- 14 Aug, 2009 8 commits
-
-
Gábor Stefanik authored
Update a comment that still says IEEE80211_IF_TYPE instead of NL80211_IFTYPE. Signed-off-by:
Gábor Stefanik <netrolller.3d@gmail.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
gregor kowski authored
The tkip hw support uncovered a bug in b43_write_probe_resp_template : it is writing at the wrong shm offset, it is in the B43_SHM_SH_TKIPTSCTTAK zone. Remove b43_write_probe_resp_template, b43_write_probe_resp_plcp and b43_write_probe_resp_plcp because the probe response offload is currently not supported by mac80211. Signed-off-by:
Gregor Kowski <gregor.kowski@gmail.com> Signed-off-by:
-
Gábor Stefanik authored
Make use of HostFlags defines in the LP-PHY code. Fix fallout from the IEEE80211_IF_TYPE to NL80211_IFTYPE change. Signed-off-by:
-
Luis R. Rodriguez authored
Mesh is currently disabled on mac80211, its marked as broken. This patch gets it to compile though, to account for the mac80211 workqueue changes. There was a simple typo in the patches for mesh for the workqueue migration, but we never compile tested it as we couldn't even select mesh as its broken. Lets at least let it compile for those interested in getting it fixed. Reported-by:
Pat Erley <pat-lkml@erley.org> Signed-off-by:
Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by:
-
Gábor Stefanik authored
Add B2063 radio init code and tables for LP-PHY. Rename structures common between B2062 and B2063 to B206X. Signed-off-by:
-
Luis R. Rodriguez authored
zd1211rw uses its own LED stuff so let rename its LED stuff as such. Signed-off-by:
-
Luis R. Rodriguez authored
We used to set pspoll filter on ath9k on AP mode but we no longer need this mode specific check as mac80211 now does the check for us and informs us when we should enable pspoll through FIF_PSPOLL. Cc: Igor Perminov <igor.perminov@inbox.ru> Cc: Jouni Malinen <jouni.malinen@atheros.com> Signed-off-by:
-
Joerg Albert authored
Let ath5k_chan_set() always call ath5k_reset(). This fixes the bug that we don't get any packets in monitor mode after: ifconfig wlan0 down iwconfig wlan0 mode monitor channel 1 ifconfig wlan0 up but they arrive after iwconfig wlan0 channel 2 Signed-off-by:
Joerg Albert <jal2@gmx.de> Signed-off-by:
-
- 13 Aug, 2009 32 commits
-
-
Eilon Greenstein authored
Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
Yitchak Gertner <gertner@broadcom.com> Signed-off-by:
-
Eilon Greenstein authored
Moving the code to a more logical place and beautifying it. No real change in behavior. Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Change ieee_fc to u16 instead of u32 and re-arrange the link parameters structures Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
Yaniv Rosner <yanivr@broadcom.com> Signed-off-by:
-
Eilon Greenstein authored
Disable bmac access while working with emac and keep the single lane SerDes in reset while working with 4 lanes XGXS Signed-off-by:
-
Eilon Greenstein authored
Without this check, when running out of memory, we will see PSOD's in bnx2x_init_fill() when doing a memset(). This is because at that time, bp->gunzip_buf is not pointing to a valid allocated space. Signed-off-by:
Benjamin Li <benli@broadcom.com> Signed-off-by:
-
Eilon Greenstein authored
Moved the dmae_command from the heap to the stack. This will save 56 bytes per bnx2x structure. As a side benefit, we can also reduce the time the dmae_mutex is held. This is because do we not need to hold this mutex when setting up the dmae command. The memory where is dmae command is stored is not a shared resource and doesn not need to be protected. Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Move printing of version from probe to the init function Rather then checking if this is the first module probe call to print the version of the driver only once, the statement is moved to the init function of the module where init is only called once Signed-off-by:
-
Eilon Greenstein authored
The functions bnx2x_get_pcie_width() and bnx2x_get_pcie_speed() were combined into bnx2x_get_pcie_width_speed() so that there is only 1 PCI read to PCICFG_OFFSET + PCICFG_LINK_CONTROL rather then 2 reads. Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
In case of error, bnx2x_init_dev calls pci_set_drvdata(pdev, NULL) Signed-off-by:
-
Eilon Greenstein authored
When a given ring is running out of space, the FW can send pause towards the network. When working with multi-queues, when one queue is getting out of space it can block all other queues. The preferred scheme is to send pause frames only when running out of the shared internal chip buffers and if a given queue cannot place a packet on the host, it will drop it. Since some users might want to work in drop-less mode, allowing changing the behavior as a module parameter. Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
This is required for NCSI statistics Signed-off-by:
-
Eilon Greenstein authored
This code should not have resided in the driver. Now that we have a new interface, this logic can reside in the application that whishes to upgrade the PHY FW Signed-off-by:
-
Eilon Greenstein authored
There are 3 operations that the driver needs to support to allow applications to access the PHY FW (on top of the MDC/MDIO access). Since those are essentially nvram access commands, adding them to the ethtool -E interface. Signed-off-by:
-
Eilon Greenstein authored
As suggested by Ben Hutchings <bhutchings@solarflare.com>, using the MDC/MDIO IOCTL Signed-off-by:
-
Eilon Greenstein authored
Adding CL73 support to the built in PHY in the 5771x device. Also supporting fallbacks to CL73 if the link partner does not respond. Signed-off-by:
-
Eilon Greenstein authored
The BCM8727 is a dual port PHY. The FW must be loaded in a given order on all designs - including those which swapped the ports (calling port number zero the second port) Signed-off-by:
-
Eilon Greenstein authored
To avoid confusion, if the PHY does not have a FW (and so, no FW version) make sure that the string is NULL. Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
Eilon Greenstein authored
The BCM8481 does not generate LASI interrupt for 10M, 100M and 1G link, so we are using LED4 output as the interrupt input to the 57711. This requires some adaptation in the link interrupt routines Signed-off-by:
-
Eilon Greenstein authored
Signed-off-by:
-
