- 31 Aug, 2020 2 commits
-
-
Colin Ian King authored
There is a spelling mistake in an ath11k_warn warning message. Fix it. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200819074729.48591-1-colin.king@canonical.com
-
Allen Pais authored
In preparation for unconditionally passing the struct tasklet_struct pointer to all tasklet callbacks, switch to using the new tasklet_setup() and from_tasklet() to pass the tasklet pointer explicitly. Signed-off-by:
Allen Pais <allen.lkml@gmail.com> Signed-off-by:
-
- 27 Aug, 2020 17 commits
-
-
Allen Pais authored
In preparation for unconditionally passing the struct tasklet_struct pointer to all tasklet callbacks, switch to using the new tasklet_setup() and from_tasklet() to pass the tasklet pointer explicitly. Signed-off-by:
Romain Perier <romain.perier@gmail.com> Signed-off-by:
Christian Lamparter <chunkeey@gmail.com> Signed-off-by:
-
Lee Jones authored
Kerneldoc expects attributes/parameters to be in '@*.: ' format and gets confused if the variable does not follow the type/attribute definitions. Fixes the following W=1 kernel build warning(s): drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'wil' not described in 'wil6210_debugfs_init_offset' drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'dbg' not described in 'wil6210_debugfs_init_offset' drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'base' not described in 'wil6210_debugfs_init_offset' drivers/net/wireless/ath/wil6210/debugfs.c:456: warning: Function parameter or member 'tbl' not described in 'wil6210_debugfs_init_offset' Cc: Maya Erez <merez@codeaurora.org> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: wil6210@qti.qualcomm.com Cc: netdev@vger.kernel.org Signed-off-by:
Lee Jones <lee.jones@linaro.org> Reviewed-by:
Maya Erez <merez@codeaurora.org> Signed-off-by:
-
Gustavo A. R. Silva authored
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Acked-by:
-
Dan Carpenter authored
Returning PTR_ERR(NULL) means success, but we should return -ENOMEM. Fixes: 1399fb87 ("ath11k: register MHI controller device for QCA6390") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Alex Dewar authored
In ath11k_qmi_prepare_bdf_download(), ath11k_core_firmware_request() is called, but the returned pointer is not checked for errors. Rather the variable ret (which will always be zero) is checked by mistake. Fix this and replace the various gotos with simple returns for clarity. While we are at it, move the call to memset, as variable bd is not used on all code paths. Fixes: 7b57b2dd ("ath11k: create a common function to request all firmware files") Signed-off-by:
Alex Dewar <alex.dewar90@gmail.com> Signed-off-by:
-
Krzysztof Kozlowski authored
The ath9k driver hides all LEDs related code behind CONFIG_MAC80211_LEDS ifdefs so it does not really require the MAC80211_LEDS. The code builds fine. Convert the "select" into "imply" to allow disabling LED trigger when not needed. Signed-off-by:
Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by:
-
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/net/wireless/ath/ath9k/ar5008_initvals.h:627:18: warning: ‘ar5416Bank7’ defined but not used [-Wunused-const-variable=] 627 | static const u32 ar5416Bank7[][2] = { | ^~~~~~~~~~~ drivers/net/wireless/ath/ath9k/ar5008_initvals.h:548:18: warning: ‘ar5416Bank3’ defined but not used [-Wunused-const-variable=] 548 | static const u32 ar5416Bank3[][3] = { | ^~~~~~~~~~~ drivers/net/wireless/ath/ath9k/ar5008_initvals.h:542:18: warning: ‘ar5416Bank2’ defined but not used [-Wunused-const-variable=] 542 | static const u32 ar5416Bank2[][2] = { | ^~~~~~~~~~~ drivers/net/wireless/ath/ath9k/ar5008_initvals.h:536:18: warning: ‘ar5416Bank1’ defined but not used [-Wunused-const-variable=] 536 | static const u32 ar5416Bank1[][2] = { | ^~~~~~~~~~~ drivers/net/wireless/ath/ath9k/ar5008_initvals.h:462:18: warning: ‘ar5416Bank0’ defined but not used [-Wunused-const-variable=] 462 | static const u32 ar5416Bank0[][2] = { | ^~~~~~~~~~~ Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: -
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/net/wireless/ath/ath9k/ar5008_initvals.h:553:18: warning: ‘ar5416Bank6’ defined but not used [-Wunused-const-variable=] Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by:
-
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/net/wireless/ath/ath9k/ar9001_initvals.h:462:18: warning: ‘ar5416Bank6_9100’ defined but not used [-Wunused-const-variable=] Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by:
-
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/net/wireless/ath/ath9k/ar9002_initvals.h:900:18: warning: ‘ar9280PciePhy_clkreq_off_L1_9280’ defined but not used [-Wunused-const-variable=] Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com> Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by:
-
Krzysztof Kozlowski authored
The ath9k_htc driver hides all LEDs related code behind CONFIG_MAC80211_LEDS ifdefs so it does not really require the MAC80211_LEDS. The code builds and works just fine. Convert the "select" into "imply" to allow disabling LED trigger when not needed. Signed-off-by:
-
Allen Pais authored
In preparation for unconditionally passing the struct tasklet_struct pointer to all tasklet callbacks, switch to using the new tasklet_setup() and from_tasklet() to pass the tasklet pointer explicitly. Signed-off-by:
-
Lee Jones authored
Fixes the following W=1 kernel build warning(s): drivers/net/wireless/ath/ath6kl/wmi.c: In function ‘ath6kl_wmi_bitrate_reply_rx’: drivers/net/wireless/ath/ath6kl/wmi.c:1204:6: warning: variable ‘rate’ set but not used [-Wunused-but-set-variable] Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by:
-
Allen Pais authored
In preparation for unconditionally passing the struct tasklet_struct pointer to all tasklet callbacks, switch to using the new tasklet_setup() and from_tasklet() to pass the tasklet pointer explicitly. Signed-off-by:
-
Loic Poulain authored
For whatever reason, when connected to an open/no-security BSS, the wcn36xx controller in bmps mode does not forward 'wake-up' beacons despite AP sends DTIM with station AID. Meaning that AP is not able to wakeup the station and needs to wait for the station to wakeup by its own (TX data, keep alive pkt...), causing serious latency issues and unexpected deauth. When connected to AP with encryption enabled, this issue does not occur. So a simple workaround is to only enable bmps support in that case. Ideally, it should be propertly fixed to allow bmps support with open BSS, whatever the issue is at driver or firmware level. Tested on wcn3620 and wcn3680. Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Tested-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
-
Loic Poulain authored
By default, after associated to an AP, the wcn36xx bitrate adjustment algorithm starts sending data at 1Mbps, and increases the rate slowly (1Mbps, 2Mbps, 6Mbps...) over the further TX packets. Starting at 1Mbps usually causes the initial throughput to be really low and the maximum possible bitrate to be reached after about hundreed of TX packets. That can be improved by setting a different initial bitrate for data packets via the ENABLE_DYNAMIC_RA_START_RATE configuration value, this value can be a legacy or MCS rate. This patch sets the starting bitrate value to MCS-5, which seems to be a good compromise given it can be quickly adjusted low or up if necessary. (and based on what I observed in the wild with some mobile devices) Signed-off-by:
-
Loic Poulain authored
For software-driven scan, rely on mac80211 software scan instead of internal driver implementation. The internal implementation cause connection trouble since it keep the antenna busy during the entire scan duration, moreover it's only a passive scanning (no probe request). Therefore, let mac80211 manages sw scan. Note: we fallback to software scan if firmware does not report scan offload support or if we need to scan the 5Ghz band (currently not supported by the offload scan...). Signed-off-by:
-
- 26 Aug, 2020 4 commits
-
-
Tamizh Chelvam authored
Add ops for reset_tid_config to support reset TID configuration. This send default configuration to the target for the TIDs and stores default value in the host. Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021 Signed-off-by:
Tamizh Chelvam <tamizhr@codeaurora.org> Signed-off-by:
-
Tamizh Chelvam authored
This patch add ops for set_tid_config to support TID specific configuration. Station specific TID configuration will have more priority than vif specific TID configuration. WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT service flag introduced to notify host for TID config support. And RTS_CTS extended tid configuration support advertised through the service flag WMI_10_4_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT. TID specific noack configuration requires aggregation should be disabled and rate for the data TID packets should be basic rates. So, if the TID already configured with noack policy then driver will ignore the aggregation or TX rate related configuration for the same data TID. In TX rate configuration should be applied with highest preamble configuration(HT rates should not be applied for the station which supports vht rates). Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021 Signed-off-by:
-
Tamizh Chelvam authored
This patch does not have any functional changes. Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021 Signed-off-by:
-
Tamizh Chelvam authored
This patch adds WMI interface to configure station specific TID configuration . Host needs to send station's MAC address along with TID number and its configuration to target through WMI_10_4_PER_PEER_PER_TID_CONFIG_CMDID. WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT flag is added to advertise this support. Tested-on: QCA9984 hw1.0 PCI 10.4-3.9.0.2-00021 Signed-off-by:
-
- 19 Aug, 2020 2 commits
-
-
Wen Gong authored
When firmware crashes it's possible to create a coredump for later analysis, add support to collect the register and memory info from SDIO devices. The coredump configuration is different between QCA6174 PCI and QCA6174 SDIO, so add specific registers and memory regions for the latter. QCA6174 SDIO has two methods to dump the firmware: fastdump and slowdump. Fastdump is not supported in olded versions of firmware, and for these ath10k will automatically select slowdump. If firmware supports fastdump, ath10k will automatically select it. QCA6174 SDIO firmware version WLAN.RMH.4.4.1-00017-QCARMSWPZ-2 is the first version supporting fastdump. For slowdump, ath10k_sdio_hif_diag_read() can not be used as the diag window has a limit value, it is 4 bytes and the dump's buffer length is larger than it, it will trigger error. So this patch adds ath10k_sdio_read_mem() to read 4 bytes for each time. Example output of a firmware crash: ath10k_sdio mmc1:0001:1: simulating soft firmware crash ath10k_sdio mmc1:0001:1: firmware crashed! (guid 413d98b1-84c0-4298-b605-2b10ec0c54a5) ath10k_sdio mmc1:0001:1: qca6174 hw3.2 sdio target 0x05030000 chip_id 0x00000000 sub 0000:0000 ath10k_sdio mmc1:0001:1: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 1 ath10k_sdio mmc1:0001:1: firmware ver WLAN.RMH4.4.1-00126-QCARMSWP-1 api 6 features wowlan,ignore-otp,raw-mode crc32 b84317cf ath10k_sdio mmc1:0001:1: board_file api 2 bmi_id 0:4 crc32 6364cfcc ath10k_sdio mmc1:0001:1: htt-ver 3.69 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1 ath10k_sdio mmc1:0001:1: firmware register dump: ath10k_sdio mmc1:0001:1: [00]: 0x05030000 0x000015B3 0x0099908D 0x00955B31 ath10k_sdio mmc1:0001:1: [04]: 0x0099908D 0x00060730 0x00000018 0x004641A0 ath10k_sdio mmc1:0001:1: [08]: 0x0041FAA4 0x0041FA9C 0x00999070 0x00404490 ath10k_sdio mmc1:0001:1: [12]: 0x00000009 0xFFFFFFFF 0x00952CD0 0x00952CE6 ath10k_sdio mmc1:0001:1: [16]: 0x00952CC4 0x00910712 0x00000000 0x00000000 ath10k_sdio mmc1:0001:1: [20]: 0x4099908D 0x0040E9E8 0x00000001 0x00423AC0 ath10k_sdio mmc1:0001:1: [24]: 0x809F3189 0x0040EA48 0x00426240 0xC099908D ath10k_sdio mmc1:0001:1: [28]: 0x809143A7 0x0040EA68 0x0041FAA4 0x00423A80 ath10k_sdio mmc1:0001:1: [32]: 0x809F1193 0x0040EA88 0x00411770 0x004117E0 ath10k_sdio mmc1:0001:1: [36]: 0x809F0EEE 0x0040EAA8 0x00000000 0x00000000 ath10k_sdio mmc1:0001:1: [40]: 0x80911210 0x0040EAC8 0x00000008 0x00404130 ath10k_sdio mmc1:0001:1: [44]: 0x80911154 0x0040EB28 0x00400000 0x00000000 ath10k_sdio mmc1:0001:1: [48]: 0x8091122D 0x0040EB48 0x00000000 0x00400600 ath10k_sdio mmc1:0001:1: [52]: 0x40910024 0x0040EB78 0x0040AB98 0x0040AB98 ath10k_sdio mmc1:0001:1: [56]: 0x00000000 0x0040EB98 0x009BB001 0x00040020 Tested-on: QCA6174 SDIO WLAN.RMH.4.4.1-00018-QCARMSWP-1 Signed-off-by:
Wen Gong <wgong@codeaurora.org> Signed-off-by:
-
Wen Gong authored
For some hw version, it has more than one bus type, it need to add bus type to distinguish different chip. Tested-on: QCA6174 SDIO WLAN.RMH.4.4.1-00018-QCARMSWP-1 Signed-off-by:
-
- 18 Aug, 2020 15 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.10. Major changes: ath11k * add support for QCA6390 PCI devices wcn36xx * add support for TX ack ath9k * add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0 rekeying
-
Tom Rix authored
clang static analysis reports this problem rndis_wlan.c:3147:25: warning: Assigned value is garbage or undefined wiphy->max_num_pmkids = le32_to_cpu(caps.num_pmkids); ^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The setting of caps happens here, with a call to rndis_query_oid() retval = rndis_query_oid(usbdev, if (retval >= 0) { Reviewing rndis_query_oid() shows that on success 0 is returned, failure is otherwise. So the retval check is not tight enough. So tighten the retval check. Similar problem in rndis_wlan_get_caps(). Signed-off-by:Tom Rix <trix@redhat.com> Signed-off-by:
-
Christophe JAILLET authored
A possible call chain is as follow: mwifiex_sdio_interrupt (sdio.c) --> mwifiex_main_process (main.c) --> mwifiex_process_cmdresp (cmdevt.c) --> mwifiex_process_sta_cmdresp (sta_cmdresp.c) --> mwifiex_ret_802_11_scan (scan.c) --> mwifiex_parse_single_response_buf (scan.c) 'mwifiex_sdio_interrupt()' is an interrupt function. Also note that 'mwifiex_ret_802_11_scan()' already uses GFP_ATOMIC. So use GFP_ATOMIC instead of GFP_KERNEL when memory is allocated in 'mwifiex_parse_single_response_buf()'. Fixes: 7c6fa2a8 ("mwifiex: use cfg80211 dynamic scan table and cfg80211_get_bss API") or Fixes: 601216e1 ("mwifiex: process RX packets in SDIO IRQ thread directly") Signed-off-by:Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Christophe JAILLET authored
The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'adm8211_alloc_rings()', GFP_KERNEL can be used because it is called only from the probe function and no lock is acquired. Moreover, GFP_KERNEL is already used just a few lines above in a kmalloc. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by:
-
Colin Ian King authored
There are some spelling mistakes in rtw_info messages. Fix these. Signed-off-by:
-
Colin Ian King authored
There are spelling mistakes in warning messages. Fix these. Signed-off-by:
-
Tom Rix authored
Clang static analysis reports this error brcmfmac/core.c:490:4: warning: Dereference of null pointer (*ifp)->ndev->stats.rx_errors++; ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ In this block of code if (ret || !(*ifp) || !(*ifp)->ndev) { if (ret != -ENODATA && *ifp) (*ifp)->ndev->stats.rx_errors++; brcmu_pkt_buf_free_skb(skb); return -ENODATA; } (*ifp)->ndev being NULL is caught as an error But then it is used to report the error. So add a check before using it. Fixes: 91b63280 ("brcmfmac: Use net_device_stats from struct net_device") Signed-off-by: -
Andy Shevchenko authored
Use %*ph format to print small buffer as hex string. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Wang Yufen authored
When brcmf_proto_msgbuf_attach fail and msgbuf->txflow_wq != NULL, we should destroy the workqueue. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Wang Yufen <wangyufen@huawei.com> Signed-off-by:
-
Gustavo A. R. Silva authored
Replace the existing /* fall through */ comments and its variants with the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary fall-through markings when it is the case. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by:
-
Wang Yufen authored
When qmi_add_lookup fail, we should destroy the workqueue Fixes: d5c65159 ("ath11k: driver for Qualcomm IEEE 802.11ax devices") Reported-by:
-
Sathishkumar Muruganandam authored
When STBC is enabled, NSTS_SU value need to be accounted for VHT NSS calculation for SU case. Without this fix, 1SS + STBC enabled case was reported wrongly as 2SS in radiotap header on monitor mode capture. Tested-on: QCA9984 10.4-3.10-00047 Signed-off-by:
Sathishkumar Muruganandam <murugana@codeaurora.org> Signed-off-by:
-
Rakesh Pillai authored
As a part of device shutdown the smmu driver will be stopped and henceforth any IOVA address translation will not be done. The wlan driver, being one of the smmu driver consumer, should stop all the dma related activity as a part of shutdown, and thereby ensuring that no dma activity is done once the smmu driver shuts down. During the device shutdown, the smmu calls shutdown for all its consumers in order to indicate them to stop all their dma activities. Register the shutdown handler to stop the wlan driver and avoid any dma operations. Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1 Signed-off-by:
Rakesh Pillai <pillair@codeaurora.org> Signed-off-by:
-
Carl Huang authored
For QCA6390, normal power up and power down can't bring MHI to a workable state. This happens especially in warm reboot and rmmod and insmod. Host needs to write a few registers to bring MHI to normal state. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 Signed-off-by:
Carl Huang <cjhuang@codeauroro.org> Signed-off-by:
-
Carl Huang authored
For QCA6390, wbm2sw1 is used for other purpose rather than tx completion ring. So use TCL_DATA_RING 0 only for QCA6390. Add MISC_CAPS_TCL_0_ONLY to control it. Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1 Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2 Signed-off-by:
Carl Huang <cjhuang@codeaurora.org> Signed-off-by:
-
