Change type of active_fec to u32 to match the type expected by
mlx5e_get_fec_mode. Copy active_fec and configured_fec values to
unsigned long before preforming bitwise manipulations.
Take the same approach when configuring FEC over 50G link modes: copy
the policy into an unsigned long and only than preform bitwise
operations.

Fixes: 2132b71f ("net/mlx5e: Advertise globaly supported FEC modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

On tunnel decap rule insertion, the indirect mechanism will attempt to
offload the rule on all uplink representors which will trigger the
"devices are not on same switch HW, can't offload forwarding" message
for the uplink which isn't on the same switch HW as the VF representor.

The above flow is valid and shouldn't cause warning message,
fix by removing the warning and only report this flow using extack.

Fixes: 32134847 ("net/mlx5e: Fix allowed tc redirect merged eswitch offload cases")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

It's bytes, packets, lastused.

Fixes: fcb64c0f ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently a Linux system with the mlx5 NIC always crashes upon
hibernation - suspend/resume.

Add basic callbacks so the NIC could be suspended and resumed.

Fixes: 9603b61d ("mlx5: Move pci device handling from mlx5_ib to mlx5_core")
Tested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Recent change in virtio_net_hdr_to_skb() broke some packetdrill tests.

When --mss=XXX option is set, packetdrill always provide gso_type & gso_size
for its inbound packets, regardless of packet size.

	if (packet->tcp && packet->mss) {
		if (packet->ipv4)
			gso.gso_type = VIRTIO_NET_HDR_GSO_TCPV4;
		else
			gso.gso_type = VIRTIO_NET_HDR_GSO_TCPV6;
		gso.gso_size = packet->mss;
	}

Since many other programs could do the same, relax virtio_net_hdr_to_skb()
to no longer return an error, but instead ignore gso settings.

This keeps Willem intent to make sure no malicious packet could
reach gso stack.

Note that TCP stack has a special logic in tcp_set_skb_tso_segs()
to clear gso_size for small packets.

Fixes: 6dd912f8 ("net: check untrusted gso_size at kernel entry")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure SCTP_ADDR_{MADE_PRIM,ADDED} are sent only for associations
that have been established.

These events are described in rfc6458#section-6.1
SCTP_PEER_ADDR_CHANGE:
This tag indicates that an address that is
part of an existing association has experienced a change of
state (e.g., a failure or return to service of the reachability
of an endpoint via a specific transport address).
Signed-off-by: Jonas Falkevik <jonas.falkevik@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kobject_init_and_add() takes reference even when it fails.
If this function returns an error, kobject_put() must be called to
properly clean up the memory associated with the object. Previous
commit "b8eb7183" fixed a similar problem.

Fixes: 07699f9a ("bonding: add sysfs /slave dir for bond slave devices.")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) Uninitialized when used in __nf_conntrack_update(), from
   Nathan Chancellor.

2) Comparison of unsigned expression in nf_confirm_cthelper().

3) Remove 'const' type qualifier with no effect.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Be there a platform with the following layout:

      Regular NIC
       |
       +----> DSA master for switch port
               |
               +----> DSA master for another switch port

After changing DSA back to static lockdep class keys in commit
1a33e10e ("net: partially revert dynamic lockdep key changes"), this
kernel splat can be seen:

[   13.361198] ============================================
[   13.366524] WARNING: possible recursive locking detected
[   13.371851] 5.7.0-rc4-02121-gc32a05ecd7af-dirty #988 Not tainted
[   13.377874] --------------------------------------------
[   13.383201] swapper/0/0 is trying to acquire lock:
[   13.388004] ffff0000668ff298 (&dsa_slave_netdev_xmit_lock_key){+.-.}-{2:2}, at: __dev_queue_xmit+0x84c/0xbe0
[   13.397879]
[   13.397879] but task is already holding lock:
[   13.403727] ffff0000661a1698 (&dsa_slave_netdev_xmit_lock_key){+.-.}-{2:2}, at: __dev_queue_xmit+0x84c/0xbe0
[   13.413593]
[   13.413593] other info that might help us debug this:
[   13.420140]  Possible unsafe locking scenario:
[   13.420140]
[   13.426075]        CPU0
[   13.428523]        ----
[   13.430969]   lock(&dsa_slave_netdev_xmit_lock_key);
[   13.435946]   lock(&dsa_slave_netdev_xmit_lock_key);
[   13.440924]
[   13.440924]  *** DEADLOCK ***
[   13.440924]
[   13.446860]  May be due to missing lock nesting notation
[   13.446860]
[   13.453668] 6 locks held by swapper/0/0:
[   13.457598]  #0: ffff800010003de0 ((&idev->mc_ifc_timer)){+.-.}-{0:0}, at: call_timer_fn+0x0/0x400
[   13.466593]  #1: ffffd4d3fb478700 (rcu_read_lock){....}-{1:2}, at: mld_sendpack+0x0/0x560
[   13.474803]  #2: ffffd4d3fb478728 (rcu_read_lock_bh){....}-{1:2}, at: ip6_finish_output2+0x64/0xb10
[   13.483886]  #3: ffffd4d3fb478728 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x6c/0xbe0
[   13.492793]  #4: ffff0000661a1698 (&dsa_slave_netdev_xmit_lock_key){+.-.}-{2:2}, at: __dev_queue_xmit+0x84c/0xbe0
[   13.503094]  #5: ffffd4d3fb478728 (rcu_read_lock_bh){....}-{1:2}, at: __dev_queue_xmit+0x6c/0xbe0
[   13.512000]
[   13.512000] stack backtrace:
[   13.516369] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.7.0-rc4-02121-gc32a05ecd7af-dirty #988
[   13.530421] Call trace:
[   13.532871]  dump_backtrace+0x0/0x1d8
[   13.536539]  show_stack+0x24/0x30
[   13.539862]  dump_stack+0xe8/0x150
[   13.543271]  __lock_acquire+0x1030/0x1678
[   13.547290]  lock_acquire+0xf8/0x458
[   13.550873]  _raw_spin_lock+0x44/0x58
[   13.554543]  __dev_queue_xmit+0x84c/0xbe0
[   13.558562]  dev_queue_xmit+0x24/0x30
[   13.562232]  dsa_slave_xmit+0xe0/0x128
[   13.565988]  dev_hard_start_xmit+0xf4/0x448
[   13.570182]  __dev_queue_xmit+0x808/0xbe0
[   13.574200]  dev_queue_xmit+0x24/0x30
[   13.577869]  neigh_resolve_output+0x15c/0x220
[   13.582237]  ip6_finish_output2+0x244/0xb10
[   13.586430]  __ip6_finish_output+0x1dc/0x298
[   13.590709]  ip6_output+0x84/0x358
[   13.594116]  mld_sendpack+0x2bc/0x560
[   13.597786]  mld_ifc_timer_expire+0x210/0x390
[   13.602153]  call_timer_fn+0xcc/0x400
[   13.605822]  run_timer_softirq+0x588/0x6e0
[   13.609927]  __do_softirq+0x118/0x590
[   13.613597]  irq_exit+0x13c/0x148
[   13.616918]  __handle_domain_irq+0x6c/0xc0
[   13.621023]  gic_handle_irq+0x6c/0x160
[   13.624779]  el1_irq+0xbc/0x180
[   13.627927]  cpuidle_enter_state+0xb4/0x4d0
[   13.632120]  cpuidle_enter+0x3c/0x50
[   13.635703]  call_cpuidle+0x44/0x78
[   13.639199]  do_idle+0x228/0x2c8
[   13.642433]  cpu_startup_entry+0x2c/0x48
[   13.646363]  rest_init+0x1ac/0x280
[   13.649773]  arch_call_rest_init+0x14/0x1c
[   13.653878]  start_kernel+0x490/0x4bc

Lockdep keys themselves were added in commit ab92d68f ("net: core:
add generic lockdep keys"), and it's very likely that this splat existed
since then, but I have no real way to check, since this stacked platform
wasn't supported by mainline back then.

>From Taehee's own words:

  This patch was considered that all stackable devices have LLTX flag.
  But the dsa doesn't have LLTX, so this splat happened.
  After this patch, dsa shares the same lockdep class key.
  On the nested dsa interface architecture, which you illustrated,
  the same lockdep class key will be used in __dev_queue_xmit() because
  dsa doesn't have LLTX.
  So that lockdep detects deadlock because the same lockdep class key is
  used recursively although actually the different locks are used.
  There are some ways to fix this problem.

  1. using NETIF_F_LLTX flag.
  If possible, using the LLTX flag is a very clear way for it.
  But I'm so sorry I don't know whether the dsa could have LLTX or not.

  2. using dynamic lockdep again.
  It means that each interface uses a separate lockdep class key.
  So, lockdep will not detect recursive locking.
  But this way has a problem that it could consume lockdep class key
  too many.
  Currently, lockdep can have 8192 lockdep class keys.
   - you can see this number with the following command.
     cat /proc/lockdep_stats
     lock-classes:                         1251 [max: 8192]
     ...
     The [max: 8192] means that the maximum number of lockdep class keys.
  If too many lockdep class keys are registered, lockdep stops to work.
  So, using a dynamic(separated) lockdep class key should be considered
  carefully.
  In addition, updating lockdep class key routine might have to be existing.
  (lockdep_register_key(), lockdep_set_class(), lockdep_unregister_key())

  3. Using lockdep subclass.
  A lockdep class key could have 8 subclasses.
  The different subclass is considered different locks by lockdep
  infrastructure.
  But "lock-classes" is not counted by subclasses.
  So, it could avoid stopping lockdep infrastructure by an overflow of
  lockdep class keys.
  This approach should also have an updating lockdep class key routine.
  (lockdep_set_subclass())

  4. Using nonvalidate lockdep class key.
  The lockdep infrastructure supports nonvalidate lockdep class key type.
  It means this lockdep is not validated by lockdep infrastructure.
  So, the splat will not happen but lockdep couldn't detect real deadlock
  case because lockdep really doesn't validate it.
  I think this should be used for really special cases.
  (lockdep_set_novalidate_class())

Further discussion here:
https://patchwork.ozlabs.org/project/netdev/patch/20200503052220.4536-2-xiyou.wangcong@gmail.com/

There appears to be no negative side-effect to declaring lockless TX for
the DSA virtual interfaces, which means they handle their own locking.
So that's what we do to make the splat go away.

Patch tested in a wide variety of cases: unicast, multicast, PTP, etc.

Fixes: ab92d68f ("net: core: add generic lockdep keys")
Suggested-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As explained in other commits before (b9cd75e6 and 87b0f983),
ocelot switches have a single egress-untagged VLAN per port, and the
driver would deny adding a second one while an egress-untagged VLAN
already exists.

But on the CPU port (where the VLAN configuration is implicit, because
there is no net device for the bridge to control), the DSA core attempts
to add a VLAN using the same flags as were used for the front-panel
port. This would make adding any untagged VLAN fail due to the CPU port
rejecting the configuration:

bridge vlan add dev swp0 vid 100 pvid untagged
[ 1865.854253] mscc_felix 0000:00:00.5: Port already has a native VLAN: 1
[ 1865.860824] mscc_felix 0000:00:00.5: Failed to add VLAN 100 to port 5: -16

(note that port 5 is the CPU port and not the front-panel swp0).

So this hardware will send all VLANs as tagged towards the CPU.

Fixes: 56051948 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clang-10 and clang-11 run into a corner case of the register
allocator on 32-bit ARM, leading to excessive stack usage from
register spilling:

net/bridge/br_multicast.c:2422:6: error: stack frame size of 1472 bytes in function 'br_multicast_get_stats' [-Werror,-Wframe-larger-than=]

Work around this by marking one of the internal functions as
noinline_for_stack.

Link: https://bugs.llvm.org/show_bug.cgi?id=45802#c9Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The accept(2) is an "input" socket interface, so we should use
SO_RCVTIMEO instead of SO_SNDTIMEO to set the timeout.

So this patch replace sock_sndtimeo() with sock_rcvtimeo() to
use the right timeout in the vsock_accept().

Fixes: d021c344 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to this change the correct value for the used counter is calculated
but not stored nor, therefore, propagated to user-space. In use-cases such
as OVS use-case at least this results in active flows being removed from
the hardware datapath. Which results in both unnecessary flow tear-down
and setup, and packet processing on the host.

This patch addresses the problem by saving the calculated used value
which allows the value to propagate to user-space.

Found by inspection.

Fixes: aa6ce2ea ("nfp: flower: support stats update for merge flows")
Signed-off-by: Heinrich Kuhn <heinrich.kuhn@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

this command hangs forever:

 # tc qdisc add dev eth0 root fq_pie flows 65536

 watchdog: BUG: soft lockup - CPU#1 stuck for 23s! [tc:1028]
 [...]
 CPU: 1 PID: 1028 Comm: tc Not tainted 5.7.0-rc6+ #167
 RIP: 0010:fq_pie_init+0x60e/0x8b7 [sch_fq_pie]
 Code: 4c 89 65 50 48 89 f8 48 c1 e8 03 42 80 3c 30 00 0f 85 2a 02 00 00 48 8d 7d 10 4c 89 65 58 48 89 f8 48 c1 e8 03 42 80 3c 30 00 <0f> 85 a7 01 00 00 48 8d 7d 18 48 c7 45 10 46 c3 23 00 48 89 f8 48
 RSP: 0018:ffff888138d67468 EFLAGS: 00000246 ORIG_RAX: ffffffffffffff13
 RAX: 1ffff9200018d2b2 RBX: ffff888139c1c400 RCX: ffffffffffffffff
 RDX: 000000000000c5e8 RSI: ffffc900000e5000 RDI: ffffc90000c69590
 RBP: ffffc90000c69580 R08: fffffbfff79a9699 R09: fffffbfff79a9699
 R10: 0000000000000700 R11: fffffbfff79a9698 R12: ffffc90000c695d0
 R13: 0000000000000000 R14: dffffc0000000000 R15: 000000002347c5e8
 FS:  00007f01e1850e40(0000) GS:ffff88814c880000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 000000000067c340 CR3: 000000013864c000 CR4: 0000000000340ee0
 Call Trace:
  qdisc_create+0x3fd/0xeb0
  tc_modify_qdisc+0x3be/0x14a0
  rtnetlink_rcv_msg+0x5f3/0x920
  netlink_rcv_skb+0x121/0x350
  netlink_unicast+0x439/0x630
  netlink_sendmsg+0x714/0xbf0
  sock_sendmsg+0xe2/0x110
  ____sys_sendmsg+0x5b4/0x890
  ___sys_sendmsg+0xe9/0x160
  __sys_sendmsg+0xd3/0x170
  do_syscall_64+0x9a/0x370
  entry_SYSCALL_64_after_hwframe+0x44/0xa9

we can't accept 65536 as a valid number for 'nflows', because the loop on
'idx' in fq_pie_init() will never end. The extack message is correct, but
it doesn't say that 0 is not a valid number for 'flows': while at it, fix
this also. Add a tdc selftest to check correct validation of 'flows'.

CC: Ivan Vecera <ivecera@redhat.com>
Fixes: ec97ecf1 ("net: sched: add Flow Queue PIE packet scheduler")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

>> include/linux/netfilter/nf_conntrack_pptp.h:13:20: warning: 'const' type qualifier on return type has no effect [-Wignored-qualifiers]
extern const char *const pptp_msg_name(u_int16_t msg);
^~~~~~
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 4c559f15 ("netfilter: nf_conntrack_pptp: prevent buffer overflows in debug code")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

net/netfilter/nf_conntrack_core.c: In function nf_confirm_cthelper:
net/netfilter/nf_conntrack_core.c:2117:15: warning: comparison of unsigned expression in < 0 is always false [-Wtype-limits]
 2117 |   if (protoff < 0 || (frag_off & htons(~0x7)) != 0)
      |               ^

ipv6_skip_exthdr() returns a signed integer.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 703acd70 ("netfilter: nfnetlink_cthelper: unbreak userspace helper support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Clang warns:

net/netfilter/nf_conntrack_core.c:2068:21: warning: variable 'ctinfo' is
uninitialized when used here [-Wuninitialized]
        nf_ct_set(skb, ct, ctinfo);
                           ^~~~~~
net/netfilter/nf_conntrack_core.c:2024:2: note: variable 'ctinfo' is
declared here
        enum ip_conntrack_info ctinfo;
        ^
1 warning generated.

nf_conntrack_update was split up into nf_conntrack_update and
__nf_conntrack_update, where the assignment of ctinfo is in
nf_conntrack_update but it is used in __nf_conntrack_update.

Pass the value of ctinfo from nf_conntrack_update to
__nf_conntrack_update so that uninitialized memory is not used
and everything works properly.

Fixes: ee04805f ("netfilter: conntrack: make conntrack userspace helpers work again")
Link: https://github.com/ClangBuiltLinux/linux/issues/1039Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

TCP tp->lsndtime unit/base is tcp_jiffies32, not tcp_time_stamp()

Fixes: 36bedb3f ("crypto: chtls - Inline TLS record Tx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ayush Sawal <ayush.sawal@chelsio.com>
Cc: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change 'handeled' to 'handled' in the Kconfig help for SCTP.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Bug fixes.

3 bnxt_en driver fixes, covering a bug in preserving the counters during
some resets, proper error code when flashing NVRAM fails, and an
endian bug when extracting the firmware response message length.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The explicit mask and shift is not the appropriate way to parse fields
out of a little endian struct. The length field is internally __le16
and the strategy employed only happens to work on little endian machines
because the offset used is actually incorrect (length is at offset 6).

Also remove the related and no longer used definitions from bnxt.h.

Fixes: 845adfe4 ("bnxt_en: Improve valid bit checking in firmware response message.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When NVRAM directory is not found, return the error code
properly as per firmware command failure instead of the hardcode
-ENOBUFS.

Fixes: 3a707bed ("bnxt_en: Return -EAGAIN if fw command returns BUSY")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have logic to maintain network counters across resets by storing
the counters in bp->net_stats_prev before reset.  But not all resets
will clear the counters.  Certain resets that don't need to change
the number of rings do not clear the counters.  The current logic
accumulates the counters before all resets, causing big jumps in
the counters after some resets, such as ethtool -G.

Fix it by only accumulating the counters during reset if the irq_re_init
parameter is set.  The parameter signifies that all rings and interrupts
will be reset and that means that the counters will also be reset.
Reported-by: Vijayendra Suman <vijayendra.suman@oracle.com>
Fixes: b8875ca3 ("bnxt_en: Save ring statistics before reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for Telit LE910C1-EUX composition

0x1031: tty, tty, tty, rmnet
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Syzkaller again found a path to a kernel crash through bad gso input:
a packet with gso size exceeding len.

These packets are dropped in tcp_gso_segment and udp[46]_ufo_fragment.
But they may affect gso size calculations earlier in the path.

Now that we have thlen as of commit 9274124f ("net: stricter
validation of untrusted gso packets"), check gso_size at entry too.

Fixes: bfd5f4a3 ("packet: Add GSO/csum offload support.")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the MPTCP receive path we must cope with TCP fallback
on blocking recvmsg(). Currently in such code path we detect
the fallback condition, but we don't fetch the struct socket
required for fallback.

The above allowed syzkaller to trigger a NULL pointer
dereference:

general protection fault, probably for non-canonical address 0xdffffc0000000004: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000020-0x0000000000000027]
CPU: 1 PID: 7226 Comm: syz-executor523 Not tainted 5.7.0-rc6-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:sock_recvmsg_nosec net/socket.c:886 [inline]
RIP: 0010:sock_recvmsg+0x92/0x110 net/socket.c:904
Code: 5b 41 5c 41 5d 41 5e 41 5f 5d c3 44 89 6c 24 04 e8 53 18 1d fb 4d 8d 6f 20 4c 89 e8 48 c1 e8 03 48 b9 00 00 00 00 00 fc ff df <80> 3c 08 00 74 08 4c 89 ef e8 20 12 5b fb bd a0 00 00 00 49 03 6d
RSP: 0018:ffffc90001077b98 EFLAGS: 00010202
RAX: 0000000000000004 RBX: ffffc90001077dc0 RCX: dffffc0000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: ffffffff86565e59 R09: ffffed10115afeaa
R10: ffffed10115afeaa R11: 0000000000000000 R12: 1ffff9200020efbc
R13: 0000000000000020 R14: ffffc90001077de0 R15: 0000000000000000
FS:  00007fc6a3abe700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004d0050 CR3: 00000000969f0000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 mptcp_recvmsg+0x18d5/0x19b0 net/mptcp/protocol.c:891
 inet_recvmsg+0xf6/0x1d0 net/ipv4/af_inet.c:838
 sock_recvmsg_nosec net/socket.c:886 [inline]
 sock_recvmsg net/socket.c:904 [inline]
 __sys_recvfrom+0x2f3/0x470 net/socket.c:2057
 __do_sys_recvfrom net/socket.c:2075 [inline]
 __se_sys_recvfrom net/socket.c:2071 [inline]
 __x64_sys_recvfrom+0xda/0xf0 net/socket.c:2071
 do_syscall_64+0xf3/0x1b0 arch/x86/entry/common.c:295
 entry_SYSCALL_64_after_hwframe+0x49/0xb3

Address the issue initializing the struct socket reference
before entering the fallback code.

Reported-and-tested-by: syzbot+c6bfc3db991edc918432@syzkaller.appspotmail.com
Suggested-by: Ondrej Mosnacek <omosnace@redhat.com>
Fixes: 8ab183de ("mptcp: cope with later TCP fallback")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For rx filter 'HWTSTAMP_FILTER_PTP_V2_EVENT', it should be
PTP v2/802.AS1, any layer, any kind of event packet, but HW only
take timestamp snapshot for below PTP message: sync, Pdelay_req,
Pdelay_resp.

Then it causes below issue when test E2E case:
ptp4l[2479.534]: port 1: received DELAY_REQ without timestamp
ptp4l[2481.423]: port 1: received DELAY_REQ without timestamp
ptp4l[2481.758]: port 1: received DELAY_REQ without timestamp
ptp4l[2483.524]: port 1: received DELAY_REQ without timestamp
ptp4l[2484.233]: port 1: received DELAY_REQ without timestamp
ptp4l[2485.750]: port 1: received DELAY_REQ without timestamp
ptp4l[2486.888]: port 1: received DELAY_REQ without timestamp
ptp4l[2487.265]: port 1: received DELAY_REQ without timestamp
ptp4l[2487.316]: port 1: received DELAY_REQ without timestamp

Timestamp snapshot dependency on register bits in received path:
SNAPTYPSEL TSMSTRENA TSEVNTENA 	PTP_Messages
01         x         0          SYNC, Follow_Up, Delay_Req,
                                Delay_Resp, Pdelay_Req, Pdelay_Resp,
                                Pdelay_Resp_Follow_Up
01         0         1          SYNC, Pdelay_Req, Pdelay_Resp

For dwmac v5.10a, enabling all events by setting register
DWC_EQOS_TIME_STAMPING[SNAPTYPSEL] to 2’b01, clearing bit [TSEVNTENA]
to 0’b0, which can support all required events.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Ahern says:

====================
nexthops: Fix 2 fundamental flaws with nexthop groups

Nik's torture tests have exposed 2 fundamental mistakes with the initial
nexthop code for groups. First, the nexthops entries and num_nh in the
nh_grp struct should not be modified once the struct is set under rcu.
Doing so has major affects on the datapath seeing valid nexthop entries.

Second, the helpers in the header file were convenient for not repeating
code, but they cause datapath walks to potentially see 2 different group
structs after an rcu replace, disrupting a walk of the path objects.
This second problem applies solely to IPv4 as I re-used too much of the
existing code in walking legs of a multipath route.

Patches 1 is refactoring change to simplify the overhead of reviewing and
understanding the change in patch 2 which fixes the update of nexthop
groups when a compnent leg is removed.

Patches 3-5 address the second problem. Patch 3 inlines the multipath
check such that the mpath lookup and subsequent calls all use the same
nh_grp struct. Patches 4 and 5 fix datapath uses of fib_info_num_path
with iterative calls to fib_info_nhc.

fib_info_num_path can be used in control plane path in a 'for loop' with
subsequent fib_info_nhc calls to get each leg since the nh_grp struct is
only changed while holding the rtnl; the combination can not be used in
the data plane with external nexthops as it involves repeated dereferences
of nh_grp struct which can change between calls.

Similarly, nexthop_is_multipath can be used for branching decisions in
the datapath since the nexthop type can not be changed (a group can not
be converted to standalone and vice versa).

Patch set developed in coordination with Nikolay Aleksandrov. He did a
lot of work creating a good reproducer, discussing options to fix it
and testing iterations.

I have adapted Nik's commands into additional tests in the nexthops
selftest script which I will send against -next.

v2
- fixed whitespace errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the last path, need to fix fib_info_nh_uses_dev for
external nexthops to avoid referencing multiple nh_grp structs.
Move the device check in fib_info_nh_uses_dev to a helper and
create a nexthop version that is called if the fib_info uses an
external nexthop.

Fixes: 430a0491 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FIB lookups can return an entry that references an external nexthop.
While walking the nexthop struct we do not want to make multiple calls
into the nexthop code which can result in 2 different structs getting
accessed - one returning the number of paths the rest of the loop
seeing a different nh_grp struct. If the nexthop group shrunk, the
result is an attempt to access a fib_nh_common that does not exist for
the new nh_grp struct but did for the old one.

To fix that move the device evaluation code to a helper that can be
used for inline fib_nh path as well as external nexthops.

Update the existing check for fi->nh in fib_table_lookup to call a
new helper, nexthop_get_nhc_lookup, which walks the external nexthop
with a single rcu dereference.

Fixes: 430a0491 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I got too fancy consolidating checks on multipath type. The result
is that path lookups can access 2 different nh_grp structs as exposed
by Nik's torture tests. Expand nexthop_is_multipath within nexthop.h to
avoid multiple, nh_grp dereferences and make decisions based on the
consistent struct.

Only 2 places left using nexthop_is_multipath are within IPv6, both
only check that the nexthop is a multipath for a branching decision
which are acceptable.

Fixes: 430a0491 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We must avoid modifying published nexthop groups while they might be
in use, otherwise we might see NULL ptr dereferences. In order to do
that we allocate 2 nexthoup group structures upon nexthop creation
and swap between them when we have to delete an entry. The reason is
that we can't fail nexthop group removal, so we can't handle allocation
failure thus we move the extra allocation on creation where we can
safely fail and return ENOMEM.

Fixes: 430a0491 ("nexthop: Add support for nexthop groups")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move nh_grp dereference and check for removing nexthop group due to
all members gone into remove_nh_grp_entry.

Fixes: 430a0491 ("nexthop: Add support for nexthop groups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) Set VLAN tag in tcp reset/icmp unreachable packets to reject
   connections in the bridge family, from Michael Braun.

2) Incorrect subcounter flag update in ipset, from Phil Sutter.

3) Possible buffer overflow in the pptp conntrack helper, based
   on patch from Dan Carpenter.

4) Restore userspace conntrack helper hook logic that broke after
   hook consolidation rework.

5) Unbreak userspace conntrack helper registration via
   nfnetlink_cthelper.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-net-2020-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
A few changes:
 * fix a debugfs vs. wiphy rename crash
 * fix an invalid HE spec definition
 * fix a mesh timer crash
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In function qlcnic_83xx_interrupt_test(), function
qlcnic_83xx_diag_alloc_res() is not handled by function
qlcnic_83xx_diag_free_res() after a call of the function
qlcnic_alloc_mbx_args() failed. Fix this issue by adding
a jump target "fail_mbx_args", and jump to this new target
when qlcnic_alloc_mbx_args() failed.

Fixes: b6b4316c ("qlcnic: Handle qlcnic_alloc_mbx_args() failure")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dpaa-eth driver probes on compatible string for the MAC node, and
the fman/mac.c driver allocates a dpaa-ethernet platform device that
triggers the probing of the dpaa-eth net device driver.

All of this is fine, but the problem is that the struct device of the
dpaa_eth net_device is 2 parents away from the MAC which can be
referenced via of_node. So of_find_net_device_by_node can't find it, and
DSA switches won't be able to probe on top of FMan ports.

It would be a bit silly to modify a core function
(of_find_net_device_by_node) to look for dev->parent->parent->of_node
just for one driver. We're just 1 step away from implementing full
recursion.

Actually there have already been at least 2 previous attempts to make
this work:
- Commit a1a50c8e ("fsl/man: Inherit parent device and of_node")
- One or more of the patches in "[v3,0/6] adapt DPAA drivers for DSA":
  https://patchwork.ozlabs.org/project/netdev/cover/1508178970-28945-1-git-send-email-madalin.bucur@nxp.com/
  (I couldn't really figure out which one was supposed to solve the
  problem and how).

Point being, it looks like this is still pretty much a problem today.
On T1040, the /sys/class/net/eth0 symlink currently points to

../../devices/platform/ffe000000.soc/ffe400000.fman/ffe4e6000.ethernet/dpaa-ethernet.0/net/eth0

which pretty much illustrates the problem. The closest of_node we've got
is the "fsl,fman-memac" at /soc@ffe000000/fman@400000/ethernet@e6000,
which is what we'd like to be able to reference from DSA as host port.

For of_find_net_device_by_node to find the eth0 port, we would need the
parent of the eth0 net_device to not be the "dpaa-ethernet" platform
device, but to point 1 level higher, aka the "fsl,fman-memac" node
directly. The new sysfs path would look like this:

../../devices/platform/ffe000000.soc/ffe400000.fman/ffe4e6000.ethernet/net/eth0

And this is exactly what SET_NETDEV_DEV does. It sets the parent of the
net_device. The new parent has an of_node associated with it, and
of_dev_node_match already checks for the of_node of the device or of its
parent.

Fixes: a1a50c8e ("fsl/man: Inherit parent device and of_node")
Fixes: c6e26ea8 ("dpaa_eth: change device used")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tls_sw_recvmsg() and tls_decrypt_done() can be run concurrently.
// tls_sw_recvmsg()
	if (atomic_read(&ctx->decrypt_pending))
		crypto_wait_req(-EINPROGRESS, &ctx->async_wait);
	else
		reinit_completion(&ctx->async_wait.completion);

//tls_decrypt_done()
  	pending = atomic_dec_return(&ctx->decrypt_pending);

  	if (!pending && READ_ONCE(ctx->async_notify))
  		complete(&ctx->async_wait.completion);

Consider the scenario tls_decrypt_done() is about to run complete()

	if (!pending && READ_ONCE(ctx->async_notify))

and tls_sw_recvmsg() reads decrypt_pending == 0, does reinit_completion(),
then tls_decrypt_done() runs complete(). This sequence of execution
results in wrong completion. Consequently, for next decrypt request,
it will not wait for completion, eventually on connection close, crypto
resources freed, there is no way to handle pending decrypt response.

This race condition can be avoided by having atomic_read() mutually
exclusive with atomic_dec_return(),complete().Intoduced spin lock to
ensure the mutual exclution.

Addressed similar problem in tx direction.

v1->v2:
- More readable commit message.
- Corrected the lock to fix new race scenario.
- Removed barrier which is not needed now.

Fixes: a42055e8 ("net/tls: Add support for async encryption of records for performance")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Restore helper data size initialization and fix memcopy of the helper
data size.

Fixes: 157ffffe ("netfilter: nfnetlink_cthelper: reject too large userspace allocation requests")
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Florian Westphal says:

"Problem is that after the helper hook was merged back into the confirm
one, the queueing itself occurs from the confirm hook, i.e. we queue
from the last netfilter callback in the hook-list.

Therefore, on return, the packet bypasses the confirm action and the
connection is never committed to the main conntrack table.

To fix this there are several ways:
1. revert the 'Fixes' commit and have a extra helper hook again.
   Works, but has the drawback of adding another indirect call for
   everyone.

2. Special case this: split the hooks only when userspace helper
   gets added, so queueing occurs at a lower priority again,
   and normal enqueue reinject would eventually call the last hook.

3. Extend the existing nf_queue ct update hook to allow a forced
   confirmation (plus run the seqadj code).

This goes for 3)."

Fixes: 827318fe ("netfilter: conntrack: remove helper hook again")
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>