The 'samsung,vbus-gpio' was submitted before pinmux landed for
exynos5250 and uses the old-style gpio specifier.  Fix the two
exynos5250 boards that use it.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The kernel crashes while resuming from AFTR idle mode. It happens
because L2 cache was not going into retention state.

This patch configures the USE_RETENTION bit of ARM_L2_OPTION register
so that it does not depend on MANUAL_L2RSTDISABLE_CONTROL of
ARM_COMMON_OPTION register for L2RSTDISABLE signal.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Tested-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.10/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:
Omap device tree fixes for issue discovered during the merge window:

- Fix triggering for GPIO interrupts that's needed for 4430sdp
  Ethernet. Otherwise booting with nfsroot won't work.
- Fix CPU operating point values
- Fix wrong assumption that twl PMIC is always connected to omap3
- Add gpmc for am33xx so beaglebone users can use the bus
- Cosmetic fix for mcspi pin muxing to avoid confusion

* tag 'omap-for-v3.10/dt-fixes-for-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: don't assume boards are using twl4030 for omap3
  ARM: dts: Configure and fix the McSPI pins for 4430sdp
  ARM: dts: AM33XX: Add GPMC node
  ARM: dts: OMAP4460: Fix CPU OPP voltages
  ARM: dts: OMAP36xx: Fix CPU OPP voltages
  ARM: dts: OMAP4: Fix ethernet IRQ for OMAP4 boards

Merge tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:
Omap fixes for things that were discovered during the merge window:

- Few GPMC fixes and binding doc updates noted after sending
  pull requests for the GPMC branch.
- Board fixes for beagle usb host and rx51 spi probe order
- SoC fixes dt earlyprintk, omap1 dma and omap2+ id.c error
  handling fixes

Then few minor things that are not strictly fixes but are good
to get out of the way:

- Add missing legacy mux registers for am/dm73x gpio
- Add detection for am33xx pg2.1 silicon
- Enable twl4030 audio modules in defconfig

* tag 'omap-for-v3.10/fixes-for-merge-window-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Remove bogus IS_ERR_OR_NULL checking from id.c
  ARM: OMAP4+: omap2plus_defconfig: Enable audio via TWL6040 as module
  ARM: OMAP2: AM33XX: id: Add support for new AM335x PG2.1 Si
  omap: mux: add AM/DM37x gpios
  ARM: OMAP1: DMA: fix error handling in omap1_system_dma_init()
  ARM: OMAP2+: omap_device: use late_initcall_sync
  ARM: OMAP: RX-51: change probe order of touchscreen and panel SPI devices
  ARM: OMAP3: Beagle: Fix USB Host on beagle xM Ax/Bx
  ARM: OMAP2+: only WARN if a GPMC child probe function fail
  ARM: OMAP2+: only search for GPMC DT child nodes on probe
  Documentation: dt: update properties in TI GPMC NAND example
  Documentation: dt: update TI GPMC ethernet binding properties
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/mach-ux500/board-mop500.c: In function ‘mop500_prox_activate’:
arch/arm/mach-ux500/board-mop500.c:406:18: warning: ignoring return value of
        ‘regulator_enable’, declared with attribute warn_unused_result
        [-Wunused-result]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Fix db8500_read_soc_id() to read all five soc_id number locations
instead of repeating the second one two times.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Trivial patch, adding the i2c Cypress trackpad used on Snow.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>

commit 6cd2c7db (videomode: videomode_from_timing work) changed the name of
the function from videomode_from_timing() to videomode_from_timings().

commit 32ed6ef1 (videomode: create enum for videomode's display flags) changed
the 'data_flags' field in videomode structure to 'flags'

Adapt to these changes in order to fix the following errors:

drivers/video/mxsfb.c:761:3: error: too many arguments to function 'videomode_from_timing'
drivers/video/mxsfb.c:761:7: error: void value not ignored as it ought to be
drivers/video/mxsfb.c:768:9: error: 'struct videomode' has no member named 'data_flags'
drivers/video/mxsfb.c:770:9: error: 'struct videomode' has no member named 'data_flags'

Also, select VIDEOMODE_HELPER instead of OF_VIDEOMODE, as this one is
deprecated.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Since commit 657eee7d (media: coda: use genalloc API) the following build
error happens with imx_v4_v5_defconfig:

drivers/built-in.o: In function 'coda_remove':
clk-composite.c:(.text+0x112180): undefined reference to 'gen_pool_free'
drivers/built-in.o: In function 'coda_probe':
clk-composite.c:(.text+0x112310): undefined reference to 'of_get_named_gen_pool'
clk-composite.c:(.text+0x1123f4): undefined reference to 'gen_pool_alloc'
clk-composite.c:(.text+0x11240c): undefined reference to 'gen_pool_virt_to_phys'
clk-composite.c:(.text+0x112458): undefined reference to 'dev_get_gen_pool'

Select GENERIC_ALLOCATOR and get rid of the custom IRAM_ALLOC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Commit bca7a5a0 (ARM: cpu hotplug: remove majority of cache flushing
from platforms) removes include of <asm/cacheflush.h> and hence
discovers a few indirect inclusion and declaration problems as below.

  CC      arch/arm/mach-imx/hotplug.o
In file included from arch/arm/mach-imx/hotplug.c:16:0:
arch/arm/mach-imx/common.h:100:29: warning: ‘struct pt_regs’ declared inside parameter list [enabled by default]
arch/arm/mach-imx/common.h:100:29: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
arch/arm/mach-imx/common.h:101:29: warning: ‘struct pt_regs’ declared inside parameter list [enabled by default]
arch/arm/mach-imx/hotplug.c: In function ‘imx_cpu_die’:
arch/arm/mach-imx/hotplug.c:53:2: error: implicit declaration of function ‘cpu_do_idle’ [-Werror=implicit-function-declaration]
arch/arm/mach-imx/hotplug.c: In function ‘imx_cpu_kill’:
arch/arm/mach-imx/hotplug.c:58:26: error: ‘jiffies’ undeclared (first use in this function)
arch/arm/mach-imx/hotplug.c:58:26: note: each undeclared identifier is reported only once for each function it appears in
arch/arm/mach-imx/hotplug.c:58:2: error: implicit declaration of function ‘msecs_to_jiffies’ [-Werror=implicit-function-declaration]
arch/arm/mach-imx/hotplug.c:61:3: error: implicit declaration of function ‘time_after’ [-Werror=implicit-function-declaration]

Fix them by adding the needed inclusion and declaration.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

* late/fixes:
  ARM: OMAP2+: Fix unmet direct dependencies for SERIAL_OMAP
  ARM: ux500: always select ABX500_CORE
  ARM: SIRF: select SMP_ON_UP only on SMP builds
  ARM: SPEAr: conditionalize l2x0 support
  ARM: imx: build CPU suspend code only when needed
  ARM: OMAP: build SMP code only for OMAP4/5
  ARM: tegra: Tegra114 needs CPU_FREQ_TABLE
  ARM: default machine descriptor for multiplatform
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull more NFS client bugfixes from Trond Myklebust:

 - Ensure that we match the 'sec=' mount flavour against the server list

 - Fix the NFSv4 byte range locking in the presence of delegations

 - Ensure that we conform to the NFSv4.1 spec w.r.t.  freeing lock
   stateids

 - Fix a pNFS data server connection race

* tag 'nfs-for-3.10-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS4.1 Fix data server connection race
  NFSv3: match sec= flavor against server list
  NFSv4.1: Ensure that we free the lock stateid on the server
  NFSv4: Convert nfs41_free_stateid to use an asynchronous RPC call
  SUNRPC: Don't spam syslog with "Pseudoflavor not found" messages
  NFSv4.x: Fix handling of partially delegated locks

Pull networking update from David Miller:

 1) Propagate return error values properly in irda, spider_net, sfc, and
    bfin_mac.  From Wei Yongjun.

 2) Fix fec driver OOPS on rapid link up/down, from Frank Li.

 3) FIX VF resource allocation and chip message payload length errors in
    be2net driver, from Sathya Perla.

 4) Fix inner protocol inspection during GSO from Pravin B Shelar.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  if_cablemodem.h: Add parenthesis around ioctl macros
  gso: Handle Trans-Ether-Bridging protocol in skb_network_protocol()
  net: fec: fix kernel oops when plug/unplug cable many times
  bfin_mac: fix error return code in bfin_mac_probe()
  sfc: fix return value check in efx_ptp_probe_channel()
  net/spider_net: fix error return code in spider_net_open()
  net/irda: fix error return code in bfin_sir_open()
  net: of_mdio: fix behavior on missing phy device
  sierra_net: keep status interrupt URB active
  usbnet: allow status interrupt URB to always be active
  qmi_wwan/cdc_ether: add device IDs for Dell 5804 (Novatel E371) WWAN card
  be2net: disable TX in be_close()
  be2net: fix EQ from getting full while cleaning RX CQ
  be2net: fix payload_len value for GET_MAC_LIST cmd req
  be2net: provision VF resources before enabling SR-IOV

Pull PCI updates from Bjorn Helgaas:
 "MSI:
      PCI: Set ->mask_pos correctly
  Hotplug:
      PCI: Delay final fixups until resources are assigned
  Moorestown:
      x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0"

* tag 'pci-v3.10-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Delay final fixups until resources are assigned
  x86/pci/mrst: Use configuration mechanism 1 for 00:00.0, 00:02.0, 00:03.0
  PCI: Set ->mask_pos correctly

Pull MTD update from David Woodhouse:

 - Lots of cleanups from Artem, including deletion of some obsolete
   drivers

 - Support partitions larger than 4GiB in device tree

 - Support for new SPI chips

* tag 'for-linus-20130509' of git://git.infradead.org/linux-mtd: (83 commits)
  mtd: omap2: Use module_platform_driver()
  mtd: bf5xx_nand: Use module_platform_driver()
  mtd: denali_dt: Remove redundant use of of_match_ptr
  mtd: denali_dt: Change return value to fix smatch warning
  mtd: denali_dt: Use module_platform_driver()
  mtd: denali_dt: Fix incorrect error check
  mtd: nand: subpage write support for hardware based ECC schemes
  mtd: omap2: use msecs_to_jiffies()
  mtd: nand_ids: use size macros
  mtd: nand_ids: improve LEGACY_ID_NAND macro a bit
  mtd: add 4 Toshiba nand chips for the full-id case
  mtd: add the support to parse out the full-id nand type
  mtd: add new fields to nand_flash_dev{}
  mtd: sh_flctl: Use of_match_ptr() macro
  mtd: gpio: Use of_match_ptr() macro
  mtd: gpio: Use devm_kzalloc()
  mtd: davinci_nand: Use of_match_ptr()
  mtd: dataflash: Use of_match_ptr() macro
  mtd: remove h720x flash support
  mtd: onenand: remove OneNAND simulator
  ...

Pull firewure updates from Stefan Richter:
  - fix controller removal when controller is in suspended state
  - fix video reception on VIA VT6306 with gstreamer, MythTV, and maybe dv4l
  - fix a startup issue with Agere/LSI FW643-e2
  - error logging improvements and other small updates

* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: ohci: dump_stack() for PHY regs read/write failures
  firewire: ohci: Improve bus reset error messages
  firewire: ohci: Alias dev_* log functions
  firewire: ohci: Fix 'failed to read phy reg' on FW643 rev8
  firewire: ohci: fix VIA VT6306 video reception
  firewire: ohci: Check LPS before register access on pci removal
  firewire: ohci: Fix double free_irq()
  firewire: remove unnecessary alloc/OOM messages
  firewire: sbp2: replace BUG_ON by WARN_ON
  firewire: core: remove an always false test
  firewire: Remove two unneeded checks for macros

Pull two small EDAC fixes from Borislav Petkov.

* tag 'edac_fixes_for_3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  EDAC: Don't give write permission to read-only files
  EDAC, mc_sysfs.c: Fix string array pointer types

Pull watchdog update from Wim Van Sebroeck:
 "Fix a kdump issue in hpwdt and a possible NULL dereference"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: Fix race condition in registration code
  watchdog: Convert to devm_ioremap_resource()

Pull removal of GENERIC_GPIO from Grant Likely:
 "GENERIC_GPIO now synonymous with GPIOLIB.  There are no longer any
  valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
  is possible to do so which has been causing confusion and breakage.
  This branch does the work to completely eliminate GENERIC_GPIO."

* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
  gpio: update gpio Chinese documentation
  Remove GENERIC_GPIO config option
  Convert selectors of GENERIC_GPIO to GPIOLIB
  blackfin: force use of gpiolib
  m68k: coldfire: use gpiolib
  mips: pnx833x: remove requirement for GENERIC_GPIO
  openrisc: default GENERIC_GPIO to false
  avr32: default GENERIC_GPIO to false
  xtensa: remove explicit selection of GENERIC_GPIO
  sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
  powerpc: remove redundant GENERIC_GPIO selection
  unicore32: default GENERIC_GPIO to false
  unicore32: remove unneeded select GENERIC_GPIO
  arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
  arm: remove redundant GENERIC_GPIO selection
  mips: alchemy: require gpiolib
  mips: txx9: change GENERIC_GPIO to GPIOLIB
  mips: loongson: use GPIO driver on CONFIG_GPIOLIB
  mips: remove redundant GENERIC_GPIO select

Pull slave-dmaengine updates from Vinod Koul:
 "This time we have dmatest improvements from Andy along with dw_dmac
  fixes.  He has also done support for acpi for dmanegine.

  Also we have bunch of fixes going in DT support for dmanegine for
  various folks.  Then Haswell and other ioat changes from Dave and
  SUDMAC support from Shimoda."

* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (53 commits)
  dma: tegra: implement suspend/resume callbacks
  dma:of: Use a mutex to protect the of_dma_list
  dma: of: Fix of_node reference leak
  dmaengine: sirf: move driver init from module_init to subsys_initcall
  sudmac: add support for SUDMAC
  dma: sh: add Kconfig
  at_hdmac: move to generic DMA binding
  ioatdma: ioat3_alloc_sed can be static
  ioatdma: Adding write back descriptor error status support for ioatdma 3.3
  ioatdma: S1200 platforms ioatdma channel 2 and 3 falsely advertise RAID cap
  ioatdma: Adding support for 16 src PQ ops and super extended descriptors
  ioatdma: Removing hw bug workaround for CB3.x .2 and earlier
  dw_dmac: add ACPI support
  dmaengine: call acpi_dma_request_slave_channel as well
  dma: acpi-dma: introduce ACPI DMA helpers
  dma: of: Remove unnecessary list_empty check
  DMA: OF: Check properties value before running be32_to_cpup() on it
  DMA: of: Constant names
  ioatdma: skip silicon bug workaround for pq_align for cb3.3
  ioatdma: Removing PQ val disable for cb3.3
  ...

Pull thermal management update from Zhang Rui:
 "The most important one is to build thermal core and governor and cpu
  cooling code into one module.  This fixes a regression that thermal
  core does not work if it is built as module, since 3.7.  I'll backport
  them to stable kernel once those changes are in upstream.

  The largest batch is the thermal kernel-doc & coding style
  updates/cleanups from Eduardo.

  Highlights:

   - build all thermal framework code into one module to fix a
     regression that thermal does not work if it is built as module.

   - Marvell Armada 370/XP thermal sensor driver

   - thermal core/cpu cooling kernel-doc & coding style updates and
     cleanups.

   - Add Eduardo Valentin as thermal sub-maintainer, both in mailing
     list and patchwork.  He will help me on arm thermal drivers."

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (68 commits)
  thermal: db8500_cpufreq_cooling: remove usage of IS_ERR_OR_NULL()
  thermal: thermal_core: remove usage of IS_ERR_OR_NULL
  thermal: cpu_cooling: improve line breaking
  thermal: cpu_cooling: alignment improvements
  thermal: cpu_cooling: remove checkpatch.pl warning
  thermal: cpu_cooling: remove trailing blank line
  thermal: cpu_cooling: align on open parenthesis
  thermal: cpu_cooling: standardize comment style
  thermal: cpu_cooling: standardize end of function
  thermal: cpu_cooling: remove trailing white spaces
  Thermal: update documentation for thermal_zone_device_register
  thermal: update kernel-doc for thermal_zone_device_register
  thermal: update kernel-doc for create_trip_attrs
  thermal: update kernel-doc for thermal_cooling_device_register
  thermal: update kernel-doc for thermal_zone_unbind_cooling_device
  thermal: update kernel-doc for thermal_zone_bind_cooling_device
  thermal: use EXPORT_SYMBOL_GPL
  thermal: rename notify_thermal_framework to thermal_notify_framework
  thermal: update driver license
  thermal: use strlcpy instead of strcpy
  ...

If a board isn't using twl4030, then dtc will complain about the missing
phandle (which is in twl4030.dtsi).  Move the phy declaration to the dts
files.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 6770b211 (ARM: OMAP2+: Export SoC information to userspace)
had some broken return value handling as noted by Russell King:

+       soc_dev = soc_device_register(soc_dev_attr);
+       if (IS_ERR_OR_NULL(soc_dev)) {
+               kfree(soc_dev_attr);
+               return;
+       }
+
+       parent = soc_device_to_device(soc_dev);
+       if (!IS_ERR_OR_NULL(parent))
+               device_create_file(parent, &omap_soc_attr);

This is nonsense.  For the first, IS_ERR() is sufficient.  For the second,
tell me what error checking is required in the return value of this
function:

struct device *soc_device_to_device(struct soc_device *soc_dev)
{
        return &soc_dev->dev;
}

when you've already determined that the passed soc_dev is a valid pointer.
If you read the comments against the prototype:

/**
 * soc_device_to_device - helper function to fetch struct device
 * @soc: Previously registered SoC device container
 */
struct device *soc_device_to_device(struct soc_device *soc);

if "soc" is valid, it means the "previously registered SoC device container"
must have succeeded and that can only happen if the struct device has been
registered.  Ergo, there will always be a valid struct device pointer for
any registered SoC device container.  Therefore, if soc_device_register()
succeeds, then the return value from soc_device_to_device() will always be
valid and no error checking of it is required.

Simples.  The rule as ever applies here: get to know the APIs your using
and don't fumble around in the dark hoping that you'll get this stuff
right.

Fix it as noted by Russell.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

I get the following warning on boot:

------------[ cut here ]------------
WARNING: at drivers/base/core.c:575 device_create_file+0x9a/0xa0()
Hardware name:  -[8737R2A]-
Write permission without 'store'
...
</snip>

Drilling down, this is related to dynamic channel ce_count attribute
files sporting a S_IWUSR mode without a ->store() function. Looking
around, it appears that they aren't supposed to have a ->store()
function. So remove the bogus write permission to get rid of the
warning.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: <stable@vger.kernel.org> # 3.[89]
[ shorten commit message ]
Signed-off-by: Borislav Petkov <bp@suse.de>

A race condition exists when registering the first watchdog device.
Sequence of events:

- watchdog_register_device calls watchdog_dev_register
- watchdog_dev_register creates the watchdog misc device by calling
  misc_register.
  At that time, the matching character device (/dev/watchdog0) does not yet
  exist, and old_wdd is not set either.
- Userspace gets an event and opens /dev/watchdog
- watchdog_open is called and sets wdd = old_wdd, which is still NULL,
  and tries to dereference it. This causes the kernel to panic.

Seen with systemd trying to open /dev/watchdog immediately after
it was created.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

The bootloader configures the pins, but has pull bits
set without pull enable bits. While this is harmless,
and won't do anything, it seems to cause confusion at
least for me every time looking at the pin configuration.
Fix it for DT based boot.
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add GPMC data node to AM33XX device tree file.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

commit d16fb25d (ARM: dts: OMAP4460: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP4460 OPP data in
arch/arm/mach-omap2/opp4xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

commit 3027e267 (ARM: dts: OMAP36xx: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP36xx OPP data in
arch/arm/mach-omap2/opp3xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Boards supported upstream all use TWL6040 as audio codec, enable the common
ASoC machine driver by default for them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for chip id detection of AM335x PG2.1 Silicon.

Currently omap3xxx_check_revision() detects PG1.0 and PG2.0 only,
this patch extends it by adding PG2.1 Si support.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch adds GPIO pins found on AM/DM37x.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the missing iounmap() before return from omap1_system_dma_init()
in the error handling case.
Also removed platform_device_del() on add resources error case which
cause dup device delete.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>

If DEBUG_LL and earlyprintk are enabled, and omap-serial.c is compiled
as a module, the kernel boot hangs early as the clocks for serial port
are cut while earlyprintk still uses the port.

The problem is a race between the late_initcall for omap_device (which
idles devices that have no drivers) and the late_initcall in
kernel/printk.c which turns off the earlyconsole.   Any printks
that happen between this omap_device late initcall and the earlyconsole
late initcall will crash when accessing the UART.

The fix is to ensure the omap_device initcall happens after the
earlyconsole initcall.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Commit 9fdca9df (spi: omap2-mcspi: convert to module_platform_driver)
broke the SPI display/panel driver probe on RX-51/N900. The exact cause is
not fully understood, but it seems to be related to the probe order. SPI
communication to the panel driver (spi1.2) fails unless the touchscreen
(spi1.0) has been probed/initialized before. When the omap2-mcspi driver
was converted to a platform driver, it resulted in that the devices are
probed immediately after the board registers them in the order they are
listed in the board file.

Fix the issue by moving the touchscreen before the panel in the SPI
device list.

The patch fixes the following failure:

[    1.260955] acx565akm spi1.2: invalid display ID
[    1.265899] panel-acx565akm display0: acx_panel_probe panel detect error
[    1.273071] omapdss CORE error: driver probe failed: -19
Tested-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Joni Lapilainen <joni.lapilainen@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>

On Beagle xM Rev. Ax/Bx, the USB power enable GPIO logic is
reversed when compared to other revisions i.e. it is
active high instead of active low.

Use the beagle_config.usb_pwr_level flag correctly so that
the power regulator can be configured at runtime.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull InfiniBand/RDMA changes from Roland Dreier:
 - XRC transport fixes
 - Fix DHCP on IPoIB
 - mlx4 preparations for flow steering
 - iSER fixes
 - miscellaneous other fixes

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (23 commits)
  IB/iser: Add support for iser CM REQ additional info
  IB/iser: Return error to upper layers on EAGAIN registration failures
  IB/iser: Move informational messages from error to info level
  IB/iser: Add module version
  mlx4_core: Expose a few helpers to fill DMFS HW strucutures
  mlx4_core: Directly expose fields of DMFS HW rule control segment
  mlx4_core: Change a few DMFS fields names to match firmare spec
  mlx4: Match DMFS promiscuous field names to firmware spec
  mlx4_core: Move DMFS HW structs to common header file
  IB/mlx4: Set link type for RAW PACKET QPs in the QP context
  IB/mlx4: Disable VLAN stripping for RAW PACKET QPs
  mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level
  RDMA/iwcm: Don't touch cmid after dropping reference
  IB/qib: Correct qib_verbs_register_sysfs() error handling
  IB/ipath: Correct ipath_verbs_register_sysfs() error handling
  RDMA/cxgb4: Fix SQ allocation when on-chip SQ is disabled
  SRPT: Fix odd use of WARN_ON()
  IPoIB: Fix ipoib_hard_header() return value
  RDMA: Rename random32() to prandom_u32()
  RDMA/cxgb3: Fix uninitialized variable
  ...

Pull arm64 update from Catalin Marinas:

 - Since drivers/irqchip/irq-gic.c no longer has dependencies on arm32
   specifics (the 'gic' branch merged), it can be enabled on arm64.

 - Enable arm64 support for poweroff/restart (for code under
   drivers/power/reset/).

 - Fixes (dts file, exception handling, bitops)

* tag 'arm64-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
  arm64: Treat the bitops index argument as an 'int'
  arm64: Ignore the 'write' ESR flag on cache maintenance faults
  arm64: dts: fix #address-cells for foundation-v8
  arm64: vexpress: Add support for poweroff/restart
  arm64: Enable support for the ARM GIC interrupt controller