- 24 May, 2013 34 commits
-
-
Nishant Sarmukadam authored
The firmware hang issue is not seen very often, though it is still seen sometimes (once in 12 hours in local tests). The changes in the driver ,to interrupt the firmware, are needed when we detect that firmware is stuck and when the host queues are full and we begin to drop packets. This is to ensure that the firmware does not miss any PPA_RDY interrupts to cause the firmware restart dont miss PPA_READY interrupt for SC2 Signed-off-by:
Nishant Sarmukadam <nishants@marvell.com> Signed-off-by:
Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Wei Yongjun authored
Use kfree_skb() instead of kfree() to free sk_buff. Introduced by commit e270045b (wil6210: Sanity check for reported DMA length) Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
Stanislaw Gruszka <stf_xl@wp.pl> Acked-by:
Helmut Schaa <helmut.schaa@googlemail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Create helper function and move initialization to subroutines. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
New routine for SOC specific BBP initialization, empty for now. Signed-off-by:
-
Stanislaw Gruszka authored
Signed-off-by:
-
Stanislaw Gruszka authored
This function can not fail, we always return 0. Signed-off-by:
-
- 22 May, 2013 6 commits
-
-
Libo Chen authored
set the owner of platform_driver, to ensure that the caller of driver holds a module refernece Signed-off-by:
Libo Chen <libo.chen@huawei.com> Signed-off-by:
-
Yogesh Ashok Powar authored
Some of the key differences between SD8897 and older chipsets are as follows: a) sdio mpa_rx and mpa_tx ports have been increased from 16 to 32 b) Same is the case with read/write bitmap that one receives from mpa_reg read c) aggregation packet count doubled from 8 to 16 d) Most of key reg addresses are changed e) There is a separate command or control port f) Now command rx/tx_done have new interrupts 1. 'supports_sdio_new_mode' flag is added to handle (a) and (b). 2. (c) and (d) are taken care of by filling chip specific information in global structurei (mwifiex_sdio_sd8897). 3. For older chipsets, port 0 was cmd port and port 1->15 were data port. Therefore we had CTRL_PORT_MASK to differentiate port type. Now these changes are under 'has_control_mask' flag. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
Frank Huang <frankh@marvell.com> Signed-off-by:
-
Amitkumar Karwar authored
There are some macros defined for multiport aggregation calculations. As we may need to add some more code to accomodate new chipsets, we will change them to inline functions. Also, use dynamic allocation for Rx buffer array. Signed-off-by:
-
Amitkumar Karwar authored
They are not used in the code. Signed-off-by:
-
Amitkumar Karwar authored
As Multiple-Port Aggregation base address value is fixed, we can have a macro for it. Signed-off-by:
-
Amitkumar Karwar authored
This patch rearranges the code for better readability Signed-off-by:
-
