Instead of memcpy() from a static array, just use
the new helper function eth_broadcast_addr().
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of allocating one big chunk of DMA-coherent
memory for the firmware and keeping it around, only
vmalloc() the firmware and copy it into a single
page of DMA-coherent memory for the upload.

The advantage is that we don't need DMA memory for
the firmware image that is stored while the driver
is operating, we only need it while uploading.

This will make it easier for the driver to work if
the system has fragmented memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When we kill the radio with the RF kill button we could access
the HW after having stopped the APM which would result in the
warning below.

The flow goes like this:
* RF kill
	iwlwifi notifies the stack which stops the driver
	fw sends CARD_STATE_NOTIFICATION
* iwl_trans_pcie_stop_device stops the APM
* the tasklet runs and calls to iwl_rx_handle
* iwl_rx_handle calls iwl_rx_queue_restock
* iwl_rx_queue_restock tries to access the HW...

[255908.543823] ------------[ cut here ]------------
[255908.543843] WARNING: at drivers/net/wireless/iwlwifi/iwl-io.c:150 iwl_grab_nic_access+0x79/0xb0 [iwlwifi]()
[255908.543849] Hardware name: Latitude E6410
[255908.543852] Timeout waiting for hardware access (CSR_GP_CNTRL 0x000003d8)
[255908.543856] Modules linked in: iwlmvm iwlwifi mac80211 [...]
[255908.543935] Pid: 0, comm: swapper Tainted: G        W   3.1.0 #1
[255908.543939] Call Trace:
[255908.543950]  [<c1046e42>] warn_slowpath_common+0x72/0xa0
[255908.543980]  [<c1046f13>] warn_slowpath_fmt+0x33/0x40
[255908.543992]  [<fa4bb3b9>] iwl_grab_nic_access+0x79/0xb0 [iwlwifi]
[255908.544004]  [<fa4bb9eb>] iwl_write_direct32+0x2b/0xa0 [iwlwifi]
[255908.544018]  [<fa4c0ff9>] iwl_rx_queue_update_write_ptr+0x89/0x1d0 [iwlwifi]
[255908.544054]  [<fa4c1250>] iwlagn_rx_queue_restock+0x110/0x140 [iwlwifi]
[255908.544067]  [<fa4c234d>] iwl_irq_tasklet+0x82d/0xf40 [iwlwifi]
[255908.544096]  [<c104e11e>] tasklet_action+0xbe/0x100
[255908.544102]  [<c104d91e>] __do_softirq+0xae/0x1f0
[255908.544227] ---[ end trace d150f49345d85009 ]---

Prevent this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Remove outdated iwlagn prefix to a few functions and fix comments
that were not accurate.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's a block of code that's indented too
far, move it out to where it should be.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If an RX interrupt is signalled after or during apm_stop
we may try to access the peripherals which are already
down. Prevent this by disabling interrupts first.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

iwl_disable_interupts() already resets the register, no
need to do it again.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

These stubs are from internal experimental code
and aren't needed in the driver in the kernel
so just remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

No one uses it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Amit Beka <amit.beka@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Tracing commands builds an array of trace data
items even when the tracepoint is disabled.
Instead, loop in the tracepoint assignment.

This reduces overhead if tracing is compiled
into the driver but not enabled and slightly
reduces overall driver size as well:

   text	   data	    bss	    dec	    hex	filename
 114514	   6509	     48	 121071	  1d8ef	before/iwlwifi.ko
 114189	   6509	     48	 120746	  1d7aa	after/iwlwifi.ko
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since the firmware will give us an A-MPDU bit and
only a single PHY information packet for all the
subframes in an A-MPDU, we can easily report the
minimal A-MPDU information for radiotap.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The device only supports a maximum of three
antennas, and only three bits are used, the
fourth bit is the A-MPDU indicator.

The only consequence of this is reporting
invalid information in radiotap, so this
isn't an important change.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Commit mac80211: avoid using synchronize_rcu in ieee80211_set_probe_resp
changed the return value when the probe response template is not present.
Revert to the earlier value of 1 - this fixes AP mode for drivers like
ath9k.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Because the hardware reports whenever an frame
was either at the start, in the middle or at
the end of a A-MPDU, we can easily report the
information for radiotap.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In case of changes in the supported rates set for a given station, it is now
possible to use this callback to update the current internal state of the
station in the htc driver.
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Conflicts:
	drivers/net/wireless/mac80211_hwsim.c

This reverts commit 2e48928d.

Those functions are needed and should not be removed, or
there is no way to set the rfkill led trigger name.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When unregistered with mac80211, we can't call its functionality
for FW restart, so avoid it and prevent automatic FW restart for
the init firmware.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There is no need to check if the ownership has been
relinquished but we should rather try to get it in a
loop.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no need to carry around a return value
that is always NETDEV_TX_OK anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In multi-channel scenarios, the channel that we will
transmit a probe request on isn't always the current
channel (which will be NULL anyway) but will instead
be the channel that the AP is on. Pass the channel
to the ieee80211_send_probe_req() function so it can
be used in the different scenarios. The scan code
continues to pass the current channel, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no need to BUG_ON when a driver registers
invalid operations, warn and return an error.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The optimisation of scanning only on the current
channel should check the operating channel. Also
modify it to compare channel pointer rather than
the frequency.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Even for single-channel devices it is possible that we
switch the channel temporarily (e.g. for scanning) but
while doing so process a received frame that was still
received on the old channel, so checking the current
band is racy. Use the band from status instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

With the move to multi-channel and away from
drv_config(), hw.conf.channel will not always
be set, only for devices using the current API
instead of the new channel context APIs. Check
the channel is set before adding its frequency
to the trace data.

Also break some overly long lines in the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Using hw.conf.channel is wrong as it could be the
temporary channel if the station is added from the
workqueue while the device is already on another
channel. Use oper_channel instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

You can now get these values through iw, and
they conflict with multi-channel work.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In ieee80211_beacon_get_tim() we can use the
txrc.sband instead of a separate local variable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Using local->_oper_channel_type in the mesh code is
completely wrong as this value is the combination
of the various interface channel types and can be
a different value from the mesh interface in case
there are multiple virtual interfaces.

Use sdata->vif.bss_conf.channel_type instead as it
tracks the per-vif channel type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no need to use a single scratch buffer and
calculate offsets into it, just use two separate
buffers for the separate variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Advertise support for P2P Device in hwsim
to be able to test it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some devices like the current iwlwifi implementation
require that the P2P interface address match the P2P
Device address (only one P2P interface is supported.)
Add the HW flag IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF
that allows drivers to request that P2P Interfaces
added while a P2P Device is active get the same MAC
address by default.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In order to support using a different MAC address
for the P2P Device address we must first have a
P2P Device abstraction that can be assigned a MAC
address.

This abstraction will also be useful to support
offloading P2P operations to the device, e.g.
periodic listen for discoverability.

Currently, the driver is responsible for assigning
a MAC address to the P2P Device, but this could be
changed by allowing a MAC address to be given to
the NEW_INTERFACE command.

As it has no associated netdev, a P2P Device can
only be identified by its wdev identifier but the
previous patches allowed using the wdev identifier
in various APIs, e.g. remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no need to declare the function in the
header file since it's only used in a single
place, so make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>