- 16 Oct, 2008 40 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits) decnet: Fix compiler warning in dn_dev.c IPV6: Fix default gateway criteria wrt. HIGH/LOW preference radv option net/802/fc.c: Fix compilation warnings netns: correct mib stats in ip6_route_me_harder() netns: fix net_generic array leak rt2x00: fix regression introduced by "mac80211: free up 2 bytes in skb->cb" rtl8187: Add USB ID for Belkin F5D7050 with RTL8187B chip p54usb: Device ID updates mac80211: fixme for kernel-doc ath9k/mac80211: disallow fragmentation in ath9k, report to userspace libertas : Remove unused variable warning for "old_channel" from cmd.c mac80211: Fix scan RX processing oops orinoco: fix unsafe locking in spectrum_cs_suspend orinoco: fix unsafe locking in orinoco_cs_resume cfg80211: fix debugfs error handling mac80211: fix debugfs netdev rename iwlwifi: fix ct kill configuration for 5350 mac80211: fix HT information element parsing p54: Fix compilation problem on PPC mac80211: fix debugfs lockup ...
-
Linus Torvalds authored
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (51 commits) [ARM] 5308/1: Fix Viper ISA IRQ handling [ARM] 5307/1: pxa: fix CM-X2XX PCMCIA build error [ARM] 5306/1: pxa: fix build error on CM-X270 [ARM] 5302/1: ARM: OMAP: Revert omap3 WDT changes to avoid merge conflict [ARM] 5305/1: ARM: OMAP: Fix compile of McBSP by removing unnecessary check [ARM] 5301/1: ARM: OMAP: Add missing irq defines ARM: OMAP3: Add default kernel config for OMAP LDP ARM: OMAP3: Add basic board support for OMAP LDP ARM: OMAP3: Defconfig for the Gumstix Overo board (rev 3) ARM: OMAP3: Add support for the Gumstix Overo board (rev 3) ARM: OMAP3: Add Beagle defconfig ARM: OMAP3: Add minimal Beagle board support ARM: OMAP3: Add minimal omap3430 support ARM: OMAP2: Fix sparse, checkpatch warnings in OMAP2/3 IRQ code ARM: OMAP: Fixes to omap_mcbsp_request function ARM: OMAP: Add support for OMAP2430 in McBSP ARM: OMAP: Add support for McBSP devices 3 - 5 on 34xx ARM: OMAP: Allocate McBSP devices dynamically Fix sections for omap-mcbsp platform driver [ARM] S3C24XX: Additional include moves ...
-
Julia Lawall authored
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) / (d)) but is perhaps more readable. An extract of the semantic patch that makes this change is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @haskernel@ @@ #include <linux/kernel.h> @depends on haskernel@ expression n,d; @@ ( - (n + d - 1) / d + DIV_ROUND_UP(n,d) | - (n + (d - 1)) / d + DIV_ROUND_UP(n,d) ) @depends on haskernel@ expression n,d; @@ - DIV_ROUND_UP((n),d) + DIV_ROUND_UP(n,d) @depends on haskernel@ expression n,d; @@ - DIV_ROUND_UP(n,(d)) + DIV_ROUND_UP(n,d) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Acked-by:
Jeremy Fitzhardinge <jeremy@goop.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Adrian Bunk authored
Make the needlessly global kretprobe_table_lock() static. Signed-off-by:
Adrian Bunk <bunk@kernel.org> Acked-by:
Ananth N Mavinakayanahalli <ananth@in.ibm.com> Signed-off-by:
-
Adrian Bunk authored
Make the needlessly global hp_wmi_notify() static. Signed-off-by:
-
Adrian Bunk authored
Signed-off-by:
-
Magnus Damm authored
Add resource_type() and IORESOURCE_TYPE_BITS. They make it easier to add more resource types without having to rewrite tons of code. Signed-off-by:
Magnus Damm <damm@igel.co.jp> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by:
-
Bjorn Helgaas authored
No functional change. Just return NULL for kzalloc failure immediately, rather than wrapping the whole function body in the body of an "if". Signed-off-by:
Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by:
-
Jack Steiner authored
A few minor updates for the GRU driver. - documentation changes found in code reviews - changes to #ifdefs to make them recognized by "unifdef" (used in simulator testing) - change GRU context load/unload to prefetch data [akpm@linux-foundation.org: fix typo in comment] Signed-off-by:
Jack Steiner <steiner@sgi.com> Signed-off-by:
-
Thomas Petazzoni authored
This patchs adds the CONFIG_AIO option which allows to remove support for asynchronous I/O operations, that are not necessarly used by applications, particularly on embedded devices. As this is a size-reduction option, it depends on CONFIG_EMBEDDED. It allows to save ~7 kilobytes of kernel code/data: text data bss dec hex filename 1115067 119180 217088 1451335 162547 vmlinux 1108025 119048 217088 1444161 160941 vmlinux.new -7042 -132 0 -7174 -1C06 +/- This patch has been originally written by Matt Mackall <mpm@selenic.com>, and is part of the Linux Tiny project. [randy.dunlap@oracle.com: build fix] Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Zach Brown <zach.brown@oracle.com> Signed-off-by:
Matt Mackall <mpm@selenic.com> Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by:
-
Bernhard Weirich authored
[akpm@linux-foundation.org: minor fixlets and cleanups] Signed-off-by:
Bernhard Weirich <bernhard.weirich@riedel.net> Signed-off-by:
Evgeniy Polyakov <johnpol@2ka.mipt.ru> Cc: Ben Gardner <bgardner@wabtec.com> Signed-off-by:
-
David Fries authored
Optimize the ds_set_pullup function. For a strong pullup to be sent the ds2490 has to have both the strong pullup mode enabled, and the specific write operation has to have the SPU bit enabled. Previously the write always had the SPU bit enabled and both the duration and model was set when a strong pullup was requested. Now the strong pullup mode is enabled at initialization time, the delay is updated only when the value changes, and the write SPU bit is set only when a strong pullup is required. This removes two or three bus transactions per strong pullup request. Signed-off-by:
David Fries <david@fries.net> Signed-off-by:
-
David Fries authored
Provide some additional details about the status of the driver and the ds2490 hardware. Signed-off-by:
-
David Fries authored
Drop the extra ds_wait_status() in ds_write_block(). Signed-off-by:
-
David Fries authored
This replaces some magic numbers with marcos and corrects one marco. Signed-off-by:
-
David Fries authored
Reset the device in init as it can be in a bad state. This is necessary because a block write will wait for data to be placed in the output buffer and block any later commands which will keep accumulating and the device will not be idle. Another case is removing the ds2490 module while a bus search is in progress, somehow a few commands get through, but the input transfers fail leaving data in the input buffer. This will cause the next read to fail see the note in ds_recv_data. Signed-off-by:
-
David Fries authored
ds_reset no longer calls ds_wait_status, the result wasn't used and it would only delay the following data operations. Signed-off-by:
-
David Fries authored
- add result register #defines - rename ds_dump_status to ds_print_msg - rename ds_recv_status to ds_dump_status - ds_dump_status prints the requested status and no longer reads the status, this is because the second status read can return different data for example the result register - the result register will be printed, though limited to detecting a new device, detecting other values such as a short would require additional reporting methods - ST_EPOF was moved to ds_wait_status to clear the error condition sooner Signed-off-by:
-
David Fries authored
Simplify and fix ds_touch_bit. If a device is attached in the middle of a bus search the status register will return more than the default 16 bytes. The additional bytes indicate that it has detected a new device. The way ds_wait_status is coded, if it doesn't read 16 status bytes it returns an error value. ds_touch_bit then will detect that error and return an error. In that case it doesn't read the input buffer and returns uninitialized data. It doesn't stop there. The next transaction will not expect the extra byte in the input buffer and the short read will cause an error and clear out both the old byte and new data in the input buffer. Just ignore the value of ds_wait_status. It is still required to wait until ds2490 is again idle and there is data to read when ds_recv_data is called. This also removes the while loop. None of the other commands wait and verify that the issued command is in the status register. Signed-off-by:
-
David Fries authored
Don't export read and write bit operations, they didn't work, they weren't used, and they can't be made to work. The one wire low level bit operations expect to set high or low levels, the ds2490 hardware only supports complete read or write time slots, better to just comment them out. Signed-off-by:
-
David Fries authored
ds_write_bit doesn't read the input buffer, so add COMM_ICP and a comment that it will no longer generate a read back data byte. If there is an extra data byte later on then it will cause an error and discard what data was there. Corrected operator ordering for ds_send_control. Signed-off-by:
-
David Fries authored
Add strong pullup support for ds2490 driver, also drop mdelay(750), which busy waits, usage in favour of msleep for long delays. Now with msleep only being called when the strong pullup is active, one wire bus operations are only taking minimal system overhead. The new set_pullup will only enable the strong pullup when requested, which is expected to be the only write operation that will benefit from a strong pullup. Signed-off-by:
-
David Fries authored
Corrected print message, it was writing not reading, this also prints the endpoint used for the write instead of hardcoding it. Failed to write 1-wire data to ep0x%x: err=%d. Signed-off-by:
-
David Fries authored
Like the previous w1_io.c reset coments and msleep patch, I don't have the hardware to verify the change, but I think it is safe. It also helps to see a comment like this in the code. "We'll wait a bit longer just to be sure." If they are going to calculate delaying 324.9us, but actually delay 500us, why not just give up the CPU and sleep? This is designed for a battery powered ARM system, avoiding busywaiting has to be good for battery life. I sent a request for testers March 7, 2008 to the Linux kernel mailing list and two developers who have patches for ds1wm.c, but I didn't get any respons. Signed-off-by:
-
David Fries authored
w1_reset_bus, added some comments about the timing and switched to msleep for the later delay. I don't have the hardware to test the sleep after reset change. The one wire doesn't have a timing requirement between commands so it is fine. I do have the USB hardware and it would be in big trouble with 10ms interrupt transfers to find that the reset completed. Signed-off-by:
-
David Fries authored
s/printk/dev_dbg/ Signed-off-by:
-
David Fries authored
Follow the example of other devices (like the joystick device). Pick the first available id for each detected device. Currently for USB devices, suspending and resuming would cause the number to increment. Signed-off-by:
-
David Fries authored
sl->master->mutex and dev->mutex refer to the same mutex variable, but be consistent and use the same set of pointers for the lock and unlock calls. It is less confusing (and one less pointer dereference this way). Signed-off-by:
-
David Fries authored
Removed the w1_family structure member variable need_exit. It was only being set and never used. Even if it were to be used it is a polling type operation. Signed-off-by:
-
David Fries authored
Fixed data reading bug by replacing binary attribute with device one. Switching the sysfs read from bin_attribute to device_attribute. The data is far under PAGE_SIZE so the binary interface isn't required. As the device_attribute interface will make one call to w1_therm_read per file open and buffer, the result is, the following problems go away. buffer overflow: Execute a short read on w1_slave and w1_therm_read_bin would still return the full string size worth of data clobbering the user space buffer when it returned. Switching to device_attribute avoids the buffer overflow problems. With the snprintf formatted output dealing with short reads without doing a conversion per read would have been difficult. bad behavior: `cat w1_slave` would cause two temperature conversions to take place. Previously the code assumed W1_SLAVE_DATA_SIZE would be returned with each read. It would not return 0 unless the offset was less than W1_SLAVE_DATA_SIZE. The result was the first read did a temperature conversion, filled the buffer and returned, the offset in the second read would be less than W1_SLAVE_DATA_SIZE and also fill the buffer and return, the third read would finnally have a big enough offset to return 0 and cause cat to stop. Now w1_therm_read will be called at most once per open. Signed-off-by:
-
David Fries authored
Fix bug reading the id sysfs file. If less than the full 8 bytes were read, the next read would start at the first byte instead of continuing. It needed the offset added to memcpy, or the better solution was to replace it with the device attribute instead of bin attribute. Signed-off-by:
-
David Fries authored
Document w1_master_add, w1_master_remove, search_count, and pullup. Signed-off-by:
-
David Fries authored
Added a new module parameter search_count which allows overriding the default search count. -1 continual, 0 disabled, N that many times. Signed-off-by:
-
David Fries authored
Simplified the logic in w1_slave_found by using the new w1_attach_slave_device function to find a slave and mark it as active or add the device if the crc checks. Signed-off-by:
-
David Fries authored
sysfs entries were added to manually add and remove slave devices. This is useful if the automatic bus searching is disabled, and the device ids are already known. [akpm@linux-foundation.org: fix printk types] Signed-off-by:
-
David Fries authored
Added strong pullup to thermal sensor driver and general documentation on the sensor. Signed-off-by:
-
David Fries authored
Add a strong pullup option to the w1 system. This supplies extra power for parasite powered devices. There is a w1_master_pullup sysfs entry and enable_pullup module parameter to enable or disable the strong pullup. The one wire bus requires at a minimum one wire and ground. The common wire is used for sending and receiving data as well as supplying power to devices that are parasite powered of which temperature sensors can be one example. The bus must be idle and left high while a temperature conversion is in progress, in addition the normal pullup resister on larger networks or even higher temperatures might not supply enough power. The pullup resister can't provide too much pullup current, because devices need to pull the bus down to write a value. This enables the strong pullup for supported hardware, which can supply more current when requested. Unsupported hardware will just delay with the bus high. The hardware USB 2490 one wire bus master has a bit on some commands which will enable the strong pullup as soon as the command finishes executing. To use strong pullup, call the new w1_next_pullup function to register the duration. The next write command will call set_pullup before sending the data, and reset the duration to zero once it returns. Switched from simple_strtol to strict_strtol. Signed-off-by:
-
David Fries authored
The w1_process thread's sleeping and termination has been modified. msleep_interruptible was replaced by schedule_timeout and schedule to allow for kthread_stop and wake_up_process to interrupt the sleep and the unbounded sleeping when a bus search is disabled. The W1_MASTER_NEED_EXIT and flags variable were removed as they were redundant with kthread_should_stop and kthread_stop. If w1_process is sleeping, requesting a search will immediately wake it up rather than waiting for the end of msleep_interruptible previously. Signed-off-by:
-
David Fries authored
Move the creation of the w1_process thread to after the device has been initialized. This way w1_process doesn't have to check to see if it has been initialized and the bus search can proceed without sleeping. That also eliminates two checks in the w1_process loop. The sleep now happens at the end of the loop not the beginning. Also added a comment for why the atomic_set was 2. Signed-off-by:
-
David Fries authored
Early abort if the master driver or the hardware goes away in the middle of a bus search operation. The alternative is to spam the print buffer up to 64*64 times with read errors in the case of USB. Signed-off-by:
-
