For certain sounding frames, it may be useful to report them
to userspace even though they don't have a PSDU in order to
determine the PHY parameters (e.g. VHT rate/stream config.)
Add support for this to mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Rekeying PTK keys without "Extended Key ID for Individually Addressed
Frames" did use a procedure not suitable to replace in-use keys and
could caused the following issues:

 1) Freeze caused by incoming frames:
    If the local STA installed the key prior to the remote STA we still
    had the old key active in the hardware when mac80211 switched over
    to the new key.
    Therefore there was a window where the card could hand over frames
    decoded with the old key to mac80211 and bump the new PN (IV) value
    to an incorrect high number. When it happened the local replay
    detection silently started to drop all frames sent with the new key.

 2) Freeze caused by outgoing frames:
    If mac80211 was providing the PN (IV) and handed over a clear text
    frame for encryption to the hardware prior to a key change the
    driver/card could have processed the queued frame after switching
    to the new key. This bumped the PN value on the remote STA to an
    incorrect high number, tricking the remote STA to discard all frames
    we sent later.

 3) Freeze caused by RX aggregation reorder buffer:
    An aggregation session started with the old key and ending after the
    switch to the new key also bumped the PN to an incorrect high number,
    freezing the connection quite similar to 1).

 4) Freeze caused by repeating lost frames in an aggregation session:
    A driver could repeat a lost frame and encrypt it with the new key
    while in a TX aggregation session without updating the PN for the
    new key. This also could freeze connections similar to 2).

 5) Clear text leak:
    Removing encryption offload from the card cleared the encryption
    offload flag only after the card had deleted the key and we did not
    stop TX during the rekey. The driver/card could therefore get
    unencrypted frames from mac80211 while no longer be instructed to
    encrypt them.

To prevent those issues the key install logic has been changed:
 - Mac80211 divers known to be able to rekey PTK0 keys have to set
   @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0,
 - mac80211 stops queuing frames depending on the key during the replace
 - the key is first replaced in the hardware and after that in mac80211
 - and mac80211 stops/blocks new aggregation sessions during the rekey.

For drivers not setting
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 the user space must avoid PTK
rekeys if "Extended Key ID for Individually Addressed Frames" is not
being used. Rekeys for mac80211 drivers without this flag will generate a
warning and use an extra call to ieee80211_flush_queues() to both
highlight and try to prevent the issues with not updated drivers.

The core of the fix changes the key install procedure from:
 - atomic switch over to the new key in mac80211
 - remove the old key in the hardware (stops encryption offloading, fall
   back to software encryption with a potential clear text packet leak
   in between)
 - delete the inactive old key in mac80211
 - enable hardware encryption offloading for the new key
to:
 - if it's a PTK mark the old key as tainted to drop TX frames with the
   outgoing key
 - replace the key in hardware with the new one
 - atomic switch over to the new (not marked as tainted) key in
   mac80211 (which also resumes TX)
 - delete the inactive old key in mac80211

With the new sequence the hardware will be unable to decrypt frames
encrypted with the old key prior to switching to the new key in mac80211
and thus prevent PNs from packets decrypted with the old key to be
accounted against the new key.

For that to work the drivers have to provide a clear boundary.
Mac80211 drivers setting @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 confirm
to provide it and mac80211 will then be able to correctly rekey in-use
PTK keys with those drivers.

The mac80211 requirements for drivers to set the flag have been added to
the "Hardware crypto acceleration" documentation section. It drills down
to:
The drivers must not hand over frames decrypted with the old key to
mac80211 once the call to set_key() with %DISABLE_KEY has been
completed. It's allowed to either drop or continue to use the old key
for any outgoing frames which are already in the queues, but it must not
send out any of them unencrypted or encrypted with the new key.

Even with the new boundary in place aggregation sessions with the
reorder buffer are problematic:
RX aggregation session started prior and completed after the rekey could
still dump frames received with the old key at mac80211 after it
switched over to the new key. This is side stepped by stopping all (RX
and TX) aggregation sessions when replacing a PTK key and hardware key
offloading.
Stopping TX aggregation sessions avoids the need to get
the PNs (IVs) updated in frames prepared for the old key and
(re)transmitted after the switch to the new key. As a bonus it improves
the compatibility when the remote STA is not handling rekeys as it
should.

When using software crypto aggregation sessions are not stopped.
Mac80211 won't be able to decode the dangerous frames and discard them
without special handling.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[trim overly long rekey warning]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Drivers able to correctly replace a in-use key should set
@NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to allow the user space (e.g.
hostapd or wpa_supplicant) to rekey PTK keys.

The user space must detect a PTK rekey attempt and only go ahead with it
when the driver has set this flag. If the driver is not supporting the
feature the user space either must not replace the PTK key or perform a
full re-association instead.

Ignoring this flag and continuing to rekey the connection can still work
but has to be considered insecure and broken. Depending on the driver it
can leak clear text packets or freeze the connection and is only
supported to allow the user space to be updated.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Reviewed-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

As before with HE, the data needs to be provided by the
driver in the skb head, since there's not enough space
in the skb CB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Make it possibly for drivers to adjust the default skb_pacing_shift
by storing it in the hardware struct.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[adjust commit log, move & adjust comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When taking VHT capabilities for a station, copy the new
fields if we support them as a transmitter. Also adjust
the maximum bandwidth the station supports appropriately.

Also, since it was missing, copy tx_highest and rx_highest.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

With newer VHT implementations, it's necessary to look at the
HT operation's CCFS2 field to identify the actual bandwidth
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Depending on whether or not rate control supports selecting
rates depending on the bandwidth, we can use VHT extended
NSS support. In essence, this is dot11VHTExtendedNSSBWCapable
from the spec, since depending on that we'll need to parse
the bandwidth.

If needed, also set/clear the VHT Capability Element bit for
this capability so that we don't advertise it erroneously or
don't advertise it when we actually use it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

IEEE 802.11-2016 extended the VHT capability fields to allow
indicating the number of spatial streams depending on the
actually used bandwidth, add support for decoding this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In AP mode, If AP advertises HE capabilities, set to true
bss_conf::he_supported so that the Driver knows about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Same as for HT and VHT.
This helps the lower level to know whether the AP supports HE.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The defines of IEEE80211_HE_OPERATION_VHT_OPER_INFO and
IEEE80211_HE_OPERATION_MULTI_BSSID_AP have leading zeroes
that makes the number look like it is bigger than 32 bit.
This is misleading, remove it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some drivers may want to also use the TXQ abstraction with
non-data packets that need powersave buffering, so add a
hardware flag to allow this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of open-coding the equivalent of le16_encode_bits(),
just use that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

These checks aren't necessary, cfg80211 never passes NULL.
Some static checkers complain about the missing checks on
the next line, but really the NULL checks are unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Export HE capabilities information via debugfs, similar to HT & VHT.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pull networking fixes from David Miller:

 1) Must perform TXQ teardown before unregistering interfaces in
    mac80211, from Toke Høiland-Jørgensen.

 2) Don't allow creating mac80211_hwsim with less than one channel, from
    Johannes Berg.

 3) Division by zero in cfg80211, fix from Johannes Berg.

 4) Fix endian issue in tipc, from Haiqing Bai.

 5) BPF sockmap use-after-free fixes from Daniel Borkmann.

 6) Spectre-v1 in mac80211_hwsim, from Jinbum Park.

 7) Missing rhashtable_walk_exit() in tipc, from Cong Wang.

 8) Revert kvzalloc() conversion of AF_PACKET, it breaks mmap() when
    kvzalloc() tries to use kmalloc() pages. From Eric Dumazet.

 9) Fix deadlock in hv_netvsc, from Dexuan Cui.

10) Do not restart timewait timer on RST, from Florian Westphal.

11) Fix double lwstate refcount grab in ipv6, from Alexey Kodanev.

12) Unsolicit report count handling is off-by-one, fix from Hangbin Liu.

13) Sleep-in-atomic in cadence driver, from Jia-Ju Bai.

14) Respect ttl-inherit in ip6 tunnel driver, from Hangbin Liu.

15) Use-after-free in act_ife, fix from Cong Wang.

16) Missing hold to meta module in act_ife, from Vlad Buslov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
  net: phy: sfp: Handle unimplemented hwmon limits and alarms
  net: sched: action_ife: take reference to meta module
  act_ife: fix a potential use-after-free
  net/mlx5: Fix SQ offset in QPs with small RQ
  tipc: correct spelling errors for tipc_topsrv_queue_evt() comments
  tipc: correct spelling errors for struct tipc_bc_base's comment
  bnxt_en: Do not adjust max_cp_rings by the ones used by RDMA.
  bnxt_en: Clean up unused functions.
  bnxt_en: Fix firmware signaled resource change logic in open.
  sctp: not traverse asoc trans list if non-ipv6 trans exists for ipv6_flowlabel
  sctp: fix invalid reference to the index variable of the iterator
  net/ibm/emac: wrong emac_calc_base call was used by typo
  net: sched: null actions array pointer before releasing action
  vhost: fix VHOST_GET_BACKEND_FEATURES ioctl request definition
  r8169: add support for NCube 8168 network card
  ip6_tunnel: respect ttl inherit for ip6tnl
  mac80211: shorten the IBSS debug messages
  mac80211: don't Tx a deauth frame if the AP forbade Tx
  mac80211: Fix station bandwidth setting after channel switch
  mac80211: fix a race between restart and CSA flows
  ...

Not all SFPs implement the registers containing sensor limits and
alarms. Luckily, there is a bit indicating if they are implemented or
not. Add checking for this bit, when deciding if the hwmon attributes
should be visible.

Fixes: 1323061a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recent refactoring of add_metainfo() caused use_all_metadata() to add
metainfo to ife action metalist without taking reference to module. This
causes warning in module_put called from ife action cleanup function.

Implement add_metainfo_and_get_ops() function that returns with reference
to module taken if metainfo was added successfully, and call it from
use_all_metadata(), instead of calling __add_metainfo() directly.

Example warning:

[  646.344393] WARNING: CPU: 1 PID: 2278 at kernel/module.c:1139 module_put+0x1cb/0x230
[  646.352437] Modules linked in: act_meta_skbtcindex act_meta_mark act_meta_skbprio act_ife ife veth nfsv3 nfs fscache xt_CHECKSUM iptable_mangle ipt_MASQUERADE iptable_nat nf_nat_ipv4 nf_nat xt_conntrack nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c tun ebtable_filter ebtables ip6table_filter ip6_tables bridge stp llc mlx5_ib ib_uverbs ib_core intel_rapl sb_edac x86_pkg_temp_thermal mlx5_core coretemp kvm_intel kvm nfsd igb irqbypass crct10dif_pclmul devlink crc32_pclmul mei_me joydev ses crc32c_intel enclosure auth_rpcgss i2c_algo_bit ioatdma ptp mei pps_core ghash_clmulni_intel iTCO_wdt iTCO_vendor_support pcspkr dca ipmi_ssif lpc_ich target_core_mod i2c_i801 ipmi_si ipmi_devintf pcc_cpufreq wmi ipmi_msghandler nfs_acl lockd acpi_pad acpi_power_meter grace sunrpc mpt3sas raid_class scsi_transport_sas
[  646.425631] CPU: 1 PID: 2278 Comm: tc Not tainted 4.19.0-rc1+ #799
[  646.432187] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[  646.440595] RIP: 0010:module_put+0x1cb/0x230
[  646.445238] Code: f3 66 94 02 e8 26 ff fa ff 85 c0 74 11 0f b6 1d 51 30 94 02 80 fb 01 77 60 83 e3 01 74 13 65 ff 0d 3a 83 db 73 e9 2b ff ff ff <0f> 0b e9 00 ff ff ff e8 59 01 fb ff 85 c0 75 e4 48 c7 c2 20 62 6b
[  646.464997] RSP: 0018:ffff880354d37068 EFLAGS: 00010286
[  646.470599] RAX: 0000000000000000 RBX: ffffffffc0a52518 RCX: ffffffff8c2668db
[  646.478118] RDX: 0000000000000003 RSI: dffffc0000000000 RDI: ffffffffc0a52518
[  646.485641] RBP: ffffffffc0a52180 R08: fffffbfff814a4a4 R09: fffffbfff814a4a3
[  646.493164] R10: ffffffffc0a5251b R11: fffffbfff814a4a4 R12: 1ffff1006a9a6e0d
[  646.500687] R13: 00000000ffffffff R14: ffff880362bab890 R15: dead000000000100
[  646.508213] FS:  00007f4164c99800(0000) GS:ffff88036fe40000(0000) knlGS:0000000000000000
[  646.516961] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  646.523080] CR2: 00007f41638b8420 CR3: 0000000351df0004 CR4: 00000000001606e0
[  646.530595] Call Trace:
[  646.533408]  ? find_symbol_in_section+0x260/0x260
[  646.538509]  tcf_ife_cleanup+0x11b/0x200 [act_ife]
[  646.543695]  tcf_action_cleanup+0x29/0xa0
[  646.548078]  __tcf_action_put+0x5a/0xb0
[  646.552289]  ? nla_put+0x65/0xe0
[  646.555889]  __tcf_idr_release+0x48/0x60
[  646.560187]  tcf_generic_walker+0x448/0x6b0
[  646.564764]  ? tcf_action_dump_1+0x450/0x450
[  646.569411]  ? __lock_is_held+0x84/0x110
[  646.573720]  ? tcf_ife_walker+0x10c/0x20f [act_ife]
[  646.578982]  tca_action_gd+0x972/0xc40
[  646.583129]  ? tca_get_fill.constprop.17+0x250/0x250
[  646.588471]  ? mark_lock+0xcf/0x980
[  646.592324]  ? check_chain_key+0x140/0x1f0
[  646.596832]  ? debug_show_all_locks+0x240/0x240
[  646.601839]  ? memset+0x1f/0x40
[  646.605350]  ? nla_parse+0xca/0x1a0
[  646.609217]  tc_ctl_action+0x215/0x230
[  646.613339]  ? tcf_action_add+0x220/0x220
[  646.617748]  rtnetlink_rcv_msg+0x56a/0x6d0
[  646.622227]  ? rtnl_fdb_del+0x3f0/0x3f0
[  646.626466]  netlink_rcv_skb+0x18d/0x200
[  646.630752]  ? rtnl_fdb_del+0x3f0/0x3f0
[  646.634959]  ? netlink_ack+0x500/0x500
[  646.639106]  netlink_unicast+0x2d0/0x370
[  646.643409]  ? netlink_attachskb+0x340/0x340
[  646.648050]  ? _copy_from_iter_full+0xe9/0x3e0
[  646.652870]  ? import_iovec+0x11e/0x1c0
[  646.657083]  netlink_sendmsg+0x3b9/0x6a0
[  646.661388]  ? netlink_unicast+0x370/0x370
[  646.665877]  ? netlink_unicast+0x370/0x370
[  646.670351]  sock_sendmsg+0x6b/0x80
[  646.674212]  ___sys_sendmsg+0x4a1/0x520
[  646.678443]  ? copy_msghdr_from_user+0x210/0x210
[  646.683463]  ? lock_downgrade+0x320/0x320
[  646.687849]  ? debug_show_all_locks+0x240/0x240
[  646.692760]  ? do_raw_spin_unlock+0xa2/0x130
[  646.697418]  ? _raw_spin_unlock+0x24/0x30
[  646.701798]  ? __handle_mm_fault+0x1819/0x1c10
[  646.706619]  ? __pmd_alloc+0x320/0x320
[  646.710738]  ? debug_show_all_locks+0x240/0x240
[  646.715649]  ? restore_nameidata+0x7b/0xa0
[  646.720117]  ? check_chain_key+0x140/0x1f0
[  646.724590]  ? check_chain_key+0x140/0x1f0
[  646.729070]  ? __fget_light+0xbc/0xd0
[  646.733121]  ? __sys_sendmsg+0xd7/0x150
[  646.737329]  __sys_sendmsg+0xd7/0x150
[  646.741359]  ? __ia32_sys_shutdown+0x30/0x30
[  646.746003]  ? up_read+0x53/0x90
[  646.749601]  ? __do_page_fault+0x484/0x780
[  646.754105]  ? do_syscall_64+0x1e/0x2c0
[  646.758320]  do_syscall_64+0x72/0x2c0
[  646.762353]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  646.767776] RIP: 0033:0x7f4163872150
[  646.771713] Code: 8b 15 3c 7d 2b 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb cd 66 0f 1f 44 00 00 83 3d b9 d5 2b 00 00 75 10 b8 2e 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 31 c3 48 83 ec 08 e8 be cd 00 00 48 89 04 24
[  646.791474] RSP: 002b:00007ffdef7d6b58 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[  646.799721] RAX: ffffffffffffffda RBX: 0000000000000024 RCX: 00007f4163872150
[  646.807240] RDX: 0000000000000000 RSI: 00007ffdef7d6bd0 RDI: 0000000000000003
[  646.814760] RBP: 000000005b8b9482 R08: 0000000000000001 R09: 0000000000000000
[  646.822286] R10: 00000000000005e7 R11: 0000000000000246 R12: 00007ffdef7dad20
[  646.829807] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000679bc0
[  646.837360] irq event stamp: 6083
[  646.841043] hardirqs last  enabled at (6081): [<ffffffff8c220a7d>] __call_rcu+0x17d/0x500
[  646.849882] hardirqs last disabled at (6083): [<ffffffff8c004f06>] trace_hardirqs_off_thunk+0x1a/0x1c
[  646.859775] softirqs last  enabled at (5968): [<ffffffff8d4004a1>] __do_softirq+0x4a1/0x6ee
[  646.868784] softirqs last disabled at (6082): [<ffffffffc0a78759>] tcf_ife_cleanup+0x39/0x200 [act_ife]
[  646.878845] ---[ end trace b1b8c12ffe51e657 ]---

Fixes: 5ffe57da ("act_ife: fix a potential deadlock")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Addresses-Coverity-ID: 1077614 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Immediately after module_put(), user could delete this
module, so e->ops could be already freed before we call
e->ops->release().

Fix this by moving module_put() after ops->release().

Fixes: ef6980b6 ("introduce IFE action")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Correct the formula for calculating the RQ page remainder,
which should be in byte granularity.  The result will be
non-zero only for RQs smaller than PAGE_SIZE, as an RQ size
is a power of 2.

Divide this by the SQ stride (MLX5_SEND_WQE_BB) to get the
SQ offset in strides granularity.

Fixes: d7037ad7 ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VSC8584 supports 4 LEDs while VSC8531 only supports 2. Let's factorize
the documentation for LED mode properties and give the 4 default values
(the first two being shared between VSC8531 and VSC8584).
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Compatible isn't a required property for PHYs so let's remove it from
the binding DT of the VSC8531 PHYs.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the DT binding, it is specified nowhere that 'vsc8531,led-%d-mode' is
an u8, even though it's read as an u8 in the driver.

Let's update the driver to take into consideration that the
'vsc8531,led-%d-mode' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the DT binding, it is specified nowhere that 'vsc8531,edge-slowdown'
is an u8, even though it's read as an u8 in the driver.

Let's update the driver to take into consideration that the
'vsc8531,edge-slowdown' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the DT binding, it is specified nowhere that 'vsc8531,vddmac' is an
u16, even though it's read as an u16 in the driver.

Let's update the driver to take into consideration that the
'vsc8531,vddmac' property is of the default type u32.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Microsemi PHYs support different LED modes depending on the variant, so
let's factorize the code so we just have to give the supported modes
while the logic behind getting the mode remains identical.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

LEDs modes are set the same way, except they are offset by 4 times the
index of the LED.

Let's factorize all the code so that it's easier to add support for the
4 LEDs of the VSC8584 PHY.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Gounaris says:

====================
Ethernet over hdlc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Added tx timeout handler. This helps
when troubleshooting.
Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following bits in the GUMR is changed for non
tsa mode: CDS, CTSP and CTSS are set to zero.

When set, there is no tx interrupts from the controller.
Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ability to set hmask in the device-tree,
which can be used to change address
filtering of packets.
Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to avoid discarding ethernet
packets when using HDLC_ETH protocol.
Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a need to allow higher indexes to be
able to support MPC83xx platforms. (UCC1-UCC8)
Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2018-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Here are quite a large number of fixes, notably:
 * various A-MSDU building fixes (currently only affects mt76)
 * syzkaller & spectre fixes in hwsim
 * TXQ vs. teardown fix that was causing crashes
 * embed WMM info in reg rule, bad code here had been causing crashes
 * one compilation issue with fix from Arnd (rfkill-gpio includes)
 * fixes for a race and bad data during/after channel switch
 * nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Collect descriptors of all ULD and LLD hardware queues managed
by LLD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

in ndo_set_vf_rate() when max_tx_rate is 0 disable tx
rate limiting for that vf.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>