- 23 Feb, 2015 20 commits
-
-
Laurent Pinchart authored
Enable the ethernet controller for the Alt board. Pin muxing entries are currently left out as r8a7794 pin control support isn't available yet. We thus rely on the boot loader to configure ethernet pins for now. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Laurent Pinchart authored
Add a DT node for the on-SoC ethernet controller device. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Laurent Pinchart authored
Add the six IPMMU instances found in the r8a7794 to DT with a disabled status. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Laurent Pinchart authored
Add the seven IPMMU instances found in the r8a7791 to DT with a disabled status. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Laurent Pinchart authored
Add the six IPMMU instances found in the r8a7790 to DT with a disabled status. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Laurent Pinchart authored
Instantiate the two system DMA controllers in the r8a7794 device tree. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
Traditionally, the first 16 MiB of RAM was reserved for the RT processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y, which requires that the start address of physical memory is a multiple of 128 MiB. As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare RAM to start at 0x40000000. While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is available. Note that kzm9g_defconfig still has CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so before the advent of DT we scribbled over the last 8 MiB, too. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
Traditionally, the first 16 MiB of RAM was reserved for the RT processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y, which requires that the start address of physical memory is a multiple of 128 MiB. As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare RAM to start at 0x40000000. While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is available. Note that kzm9g_defconfig still has CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so before the advent of DT we scribbled over the last 8 MiB, too. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Ulrich Hecht authored
Specifies clock sources and register bits. Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> [geert: Drop renesas,src-shift/renesas,src-width, pad to 4 or 8 parents] Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
This clock drives the irqpin controller modules. Before, it was assumed enabled by the bootloader or reset state. By making it available to the driver, we make sure it gets enabled when needed, and allow it to be managed by system or runtime PM. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Laurent Pinchart authored
Enable the kzm9g touchscreen controller in the board's DT file. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
Add a DT node for the R2025D real-time clock, which is connected to i2c0. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
Add a DT node for the ADXL345 three-axis digital accelerometer sensor, which is connected to i2c0. As trivial i2c devices are matched against the first compatible entry only, compatibility is declared with "adi,adxl34x" only for now. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> The device needs an interrupt to operate properly. Specify the two interrupts used on the board. While at it rename the DT node to accelerometer@1d to describe the device's function instead of its model. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
Add a DT node for the AK8975 magnetometer sensor, which is connected to i2c0. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Specify the device interrupt to avoid polling for end of conversion. While at it rename the DT node to compass@c to describe the device's function instead of its model. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Geert Uytterhoeven authored
While at it rename the ak4648 node to "codec" to describe the device's function instead of its model, and move its device-specific property after its generic properties. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Laurent Pinchart authored
The sh73a0 INTC can't mask interrupts properly most likely due to a hardware bug. Set the control-parent property to delegate masking to the parent interrupt controller. Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Ulrich Hecht authored
This adds the remaining DIV6 clocks and all possible parents for the SUB clock. Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
-
Linus Torvalds authored
.. after extensive statistical analysis of my G+ polling, I've come to the inescapable conclusion that internet polls are bad. Big surprise. But "Hurr durr I'ma sheep" trounced "I like online polls" by a 62-to-38% margin, in a poll that people weren't even supposed to participate in. Who can argue with solid numbers like that? 5,796 votes from people who can't even follow the most basic directions? In contrast, "v4.0" beat out "v3.20" by a slimmer margin of 56-to-44%, but with a total of 29,110 votes right now. Now, arguably, that vote spread is only about 3,200 votes, which is less than the almost six thousand votes that the "please ignore" poll got, so it could be considered noise. But hey, I asked, so I'll honor the votes.
-
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4Linus Torvalds authored
Pull ext4 fixes from Ted Ts'o: "Ext4 bug fixes. We also reserved code points for encryption and read-only images (for which the implementation is mostly just the reserved code point for a read-only feature :-)" * tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: ext4: fix indirect punch hole corruption ext4: ignore journal checksum on remount; don't fail ext4: remove duplicate remount check for JOURNAL_CHECKSUM change ext4: fix mmap data corruption in nodelalloc mode when blocksize < pagesize ext4: support read-only images ext4: change to use setup_timer() instead of init_timer() ext4: reserve codepoints used by the ext4 encryption feature jbd2: complain about descriptor block checksum errors
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull more vfs updates from Al Viro: "Assorted stuff from this cycle. The big ones here are multilayer overlayfs from Miklos and beginning of sorting ->d_inode accesses out from David" * 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (51 commits) autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation procfs: fix race between symlink removals and traversals debugfs: leave freeing a symlink body until inode eviction Documentation/filesystems/Locking: ->get_sb() is long gone trylock_super(): replacement for grab_super_passive() fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry) SELinux: Use d_is_positive() rather than testing dentry->d_inode Smack: Use d_is_positive() rather than testing dentry->d_inode TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR() Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb VFS: Split DCACHE_FILE_TYPE into regular and special types VFS: Add a fallthrough flag for marking virtual dentries VFS: Add a whiteout dentry type VFS: Introduce inode-getting helpers for layered/unioned fs environments Infiniband: Fix potential NULL d_inode dereference posix_acl: fix reference leaks in posix_acl_create autofs4: Wrong format for printing dentry ...
-
- 22 Feb, 2015 20 commits
-
-
git://ftp.arm.linux.org.uk/~rmk/linux-armLinus Torvalds authored
Pull ARM fix from Russell King: "Just one fix this time around. __iommu_alloc_buffer() can cause a BUG() if dma_alloc_coherent() is called with either __GFP_DMA32 or __GFP_HIGHMEM set. The patch from Alexandre addresses this" * 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: ARM: 8305/1: DMA: Fix kzalloc flags in __iommu_alloc_buffer()
-
Al Viro authored
X-Coverup: just ask spender Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
use_pde()/unuse_pde() in ->follow_link()/->put_link() resp. Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
As it is, we have debugfs_remove() racing with symlink traversals. Supply ->evict_inode() and do freeing there - inode will remain pinned until we are done with the symlink body. And rip the idiocy with checking if dentry is positive right after we'd verified debugfs_positive(), which is a stronger check... Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Konstantin Khlebnikov authored
I've noticed significant locking contention in memory reclaimer around sb_lock inside grab_super_passive(). Grab_super_passive() is called from two places: in icache/dcache shrinkers (function super_cache_scan) and from writeback (function __writeback_inodes_wb). Both are required for progress in memory allocator. Grab_super_passive() acquires sb_lock to increment sb->s_count and check sb->s_instances. It seems sb->s_umount locked for read is enough here: super-block deactivation always runs under sb->s_umount locked for write. Protecting super-block itself isn't a problem: in super_cache_scan() sb is protected by shrinker_rwsem: it cannot be freed if its slab shrinkers are still active. Inside writeback super-block comes from inode from bdi writeback list under wb->list_lock. This patch removes locking sb_lock and checks s_instances under s_umount: generic_shutdown_super() unlinks it under sb->s_umount locked for write. New variant is called trylock_super() and since it only locks semaphore, callers must call up_read(&sb->s_umount) instead of drop_super(sb) when they're done. Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Fanotify probably doesn't want to watch autodirs so make it use d_can_lookup() rather than d_is_dir() when checking a dir watch and give an error on fake directories. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Fix up the following scripted S_ISDIR/S_ISREG/S_ISLNK conversions (or lack thereof) in cachefiles: (1) Cachefiles mostly wants to use d_can_lookup() rather than d_is_dir() as it doesn't want to deal with automounts in its cache. (2) Coccinelle didn't find S_IS* expressions in ASSERT() statements in cachefiles. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Convert the following where appropriate: (1) S_ISLNK(dentry->d_inode) to d_is_symlink(dentry). (2) S_ISREG(dentry->d_inode) to d_is_reg(dentry). (3) S_ISDIR(dentry->d_inode) to d_is_dir(dentry). This is actually more complicated than it appears as some calls should be converted to d_can_lookup() instead. The difference is whether the directory in question is a real dir with a ->lookup op or whether it's a fake dir with a ->d_automount op. In some circumstances, we can subsume checks for dentry->d_inode not being NULL into this, provided we the code isn't in a filesystem that expects d_inode to be NULL if the dirent really *is* negative (ie. if we're going to use d_inode() rather than d_backing_inode() to get the inode pointer). Note that the dentry type field may be set to something other than DCACHE_MISS_TYPE when d_inode is NULL in the case of unionmount, where the VFS manages the fall-through from a negative dentry to a lower layer. In such a case, the dentry type of the negative union dentry is set to the same as the type of the lower dentry. However, if you know d_inode is not NULL at the call site, then you can use the d_is_xxx() functions even in a filesystem. There is one further complication: a 0,0 chardev dentry may be labelled DCACHE_WHITEOUT_TYPE rather than DCACHE_SPECIAL_TYPE. Strictly, this was intended for special directory entry types that don't have attached inodes. The following perl+coccinelle script was used: use strict; my @callers; open($fd, 'git grep -l \'S_IS[A-Z].*->d_inode\' |') || die "Can't grep for S_ISDIR and co. callers"; @callers = <$fd>; close($fd); unless (@callers) { print "No matches\n"; exit(0); } my @cocci = ( '@@', 'expression E;', '@@', '', '- S_ISLNK(E->d_inode->i_mode)', '+ d_is_symlink(E)', '', '@@', 'expression E;', '@@', '', '- S_ISDIR(E->d_inode->i_mode)', '+ d_is_dir(E)', '', '@@', 'expression E;', '@@', '', '- S_ISREG(E->d_inode->i_mode)', '+ d_is_reg(E)' ); my $coccifile = "tmp.sp.cocci"; open($fd, ">$coccifile") || die $coccifile; print($fd "$_\n") || die $coccifile foreach (@cocci); close($fd); foreach my $file (@callers) { chomp $file; print "Processing ", $file, "\n"; system("spatch", "--sp-file", $coccifile, $file, "--in-place", "--no-show-diff") == 0 || die "spatch failed"; } [AV: overlayfs parts skipped] Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Use d_is_positive() rather than testing dentry->d_inode in SELinux to get rid of direct references to d_inode outside of the VFS. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Use d_is_positive() rather than testing dentry->d_inode in Smack to get rid of direct references to d_inode outside of the VFS. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Use d_is_dir() rather than d_inode and S_ISDIR(). Note that this will include fake directories such as automount triggers. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Use d_is_positive(dentry) or d_is_negative(dentry) rather than testing dentry->d_inode as the dentry may cover another layer that has an inode when the top layer doesn't or may hold a 0,0 chardev that's actually a whiteout. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
mediated_filesystem() should use dentry->d_sb not dentry->d_inode->i_sb and should avoid file_inode() also since it is really dealing with the path. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Split DCACHE_FILE_TYPE into DCACHE_REGULAR_TYPE (dentries representing regular files) and DCACHE_SPECIAL_TYPE (representing blockdev, chardev, FIFO and socket files). d_is_reg() and d_is_special() are added to detect these subtypes and d_is_file() is left as the union of the two. This allows a number of places that use S_ISREG(dentry->d_inode->i_mode) to use d_is_reg(dentry) instead. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Add a DCACHE_FALLTHRU flag to indicate that, in a layered filesystem, this is a virtual dentry that covers another one in a lower layer that should be used instead. This may be recorded on medium if directory integration is stored there. The flag can be set with d_set_fallthru() and tested with d_is_fallthru(). Original-author: Valerie Aurora <vaurora@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Add DCACHE_WHITEOUT_TYPE and provide a d_is_whiteout() accessor function. A d_is_miss() accessor is also added for ordinary cache misses and d_is_negative() is modified to indicate either an ordinary miss or an enforced miss (whiteout). Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
David Howells authored
Introduce some function for getting the inode (and also the dentry) in an environment where layered/unioned filesystems are in operation. The problem is that we have places where we need *both* the union dentry and the lower source or workspace inode or dentry available, but we can only have a handle on one of them. Therefore we need to derive the handle to the other from that. The idea is to introduce an extra field in struct dentry that allows the union dentry to refer to and pin the lower dentry. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
git://git.linux-mips.org/pub/scm/ralf/upstream-linusLinus Torvalds authored
Pull MIPS updates from Ralf Baechle: "This is the main pull request for MIPS: - a number of fixes that didn't make the 3.19 release. - a number of cleanups. - preliminary support for Cavium's Octeon 3 SOCs which feature up to 48 MIPS64 R3 cores with FPU and hardware virtualization. - support for MIPS R6 processors. Revision 6 of the MIPS architecture is a major revision of the MIPS architecture which does away with many of original sins of the architecture such as branch delay slots. This and other changes in R6 require major changes throughout the entire MIPS core architecture code and make up for the lion share of this pull request. - finally some preparatory work for eXtendend Physical Address support, which allows support of up to 40 bit of physical address space on 32 bit processors" [ Ahh, MIPS can't leave the PAE brain damage alone. It's like every CPU architect has to make that mistake, but pee in the snow by changing the TLA. But whether it's called PAE, LPAE or XPA, it's horrid crud - Linus ] * 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits) MIPS: sead3: Corrected get_c0_perfcount_int MIPS: mm: Remove dead macro definitions MIPS: OCTEON: irq: add CIB and other fixes MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs. MIPS: OCTEON: More OCTEONIII support MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits. MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup. MIPS: OCTEON: Update octeon-model.h code for new SoCs. MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h MIPS: OCTEON: Implement the core-16057 workaround MIPS: OCTEON: Delete unused COP2 saving code MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register MIPS: OCTEON: Save and restore CP2 SHA3 state MIPS: OCTEON: Fix FP context save. MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs MIPS: boot: Provide more uImage options MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h MIPS: ip22-gio: Remove legacy suspend/resume support mips: pci: Add ifdef around pci_proc_domain ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM SoC fixes from Arnd Bergmann: "A few fixes that came in too late to make it into the first set of pull requests but would still be nice to have in -rc1. The majority of these are trivial build fixes for bugs that I found myself using randconfig testing, and a set of two patches from Uwe to mark DT strings as 'const' where appropriate, to resolve inconsistent section attributes" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: ARM: make of_device_ids const ARM: make arrays containing machine compatible strings const ARM: mm: Remove Kconfig symbol CACHE_PL310 ARM: rockchip: force built-in regulator support for PM ARM: mvebu: build armada375-smp code conditionally ARM: sti: always enable RESET_CONTROLLER ARM: rockchip: make rockchip_suspend_init conditional ARM: ixp4xx: fix {in,out}s{bwl} data types ARM: prima2: do not select SMP_ON_UP ARM: at91: fix pm declarations ARM: davinci: multi-soc kernels require AUTO_ZRELADDR ARM: davinci: davinci_cfg_reg cannot be init ARM: BCM: put back ARCH_MULTI_V7 dependency for mobile ARM: vexpress: use ARM_CPU_SUSPEND if needed ARM: dts: add I2C device nodes for Broadcom Cygnus ARM: dts: BCM63xx: fix L2 cache properties
-