- 27 Feb, 2009 40 commits
-
-
Michael Buesch authored
Move the DMA stop sanity check up a few lines, so it's actually theoretically possible to trigger. (But it still shouldn't trigger, of course). Signed-off-by:
Michael Buesch <mb@bu3sch.de> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Vasanthakumar Thiagarajan authored
Passing beacons received from other BSS to s/w in non-scanning state is unnecessary in STA mode. This patch filters them out in h/w. Signed-off-by:
Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by:
-
Fenghua Yu authored
When iwlwifi runs on IOMMU, IOMMU generates a lot of PTE write faults because PTE write bit is not set on some of PTE's. This is because iwlwifi driver calls DMA mapping with PCI_DMA_TODEVICE which is read only in mapping PTE. But iwlwifi device actually writes to the mapped page to update its contents. This issue is not exposed in swiotlb. But VT-d hardware can capture this fault and stop the fault transaction. The iwl TX command contains a scratch field that is updated by uCode to indicate retry counts. For 5000 series the patch is required also for regular frames, but this patch does not differenciate. Signed-off-by:
Fenghua Yu <fenghua.yu@intel.com> Acked-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Reinette Chatre <reinette.chatre@intel.com> Signed-off-by:
-
Abhijeet Kolekar authored
Patch unifies use of SW rfkill between 3945 and agn driver. Signed-off-by:
Abhijeet Kolekar <abhijeet.kolekar@intel.com> Acked-by:
Samuel Ortiz <samuel.ortiz@intel.com> Signed-off-by:
-
Abhijeet Kolekar authored
iwl3945 uses iwl_isr and deletes duplicated iwl3945_isr. Signed-off-by:
-
Abhijeet Kolekar authored
Patch removes duplicate code to enable and disable interrupt. iwl3945 now uses iwlwifi's functions. Signed-off-by:
-
Abhijeet Kolekar authored
Patch removes duplicate code from iwl3945 and uses iwl_rx_reply_error and spectrum notifications from iwlwifi. Signed-off-by:
-
Abhijeet Kolekar authored
Patch removes duplicate rx handlers(pm_sleep and pm_debug) from 3945 and uses handlers from iwlwifi. Signed-off-by:
-
Abhijeet Kolekar authored
3945 can use iwl_mac_hw_scan callback instead of iwl3945_mac_hw_scan callback. Signed-off-by:
-
Abhijeet Kolekar authored
Patch makes use of iwl_rx_scan handler for 3945. Signed-off-by:
-
Jason Andryuk authored
at76_debug should be an unsigned int as it used as a bit field. In fact, modprobe fails when trying to set at76_debug's high bit. Signed-off-by:
Jason Andryuk <jandryuk@gmail.com> Signed-off-by:
Kalle Valo <kalle.valo@iki.fi> Signed-off-by:
-
Jason Andryuk authored
With the latest mac80211 stack, the driver needs to be updated for cfg80211 scanning. I based the changes off of modifications for at76_usb found here: http://johannes.sipsolutions.net/patches/old/all/2008-09-19-13:35/020-cfg80211-scan.patch The trick was that max_signal also needs to be set to avoid a divide by zero Oops. I just guessed and used the value 100 for now. kvalo: handpicked the change from two different patches Signed-off-by:
-
Kalle Valo authored
This is a driver for usb devices based on at76c50x chipset. This is a mac80211 port of the original at76_usb driver. Signed-off-by:
-
John W. Linville authored
Default to MAX_UCODE_BEACON_INTERVAL if the output of iwl_adjust_beacon_interval would otherwise be zero. This prevents a division by zero on my iwl5300-equipped Lenovo T400 with kernels that include "mac80211: use cfg80211s BSS infrastructure". This patch is a bit of a hack -- I'm not sure why iwl_setup_rxon_timing is giving iwl_adjust_beacon_interval a zero input (which is the only way it would output zero). I would be happy to have a better fix. But for now, this makes my box boot... Signed-off-by: -
Roel Kluin authored
This patch expands the parenthesis in the txctl reg write of the LO calibration to enforce precedence rules. Signed-off-by:
Roel Kluin <roel.kluin@gmail.com> Signed-off-by:
-
Roel Kluin authored
Only FIF_FCSFAIL is set due to parentheses Signed-off-by:
-
Dan Williams authored
Scanned BSS entries are timestamped with jiffies, which doesn't increment across suspend and hibernate. On resume, every BSS in the scan list looks like it was scanned within the last 10 seconds, irregardless of how long the machine was actually asleep. Age scan results on resume with the time spent during sleep so userspace has a clue how old they really are. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
John W. Linville authored
Signed-off-by: -
Johannes Berg authored
The previous patch made cfg80211 generally aware of the signal type a given hardware will give, so now it can implement SIOCGIWRANGE itself, removing more wext stuff from mac80211. Might need to be a little more parametrized once we have more hardware using cfg80211 and new hardware capabilities. Signed-off-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
-
Johannes Berg authored
It wasn't a good idea to make the signal type a per-BSS option, although then it is closer to the actual value. Move it to be a per-wiphy setting, update mac80211 to match. Signed-off-by:
-
Johannes Berg authored
There's no particular reason to not let untrusted users see this information -- it's just the stations we're talking to, packet counters for them and possibly some mesh things. Signed-off-by:
-
Johannes Berg authored
Document the new shutdown member. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Some APs don't start BA negotiation with the client before it is done with the key handshake in WPA/RSN. With those APs, key handshake times out if EAPOL frames are sent after addba request. So defer the BA negotiation until we are done with tx/rx of all EAPOL frames. Signed-off-by:
-
Johannes Berg authored
Due to various bugs in the software stack we end up having to fill qual.qual; level should be used, but wpa_supplicant doesn't properly ignore qual.qual, NM should use qual.level regardless of that because qual.qual is 0 but doesn't handle IW_QUAL_DBM right now. So fill qual.qual with the qual.level value clamped to -110..-40 dBm or just the regular 'unspecified' signal level. This requires a mac80211 change to properly announce the max_qual.qual and avg_qual.qual values. Signed-off-by:
-
Dan Williams authored
Scanned BSS entries are timestamped with jiffies, which doesn't increment across suspend and hibernate. On resume, every BSS in the scan list looks like it was scanned within the last 10 seconds, irregardless of how long the machine was actually asleep. Age scan results on resume with the time spent during sleep so userspace has a clue how old they really are. Signed-off-by:
-
Ivo van Doorn authored
The word_base is in bytes instead of word index number, this means that when using it, it should be transformed into a word index first. Otherwise RF register reading will fail through debugfs since we would start reading 4 words starting with word 4 (which is the last valid word for RF). Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by:
-
Jouni Malinen authored
The TX/RX packet counters are needed to fill in RADIUS Accounting attributes Acct-Output-Packets and Acct-Input-Packets. We already collect the needed information, but only the TX/RX bytes were previously exposed through nl80211. Allow applications to fetch the packet counters, too, to provide more complete support for accounting. Signed-off-by:
Jouni Malinen <jouni.malinen@atheros.com> Acked-by:
-
Sujith authored
Setting up the CAB queue requires only the beacon interval, remove the function ath_get_beaconconfig() which is redundant. Signed-off-by:
Sujith <Sujith.Manoharan@atheros.com> Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
Set channel change time to 5ms, this will improve scan results. Signed-off-by:
-
Jouni Malinen authored
This extends the NL80211_CMD_TRIGGER_SCAN command to allow applications to specify a set of information element(s) to be added into Probe Request frames with NL80211_ATTR_IE. This provides support for the MLME-SCAN.request primitive parameter VendorSpecificInfo and can be used, e.g., to implement WPS scanning. Signed-off-by:
-
Sujith authored
Signed-off-by:
-
Sujith authored
RX and calibration have different timeout requirements. This patch fixes it by changing the HW wait routine to accept a timeout value. Signed-off-by:
-
Sujith authored
This patch programs the RTC registers of AR9100 chipsets correctly during chip reset. Signed-off-by:
-
Bob Copeland authored
RTS and CTS-to-self duration needs to go after ICV len is considered. Changes-licensed-under: 3-Clause-BSD Signed-off-by:
Bob Copeland <me@bobcopeland.com> Signed-off-by:
-
Bob Copeland authored
We currently send beacons directly from the interrupt routine. This can hold up interrupt processing in beaconing modes and makes the ISR somewhat more complex. Move it to a tasklet like rx and tx. Changes-licensed-under: 3-Clause-BSD Signed-off-by:
-
Bob Copeland authored
ath5k_reset can be called from process context, which in turn can call ath5k_beacon_config which takes the sc->block spinlock. Since it can also be taken in hard irq context, use spin_lock_irqsave everywhere. This fixes a potential deadlock in adhoc mode. Changes-licensed-under: 3-Clause-BSD Cc: stable@kernel.org Signed-off-by:
-
Bob Copeland authored
Since interrupts are already masked by the hardware, there's no need to discard interrupt bits in the ISR itself. Also, in ath5k_beacon_config we mask off a couple of bits without locking, so doing this mask in software can lead to unhandled beacon timer and beacon miss interrupts. Changes-licensed-under: 3-Clause-BSD Signed-off-by:
-
Ivo van Doorn authored
Signed-off-by:
-
