Merge tag 'ux500-devicetree-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt

From Linus Walleij:
Ux500 device tree patches for v3.14, take 2
- Delete some unused U8540 UART platform data.
- MMC/SD-fixes from Ulf Hansson so everything works with
  the device tree again.

* tag 'ux500-devicetree-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: regulators: Remove dead code for SD-card regulator
  ARM: ux500: Configure regulator for I/O voltage for SD-card slot
  ARM: ux500: Refactor common DT configs for sdi[n] devices
  ARM: ux500: delete U8540 UART auxdata
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-dt-fixes-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

From Simon Horman:
Renesas ARM Based SoC DT Fixes for v3.14

Revert the addition of SSI clocks to DT for the
r8a7790 (R-Car H2) and r8a7791 (R-Car M2) SoCs.

Unfortunately these patches prevent booting the
r8a7790-based Lager board and r8a7791-based Koelsch board
to the point where a serial output is available.

A solution to this problem is being sought but has not
yet been finalised so in the mean time revert the changes.

* tag 'renesas-dt-fixes-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  Revert "ARM: shmobile: r8a7791: Add SSI clocks in device tree"
  Revert "ARM: shmobile: r8a7790: Add SSI clocks in device tree"
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

From Kukjin Kim:
Samsung DT 3rd updates for v3.14
- add exynos4412-tiny4412 board dt for FriendlyARM's TINY4412
  board including initial support UART, SD card and LEDs
- add exynos5420-arndale-octa board dt for Arndale Octa board

* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: add support for EXYNOS4412 based TINY4412 board
  ARM: dts: Add initial support for Arndale Octa board
Signed-off-by: Olof Johansson <olof@lixom.net>

Add a minimal board dts file for EXYNOS4412 based FriendlyARM's
TINY4412 board. This patch including support peripherals like
UART, SD card on SDMMC2 port and GPIO connected LEDs.
Signed-off-by: Alex Ling <kasimling@gmail.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Arndale Octa board is based on Exynos5420 SoC. This patch
adds the basic support required for booting it through DT.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Merge tag 'renesas-dt3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

From Simon Horman:
Third Round of Renesas ARM Based SoC DT Updates for v3.14

* r8a7791 (R-Car M2) and r8a7790 (R-Car H2) SoCSs
  - Add SSI, QSPI and MSIOF  clocks in device tree

r8a7791 (R-Car M2) based Koelsch and r8a7790 (R-Car H2) based Lager boards
  - Remove reference DTS
  - Specify external clock frequency in DT
  - Sync non-reference DTS with referene DTS
  - Add clocks to DTS

* r8a7740 (R-Mobile A1) based Armadillo board
  - Add gpio-keys device
  - Add PWM backlight enable GPIO
  - Add PWM backlight power supply

* r8a73a0 (SH-Mobile AG5), r8a7740 (R-Mobile A1) and
  r8a73a4 (SH-Mobile APE6) SoCs
  - Specify PFC interrupts in DT

* tag 'renesas-dt3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (72 commits)
  ARM: shmobile: r8a7791: Add SSI clocks in device tree
  ARM: shmobile: r8a7790: Add SSI clocks in device tree
  ARM: shmobile: r8a7791: Add QSPI module clock in device tree
  ARM: shmobile: r8a7790: Add QSPI module clock in device tree
  ARM: shmobile: r8a7791: Add MSIOF clocks in device tree
  ARM: shmobile: r8a7790: Add MSIOF clocks in device tree
  ARM: shmobile: Remove Koelsch reference DTS
  ARM: shmobile: Remove Lager reference DTS
  ARM: shmobile: koelsch: Specify external clock frequency in DT
  ARM: shmobile: lager: Specify external clock frequency in DT
  ARM: shmobile: Sync Koelsch DTS with Koelsch reference DTS
  ARM: shmobile: Sync Lager DTS with Lager reference DTS
  ARM: shmobile: r8a7791: Add clocks
  ARM: shmobile: r8a7790: Reference clocks
  ARM: shmobile: r8a7790: Add clocks
  ARM: shmobile: armadillo: dts: Add gpio-keys device
  ARM: shmobile: sh73a0: Specify PFC interrupts in DT
  ARM: shmobile: r8a7740: Specify PFC interrupts in DT
  ARM: shmobile: r8a73a4: Specify PFC interrupts in DT
  ARM: shmobile: armadillo: dts: Add PWM backlight enable GPIO
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

The BCM2835 SoC contains a DWC2 USB controller. Add this to the DT.

Set up the pin controller to fully enable the USB controller on the
Raspberry Pi. The GPIO setup works because the default output value for
GPIO 6 (LAN_RUN/n_reset) just happens to be 1, which enables the
USB/LAN chip.

Note that you'll need a U-Boot which enables power to the USB controller;
search for U-Boot patch "ARM: rpi_b: power on SDHCI and USB HW modules".
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

From Maxime Ripard:
Allwinner sunXi DT Additions for 3.14

Various DT related patches, but mostly:
  - Support for the Olimex A13-olinuxino-micro
  - Added the needed IP in the A31 for the HS timer support and SMP bringup
  - A10 and A20 RTC

* tag 'sunxi-dt-for-3.14' of https://github.com/mripard/linux:
  ARM: sun6i: dt: Add IP needed to bring up the additional cores
  ARM: dts: sun5i: Add new sun5i-a13-olinuxino-micro board
  ARM: sun6i: Add the reset controller to the DTSI
  ARM: sunxi: dt: add EMAC aliases
  ARM: dts: sun4i/sun7i: add RTC node
Signed-off-by: Olof Johansson <olof@lixom.net>

From Jason Cooper:
mvebu DT changes for v3.14 (incremental #5)

 - mvebu
    - add rtc chip isl12057 node to ReadyNAS boards
    - fix register length in Armada XP pmsu

 - kirkwood
    - sort ocp nodes by address in 6282 dtsi file
    - add 6192 dtsi file
    - add LaPlug board
    - add sata phy node

 - dove
    - add sata phy node

* tag 'mvebu-dt-3.14-5' of git://git.infradead.org/linux-mvebu:
  ARM: Kirkwood: DT board setup for LaPlug
  ARM: Kirkwood: Add 6192 DTSI file
  ARM: mvebu: fix register length for Armada XP PMSU
  ARM: kirkwood: 6282: sort DT nodes by address
  Phy: Add DT nodes on kirkwood and Dove for the SATA PHY
  ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 2120 .dts file
  ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 104 .dts file
  ARM: mvebu: Enable ISL12057 RTC chip in ReadyNAS 102 .dts file
Signed-off-by: Olof Johansson <olof@lixom.net>

* qcom/dt:
  ARM: dts: MSM8974: Add MMIO architected timer node
  ARM: dts: MSM8974: Add restart node
  ARM: msm: Simplify ARCH_MSM_DT config
  ARM: msm: Add support for MSM8974 SoC
  ARM: msm: trout: fix uninit var warning
Signed-off-by: Olof Johansson <olof@lixom.net>

Add the mmio architected timer node.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add the restart node so we can reboot the device.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

This doesn't need to be a def_bool y. Instead we can have every
DT supported platform select ARCH_MSM_DT and we achieve the same
thing with less chance of conflicts.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add support for the Snapdragon 800 MSM8974 SoC, used on the Dragonboard
and others. Board support added in separate patch.
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
[olof: split off SoC support in separate patch]
Signed-off-by: Olof Johansson <olof@lixom.net>

Fix the following warning when !CONFIG_MMC:

arch/arm/mach-msm/board-trout.c: In function 'trout_init':
arch/arm/mach-msm/board-trout.c:67:6: warning: unused variable 'rc' [-Wunused-variable]
  int rc;
      ^

Also, while we're here, rework explicit printk(KERN_CRIT..) to use
pr_crit.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-dt2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

From Simon Horman:
Second Round of Renesas ARM Based SoC DT Updates for v3.13

* r8a7791 (R-Car M2) based Koelsch board
- Add GPIO keys

* sh73a0 (SH-Mobile AG5) based kzm9g board
  - Add FSI support

* tag 'renesas-dt2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: koelsch: dts: Add gpio-keys device
  ARM: shmobile: kzm9g: add FSI support for DTS
  ARM: shmobile: sh73a0: add FSI support via DTSI
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'tegra-for-3.14-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

From Stephen Warren:
ARM: tegra: second set of device tree changes

This branch contains changes to Tegra's device tree that came in after
I sent the previous pull-request/tag tegra-for-3.14-dt. Changes are:

* Set up aliases for RTCs, so that the correct RTC is chosen to
  initialize the system date/time.
* Venice2 pinctrl and regulator configuration.
* Built-in panel enablement for Harmony, Cardhu, Dalmore.
* HDMI enablement for Dalmore.
* USB2 port enablement for Beaver.
* Keyboard and power key enablement for Venice2.

* tag 'tegra-for-3.14-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: Enable power key on Venice2
  ARM: tegra: Enable Venice2 keyboard
  ARM: tegra: enable USB2 on Tegra30 Beaver
  ARM: tegra: modify Tegra30 USB2 default phy_type to UTMI
  ARM: tegra: Enable HDMI support on Dalmore
  ARM: tegra: Enable DSI support on Dalmore
  ARM: tegra: Add Tegra114 gr3d support
  ARM: tegra: Add Tegra114 gr2d support
  ARM: tegra: Add Tegra114 DSI support
  ARM: tegra: Add host1x, DC and HDMI to Tegra114 device tree
  ARM: tegra: Add MIPI calibration DT entries for Tegra114
  ARM: tegra: Enable LVDS on Cardhu
  ARM: tegra: Enable LVDS on Harmony
  ARM: tegra: set up /aliases for RTCs on Venice2
  ARM: tegra: add ams AS3722 device to Venice2 DT
  ARM: tegra: fix missing pincontrol configuration for Venice2
  ARM: tegra: set up /aliases entries for RTCs
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'tegra-for-3.14-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

From Stephen Warren:
ARM: tegra: device tree changes

This branch contains all the changes to Tegra's device tree. The
highlights are:

* Many patches for Tegra124 SoC support, and the Venice2 board which
  uses that SoC.
* Conversion to use more headers providing named constants for pinctrl
  and key codes, which improves readability.
* A few cleanups.

This branch is based on tag tegra-for-3.14-dmas-resets-rework in order
to avoid conflicts with the DT changes required to use the common
bindings for DMAs and resets.

* tag 'tegra-for-3.14-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (24 commits)
  ARM: tegra: Add SPI controller nodes for Tegra124
  ARM: tegra: Fix misconfiguration of pin PH2 on Venice2
  ARM: tegra: fix pinctrl misconfiguration on Venice2
  ARM: tegra: add default pinctrl nodes for Venice2
  ARM: tegra: correct Colibri T20 regulator settings
  ARM: tegra: convert dts files of Tegra30 platforms to use pinctrl defines
  ARM: tegra: convert dts files of Tegra20 platforms to use pinctrl defines
  ARM: tegra: convert dts files of Tegra114 platforms to use pinctrl defines
  ARM: tegra: Add header file for pinctrl constants
  ARM: tegra: convert device tree files to use key defines
  ARM: tegra: Enable PWM on Venice2
  ARM: tegra: Add Tegra124 PWM support
  ARM: tegra: add sound card to Venice2 DT
  ARM: tegra: add audio-related device to Tegra124 DT
  ARM: tegra: enable I2C controllers on Venice2
  ARM: tegra: add I2C controllers to Tegra124 DT
  ARM: tegra: add MMC controllers to Tegra124 DT
  ARM: tegra: add Tegra124 pinmux node to DT
  ARM: tegra: add APB DMA controller to Tegra124 DT
  ARM: tegra: add reset properties to Tegra124 DTs
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.

* tegra/dma-reset-rework: (320 commits)
  spi: tegra: checking for ERR_PTR instead of NULL
  ASoC: tegra: update module reset list for Tegra124
  clk: tegra: remove bogus PCIE_XCLK
  clk: tegra: remove legacy reset APIs
  ARM: tegra: remove legacy DMA entries from DT
  ARM: tegra: remove legacy clock entries from DT
  USB: EHCI: tegra: use reset framework
  Input: tegra-kbc - use reset framework
  serial: tegra: convert to standard DMA DT bindings
  serial: tegra: use reset framework
  spi: tegra: convert to standard DMA DT bindings
  spi: tegra: use reset framework
  staging: nvec: use reset framework
  i2c: tegra: use reset framework
  ASoC: tegra: convert to standard DMA DT bindings
  ASoC: tegra: allocate AHUB FIFO during probe() not startup()
  ASoC: tegra: call pm_runtime APIs around register accesses
  ASoC: tegra: use reset framework
  dma: tegra: register as an OF DMA controller
  dma: tegra: use reset framework
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

This reverts commit b652896b.

Unfortunately this commit prevents multiplatform from booting to
the point where a serial console is available. Revert it while
a solution is sought.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This reverts commit 6dea2c1e.

Unfortunately this commit prevents multiplatform from booting to
the point where a serial console is available. Revert it while
a solution is sought.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds DT board setup for the LaCie NAS LaPlug.

Chipset list:
- CPU MARVELL 88FR131 800Mhz
- SDRAM memory: 128MB DDR2-800 400Mhz
- 1 Ethernet Gigabit port (PHY MARVELL 88E1318)
- 1 Mini PCI-Express port
- 1 NAND 512 MB
- 1 push button
- 2 LEDs (red and blue)
- 4 USB Ports
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This file is mainly a copy of kirkwood-6281.dtsi.
The pinctrl seems to be the same.
These platforms differs only with their CPU, memory capabilities and the
number of GPIO available (36 on 6192, 50 on 6281).
Signed-off-by: Maxime Hadjinlian <maxime.hadjinlian@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The per-CPU PMSU registers documented in the datasheet start at
0x22100 and the last register for CPU3 is at 0x22428. However, the DT
informations use <0x22100 0x430>, which makes the region end at
0x22530 and not 0x22430.

Moreover, looking at the datasheet, we can see that the registers for
CPU0 start at 0x22100, for CPU1 at 0x22200, for CPU2 at 0x22300 and
for CPU3 at 0x22400. It seems clear that 0x100 bytes of registers have
been used per CPU.

Therefore, this commit reduces the length of the PMSU per-CPU register
area from the incorrect 0x430 bytes to a more logical 0x400 bytes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Now that the DTS file r8a7790-koelsch.dts can be used with
board-koelsch.c and board-koelsch-reference.c, proceed with removing
r8a7790-koelsch-reference.dts.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

From Kukjin Kim:
Samsung DT 2nd updates for v3.14
- add DMA controller, SPI, and TMU DT nodes for exynos5420
- add PWM DT nodes for exynos5250 and exynos5420
- drop interrupt controller properties from MCT nodes
  because MCT is not an interrupt controller
- move MCT nodes to exynos4x12 from board because it is
  a per-processor interrupt and same 4212 and 4412
- use one cell for MCT interrupt map for exynos4 SoCs
- update Exynos MCT DT bindings accordingly
- fix missing spaces after labels for exynos
- fix mmc status property for exynos5250-snow
- add MCLK for codec for exynos5250-smdk5250
- disable SPI and I2C by default for exynos5250 SoC
  and enable into requiring some boards
- rename cros5250-common to exynos5250-cros-common

* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (27 commits)
  ARM: dts: Rename Exynos5250 ChromeOS common file to have exynos prefix
  ARM: dts: Disable I2C controllers by default on Exynos5250
  ARM: dts: Leave Exynos5250 SPI controller disabled by default
  ARM: dts: Add CODEC MCLK for SMDK5250
  ARM: dts: Add device nodes for TMU blocks for exynos5420
  ARM: dts: Fix status property of mmc nodes for snow board
  ARM: dts: Fix missing spaces after labels for exynos
  ARM: dts: Simplify MCT interrupt map for exynos4 SoCs
  ARM: dts: Move MCT node to exynos4x12.dtsi
  ARM: dts: Drop interrupt controller properties from MCT nodes for exynos4 SoCs
  Documentation: devicetree: Update Exynos MCT bindings description
  ARM: dts: add pwm DT nodes to Exynos5250 and Exynos5420
  ARM: dts: Add SPI nodes to the exynos5420 device tree file
  ARM: dts: Add DMA controller node info on Exynos5420
  ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
  ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
  ARM: dts: add clock provider for mshc node for Exynos4412 SOC
  clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
  ARM: dts: Fix exynos5250-snow's search key to be L_META
  ARM: dts: Add the missing "\" key in non-US keyboards for exynos5250-snow
  ...
Signed-off-by: Olof Johansson <olof@lixom.net>

From Nicolas Ferre:
Second DT pull-request for 3.14
- now that PWM driver is on its way to mainline,
  we can integrate the DT entries
- As an example, use PWM for at91sam9m10g45ek leds
- Addition of clock specification for newly introduced
  crypto DT entries

* tag 'at91-dt2' of git://github.com/at91linux/linux-at91:
  ARM: at91/dt: add clk properties to sama5d3 TDES device node
  ARM: at91/dt: add clk properties to sama5d3 AES device node
  ARM: at91/dt: add clk properties to sama5d3 SHA device node
  ARM: at91: at91sam9m10g45ek: switch to PWM leds
  ARM: at91: add PWM device node
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

From Kukjin Kim:
Samsung DT updates for v3.14
- Add support Octa Cores for exynos5420
  : populate CPU node entries to 8 Cores
  : extend mct to support 8 local interrupts
- Update dwmmc nodes for exynos5250 and exynos5420
  : change status property of dwmmc nodes for exynos5250
  : move dwmmc nodes from exynos5 to exynos5250 because
    it's different between exynos5250 and exynos5420
  : rename mmc nodes from dwmmc for exynos5 SoCs
  : add dwmmc nodes for exynos5420
- Add G-Scaler nodes for exynos5420
- Add HS-i2c nodes in exynos5420
  : High Speed I2C 7 channels (4 to 10)
- Update sysreg binding and node name in exynos4
- Update min voltage on exynos5250-arndale
- Move fifo-depth property from boards to exynos5250 SoC
  : because the fifo-depth property is SoC specific

* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Update Samsung sysreg binding document
  ARM: dts: Fix sysreg node name in exynos4.dtsi
  ARM: dts: Add hs-i2c nodes to exynos5420
  ARM: dts: Update min voltage for vdd_arm on Arndale
  ARM: dts: populate cpu node entries to 8 cpus for exynos5420
  clocksource: mct: extend mct to support 8 local interrupts for Exynos5420
  ARM: dts: Add device nodes for GScaler blocks for exynos5420
  ARM: dts: Add dwmmc DT nodes for exynos5420 SOC
  ARM: dts: rename mmc dts node for exynos5 series
  ARM: dts: Move fifo-depth property from exynos5250 board dts
  ARM: dts: change status property of dwmmc nodes for exynos5250
  ARM: dts: Move dwmmc nodes from exynos5.dtsi to exynos5250.dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>

Add a generic (dtsi) include file for MOXA ART SoCs.

Also add a file for UC-7112-LX.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

From Michal Simek:

arm: Xilinx Zynq dt patches for v3.14

- Add gem support
- Add cpus node
- TTC cleanup

* tag 'zynq-dt-for-3.14' of git://git.xilinx.com/linux-xlnx:
  arm: dt: zynq: Add 'cpus' node
  arm: dt: zynq: Remove 'clock-ranges' from TTC nodes
  ARM: zynq: add gem support
Signed-off-by: Olof Johansson <olof@lixom.net>

We recently sorted the nodes in dove, orion5x, kirkwood, and armada
370/xp.  However, I missed this file.  -6281 is fine.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Add nodes for the two SATA PHYs on kirkwood.
Add node for the one SATA PHY on Dove.
Add pHandles to the PHYs in the sata nodes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Make it easier to notice the common file for ChromeOS devices based on
the Exynos5250 by giving it the exynos5250 prefix that the boards have.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Ensure that unused I2C controllers are not activated, causing problems due
to inappropriate pinmuxing or similar, by marking the controllers as
disabled by default and requiring boards to explicitly enable those that
are in use.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>