batman tries to search dev->iflink to check if it's a batman interface,
but ->iflink could be 0, which is not a valid ifindex. It should just
avoid iflink == 0 case.
Reported-by: Jet Chen <jet.chen@intel.com>
Tested-by: Jet Chen <jet.chen@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Antonio Quartulli <antonio@open-mesh.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the value of itag is a random value from stack, and may not be initiated by
fib_validate_source, which called fib_combine_itag if CONFIG_IP_ROUTE_CLASSID
is not set

This will make the cached dst uncertainty
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ALB learning packets are currentlyalways sent using the slave mac
address for all vlans configured on top of bond.   This is not always
correct, as vlans may change their mac address.
This patch introduced a concept of strict matching where the
source of learning packets can either strictly match the address
passed in, or it can determine a more correct address to use.

There are 3 casese to consider:
  1) Switchover.  In this case, we have a new active slave and we need
     tell the switch about all addresses available on the slave.
  2) Monitor.  We'll periodically refresh learning info for all slaves.
     In this case, we refresh all addresses for current active, and just
     the slave address for other slaves.
  3) Teaching of disabled adddress.  This happens as part of the
     failover and in this case, we alwyas to use just the address
     provided.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TLB/ALB learning packets always assume 802.1Q vlan protocol, but
that is no longer the case since we now have support for Q-in-Q
on top of bonding.  Pass the vlan protocol to alb_send_lp_vid()
so that the packets are properly tagged.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
pull-request: can 2014-05-21

this is a pull request for net/master, for the v3.15 release cycle, with a
single patch. Christopher R. Baker found a use after free during unloading of
the peak_pci driver. This is fixes in a patch by Stephane Grosjean.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 61b905da ("net: Rename skb->rxhash to skb->hash"), skb->rxhash
was renamed to skb->hash. Update references in Documentation
accordingly.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The stmmac_open call was calling clk_disable_unprepare on phy init
failure, but it never calls clk_prepare_enable, this causes
a WARN_ON in the clk framework to trigger if for some reason phy init
fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When GRE support was added in linux-3.14, CHECKSUM_COMPLETE handling
broke on GRE+IPv6 because we did not update/use the appropriate csum :

GRO layer is supposed to use/update NAPI_GRO_CB(skb)->csum instead of
skb->csum

Tested using a GRE tunnel and IPv6 traffic. GRO aggregation now happens
at the first level (ethernet device) instead of being done in gre
tunnel. Native IPv6+TCP is still properly aggregated.

Fixes: bf5a755f ("net-gre-gro: Add GRE support to the GRO stack")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kelly reported the following crash:

        IP: [<ffffffff817a993d>] tcf_action_exec+0x46/0x90
        PGD 3009067 PUD 300c067 PMD 11ff30067 PTE 800000011634b060
        Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
        CPU: 1 PID: 639 Comm: dhclient Not tainted 3.15.0-rc4+ #342
        Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
        task: ffff8801169ecd00 ti: ffff8800d21b8000 task.ti: ffff8800d21b8000
        RIP: 0010:[<ffffffff817a993d>]  [<ffffffff817a993d>] tcf_action_exec+0x46/0x90
        RSP: 0018:ffff8800d21b9b90  EFLAGS: 00010283
        RAX: 00000000ffffffff RBX: ffff88011634b8e8 RCX: ffff8800cf7133d8
        RDX: ffff88011634b900 RSI: ffff8800cf7133e0 RDI: ffff8800d210f840
        RBP: ffff8800d21b9bb0 R08: ffffffff8287bf60 R09: 0000000000000001
        R10: ffff8800d2b22b24 R11: 0000000000000001 R12: ffff8800d210f840
        R13: ffff8800d21b9c50 R14: ffff8800cf7133e0 R15: ffff8800cad433d8
        FS:  00007f49723e1840(0000) GS:ffff88011a800000(0000) knlGS:0000000000000000
        CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
        CR2: ffff88011634b8f0 CR3: 00000000ce469000 CR4: 00000000000006e0
        Stack:
         ffff8800d2170188 ffff8800d210f840 ffff8800d2171b90 0000000000000000
         ffff8800d21b9be8 ffffffff817c55bb ffff8800d21b9c50 ffff8800d2171b90
         ffff8800d210f840 ffff8800d21b0300 ffff8800d21b9c50 ffff8800d21b9c18
        Call Trace:
         [<ffffffff817c55bb>] tcindex_classify+0x88/0x9b
         [<ffffffff817a7f7d>] tc_classify_compat+0x3e/0x7b
         [<ffffffff817a7fdf>] tc_classify+0x25/0x9f
         [<ffffffff817b0e68>] htb_enqueue+0x55/0x27a
         [<ffffffff817b6c2e>] dsmark_enqueue+0x165/0x1a4
         [<ffffffff81775642>] __dev_queue_xmit+0x35e/0x536
         [<ffffffff8177582a>] dev_queue_xmit+0x10/0x12
         [<ffffffff818f8ecd>] packet_sendmsg+0xb26/0xb9a
         [<ffffffff810b1507>] ? __lock_acquire+0x3ae/0xdf3
         [<ffffffff8175cf08>] __sock_sendmsg_nosec+0x25/0x27
         [<ffffffff8175d916>] sock_aio_write+0xd0/0xe7
         [<ffffffff8117d6b8>] do_sync_write+0x59/0x78
         [<ffffffff8117d84d>] vfs_write+0xb5/0x10a
         [<ffffffff8117d96a>] SyS_write+0x49/0x7f
         [<ffffffff8198e212>] system_call_fastpath+0x16/0x1b

This is because we memcpy struct tcindex_filter_result which contains
struct tcf_exts, obviously struct list_head can not be simply copied.
This is a regression introduced by commit 33be6271
(net_sched: act: use standard struct list_head).

It's not very easy to fix it as the code is a mess:

       if (old_r)
               memcpy(&cr, r, sizeof(cr));
       else {
               memset(&cr, 0, sizeof(cr));
               tcf_exts_init(&cr.exts, TCA_TCINDEX_ACT, TCA_TCINDEX_POLICE);
       }
       ...
       tcf_exts_change(tp, &cr.exts, &e);
       ...
       memcpy(r, &cr, sizeof(cr));

the above code should equal to:

        tcindex_filter_result_init(&cr);
        if (old_r)
               cr.res = r->res;
        ...
        if (old_r)
               tcf_exts_change(tp, &r->exts, &e);
        else
               tcf_exts_change(tp, &cr.exts, &e);
        ...
        r->res = cr.res;

after this change, since there is no need to copy struct tcf_exts.

And it also fixes other places zero'ing struct's contains struct tcf_exts.

Fixes: commit 33be6271 (net_sched: act: use standard struct list_head)
Reported-by: Kelly Anderson <kelly@xilka.com>
Tested-by: Kelly Anderson <kelly@xilka.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As remarked by Christopher R. Baker in his post at

http://marc.info/?l=linux-can&m=139707295706465&w=2

there's a possibility for an use after free condition at device removal.

This simplified patch introduces an additional variable to prevent the issue.
Thanks for catching this.

Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Christopher R. Baker <cbaker@rec.ri.cmu.edu>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

We need to initialize the fallback device to have a correct mtu
set on this device. Otherwise the mtu is set to null and the device
is unusable.

Fixes: fd58156e ("IPIP: Use ip-tunneling code.")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
pull-request: can 2014-05-19

this is a pull request for net/master, for the v3.15 release cycle,
with a single patch.

Oliver Hartkopp's patch removes a Kconfig option in the c_can driver,
which was added as a workaround during the v3.15 development. With all
cleanup patches this workaround is not needed anymore.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/nftables fixes for net

The following patchset contains nftables fixes for your net tree, they
are:

1) Fix crash when using the goto action in a rule by making sure that
   we always fall back on the base chain. Otherwise, this may try to
   access the counter memory area of non-base chains, which does not
   exists.

2) Fix several aspects of the rule tracing that are currently broken:

   * Reset rule number counter after goto/jump action, otherwise the
     tracing reports a bogus rule number.
   * Fix tracing of the goto action.
   * Fix bogus rule number counter after goto.
   * Fix missing return trace after finishing the walk through the
     non-base chain.
   * Fix missing trace when matching non-terminal rule.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The new function vlan_get_encap_level() uses vlan_dev_priv()
which is only conditionally avaialble when VLAN support is
enabled.  Make vlan_get_encap_level() conditionally available
as well.

Fixes: 44a40855 ("bonding: Fix stacked device detection in arp monitoring")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In 2b9aecdc ("can: c_can: Disable rx split as workaround") a new Kconfig
option was introduced as a workaround. The tests performed by Alexander Stein
confirmed this option to be obsolete with all the other cleanups and fixes
that had been discussed that time:
http://marc.info/?l=linux-can&m=139746476821294&w=2

Both (author and tester) agreed to remove this Kconfig option again:
http://marc.info/?l=linux-can&m=139883820714229&w=2

As some more cleanups took place since then a simple revert is not possible.
This patch removes the entire option as it would behave when disabled.
Further beautification’s can be done later.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pravin will be maintaining Open vSwitch going forward.

CC: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These "return 0;" uses seem wrong as there are
rc variables where error return values are set
but unused.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad Yasevich says:

====================
Fixed stacked vlan usage on top of bonds

Bonding device driver now support q-in-q on top for bonds.  There are
a few issues here though.

First, when arp monitoring is used, bonding driver will not correctly
tag traffic if the source of the arp device was configured on top of
q-in-q.  It may also incorrectly pick the wrong vlan id if the ordering
of that upper devices isn't as expected (there is no guarntee on ordering).

Second, the alb/tlb may use what would be considered 'inner' vlans in
its learning announcements, as it simply announces all vlans configured
on top of the bond without regard for encapsulation/stacking.

This series fixes the above 2 issues.  This series also depends on the
functionality introduced in
	http://patchwork.ozlabs.org/patch/349766/

Since v1:
  - Changed how patch1 verifies the device path.  We no longer use the
    _all_upper version of the function.  We find the path and if it was
    found, then collect the vlan information.
  - Use the constant to devine maximum vlan nest level support on top
    of bonding.  This can be changed if 2 is too low.
  - Inlude patch2 into the series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ALB/TLB learning packets use all vlans configured on top
of the bond.  This ends up being incorrect if we have a stack
of vlans on top of the bond.  ALB/TLB should only use
first level/outer most vlans in its announcements.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to commit fbd929f2
	bonding: support QinQ for bond arp interval

the arp monitoring code allowed for proper detection of devices
stacked on top of vlans.  Since the above commit, the
code can still detect a device stacked on top of single
vlan, but not a device stacked on top of Q-in-Q configuration.
The search will only set the inner vlan tag if the route
device is the vlan device.  However, this is not always the
case, as it is possible to extend the stacked configuration.

With this patch it is possible to provision devices on
top Q-in-Q vlan configuration that should be used as
a source of ARP monitoring information.

For example:
ip link add link bond0 vlan10 type vlan proto 802.1q id 10
ip link add link vlan10 vlan100 type vlan proto 802.1q id 100
ip link add link vlan100 type macvlan

Note:  This patch limites the number of stacked VLANs to 2,
just like before.  The original, however had another issue
in that if we had more then 2 levels of VLANs, we would end
up generating incorrectly tagged traffic.  This is no longer
possible.

Fixes: fbd929f2 (bonding: support QinQ for bond arp interval)
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@redhat.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Patric McHardy <kaber@trash.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vlad Yasevich says:

====================
Fix lockdep issues with stacked devices

Recent commit dc8eaaa0
    vlan: Fix lockdep warning when vlan dev handle notification

attempted to solve lockdep issues with vlans where multiple
vlans were stacked.  However, the code does not work correctly
when the vlan stack is interspersed with other devices in between
the vlans.  Additionally, similar lockdep issues show up with other
devices.

This series provides a generic way to solve these issue for any
devices that can be stacked.  It also addresses the concern for
vlan and macvlan devices.  I am not sure whether it makes sense
to do so for other types like team, vxlan, and bond.

Thanks
-vlad

Since v2:
  - Remove rcu variants from patch1, since that function is called
    only under rtnl.
  - Fix whitespace problems reported by checkpatch

Since v1:
  - Fixed up a goofed-up rebase.
    * is_vlan_dev() should be bool and that change belongs in patch3.
    * patch4 should not have any vlan changes in it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Macvlan devices try to avoid stacking, but that's not always
successfull or even desired.  As an example, the following
configuration is perefectly legal and valid:

eth0 <--- macvlan0 <---- vlan0.10 <--- macvlan1

However, this configuration produces the following lockdep
trace:
[  115.620418] ======================================================
[  115.620477] [ INFO: possible circular locking dependency detected ]
[  115.620516] 3.15.0-rc1+ #24 Not tainted
[  115.620540] -------------------------------------------------------
[  115.620577] ip/1704 is trying to acquire lock:
[  115.620604]  (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[  115.620686]
but task is already holding lock:
[  115.620723]  (&macvlan_netdev_addr_lock_key){+.....}, at: [<ffffffff815da5be>] dev_set_rx_mode+0x1e/0x40
[  115.620795]
which lock already depends on the new lock.

[  115.620853]
the existing dependency chain (in reverse order) is:
[  115.620894]
-> #1 (&macvlan_netdev_addr_lock_key){+.....}:
[  115.620935]        [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[  115.620974]        [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[  115.621019]        [<ffffffffa07296c3>] vlan_dev_set_rx_mode+0x53/0x110 [8021q]
[  115.621066]        [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[  115.621105]        [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[  115.621143]        [<ffffffff815da6be>] __dev_open+0xde/0x140
[  115.621174]        [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[  115.621174]        [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[  115.621174]        [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[  115.621174]        [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[  115.621174]        [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[  115.621174]        [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[  115.621174]        [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[  115.621174]        [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[  115.621174]        [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[  115.621174]        [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[  115.621174]        [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[  115.621174]        [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[  115.621174]        [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[  115.621174]        [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b
[  115.621174]
-> #0 (&vlan_netdev_addr_lock_key/1){+.....}:
[  115.621174]        [<ffffffff810d4d43>] __lock_acquire+0x1773/0x1a60
[  115.621174]        [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[  115.621174]        [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[  115.621174]        [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[  115.621174]        [<ffffffffa0696d2a>] macvlan_set_mac_lists+0xca/0x110 [macvlan]
[  115.621174]        [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[  115.621174]        [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[  115.621174]        [<ffffffff815da6be>] __dev_open+0xde/0x140
[  115.621174]        [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[  115.621174]        [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[  115.621174]        [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[  115.621174]        [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[  115.621174]        [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[  115.621174]        [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[  115.621174]        [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[  115.621174]        [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[  115.621174]        [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[  115.621174]        [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[  115.621174]        [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[  115.621174]        [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[  115.621174]        [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[  115.621174]        [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b
[  115.621174]
other info that might help us debug this:

[  115.621174]  Possible unsafe locking scenario:

[  115.621174]        CPU0                    CPU1
[  115.621174]        ----                    ----
[  115.621174]   lock(&macvlan_netdev_addr_lock_key);
[  115.621174]                                lock(&vlan_netdev_addr_lock_key/1);
[  115.621174]                                lock(&macvlan_netdev_addr_lock_key);
[  115.621174]   lock(&vlan_netdev_addr_lock_key/1);
[  115.621174]
 *** DEADLOCK ***

[  115.621174] 2 locks held by ip/1704:
[  115.621174]  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff815e6dbb>] rtnetlink_rcv+0x1b/0x40
[  115.621174]  #1:  (&macvlan_netdev_addr_lock_key){+.....}, at: [<ffffffff815da5be>] dev_set_rx_mode+0x1e/0x40
[  115.621174]
stack backtrace:
[  115.621174] CPU: 3 PID: 1704 Comm: ip Not tainted 3.15.0-rc1+ #24
[  115.621174] Hardware name: Hewlett-Packard HP xw8400 Workstation/0A08h, BIOS 786D5 v02.38 10/25/2010
[  115.621174]  ffffffff82339ae0 ffff880465f79568 ffffffff816ee20c ffffffff82339ae0
[  115.621174]  ffff880465f795a8 ffffffff816e9e1b ffff880465f79600 ffff880465b019c8
[  115.621174]  0000000000000001 0000000000000002 ffff880465b019c8 ffff880465b01230
[  115.621174] Call Trace:
[  115.621174]  [<ffffffff816ee20c>] dump_stack+0x4d/0x66
[  115.621174]  [<ffffffff816e9e1b>] print_circular_bug+0x200/0x20e
[  115.621174]  [<ffffffff810d4d43>] __lock_acquire+0x1773/0x1a60
[  115.621174]  [<ffffffff810d3172>] ? trace_hardirqs_on_caller+0xb2/0x1d0
[  115.621174]  [<ffffffff810d57f2>] lock_acquire+0xa2/0x130
[  115.621174]  [<ffffffff815df49c>] ? dev_uc_sync+0x3c/0x80
[  115.621174]  [<ffffffff816f62e7>] _raw_spin_lock_nested+0x37/0x50
[  115.621174]  [<ffffffff815df49c>] ? dev_uc_sync+0x3c/0x80
[  115.621174]  [<ffffffff815df49c>] dev_uc_sync+0x3c/0x80
[  115.621174]  [<ffffffffa0696d2a>] macvlan_set_mac_lists+0xca/0x110 [macvlan]
[  115.621174]  [<ffffffff815da557>] __dev_set_rx_mode+0x57/0xa0
[  115.621174]  [<ffffffff815da5c6>] dev_set_rx_mode+0x26/0x40
[  115.621174]  [<ffffffff815da6be>] __dev_open+0xde/0x140
[  115.621174]  [<ffffffff815da9ad>] __dev_change_flags+0x9d/0x170
[  115.621174]  [<ffffffff815daaa9>] dev_change_flags+0x29/0x60
[  115.621174]  [<ffffffff811e1db1>] ? mem_cgroup_bad_page_check+0x21/0x30
[  115.621174]  [<ffffffff815e7f11>] do_setlink+0x321/0x9a0
[  115.621174]  [<ffffffff810d394c>] ? __lock_acquire+0x37c/0x1a60
[  115.621174]  [<ffffffff815ea59f>] rtnl_newlink+0x51f/0x730
[  115.621174]  [<ffffffff815ea169>] ? rtnl_newlink+0xe9/0x730
[  115.621174]  [<ffffffff815e6e75>] rtnetlink_rcv_msg+0x95/0x250
[  115.621174]  [<ffffffff810d329d>] ? trace_hardirqs_on+0xd/0x10
[  115.621174]  [<ffffffff815e6dbb>] ? rtnetlink_rcv+0x1b/0x40
[  115.621174]  [<ffffffff815e6de0>] ? rtnetlink_rcv+0x40/0x40
[  115.621174]  [<ffffffff81608b19>] netlink_rcv_skb+0xa9/0xc0
[  115.621174]  [<ffffffff815e6dca>] rtnetlink_rcv+0x2a/0x40
[  115.621174]  [<ffffffff81608150>] netlink_unicast+0xf0/0x1c0
[  115.621174]  [<ffffffff8160851f>] netlink_sendmsg+0x2ff/0x740
[  115.621174]  [<ffffffff815bc9db>] sock_sendmsg+0x8b/0xc0
[  115.621174]  [<ffffffff8119d4af>] ? might_fault+0x5f/0xb0
[  115.621174]  [<ffffffff8119d4f8>] ? might_fault+0xa8/0xb0
[  115.621174]  [<ffffffff8119d4af>] ? might_fault+0x5f/0xb0
[  115.621174]  [<ffffffff815cb51e>] ? verify_iovec+0x5e/0xe0
[  115.621174]  [<ffffffff815bd4b9>] ___sys_sendmsg+0x369/0x380
[  115.621174]  [<ffffffff816faa0d>] ? __do_page_fault+0x11d/0x570
[  115.621174]  [<ffffffff810cfe9f>] ? up_read+0x1f/0x40
[  115.621174]  [<ffffffff816fab04>] ? __do_page_fault+0x214/0x570
[  115.621174]  [<ffffffff8120a10b>] ? mntput_no_expire+0x6b/0x1c0
[  115.621174]  [<ffffffff8120a0b7>] ? mntput_no_expire+0x17/0x1c0
[  115.621174]  [<ffffffff8120a284>] ? mntput+0x24/0x40
[  115.621174]  [<ffffffff815bdbb2>] __sys_sendmsg+0x42/0x80
[  115.621174]  [<ffffffff815bdc02>] SyS_sendmsg+0x12/0x20
[  115.621174]  [<ffffffff816ffd69>] system_call_fastpath+0x16/0x1b

Fix this by correctly providing macvlan lockdep class.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit dc8eaaa0.
	vlan: Fix lockdep warning when vlan dev handle notification

Instead we use the new new API to find the lock subclass of
our vlan device.  This way we can support configurations where
vlans are interspersed with other devices:
  bond -> vlan -> macvlan -> vlan
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently netif_addr_lock_nested assumes that there can be only
a single nesting level between 2 devices.  However, if we
have multiple devices of the same type stacked, this fails.
For example:
 eth0 <-- vlan0.10 <-- vlan0.10.20

A more complicated configuration may stack more then one type of
device in different order.
Ex:
  eth0 <-- vlan0.10 <-- macvlan0 <-- vlan1.10.20 <-- macvlan1

This patch adds an ndo_* function that allows each stackable
device to report its nesting level.  If the device doesn't
provide this function default subclass of 1 is used.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Multiple devices in the kernel can be stacked/nested and they
need to know their nesting level for the purposes of lockdep.
This patch provides a generic function that determines a nesting
level of a particular device by its type (ex: vlan, macvlan, etc).
We only care about nesting of the same type of devices.

For example:
  eth0 <- vlan0.10 <- macvlan0 <- vlan1.20

The nesting level of vlan1.20 would be 1, since there is another vlan
in the stack under it.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Starting from linux-3.13, GRO attempts to build full size skbs.

Problem is the commit assumed one particular field in skb->cb[]
was clean, but it is not the case on some stacked devices.

Timo reported a crash in case traffic is decrypted before
reaching a GRE device.

Fix this by initializing NAPI_GRO_CB(skb)->last at the right place,
this also removes one conditional.

Thanks a lot to Timo for providing full reports and bisecting this.

Fixes: 8a29111c ("net: gro: allow to build full sized skb")
Bisected-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

The connected check fails to check for ip_gre nbma mode tunnels
properly. ip_gre creates temporary tnl_params with daddr specified
to pass-in the actual target on per-packet basis from neighbor
layer. Detect these tunnels by inspecting the actual tunnel
configuration.

Minimal test case:
 ip route add 192.168.1.1/32 via 10.0.0.1
 ip route add 192.168.1.2/32 via 10.0.0.2
 ip tunnel add nbma0 mode gre key 1 tos c0
 ip addr add 172.17.0.0/16 dev nbma0
 ip link set nbma0 up
 ip neigh add 172.17.0.1 lladdr 192.168.1.1 dev nbma0
 ip neigh add 172.17.0.2 lladdr 192.168.1.2 dev nbma0
 ping 172.17.0.1
 ping 172.17.0.2

The second ping should be going to 192.168.1.2 and head 10.0.0.2;
but cached gre tunnel level route is used and it's actually going
to 192.168.1.1 via 10.0.0.1.

The lladdr's need to go to separate dst for the bug to trigger.
Test case uses separate route entries, but this can also happen
when the route entry is same: if there is a nexthop exception or
the GRE tunnel is IPsec'ed in which case the dst points to xfrm
bundle unique to the gre lladdr.

Fixes: 7d442fab ("ipv4: Cache dst in tunnels")
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding more than one chip on device-tree currently causes the probing
routine to always use the first chips data pointer.
Signed-off-by: Fabian Godehardt <fg@emlix.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, "ip -6 route get mark xyz" ignores the mark passed in
by userspace. Make it honour the mark, just like IPv4 does.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Include changes:
- fix NULL dereference in batadv_orig_hardif_seq_print_text()
- fix reference counting imbalance when using fragmentation
- avoid access to orig_node objects after they have been free'd
- fix local TT check for outgoing arp requests in DAT

When the NAPI budget was not all used, xenvif_poll() would call
napi_complete() /after/ enabling the interrupt.  This resulted in a
race between the napi_complete() and the napi_schedule() in the
interrupt handler.  The use of local_irq_save/restore() avoided by
race iff the handler is running on the same CPU but not if it was
running on a different CPU.

Fix this properly by calling napi_complete() before reenabling
interrupts (in the xenvif_napi_schedule_or_enable_irq() call).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
pull request: wireless 2014-05-15

Please pull this batch of fixes for the 3.15 stream...

For the mac80211 bits, Johannes says:

"One fix is to get better VHT performance and the other fixes tracing
garbage or other potential issues with the interface name tracing."

And...

"This has a fix from Emmanuel for a problem I failed to fix - when
association is in progress then it needs to be cancelled while
suspending (I had fixed the same for authentication). Also included a
fix from myself for a userspace API problem that hit the iw tool and a
fix to the remain-on-channel framework."

For the iwlwifi bits, Emmanuel says:

"Alex fixes the scan by disabling the fragmented scan. David prevents
scan offload while associated, the firmware seems not to like it. I
fix a stupid bug I made in BT Coex, and fix a bad #ifdef clause in rate
scaling.  Along with that there is a fix for a NULL pointer exception
that can happen if we load the driver and our ISR gets called because
the interrupt line is shared. The fix has been tested by the reporter."

And...

"We have here a fix from David Spinadel that makes a previous fix more
complete, and an off-by-one issue fixed by Eliad in the same area.
I fix the monitor that broke on the way."

Beyond that...

Daniel Kim's one-liner fixes a brcmfmac regression caused by a typo
in an earlier commit..

Rajkumar Manoharan fixes an ath9k oops reported by David Herrmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There may be padding on the ticket contained in the key payload, so just ensure
that the claimed token length is large enough, rather than exactly the right
size.
Signed-off-by: Nathaniel Wesley Filardo <nwf@cs.jhu.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With commit be9dad1f ("net: phy: suspend phydev when going
to HALTED"), an unused PHY device will be put in a low-power mode
using BMCR_PDOWN. Some Ethernet drivers might be calling phy_start()
and phy_stop() from ndo_open and ndo_close() respectively, while
calling phy_connect() and phy_disconnect() from probe and remove.
In such a case, the PHY will be powered down during the phy_stop()
call, but will fail to be powered up in phy_start().
This patch fixes this scenario.
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4: Fix VF MAC address change under RoCE usage

This short series provides proper handling for the case where a
VF netdevice change their MAC address under a RoCE use case. The code
it deals with was introduced in 3.15-rc1

Prior to this series the source MAC used for the VM RoCE CM
packets remains as before the MAC modification. Hence RoCE CM
packets sent by the VF will not carry the same source MAC
address as the non-CM packets.

Earlier 3.15-rc commit f24f790f "net/mlx4_core: Load the Eth driver
first" handled just one instance of the problem, but this one
provides a more generic and proper solution which covers all
cases of VF mac change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When we receive a netdev event indicating a netdev change and/or
a netdev address change, we must change the MAC index used by the
proxy QP1 (in the QP context), otherwise RoCE CM packets sent by the
VF will not carry the same source MAC address as the non-CM packets.

We use the UPDATE_QP command to perform this change.

In order to avoid modifying a QP context based on netdev event,
while the driver attempts to destroy this QP (e.g either the mlx4_ib
or ib_mad modules are unloaded), we use mutex locking in both flows.

Since the relevant mlx4 proxy GSI QP is created indirectly by the
mad module when they create their GSI QP, the mlx4 didn't need to
keep track on that QP prior to this change.

Now, when QP modifications are needed to this QP from within the
driver, we added refernece to it.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds UPDATE_QP SRIOV wrapper support.

The mechanism is a general one, but currently only source MAC
index changes are allowed for VFs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I've missed to add a NULL entry to the bond_intmax_tbl when I introduced
it with the conversion of arp_interval so add it now.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>

Fixes: 7bdb04ed ("bonding: convert arp_interval to use the new option API")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original series for reintroducing grant mapping for netback had a patch [1]
to handle receiving of packets from an another VIF. Grant copy on the receiving
side needs the grant ref of the page to set up the op.
The original patch assumed (wrongly) that the frags array haven't changed. In
the case reported by Sander, the sending guest sent a packet where the linear
buffer and the first frag were under PKT_PROT_LEN (=128) bytes.
xenvif_tx_submit() then pulled up the linear area to 128 bytes, and ditched the
first frag. The receiving side had an off-by-one problem when gathered the grant
refs.
This patch fixes that by checking whether the actual frag's page pointer is the
same as the page in the original frag list. It can handle any kind of changes on
the original frags array, like:
- removing granted frags from the array at any point
- adding local pages to the frags list anywhere
- reordering the frags
It's optimized to the most common case, when there is 1:1 relation between the
frags and the list, plus works optimal when frags are removed from the end or
the beginning.

[1]: 3e2234: xen-netback: Handle foreign mapped pages on the guest RX path
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 4861 states in 7.2.5:

	The IsRouter flag in the cache entry MUST be set based on the
         Router flag in the received advertisement.  In those cases
         where the IsRouter flag changes from TRUE to FALSE as a result
         of this update, the node MUST remove that router from the
         Default Router List and update the Destination Cache entries
         for all destinations using that neighbor as a router as
         specified in Section 7.3.3.  This is needed to detect when a
         node that is used as a router stops forwarding packets due to
         being configured as a host.

Currently, when dealing with NA Message which IsRouter flag changes from
TRUE to FALSE, the kernel only removes router from the Default Router List,
and don't update the Destination Cache entries.

Now in order to update those Destination Cache entries, i introduce
function rt6_clean_tohost().
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>