A randconfig build on powerpc failed with:

dtl.c: In function 'dtl_init':
dtl.c:238: error: implicit declaration of function 'firmware_has_feature'
dtl.c:238: error: 'FW_FEATURE_SPLPAR' undeclared (first use in this function)

- We need firmware.h for these definitions.
Signed-off-by: Sachin Sant <sachinp@in.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Richard Henderson pointed out that the powerpc __futex_atomic_op has a
bug: it will write the wrong value if the stwcx. fails and it has to
retry the lwarx/stwcx. loop, since 'oparg' will have been overwritten
by the result from the first time around the loop.  This happens
because it uses the same register for 'oparg' (an input) as it uses
for the result.

This fixes it by using separate registers for 'oparg' and 'ret'.

Cc: stable@kernel.org
Signed-off-by: Paul Mackerras <paulus@samba.org>

While adding native EEH support to Emulex and Qlogic drivers, it was
discovered that dev->error_state was set to pci_io_channel_normal too
late in the recovery process. These drivers rely on error_state to
determine if they can access the device in their slot_reset callback,
thus error_state needs to be set to pci_io_channel_normal in
eeh_report_reset(). Below is a detailed explanation (courtesy of Richard
Lary) as to why this is necessary.

Background:
PCI MMIO or DMA accesses to a frozen slot generate additional EEH
errors. If the number of additional EEH errors exceeds EEH_MAX_FAILS the
adapter will be shutdown. To avoid triggering excessive EEH errors and
an undesirable adapter shutdown, some drivers use the
pci_channel_offline(dev) wrapper function to return a Boolean value
based on the value of pci_dev->error_state to determine if PCI MMIO or
DMA accesses are safe. If the wrapper returns TRUE, drivers must not
make PCI MMIO or DMA access to their hardware.

The pci_dev structure member error_state reflects one of three values,
1) pci_channel_io_normal, 2) pci_channel_io_frozen, 3)
pci_channel_io_perm_failure.  Function pci_channel_offline(dev) returns
TRUE if error_state is pci_channel_io_frozen or pci_channel_io_perm_failure.

The EEH driver sets pci_dev->error_state to pci_channel_io_frozen at the
point where the PCI slot is frozen. Currently, the EEH driver restores
dev->error_state to pci_channel_io_normal in eeh_report_resume() before
calling the driver's resume callback. However, when the EEH driver calls
the driver's slot_reset callback() from eeh_report_reset(), it
incorrectly indicates the error state is still pci_channel_io_frozen.

Waiting until eeh_report_resume() to restore dev->error_state to
pci_channel_io_normal is too late for Emulex and QLogic FC drivers and
any other drivers which are designed to use common code paths in these
two cases: i) those called after the driver's slot_reset callback() and
ii) those called after the PCI slot is frozen but before the driver's
slot_reset callback is called. Case i) all driver paths executed to
reinitialize the hardware after a reset and case ii) all code paths
executed by driver kernel threads that run asynchronous to the main
driver thread, such as interrupt handlers and worker threads to process
driver work queues.

Emulex and QLogic FC drivers are designed with common code paths which
require that pci_channel_offline(dev) reflect the true state of the
hardware. The state transitions that the hardware takes from Normal
Operations to Slot Frozen to Reset to Normal Operations are documented
in the Power Architecture™ Platform Requirements+ (PAPR+) in Table 75.
PE State Control.

PAPR defines the following 3 states:

0 -- Not reset, Not EEH stopped, MMIO load/store allowed, DMA allowed
     (Normal Operations)
1 -- Reset, Not EEH stopped, MMIO load/store disabled, DMA disabled
2 -- Not reset, EEH stopped, MMIO load/store disabled, DMA disabled
     (Slot Frozen)

An EEH error places the slot in state 2 (Frozen) and the adapter driver
is notified that an EEH error was detected. If the adapter driver
returns PCI_ERS_RESULT_NEED_RESET, the EEH driver calls
eeh_reset_device() to place the slot into state 1 (Reset) and
eeh_reset_device completes by placing the slot into State 0 (Normal
Operations). Upon return from eeh_reset_device(), the EEH driver calls
eeh_report_reset, which then calls the adapter's slot_reset callback. At
the time the adapter's slot_reset callback is called, the true state of
the hardware is Normal Operations and should be accurately reflected by
setting dev->error_state to pci_channel_io_normal.

The current implementation of EEH driver does not do so and requires
this change to correct this deficiency.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Acked-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Now that shmem's divisions by zero and SHMEM_MAX_BYTES are fixed,
let powerpc 256kB pages coexist with CONFIG_SHMEM again.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

This patch documents the new bindings for the MPC I2C bus driver.
Furthermore, it removes obsolete FSL device related definitions
for I2C.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

arch/powerpc/mm/tlb_nohash.c: In function 'flush_tlb_mm':
arch/powerpc/mm/tlb_nohash.c:128: warning: unused variable 'cpu_mask'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Enable highmem support for the TQM8548-AG modules and NAND support for
the TQM8548-BE modules. Furthermore disable USB, Wireless and IDE support
because it's not available on the STK85xx starter kit.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

For enet2 and enet3 the wrong phy-handles have been used in DTS files
of the TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Commit 0f73a449 added I2C device nodes
for the LM75 thermal sensor on the TQM85xx modules, unfortunately with
the wrong I2C address. The LM75s are located at address 0x48.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

During the ISA 2.06 development the opcode for tlbilx changed and some
early implementations used to old opcode.  Add support for a MMU_FTR
fixup to deal with this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

The tlbilx opcode was not matching the Power ISA 2.06 arch spec.
The old opcode was an early suggested opcode that changed during the
2.06 architecture process.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

This fixes a problem reported by Sean MacLennan where loading any
module would cause an oops.  We weren't marking the pages containing
the module text as having hardware execute permission, due to a bug
introduced in commit 8d1cf34e ("powerpc/mm: Tweak PTE bit combination
definitions"), hence trying to execute the module text caused an
exception on processors that support hardware execute permission.

This adds _PAGE_HWEXEC to the definitions of PAGE_KERNEL_X and
PAGE_KERNEL_ROX to fix this problem.
Reported-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

[paulus@samba.org: changed to use syscall numbers 320 and 321 since
 perf_counters is currently using 319.]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>

'tramp' is an unsigned long, so print it with %lx.

Fixes the following build warning:
arch/powerpc/kernel/ftrace.c:291: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Commit bb725340 ("powerpc64,
ftrace: save toc only on modules for function graph"), added an
#if CONFIG_PPC64.  This changes it to #ifdef.

Fixes the following warning on 32-bit builds:
 arch/powerpc/kernel/ftrace.c:562:5: error: "CONFIG_PPC64" is not defined
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The ptrace compat wrapper mishandles access to the fpu registers.  The
PTRACE_PEEKUSR and PTRACE_POKEUSR requests miscalculate the index into
the fpr array due to the broken FPINDEX macro.  The
PPC_PTRACE_PEEKUSR_3264 request needs to use the same formula that the
native ptrace interface uses when operating on the register number (as
opposed to the 4-byte offset).  The PPC_PTRACE_POKEUSR_3264 request
didn't take TS_FPRWIDTH into account.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The irq remapping layer seems to cause some confusion when people
see a different irq number in /proc/interrupts vs the one they
request in their driver or DTS.

So have the irq remapping layer print out a message when we map an
irq. The message is only printed the first time the irq is mapped,
and it's KERN_DEBUG so most people won't see it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>

commit 28794d34 ("powerpc/kconfig: Kill
PPC_MULTIPLATFORM") broke KEXEC, by making it dependent on BOOK3S, while it
should be PPC_BOOK3S.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

When we call giveup_fpu, we need to need to turn off VSX for the
current process.  If we don't, on return to userspace it may execute a
VSX instruction before the next FP instruction, and not have its
register state refreshed correctly from the thread_struct.  Ditto for
altivec.

This caused a bug where an unaligned lfs or stfs results in
fix_alignment calling giveup_fpu so it can use the FPRs (in order to
do a single <-> double conversion), and then returning to userspace
with FP off but VSX on.  Then if a VSX instruction is executed, before
another FP instruction, it will proceed without another exception and
hence have the incorrect register state for VSX registers 0-31.

   lfs unaligned   <- alignment exception turns FP off but leaves VSX on

   VSX instruction <- no exception since VSX on, hence we get the
                      wrong VSX register values for VSX registers 0-31,
                      which overlap the FPRs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Enable relay in pseries config, ppc64_defconfig had it enabled but pseries
did not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

We specify a 64MB RMO, but the comment says 128MB.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Instead of checking for known events, pass in all 1s so we handle future
event types.  We were currently missing the IO event type.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

PHYP tells us how often a shared processor dispatch changed physical cpus.
This can highlight performance problems caused by the hypervisor.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Make all messages consistent, some have spaces before the "...", some do not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The ibm,client-architecture method will often cause a reconfiguration reboot.
When this happens the last thing we see is:

	Hypertas detected, assuming LPAR !

Which doesn't explain what just happened.  Wrap the ibm,client-architecture
so it's clear what is going on:

	Calling ibm,client-architecture... done

In order to maintain the law of conservation of screen real estate, downgrade
two other messages to debug.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Remove duplicated #include's in
  - arch/powerpc/include/asm/ps3fb.h
  - arch/powerpc/kernel/setup-common.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The (relatively) new pmac_zilog driver doesn't use the pre-munged
IRQ numbers from the macio_dev unlike other macio things, it
directly maps it off the OF device-tree.

It does that because it can be initialized much earlier than the
registration of the macio devices, in order to get a serial
console early.

Unfortunately, that means that it "misses" some fixups done
by the macio layer to work around missing interrupt descriptions
in the device-tree of the Wallstreet machines.

This patch brings the necessary workaround into the pmac_zilog
driver itself to bring it back to working condition.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The buffer passed to the ibm,get-system-parameter RTAS call must be
in the RMA.  To ensure we pass an address in the RMA use rtas_data_buf
for the actual RTAS call and then copy the result to value.  We can't
just make it static because this can be compiled in as a module.

Also add the WDRTAS_SP_SPI_LEN so we don't litter '4' throughout the
function.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Tested-by: Adrian Reber <adrian@lisas.de>
Acked-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

The driver should pass a device that specifies internal DMA ops, but
currently NULL pointers are passed, and thus following bug pops up:

  Freescale DIU driver
  ------------[ cut here ]------------
  kernel BUG at arch/powerpc/include/asm/dma-mapping.h:237!
  Oops: Exception in kernel mode, sig: 5 [#1]
  ...
  NIP [c01658b4] allocate_buf+0x0/0x8
  LR [c0306554] fsl_diu_probe+0x2b4/0x518
  Call Trace:
  [df02be10] [c030638c] fsl_diu_probe+0xec/0x518 (unreliable)
  [df02be60] [c020cdec] of_platform_device_probe+0x5c/0x84
  [df02be80] [c018f5d0] really_probe+0x78/0x1a0
  [df02bea0] [c018f7c0] __driver_attach+0xa4/0xa8
  [df02bec0] [c018ea00] bus_for_each_dev+0x60/0x9c
  [df02bef0] [c018f414] driver_attach+0x24/0x34
  [df02bf00] [c018f168] bus_add_driver+0x12c/0x1cc
  [df02bf20] [c018fbdc] driver_register+0x6c/0x110
  [df02bf30] [c020ccb4] of_register_driver+0x54/0x70
  [df02bf40] [c03d0a50] fsl_diu_init+0x70/0xa4
  ...

This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Add aliases, and correct CS0 offset to match how u-boot
programs it (this was not a problem with cuImage because
the wrapper would reprogram the localbus to match the device
tree).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Previously, if udbg was using the CPM uart, and the normal CPM uart driver
was enabled, but the console was directed elsewhere, udbg would not be
stopped prior to initialization.  This resulted in udbg hanging forever
waiting for the CPM to process a descriptor.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Previously, this caused NULL to sometimes be passed as a device
to the DMA code.  With recent DMA changes, that now causes a BUG().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

CoreInt provides a mechansim to deliver the IRQ vector directly
into the core on an interrupt (via the SPR EPR) rather than having
to go IACK on the PIC.  This is suppose to provide an improvment
in interrupt latency by reducing the time to get the IRQ vector.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

* 'audit.b62' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
  Audit: remove spaces from audit_log_d_path
  audit: audit_set_auditable defined but not used
  audit: incorrect ref counting in audit tree tag_chunk
  audit: Fix possible return value truncation in audit_get_context()
  audit: ignore terminating NUL in AUDIT_USER_TTY messages
  Audit: fix handling of 'strings' with NULL characters
  make the e->rule.xxx shorter in kernel auditfilter.c
  auditsc: fix kernel-doc notation
  audit: EXECVE record - removed bogus newline

* 'for-next' of git://git.o-hand.com/linux-mfd:
  mfd: fix da903x warning
  mfd: fix MAINTAINERS entry
  mfd: Use the value of the final spin when reading the AUXADC
  mfd: Storage class should be before const qualifier
  mfd: PASIC3: supply clock_rate to DS1WM via driver_data
  mfd: remove DS1WM clock handling
  mfd: remove unused PASIC3 bus_shift field
  pxa/magician: remove deprecated .bus_shift from PASIC3 platform_data
  mfd: convert PASIC3 to use MFD core
  mfd: convert DS1WM to use MFD core
  mfd: Support active high IRQs on WM835x
  mfd: Use bulk read to fill WM8350 register cache
  mfd: remove duplicated #include from pcf50633

* 'for-linus' of git://repo.or.cz/cris-mirror:
  CRISv32: Remove extraneous space between -I and the path.
  cris: convert obsolete hw_interrupt_type to struct irq_chip
  BUG to BUG_ON changes
  cpumask: use mm_cpumask() wrapper: cris
  cpumask: Use accessors code.: cris
  cpumask: prepare for iterators to only go to nr_cpu_ids/nr_cpumask_bits.: cris

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (140 commits)
  ACPI: processor: use .notify method instead of installing handler directly
  ACPI: button: use .notify method instead of installing handler directly
  ACPI: support acpi_device_ops .notify methods
  toshiba-acpi: remove MAINTAINERS entry
  ACPI: battery: asynchronous init
  acer-wmi: Update copyright notice & documentation
  acer-wmi: Cleanup the failure cleanup handling
  acer-wmi: Blacklist Acer Aspire One
  video: build fix
  thinkpad-acpi: rework brightness support
  thinkpad-acpi: enhanced debugging messages for the fan subdriver
  thinkpad-acpi: enhanced debugging messages for the hotkey subdriver
  thinkpad-acpi: enhanced debugging messages for rfkill subdrivers
  thinkpad-acpi: restrict access to some firmware LEDs
  thinkpad-acpi: remove HKEY disable functionality
  thinkpad-acpi: add new debug helpers and warn of deprecated atts
  thinkpad-acpi: add missing log levels
  thinkpad-acpi: cleanup debug helpers
  thinkpad-acpi: documentation cleanup
  thinkpad-acpi: drop ibm-acpi alias
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
  sh: sh7785lcr: Map whole PCI address space.
  sh: Fix up DSP context save/restore.
  sh: Fix up number of on-chip DMA channels on SH7091.
  sh: update defconfigs.
  sh: Kill off broken direct-mapped cache mode.
  sh: Wire up ARCH_HAS_DEFAULT_IDLE for cpuidle.
  sh: Add a command line option for disabling I/O trapping.
  sh: Select ARCH_HIBERNATION_POSSIBLE.
  sh: migor: Fix up CEU use flags.
  input: migor_ts: add wakeup support
  rtc: rtc-sh: use set_irq_wake()
  input: sh_keysc: use enable/disable_irq_wake()
  sh: intc: set_irq_wake() support
  sh: intc: install enable, disable and shutdown callbacks
  clocksource: sh_cmt: use remove_irq() and remove clockevent workaround
  sh: ap325 and Migo-R use new sh_mobile_ceu_info flags
  sh: Fix up -Wformat-security whining.
  sh: ap325rxa: Add ov772x support, again.
  sh: Sanitize asm/mmu.h for assembly use.
  sh: Tidy up sh7786 pinmux table.
  ...

* 'avr32-arch' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
  avr32: add hardware handshake support to atmel_serial
  avr32: add RTS/CTS/CLK pin selection for the USARTs
  Add RTC support for Merisc boards
  avr32: at32ap700x: setup DMA for AC97C in the machine code
  avr32: at32ap700x: setup DMA for ABDAC in the machine code
  Add Merisc board support
  avr32: use gpio_is_valid() to check USBA vbus_pin I/O line
  atmel-usba-udc: use gpio_is_valid() to check vbus_pin I/O line
  avr32: fix timing LCD parameters for EVKLCD10X boards
  avr32: use GPIO line PB15 on EVKLCD10x boards for backlight
  avr32: configure MCI detect and write protect pins for EVKLCD10x boards
  avr32: set pin mask to alternative 18 bpp for EVKLCD10x boards
  avr32: add pin mask for 18-bit color on the LCD controller
  avr32: fix 15-bit LCDC pin mask to use MSB lines