- 18 Apr, 2012 11 commits
-
-
David Spinadel authored
Please merge this with "iwlwifi: op_mode holds its pointer to the config" Signed-off-by:
David Spinadel <david.spinadel@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
David Spinadel authored
Changed disable calibration bit field defines to enum. Signed-off-by:
-
Emmanuel Grumbach authored
Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
It is not needed any more. Signed-off-by:
-
Emmanuel Grumbach authored
Each modules will hold a pointer to struct device instead. Signed-off-by:
-
Emmanuel Grumbach authored
Instead of using the shared area that we be killed. Signed-off-by:
-
Emmanuel Grumbach authored
Instead of using the shared area that we be killed. Remove the pointer to config from shared since it is not used any more. Signed-off-by:
-
Emmanuel Grumbach authored
Instead of using the shared area that will be killed. Signed-off-by:
-
Emmanuel Grumbach authored
Instead of using the shared area that we be killed. Signed-off-by:
-
Emmanuel Grumbach authored
Instead of using the shared area that we be killed. Signed-off-by:
-
Emmanuel Grumbach authored
The driver layer now holds a pointer to the transport, and shrd->drv is not needed any more, so kill it. Signed-off-by:
-
- 17 Apr, 2012 13 commits
-
-
Amitkumar Karwar authored
We get two timing related fields for each bss from firmware in scan results. 1) timestamp - Actual timestamp information in probe response/beacon 2) network_tsf - firmware's TSF value at the time the beacon or probe response was received. Both are needed while associating by firmware. The patch takes care of following things. 1) We should pass "timestamp" to cfg80211_inform_bss(), but currently "network_tsf" is being provided. This error is corrected here. 2) Rename "network_tsf" to "fw_tsf" 3) Make use of u64 variable instead of an array of u8/u32 to save parsed "timestamp" information. 4) Use timestamp provided to stack in scan results using cfg80211_inform_bss() while associating. (bss->tsf) 5) Allocate space to save fw_tsf in "priv" of cfg80211_bss and retrieve it while associating. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Amitkumar Karwar authored
Rearrange some code to save extra parameters to the functions. Signed-off-by:
-
Daniel Drake authored
Signed-off-by:
Daniel Drake <dsd@laptop.org> Acked-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Daniel Drake authored
Signed-off-by:
-
Daniel Drake authored
As described at http://article.gmane.org/gmane.linux.kernel.wireless.general/86084 libertas is taking a long time to load because it loads firmware during module loading. Add a new API for interface drivers to load their firmware asynchronously. The same semantics of the firmware table are followed like before. Interface drivers will be converted in follow-up patches, then we can remove the old, synchronous firmware loading function. Signed-off-by:
-
Daniel Drake authored
These simple sanity check avoids extra complexity in error paths when moving to asynchronous firmware loading (which means the device may fail to init some time after its creation). Signed-off-by:
-
Daniel Drake authored
Remove the ability to pass module parameters with firmware filenames for USB and SDIO interfaces. Remove the ability to pass custom "user" filenames to lbs_get_firmware(). Remove the ability to reprogram internal device memory with a different firmware from the USB driver (we don't know of any users), and simplify the OLPC firmware loading quirk to simply placing the OLPC firmware at the top of the list (we don't know of any users other than OLPC). Move lbs_get_firmware() into its own file. These simplifications should have no real-life effect but make the upcoming transition to asynchronous firmware loading considerably less painful. Signed-off-by:
-
Andreas Hartmann authored
There are connection stalls or very poor throughputs with rt2800 hardware using 802.11n in AP mode since patch "mac80211: retry sending failed BAR frames later instead of tearing down aggr"[1][2]. Since rt2800 hardware is not able to correctly report the tx status of BAR frames, this patch removes as workaround the existing error handling on AP side, which lets mac80211 send a BAR when an AMPDU subframe fails. As a result, most wifi clients (aside from Intel STAs on Windows) instead will timeout now the reorder buffer and request the lost frame again. The correct solution would be, to tear down BA session on AP side. This patch was born on the basis of "[RFT] rt2x00: Tear down BA session on QoS frame failure"[3]. Thanks to Helmut Schaa for his support! [1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/83297/focus=83304 [2] http://git.kernel.org/?p=linux/kernel/git/linville/wireless-testing.git;a=commit;h=f0425beda4d404a6e751439b562100b902ba9c98 [3] http://thread.gmane.org/gmane.linux.drivers.rt2x00.user/569Signed-off-by:
Andreas Hartmann <andihartmann@01019freenet.de> Acked-by:
Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
-
Gabor Juhos authored
The FBIN2FREQ macro and the ath9k_hw_fbin2freq function does the same thing. Remove the macro, and use the inline function instead. Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Signed-off-by:
-
Gabor Juhos authored
Both eeprom.c and ar9003_eeprom.c has an indentical 'ath9k_hw_fbin2freq' function. Move the function to a common place and remove the duplicates. Signed-off-by:
-
Gabor Juhos authored
Signed-off-by:
-
Gabor Juhos authored
The existing constants are used for reduction/increase tx power level on devices with 2x2 and 3x3 chainmask. Both reduction and increase must use the same value, so it makes no sense to use separate constants for them. Signed-off-by:
-
Julia Lawall authored
Add a corresponding leave call on error failure. Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Acked-by:
-
- 16 Apr, 2012 16 commits
-
-
Johannes Berg authored
The command strings are needed through the layers for debug and error messages, but can differ with opmode. As a result, we need to give the command names to the transport layer as configuration. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
Having a u32 before a potential 64-bit value is not very efficient, move it last. Signed-off-by:
-
David Spinadel authored
To support hybrid state of MVM op_mode, most of the functioanallity will be done using DVM functions. When MVM will have independant live, the declarations will be removed and the functions will be static back. Signed-off-by:
-
David Spinadel authored
Implement mapping of channel to TX power channel group, for sending channel specific data before add context. Signed-off-by:
-
Dor Shaish authored
Add a variable for disabling specific calibrations. Merged old variables for calibrations disabling. Signed-off-by:
Dor Shaish <dor.shaish@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
Signed-off-by:
-
David Spinadel authored
Signed-off-by:
-
David Spinadel authored
Set size of firmware section in mvm bundle format. Signed-off-by:
-
Johannes Berg authored
The declaration isn't needed as the struct is only used in code that includes the right header file. Signed-off-by:
-
Don Fry authored
The code has been changed, move the definitions to the proper file being used by the code. Signed-off-by:
Don Fry <donald.h.fry@intel.com> Signed-off-by:
-
Amit Beka authored
This register is used to enable some debug mechanisms. Signed-off-by:
Amit Beka <amit.beka@intel.com> Signed-off-by:
-
Don Fry authored
The HCMD_ACTIVE bit is only used in trans. Signed-off-by:
-
Don Fry authored
When WiMax takes over the RF, inform the op_mode. Signed-off-by:
-
Johannes Berg authored
It doesn't even exist as a module parameter, so just remove the item from the struct. Signed-off-by:
-
Johannes Berg authored
We've never released firmware using the alternatives mechanism and our build process makes that difficult anyway. This means that in every file we have ever built (except maybe by hand for testing) the listed alternative was 0. Make the alternative field in the TLVs part of the TLV number (thus expanding that to 32 bits); this gives us more TLV numbers (not really needed) and more importantly protects against rogue firmware files that actually do use the alternatives mechanism -- those will now be rejected since they don't contain any valid TLVs. Signed-off-by:
-
Johannes Berg authored
My original idea with this was to adjust the sleep pattern of the uCode based on the maximum network latency userspace asked for. Due to nobody wanting to test it, this logic was disabled by default. It seems the time has come to remove it, since it's not only always disabled but there also don't seem to be any applications that actually request a max network latency. Signed-off-by:
-
