- 18 Feb, 2019 36 commits
-
-
Vivek Kasireddy authored
The formats added in this patch include: V4L2_PIX_FMT_AYUV32 V4L2_PIX_FMT_XYUV32 V4L2_PIX_FMT_VUYA32 V4L2_PIX_FMT_VUYX32 These formats enable the trasmission of alpha channel data to other drivers and userspace applications in addition to YUV data. For example, buffers generated by drivers in one of these formats can be used by the Weston compositor to display as a texture or flipped directly onto the overlay planes with the help of a DRM driver. Signed-off-by:
Vivek Kasireddy <vivek.kasireddy@intel.com> Signed-off-by:
Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by:
Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
-
Cody P Schafer authored
Without this, we get failures like this when the kernel attempts to initialize a cx231xx device: [16046.153653] cx231xx 3-1.2:1.1: New device Hauppauge Hauppauge Device @ 480 Mbps (2040:c200) with 6 interfaces [16046.153900] cx231xx 3-1.2:1.1: can't change interface 3 alt no. to 3: Max. Pkt size = 0 [16046.153907] cx231xx 3-1.2:1.1: Identified as Hauppauge USB Live 2 (card=9) [16046.154350] i2c i2c-11: Added multiplexed i2c bus 13 [16046.154379] i2c i2c-11: Added multiplexed i2c bus 14 [16046.267194] cx25840 10-0044: cx23102 A/V decoder found @ 0x88 (cx231xx #0-0) [16048.424551] cx25840 10-0044: loaded v4l-cx231xx-avcore-01.fw firmware (16382 bytes) [16048.463224] cx231xx 3-1.2:1.1: v4l2 driver version 0.0.3 [16048.567878] cx231xx 3-1.2:1.1: Registered video device video2 [v4l2] [16048.568001] cx231xx 3-1.2:1.1: Registered VBI device vbi0 [16048.568419] cx231xx 3-1.2:1.1: audio EndPoint Addr 0x83, Alternate settings: 3 [16048.568425] cx231xx 3-1.2:1.1: video EndPoint Addr 0x84, Alternate settings: 5 [16048.568431] cx231xx 3-1.2:1.1: VBI EndPoint Addr 0x85, Alternate settings: 2 [16048.568436] cx231xx 3-1.2:1.1: sliced CC EndPoint Addr 0x86, Alternate settings: 2 [16048.568448] usb 3-1.2: couldn't get decoder output pad for V4L I/O [16048.568453] cx231xx 3-1.2:1.1: V4L2 device vbi0 deregistered [16048.568579] cx231xx 3-1.2:1.1: V4L2 device video2 deregistered [16048.569001] cx231xx: probe of 3-1.2:1.1 failed with error -22 Likely a regession since Commit 9d6d20e6 ("media: v4l2-mc: switch it to use the new approach to setup pipelines") (v4.19-rc1-100-g9d6d20e6), which introduced the use of PAD_SIGNAL_DV within v4l2_mc_create_media_graph(). This also modifies cx25840 to remove the VBI pad, matching the action taken in Commit 092a3787 ("media: v4l2: remove VBI output pad"). Fixes: 9d6d20e6 ("media: v4l2-mc: switch it to use the new approach to setup pipelines") Cc: stable@vger.kernel.org Signed-off-by:
Cody P Schafer <dev@codyps.com> Tested-by:
-
Colin Ian King authored
There is a spelling mistake in a fmdbg debug message. Fix it. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Hans Verkuil authored
media_device_cleanup() wasn't called, which caused a small memory leak. Signed-off-by:
-
Hans Verkuil authored
When the media device registration fails, don't call media_device_unregister since the device was never actually registered. When removing the module also call media_device_cleanup() to avoid a memory leak. Signed-off-by:
-
Sakari Ailus authored
This patch makes the SoC camera framework as well as effectively the few remaining sensor drivers depend on BROKEN, rendering it uncompileable without changes in Kconfig. The purpose is to leave the code around if someone wishes to convert the drivers to the modern day V4L2 sub-device framework without having to go to see development history in git. Signed-off-by:
Sakari Ailus <sakari.ailus@linux.intel.com> Acked-by:
-
Sakari Ailus authored
Move the mt9t031 driver to the soc_camera directory in the media staging tree. Signed-off-by:
-
Sakari Ailus authored
Move the imx074 driver to the soc_camera directory in the media staging tree. Signed-off-by:
-
Sakari Ailus authored
The SoC camera framework has no functional drivers left, something that has not changed for years. Move the leftovers to the staging tree. Signed-off-by:
-
Sakari Ailus authored
There is a V4L2 sub-device sensor driver for the rj45n1. As there is already another driver, remove the SoC camera one. Signed-off-by:
-
Sakari Ailus authored
There is a V4L2 sub-device sensor driver for the mt9m001. There is already a non-soc_camera driver. So, remove the SoC camera one. Signed-off-by:
-
Yong Zhi authored
This addresses the below TODO item, no function related changes: - Prefix imgu for all public APIs, i.e. change ipu3_v4l2_register() to imgu_v4l2_register(). (Sakari) The changes were obtained by applying the following perl script to driver code under drivers/staging/media/ipu3/. perl -pi.back -e 's/ipu3_(?!uapi)/imgu_/g;' Signed-off-by:
Yong Zhi <yong.zhi@intel.com> Signed-off-by:
-
Loic Poulain authored
According to the ov5640 specification (2.7 power up sequence), host can access the sensor's registers 20ms after reset. Trying to access them before leads to undefined behavior and result in sporadic initialization errors. Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Signed-off-by:
-
Jagan Teki authored
The ov5640_try_frame_interval operation updates the FPS as per user input based on default ov5640_frame_rate, OV5640_30_FPS which is failed to update when user trigger 15fps. So, initialize the default ov5640_frame_rate to OV5640_15_FPS so-that it can satisfy to update all fps. Fixes: 5a3ad937 ("media: ov5640: Make the return rate type more explicit") Signed-off-by:
Jagan Teki <jagan@amarulasolutions.com> Acked-by:
Jacopo Mondi <jacopo@jmondi.org> Signed-off-by:
-
Chen-Yu Tsai authored
The register value lists for all the supported resolution settings all include a register address/value pair for setting the JPEG compression mode. With the exception of 1080p (which sets mode 2), all resolutions use mode 3. The only difference between mode 2 and mode 3 is that mode 2 may have padding data on the last line, while mode 3 does not add padding data. As these register values were from dumps of running systems, and the difference between the modes is quite small, using mode 3 for all configurations should be OK. [Sakari Ailus: Align OV5640_REG_JPG_MODE_SELECT register naming.] Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Signed-off-by:
-
Chen-Yu Tsai authored
When compression is turned on, the on-bus data is framed according to the compression mode, and the height and width set in VFIFO_VSIZE and VFIFO_HSIZE. If these are not updated correctly, the sensor will send data framed in a manner unexpected by the capture interface, such as having more bytes per line than expected, and having the extra data dropped. This ultimately results in corrupted data. Set the two values when the media bus is configured for JPEG data, meaning the sensor would be in JPEG mode. Signed-off-by:
-
Chen-Yu Tsai authored
The OV5640 driver currently supports a static color bar pattern with a small vertical gamma gradient. The hardware also supports a color square pattern, as well as having a rolling bar for dynamic sequences. Add three more test patterns: - color bars with a rolling bar (but without the gamma gradient) - static color squares - color squares with a rolling bar Signed-off-by:
-
Chen-Yu Tsai authored
The transparent feature for test patterns blends the test pattern with an actual captured image. This makes the result non-static, subject to changes in the sensor's field of view. Test patterns should be predictable and deterministic, even if they are dynamic patterns. Disable the transparent feature of the test pattern. Signed-off-by:
-
Chen-Yu Tsai authored
The OV5640 can generate many types of test patterns, some with additional modifiers, such as a rolling bar, or gamma gradients. Add the bit definitions for all bits in the test pattern register, and use them to compose the values to be written to the register. Signed-off-by:
-
Chen-Yu Tsai authored
The OV5640 has many options for generating test patterns. Unfortunately there is only one V4L2 control for it. Thus the driver would need to list some or all combinations. Move the test_pattern_menu list before the ov5640_set_ctrl_test_pattern function that programs the hardware. This would allow us to add a matching list of values to program into the hardware, while keeping the two lists together for ease of maintenance. Signed-off-by:
-
Kieran Bingham authored
The ADV748X_PAGE_WAIT is a fake page to insert arbitrary delays in the register tables. Its only usage was removed, so we can remove the handling and simplify the code. Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
-
Kieran Bingham authored
The ADV748x is currently reset by writting a small table of registers to the device. The table lacks documentation and contains magic values to perform the actions, including using a fake register address to introduce a delay loop. Remove the table, and convert to code, documenting the purpose of the specific writes along the way. Signed-off-by:
-
Jacopo Mondi authored
When the adv748x driver is informed about a link being created from HDMI or AFE to a CSI-2 TX output, the 'link_setup()' callback is invoked. Make sure to implement proper routing management at link setup time, to route the selected video stream to the desired TX output. Signed-off-by:
Jacopo Mondi <jacopo+renesas@jmondi.org> Reviewed-by:
-
Jacopo Mondi authored
Both the AFE and HDMI s_stream routines (adv748x_afe_s_stream() and adv748x_hdmi_s_stream()) have to enable the CSI-2 TX they are streaming video data to. With the introduction of dynamic routing between HDMI and AFE entities to TXA, the video stream sink needs to be set at run time, and not statically selected as the s_stream functions are currently doing. To fix this, store a reference to the active CSI-2 TX sink for both HDMI and AFE sources, and operate on it when starting/stopping the stream. Reviewed-by:
-
Jacopo Mondi authored
The power_up_tx() procedure needs to set a few registers conditionally to the selected video source, but it currently checks for the provided tx to be either TXA or TXB. With the introduction of dynamic routing between HDMI and AFE entities to TXA, checking which TX the function is operating on is not meaningful anymore. To fix this, store the subdevice of the source providing video data to the CSI-2 TX in the 'struct adv748x_csi2' representing the TX and check on it. Reviewed-by:
-
Jacopo Mondi authored
The ADV748x chip supports routing AFE output to either TXA or TXB. In order to support run-time configuration of video stream path, create an additional (not enabled) "AFE:8->TXA:0" link, and remove the IMMUTABLE flag from existing ones. Reviewed-by:
-
Jacopo Mondi authored
Rename the chip reset procedure as they configure the CP (HDMI) and SD (AFE) cores. Reviewed-by:
-
Jacopo Mondi authored
Add small is_txb() macro to the existing is_txa() and use it where appropriate. Reviewed-by:
-
Hans Verkuil authored
The sd argument of this macro can be a more complex expression. Since it is used 5 times in the macro it can be evaluated that many times as well. So assign it to a temp variable in the beginning and use that instead. This also avoids any potential side-effects of evaluating sd. Signed-off-by:
-
Lucas A. M. Magalhães authored
Remove unused but set variables to clean up the code and avoid warning. Signed-off-by:
Lucas A. M. Magalhães <lucmaga@gmail.com> Signed-off-by:
-
Steve Longerbeam authored
The capture compose rectangle was not getting updated when setting the source subdevice's source pad format. This causes the compose window to be zero (or not updated) at stream start unless the capture device format was set explicitly at the capture device node. Fix by moving the calculation of the capture compose rectangle to imx_media_mbus_fmt_to_pix_fmt(), and pass the rectangle to imx_media_capture_device_set_format(). Fixes: 439d8186 ("media: imx: add capture compose rectangle") Signed-off-by:
Steve Longerbeam <slongerbeam@gmail.com> Signed-off-by:
-
Hans Verkuil authored
Add VB2_USERPTR to the vimc capture device. Signed-off-by:
Helen Koike <helen.koike@collabora.com> Signed-off-by:
-
Mauro Carvalho Chehab authored
A merge conflict rised when merging from -rc7. Fix it. In this specific case, we don't need the if anymore, as the work_run was moved to its rightful place (struct vim2m_ctx). Fixes: b3e64e5b ("media: vim2m: use per-file handler work queue") Fixes: 240809ef ("media: vim2m: only cancel work if it is for right context") Reviewed-by:
-
Ezequiel Garcia authored
The linked commit changed s_fmt/try_fmt to fail if num_planes is bogus. This, however, is against the spec, which mandates drivers to return a proper num_planes value, without an error. Replace the num_planes check and instead clamp it to a sane value, so we still make sure we don't overflow the planes array by accident. Fixes: 9048b2e1 ("media: v4l: ioctl: Validate num_planes before using it") Signed-off-by:
Ezequiel Garcia <ezequiel@collabora.com> Reviewed-by:
-
Mauro Carvalho Chehab authored
Linux 5.0-rc7 * tag 'v5.0-rc7': (1667 commits) Linux 5.0-rc7 Input: elan_i2c - add ACPI ID for touchpad in Lenovo V330-15ISK Input: st-keyscan - fix potential zalloc NULL dereference Input: apanel - switch to using brightness_set_blocking() powerpc/64s: Fix possible corruption on big endian due to pgd/pud_present() efi/arm: Revert "Defer persistent reservations until after paging_init()" arm64, mm, efi: Account for GICv3 LPI tables in static memblock reserve table sunrpc: fix 4 more call sites that were using stack memory with a scatterlist include/linux/module.h: copy __init/__exit attrs to init/cleanup_module Compiler Attributes: add support for __copy (gcc >= 9) lib/crc32.c: mark crc32_le_base/__crc32c_le_base aliases as __pure auxdisplay: ht16k33: fix potential user-after-free on module unload x86/platform/UV: Use efi_runtime_lock to serialise BIOS calls i2c: bcm2835: Clear current buffer pointers and counts after a transfer i2c: cadence: Fix the hold bit setting drm: Use array_size() when creating lease dm thin: fix bug where bio that overwrites thin block ignores FUA Revert "exec: load_script: don't blindly truncate shebang string" Revert "gfs2: read journal in large chunks to locate the head" net: ethernet: freescale: set FEC ethtool regs version ... Signed-off-by: -
Linus Torvalds authored
-
- 17 Feb, 2019 4 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull EFI fixes from Ingo Molnar: "This tree reverts a GICv3 commit (which was broken) and fixes it in another way, by adding a memblock build-time entries quirk for ARM64" * 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: efi/arm: Revert "Defer persistent reservations until after paging_init()" arm64, mm, efi: Account for GICv3 LPI tables in static memblock reserve table
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Ingo Molnar: "Three changes: - An UV fix/quirk to pull UV BIOS calls into the efi_runtime_lock locking regime. (This done by aliasing __efi_uv_runtime_lock to efi_runtime_lock, which should make the quirk nature obvious and maintain the general policy that the EFI lock (name...) isn't exposed to drivers.) - Our version of MAGA: Make a.out Great Again. - Add a new Intel model name enumerator to an upstream header to help reduce dependencies going forward" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/platform/UV: Use efi_runtime_lock to serialise BIOS calls x86/CPU: Add Icelake model number x86/a.out: Clear the dump structure initially -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Ingo Molnar: "Two fixes on the kernel side: fix an over-eager condition that failed larger perf ring-buffer sizes, plus fix crashes in the Intel BTS code for a corner case, found by fuzzing" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/core: Fix impossible ring-buffer sizes warning perf/x86: Add check_period PMU callback
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds authored
Pull powerpc fix from Michael Ellerman: "Just one fix, for pgd/pud_present() which were broken on big endian since v4.20, leading to possible data corruption. Thanks to: Aneesh Kumar K.V., Erhard F., Jan Kara" * tag 'powerpc-5.0-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/64s: Fix possible corruption on big endian due to pgd/pud_present()
-
