Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

When an adapter gets powered off or is removed any pending commands
should receive a ENETDOWN or ENODEV status response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

It's convenient to use the HCI device index the AMP controller id, but
the spec requires that an AMP controller never has id 0.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

AMP channels can be moved between BR/EDR and AMP controllers using a
sequence of signals. Every attempted channel move involves a series of
four signals:

   Move Initiator                 Move Responder
        |                                 |
        |       Move Channel Request      |
        |  ---------------------------->  |
        |                                 |
        |       Move Channel Response     |
        |  <----------------------------  |
        |                                 |
        |       Move Channel Confirm      |
        |  ---------------------------->  |
        |                                 |
        |  Move Channel Confirm Response  |
	|  <----------------------------  |

All four signals are sent even if the move fails.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

The A2MP fixed channel bit is only set when high-speed mode is enabled.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Symbolic fixed channel IDs will be used instead of magic numbers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Handle both "create channel request" and "create channel response".
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

AMP channel creation and channel moves are coordinated using the L2CAP
signaling channel.  These definitions cover the "create channel",
"move channel", and "move channel confirm" signals.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Each channel has a policy to require BR/EDR (the default),
prefer BR/EDR, or prefer AMP.

Check for valid policy value and L2CAP mode.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This variable is currently only accessible within l2cap_core.c, but
it is also needed in l2cap_sock.c
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Allow control of AMP functionality on L2CAP sockets. By default,
connections will be restricted to BR/EDR.  Manipulating the
BT_CHANNEL_POLICY option allows for channels to be moved to or created
on AMP controllers.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

tx_win_max is initialized during L2CAP configuration phase. For fixed
channels (e.g. A2MP) we want to have it initialized when channel is
created.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

To avoid starvation the priority is recalculated so that the starving
channels are promoted to HCI_PRIO_MAX - 1 (6).

HCI_PRIO_MAX (7) is considered special, because it requires CAP_NET_ADMIN
capability which can be used to provide more guaranties, so it is not used
when promoting.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

The quote is calculated based on the first buffer in the queue so if the
priority changes to something lower than the priority of the first skb
the quote needs to be recalculated.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This implement priority based scheduler using skbuffer priority set via
SO_PRIORITY socket option.

It introduces hci_chan_hash (list of HCI Channel/hci_chan) per connection,
each item in this list refer to a L2CAP connection and it is used to
queue the data for transmission.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This functions needs crtl_sock and intr_sock to be set first.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Calling module_put(THIS_MODULE) is *never* safe when we cannot go sure that we
own at least two references. This is because the call may unload our module
before it returns and then the "return" will jump into invalid memory.

Gladly, module.h provides a wrapper for kthread-users: module_put_and_exit().
This puts our module and then exits the kthread without returning to the module.

This patch fixes the hidp kthread to use this wrapper instead of manually
freeing its own reference. See nfsd or lockd for other kthreads using this.

Calling __module_get() inside the kthread is safe as the hidp module will always
wait until the kthread sets "waiting_for_startup" to 0.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

When loading the usb-configuration we do not signal the end of configuration on
memory allocation error. This patch moves the memory allocation to the top so
every error path uses "goto error" now to correctly send the usb-ctrl message
when detecting some error.

This also replaces GFP_ATOMIC with GFP_KERNEL as we are allowed to sleep here.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

A workqueue is allowed to sleep so we can safely use GFP_KERNEL instead of
GFP_ATOMIC. This is still legacy code when the driver used timer BHs and not a
worqueue.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

When disconnecting a bcm203x device we kill and destroy the usb-urb, however,
there might still be a pending work-structure which resubmits the now invalid
urb. To avoid this race condition, we simply set a shutdown-flag and
synchronously kill the worker first.

This also adds a comment to all schedule_work()s, as it is really not clear
that they are used as replacement for short timers (which can be seen in the git
history).
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

We are allowed to sleep here so no need to use GFP_ATOMIC. The caller
(ath3k_probe) calls request_firmware() which definitely sleeps. Hence, we should
avoid using GFP_ATOMIC.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

The HCI_MGMT flag should only be set when user space requests the full
controller information. This way we avoid potential issues with setting
change events ariving before the actual read_controller_info command
finishes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

I've noticed that my CSR usb dongle was not working if it was plugged in when
PC was booting. It looks like I get two HCI reset command complete events (see
hcidump logs below).
The root cause is reset called from off_timer. Timeout for this reset to
complete is set to 250ms and my bt dongle requires more time for replying with
command complete event. After that, chip seems to reply with reset command
complete event for next non-reset command.

Attached patch increase mentioned timeout to HCI_INIT_TIMEOUT, this value is
already used for timeouting hci_reset_req in hci_dev_reset().

This might also be related to BT not working after suspend that was reported
here some time ago.

Hcidump log:

2011-09-12 23:13:27.379465 < HCI Command: Reset (0x03|0x0003) plen 0
2011-09-12 23:13:27.380797 > HCI Event: Command Complete (0x0e) plen 4
    Reset (0x03|0x0003) ncmd 1
    status 0x00
2011-09-12 23:13:27.380859 < HCI Command: Read Local Supported Features (0x04|0x000
3) plen 0
2011-09-12 23:13:27.760789 > HCI Event: Command Complete (0x0e) plen 4
    Reset (0x03|0x0003) ncmd 1
    status 0x00
2011-09-12 23:13:27.760831 < HCI Command: Read Local Version Information (0x04|0x00
01) plen 0
2011-09-12 23:13:27.764780 > HCI Event: Command Complete (0x0e) plen 12
    Read Local Version Information (0x04|0x0001) ncmd 1
    status 0x00
    HCI Version: 1.1 (0x1) HCI Revision: 0x36f
    LMP Version: 1.1 (0x1) LMP Subversion: 0x36f
    Manufacturer: Cambridge Silicon Radio (10)
Signed-off-by: Szymon Janc <szymon@janc.net.pl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This was triggered by turning off encryption on ACL link when rfcomm
was using high security. rfcomm_security_cfm (which is called from rx
task) was closing DLC and this involves sending disconnect message
(and locking socket).

Move closing DLC to rfcomm_process_dlcs and only flag DLC for closure
in rfcomm_security_cfm.

BUG: sleeping function called from invalid context at net/core/sock.c:2032
in_atomic(): 1, irqs_disabled(): 0, pid: 1788, name: kworker/0:3
[<c0068a08>] (unwind_backtrace+0x0/0x108) from [<c05e25dc>] (dump_stack+0x20/0x24)
[<c05e25dc>] (dump_stack+0x20/0x24) from [<c0087ba8>] (__might_sleep+0x110/0x12c)
[<c0087ba8>] (__might_sleep+0x110/0x12c) from [<c04801d8>] (lock_sock_nested+0x2c/0x64)
[<c04801d8>] (lock_sock_nested+0x2c/0x64) from [<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc)
[<c05670c8>] (l2cap_sock_sendmsg+0x58/0xcc) from [<c047cf6c>] (sock_sendmsg+0xb0/0xd0)
[<c047cf6c>] (sock_sendmsg+0xb0/0xd0) from [<c047cfc8>] (kernel_sendmsg+0x3c/0x44)
[<c047cfc8>] (kernel_sendmsg+0x3c/0x44) from [<c056b0e8>] (rfcomm_send_frame+0x50/0x58)
[<c056b0e8>] (rfcomm_send_frame+0x50/0x58) from [<c056b168>] (rfcomm_send_disc+0x78/0x80)
[<c056b168>] (rfcomm_send_disc+0x78/0x80) from [<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc)
[<c056b9f4>] (__rfcomm_dlc_close+0x2d0/0x2fc) from [<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0)
[<c056bbac>] (rfcomm_security_cfm+0x140/0x1e0) from [<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84)
[<c0555ec0>] (hci_event_packet+0x1ce8/0x4d84) from [<c0550380>] (hci_rx_task+0x1d0/0x2d0)
[<c0550380>] (hci_rx_task+0x1d0/0x2d0) from [<c009ee04>] (tasklet_action+0x138/0x1e4)
[<c009ee04>] (tasklet_action+0x138/0x1e4) from [<c009f21c>] (__do_softirq+0xcc/0x274)
[<c009f21c>] (__do_softirq+0xcc/0x274) from [<c009f6c0>] (do_softirq+0x60/0x6c)
[<c009f6c0>] (do_softirq+0x60/0x6c) from [<c009f794>] (local_bh_enable_ip+0xc8/0xd4)
[<c009f794>] (local_bh_enable_ip+0xc8/0xd4) from [<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c)
[<c05e5804>] (_raw_spin_unlock_bh+0x48/0x4c) from [<c040d470>] (data_from_chip+0xf4/0xaec)
[<c040d470>] (data_from_chip+0xf4/0xaec) from [<c04136c0>] (send_skb_to_core+0x40/0x178)
[<c04136c0>] (send_skb_to_core+0x40/0x178) from [<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0)
[<c04139f4>] (cg2900_hu_receive+0x15c/0x2d0) from [<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0)
[<c0414cb8>] (hci_uart_tty_receive+0x74/0xa0) from [<c02cbd9c>] (flush_to_ldisc+0x188/0x198)
[<c02cbd9c>] (flush_to_ldisc+0x188/0x198) from [<c00b2774>] (process_one_work+0x144/0x4b8)
[<c00b2774>] (process_one_work+0x144/0x4b8) from [<c00b2e8c>] (worker_thread+0x198/0x468)
[<c00b2e8c>] (worker_thread+0x198/0x468) from [<c00b9bc8>] (kthread+0x98/0xa0)
[<c00b9bc8>] (kthread+0x98/0xa0) from [<c0061744>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This patch adds the necessary code to send proper command status or
command complete events to the start/stop discovery management commands.
Before this patch these events were completely missing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This uses SO_PRIORITY to set the skbuffer priority field
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

When all items in the list have the same type there is no much of a point
to use list_for_each except if you want to use the list pointer itself.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

l2cap_set_timer function prints sk instead of chan pointer.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

make code readable by removing magic numbers
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Add L2CAP Config Pending state for EFS. Currently after receiving
Config Response Pending respond with Config Response Success.

...
> ACL data: handle 1 flags 0x02 dlen 16
    L2CAP(s): Connect rsp: dcid 0x0040 scid 0x0040 result 0 status 0
      Connection successful
> ACL data: handle 1 flags 0x02 dlen 45
    L2CAP(s): Config req: dcid 0x0040 flags 0x00 clen 33
      RFC 0x03 (Enhanced Retransmission, TxWin 63, MaxTx 3, RTo 0, MTo 0, MPS 1009)
      EFS (Id 0x01, SerType Best Effort, MaxSDU 0xffff, SDUitime 0xffffffff,
          AccLat 0xffffffff, FlushTO 0x0000ffff)
< ACL data: handle 1 flags 0x00 dlen 45
    L2CAP(s): Config req: dcid 0x0040 flags 0x00 clen 33
      RFC 0x03 (Enhanced Retransmission, TxWin 63, MaxTx 3, RTo 0, MTo 0, MPS 498)
      EFS (Id 0x01, SerType Best Effort, MaxSDU 0xffff, SDUitime 0xffffffff,
          AccLat 0xffffffff, FlushTO 0x0000ffff)
< ACL data: handle 1 flags 0x00 dlen 47
    L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 4 clen 33
      Pending
      MTU 672
      RFC 0x03 (Enhanced Retransmission, TxWin 63, MaxTx 3, RTo 2000, MTo 12000, MPS 498)
      EFS (Id 0x01, SerType Best Effort, MaxSDU 0xffff, SDUitime 0xffffffff,
          AccLat 0xffffffff, FlushTO 0x0000ffff)
> ACL data: handle 1 flags 0x02 dlen 47
    L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 4 clen 33
      Pending
      MTU 672
      RFC 0x03 (Enhanced Retransmission, TxWin 63, MaxTx 3, RTo 2000, MTo 12000, MPS 498)
      EFS (Id 0x01, SerType Best Effort, MaxSDU 0xffff, SDUitime 0xffffffff,
          AccLat 0xffffffff, FlushTO 0x0000ffff)
> ACL data: handle 1 flags 0x02 dlen 14
    L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 0 clen 0
      Success
< ACL data: handle 1 flags 0x00 dlen 14
    L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 0 clen 0
      Success
< ACL data: handle 1 flags 0x00 dlen 510
    L2CAP(d): cid 0x0040 len 506 ext_ctrl 0x00010000 fcs 0xebe0 [psm 4113]
      I-frame: Start (len 672) TxSeq 0 ReqSeq 0
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

This makes it much easier for the users to understand why the driver
refuses to load when the firmware is unavailable.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

hci_unregister_dev cannot fail and always returns 0. The drivers already ignore
the return value so we can safely make it return void.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Make all bluetooth drivers ignore the return value of hci_unregister_dev as it
always returns 0. In the next step, hci_unregister_dev can be modified to return
void.
Some of the drivers already ignore the return value (including btusb), hence,
this will increase consitency in the bluetooth drivers.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Remove old tasklets and replace by workqueue. To avoid reentrancy (which
tasklets always avoid) we use the system_nrt_wq.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Forward error codes from tty core to the rfcomm_init caller instead of using
generic -1 errors.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Add parsing Extended Flow Specification option in L2CAP Config Request
Based upon haijun.liu <haijun.liu@atheros.com> series of patches
(sent Sun, 22 Aug 2010)
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Fix max_pdu_size calculationin for RFC. Change magic number to human readable
defines.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>