x1f80 net/ipv4/ip_output.c:504 tcp_transmit_skb+0x1bf9/0x3f10 net/ipv4/tcp_output.c:1168 tcp_write_xmit+0x1641/0x5c20 net/ipv4/tcp_output.c:2363 __tcp_push_pending_frames+0xb2/0x290 net/ipv4/tcp_output.c:2536 tcp_push+0x638/0x8c0 net/ipv4/tcp.c:735 tcp_sendmsg_locked+0x2ec5/0x3f00 net/ipv4/tcp.c:1410 tcp_sendmsg+0x2f/0x50 net/ipv4/tcp.c:1447 inet_sendmsg+0x1a1/0x690 net/ipv4/af_inet.c:798 sock_sendmsg_nosec net/socket.c:641 [inline] sock_sendmsg+0xd5/0x120 net/socket.c:651 __sys_sendto+0x3d7/0x670 net/socket.c:1797 __do_sys_sendto net/socket.c:1809 [inline] __se_sys_sendto net/socket.c:1805 [inline] __x64_sys_sendto+0xe1/0x1a0 net/socket.c:1805 do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x455ab9 Code: 1d ba fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb b9 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fcae64d5c68 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007fcae64d66d4 RCX: 0000000000455ab9 RDX: 0000000000000001 RSI: 0000000020000200 RDI: 0000000000000013 RBP: 000000000072bea0 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000014 R13: 00000000004c1145 R14: 00000000004d1818 R15: 0000000000000006 Modules linked in: Dumping ftrace buffer: (ftrace buffer empty) Fixes: ddff00d4 ("net: Move skb_has_shared_frag check out of GRE code and into segmentation") Signed-off-by:
syzbot <syzkaller@googlegroups.com> Acked-by:
Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by:
-
David Ahern authored
Example setup: host: ip -6 addr add dev eth1 2001:db8:104::4 where eth1 is enslaved to a VRF switch: ip -6 ro add 2001:db8:104::4/128 dev br1 where br1 only has an LLA ping6 2001:db8:104::4 ssh 2001:db8:104::4 (NOTE: UDP works fine if the PKTINFO has the address set to the global address and ifindex is set to the index of eth1 with a destination an LLA). For ICMP, icmp6_iif needs to be updated to check if skb->dev is an L3 master. If it is then return the ifindex from rt6i_idev similar to what is done for loopback. For TCP, restore the original tcp_v6_iif definition which is needed in most places and add a new tcp_v6_iif_l3_slave that considers the l3_slave variability. This latter check is only needed for socket lookups. Fixes: 9ff74384 ("net: vrf: Handle ipv6 multicast and link-local addresses") Signed-off-by:
-
- 21 Jul, 2018 1 commit
-
-
YueHaibing authored
Fix following warning: net/ipv4/bpfilter/sockopt.c:28:5: error: symbol 'bpfilter_ip_set_sockopt' redeclared with different type net/ipv4/bpfilter/sockopt.c:34:5: error: symbol 'bpfilter_ip_get_sockopt' redeclared with different type Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Acked-by:
-
