This does the same as the previous commit, but for the S bit, which also
needs to match the initial value which the assembly code used for the
same reasons.  Again, we add a check for SMP to ensure that the page
tables are correctly setup for SMP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Fix a long standing bug where, for ARMv6+, we don't fully ensure that
the C code sets the same cache policy as the assembly code.  This was
introduced partially by commit 11179d8c ([ARM] 4497/1: Only allow
safe cache configurations on ARMv6 and later) and also by adding SMP
support.

This patch sets the default cache policy based on the flags used by the
assembly code, and then ensures that when a cache policy command line
argument is used, we verify that on ARMv6, it matches the initial setup.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We can use the alignment_trap assembly macro here too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

cr_no_alignment is really only used by the alignment code.  Since we no
longer change the setting of cr_alignment after boot, we can localise
this to alignment.c
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

alignment.c will not be built unless CPU_CP15 is set:

config CPU_CP15
        bool

config CPU_CP15_MMU
        bool
        select CPU_CP15

config ALIGNMENT_TRAP
        bool
        depends on CPU_CP15_MMU

So there's no point having conditionals on CPU_CP15 within this code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

adjust_cr() is not used anymore, so let's get rid of it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Keep all bits of alignment handling together.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Several places open-code this manipulation, let's consolidate this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

memblock is now fully integrated into the kernel and is the prefered
method for tracking memory. Rather than reinvent the wheel with
meminfo, migrate to using memblock directly instead of meminfo as
an intermediate.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Due to a design incompatibility between the PCIe Marvell controller
and the Cortex-A9, stressing PCIe devices with a lot of traffic
quickly causes a deadlock.

One part of the workaround for this is to have all PCIe regions mapped
as strongly-ordered (MT_UNCACHED) instead of the default
MT_DEVICE. While the arch_ioremap_caller() mechanism allows
sub-architecture code to override ioremap(), used to map PCIe memory
regions, there isn't such a mechanism to override the behavior of
pci_ioremap_io().

This commit adds the arch_pci_ioremap_mem_type variable, initialized
to MT_DEVICE by default, and that sub-architecture code can
override. We have chosen to expose a single variable rather than
offering the possibility of overriding the entire pci_ioremap_io(),
because implementing pci_ioremap_io() requires calling functions
(get_mem_type()) that are private to the arch/arm/mm/ code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

A small mistake slipped through in memory.txt.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When configure kprobe events of ftrace with "stacktrace" option enabled
in arm, there is no stacktrace was recorded after the kprobe event was
triggered. The root cause is no save_stack_trace_regs() function implemented.

Implement the save_stack_trace_regs() function in arm, then ftrace will
call this architecture-related function to record the stacktrace into
ring buffer.

After this fix, stacktrace can be recorded, for example:

 # mount -t debugfs nodev /sys/kernel/debug
 # echo "p:netrx net_rx_action" >> /sys/kernel/debug/tracing/kprobe_events
 # echo 1 > /sys/kernel/debug/tracing/events/kprobes/netrx/enable
 # echo 1 > /sys/kernel/debug/tracing/options/stacktrace
 # echo 1 > /sys/kernel/debug/tracing/tracing_on
 # ping 127.0.0.1 -c 1
 # echo 0 > /sys/kernel/debug/tracing/tracing_on

 # cat /sys/kernel/debug/tracing/trace
 # tracer: nop
 #
 # entries-in-buffer/entries-written: 12/12   #P:1
 #
 #                              _-----=> irqs-off
 #                             / _----=> need-resched
 #                            | / _---=> hardirq/softirq
 #                            || / _--=> preempt-depth
 #                            ||| /     delay
 #           TASK-PID   CPU#  ||||    TIMESTAMP  FUNCTION
 #              | |       |   ||||       |         |
             <------ missing some entries ---------------->
             ping-1200  [000] dNs1   667.603250: netrx: (net_rx_action+0x0/0x1f8)
             ping-1200  [000] dNs1   667.604738: <stack trace>
  => net_rx_action
  => do_softirq
  => local_bh_enable
  => ip_finish_output
  => ip_output
  => ip_local_out
  => ip_send_skb
  => ip_push_pending_frames
  => raw_sendmsg
  => inet_sendmsg
  => sock_sendmsg
  => SyS_sendto
  => ret_fast_syscall
Signed-off-by: Lin Yongting <linyongting@gmail.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Support for ARM710 CPUs was removed in v3.5. Now remove the last code
depending on its Kconfig macro.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We will reach fixup handler when one thread(say cpu0) caused an undefined exception, while another thread(say cpu1) is unmmaping the page.

Fixup handler returns to the next userspace instruction which has caused the undef execption, rather than going to the same instruction.

ARM ARM says that after undefined exception, the PC will be pointing
to the next instruction. ie +4 offset in case of ARM and +2 in case of Thumb

And there is no correction offset passed to vector_stub in case of
undef exception.

File: arch/arm/kernel/entry-armv.S +1085
vector_stub     und, UND_MODE

During an undefined exception, in normal scenario(ie when ldrt
instruction does not cause an abort) after resorting the context in
VFP hardware, the PC is modified as show below before jumping to
ret_from_exception which is in r9.

File: arch/arm/vfp/vfphw.S +169
@ The context stored in the VFP hardware is up to date with this thread
vfp_hw_state_valid:
   tst     r1, #FPEXC_EX
   bne     process_exception     @ might as well handle the pending
                                 @ exception before retrying branch
                                 @ out before setting an FPEXC that
                                 @ stops us reading stuff
        VFPFMXR FPEXC, r1        @ Restore FPEXC last
        sub     r2, r2, #4       @ Retry current instruction - if Thumb
        str     r2, [sp, #S_PC]  @ mode it's two 16-bit instructions,
                                 @ else it's one 32-bit instruction, so
                                 @ always subtract 4 from the following
                                 @ instruction address.

But if ldrt results in an abort, we reach the fixup handler and return
to ret_from_execption without correcting the pc.

This patch modifes the fixup handler to re-execute the same instruction which caused undefined execption.
Signed-off-by: Vinayak Menon <vinayakm.list@gmail.com>
Signed-off-by: Arun KS <getarunks@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

asm-generic offers an atomic-add based rwsem implementation, which
can avoid the need for heavier, spinlock-based synchronisation on the
fast path.

This patch makes use of the optimised implementation for ARM CPUs.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

As we have now removed all instances of the L2C-310 having its cache
size "modified" via platform/SoC code, discourage new cases showing
up by printing a warning.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

We no longer need or require the .set_debug method; we handle everything
it used to do via the .write_sec method instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

L2X0_AUX_CTRL_MASK is not useful for PL310s.  It would be better if
people thought about their value for this rather than cargo-cult
programming.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove the explicit call to l2x0_of_init(), converting to the generic
infrastructure instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The cache size should already be present in the L2 cache auxiliary
control register: it is part of the integration process to configure
the hardware IP.  Most platforms get this right, yet still many
cargo-cult program, and assume that they always need specifying to
the L2 cache code.  Remove them so we can find out which really need
this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove the explicit call to l2x0_of_init(), converting to the generic
infrastructure instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

It is beneficial to have the L2 cache up and running earlier in the
system boot.  Not only will this allow for simpler code when we come to
enable some features, but it also means that we get a more accurate
bogomips value for the udelay() loop.  Calibrating the loop with the
L2 cache off, and then running with the L2 cache on is not the best
idea.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

ux500 can't change the auxiliary control register, so there's no point
passing values to try and modify it to the l2x0 init functions.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The cache size should already be present in the L2 cache auxiliary
control register: it is part of the integration process to configure
the hardware IP.  Most platforms get this right, yet still many
cargo-cult program, and assume that they always need specifying to
the L2 cache code.  Remove them so we can find out which really need
this.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

ux500 can't write to any of the secure registers on the L2C controllers,
so provide a dummy handler which ignores all writes.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove the explicit call to l2x0_of_init(), converting to the generic
infrastructure instead.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The cache size should already be present in the L2 cache auxiliary
control register: it is part of the integration process to configure
the hardware IP.  Most platforms get this right, yet still many
cargo-cult program, and assume that they always need specifying to
the L2 cache code.  Remove them so we can find out which really need
this.
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove the explicit call to l2x0_of_init(), converting to the generic
infrastructure instead.  We can remove the .init_machine as it becomes
the same as the generic version.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The cache size should already be present in the L2 cache auxiliary
control register: it is part of the integration process to configure
the hardware IP.  Most platforms get this right, yet still many
cargo-cult program, and assume that they always need specifying to
the L2 cache code.  Remove them so we can find out which really need
this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove the explicit call to l2x0_of_init(), converting to the generic
infrastructure instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The cache size should already be present in the L2 cache auxiliary
control register: it is part of the integration process to configure
the hardware IP.  Most platforms get this right, yet still many
cargo-cult program, and assume that they always need specifying to
the L2 cache code.  Remove them so we can find out which really need
this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove the explicit call to l2x0_of_init(), converting to the generic
infrastructure instead.  This also allows us to eliminate the
.init_machine function as this becomes the same as the generic version.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add better commentry about the L2 cache requirements on these platforms.
Unfortunately, the auxiliary control register is not pre-set to indicate
the correct cache parameters, so we have to manually program these.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Remove the explicit call to l2x0_of_init(), converting to the generic
infrastructure instead.  Along with this change, we can delete l2x0.c
from prima2.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The cache size should already be present in the L2 cache auxiliary
control register: it is part of the integration process to configure
the hardware IP.  Most platforms get this right, yet still many
cargo-cult program, and assume that they always need specifying to
the L2 cache code.  Remove them so we can find out which really need
this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>