For hso serial devices, two cancel_work_sync were missing in the
disconnect method.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

The serial_table is used to map the minor number of the usb serial device
to its associated context. The table is updated in the probe method and
in hso_serial_ref_free() which is called either from the tty cleanup
method or from the usb disconnect method.
This patch ensures that the serial_table is updated in the disconnect
method and no more from the cleanup method to avoid the following
potential race condition.

 - hso_disconnect() is called for usb interface "x". Because the serial
   port was open and because the cleanup method of the tty_port hasn't
   been called yet, hso_serial_ref_free() is not run.
 - hso_probe() is called and fails for a new hso serial usb interface
   "y". The function hso_free_interface() is called and iterates
   over the element of serial_table to find the device associated to
   the usb interface context.
   If the usb interface context of usb interface "y" has been created
   at the same place as for usb interface "x", then the cleanup
   functions are called for usb interfaces "x" and "y" and
   hso_serial_ref_free() is called for both interfaces.
 - release_tty() is called for serial port linked to usb interface "x"
   and possibly crash because the tty_port structure contained in the
   hso_device structure has been freed.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function hso_serial_common_free() is called either by the cleanup
method of the tty or by the usb disconnect method.
In the former case, the usb_disconnect() has been already called
and the sysfs group associated to the device has been removed.
By calling tty_unregister directly from the usb_disconnect() method,
we avoid a warning due to the removal of the sysfs group of the usb
device.

Example of warning:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 778 at fs/sysfs/group.c:225 sysfs_remove_group+0x50/0x94()
sysfs group c0645a88 not found for kobject 'ttyHS5'
Modules linked in:
CPU: 0 PID: 778 Comm: kworker/0:3 Tainted: G        W      3.18.0+ #105
Workqueue: events release_one_tty
[<c000dfe4>] (unwind_backtrace) from [<c000c014>] (show_stack+0x14/0x1c)
[<c000c014>] (show_stack) from [<c0016bac>] (warn_slowpath_common+0x5c/0x7c)
[<c0016bac>] (warn_slowpath_common) from [<c0016c60>] (warn_slowpath_fmt+0x30/0x40)
[<c0016c60>] (warn_slowpath_fmt) from [<c00ddd14>] (sysfs_remove_group+0x50/0x94)
[<c00ddd14>] (sysfs_remove_group) from [<c0221e44>] (device_del+0x30/0x190)
[<c0221e44>] (device_del) from [<c0221fb0>] (device_unregister+0xc/0x18)
[<c0221fb0>] (device_unregister) from [<c0221fec>] (device_destroy+0x30/0x3c)
[<c0221fec>] (device_destroy) from [<c01fe1dc>] (tty_unregister_device+0x2c/0x5c)
[<c01fe1dc>] (tty_unregister_device) from [<c029a428>] (hso_serial_common_free+0x2c/0x88)
[<c029a428>] (hso_serial_common_free) from [<c029a4c0>] (hso_serial_ref_free+0x3c/0xb8)
[<c029a4c0>] (hso_serial_ref_free) from [<c01ff430>] (release_one_tty+0x30/0x84)
[<c01ff430>] (release_one_tty) from [<c00271d4>] (process_one_work+0x21c/0x3c8)
[<c00271d4>] (process_one_work) from [<c0027758>] (worker_thread+0x3d8/0x560)
[<c0027758>] (worker_thread) from [<c002be4c>] (kthread+0xc0/0xcc)
[<c002be4c>] (kthread) from [<c0009630>] (ret_from_fork+0x14/0x24)
---[ end trace cb88537fdc8fa208 ]---
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need for a dedicated reset work in the hso driver since
there is already a reset work foreseen in usb_interface that does
the same.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

In other functions of the driver, variables of type "struct hso_serial"
are denoted by "serial" and variables of type "struct hso_device" are
denoted by "hso_dev". This patch makes the hso_free_interface()
consistent with these notations.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simply remove the useless extra tab.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the rfkill interface was created, a buffer containing the name
of the rfkill node was allocated. This buffer was never freed when the
device disappears.

To fix the problem, we put the name given to rfkill_alloc() in
the hso_net structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the disconnect path, tx_buffer should freed like tx_data to avoid
a memory leak when the device disconnects.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the device disappear, the function hso_disconnect() is called to
perform cleanup. In the cleanup function, hso_free_interface() calls
tty_port_tty_hangup() in view of scheduling a work to hang up the tty if
needed. If the port was not open then hso_serial_ref_free() is called
directly to cleanup everything. Otherwise, hso_serial_ref_free() is called
when the last fd associated to the port is closed.

For each open port, tty_release() will call the close method,
hso_serial_close(), which drops the last kref and call
hso_serial_ref_free() which unregisters, destroys the tty port
and finally frees the structure in which the tty_port structure
is included. Later, in tty_release(), more precisely when release_tty()
is called, the tty_port previously freed is accessed to cancel
the tty buf workqueue and it leads to a crash.

In view of avoiding this crash, we add a cleanup method that is called
at the end of the hangup process and we drop the last kref in this
function when all the ports have been closed, when tty_port is no
more needed and when it is safe to free the structure containing the
tty_port structure.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

No timer related function is used in this driver.
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

Get rid of nr_cpu_ids and use modern percpu allocation.

Note that the sockets themselves are not yet allocated
using NUMA affinity.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NetCP on Keystone has cpsw ale function similar to other TI SoCs
and this driver is re-used. To allow both ti cpsw and keystone netcp
to re-use the driver, convert the cpsw ale to a module and configure
it through Kconfig option CONFIG_TI_CPSW_ALE. Currently it is statically
linked to both TI CPSW and NetCP and this causes issues when the above
drivers are built as dynamic modules. This patch addresses this issue

While at it, fix the Makefile and code to build both netcp_core and
netcp_ethss as dynamic modules. This is needed to support arm allmodconfig.
This also requires exporting of API calls provided by netcp_core so that
both the above can be dynamic modules.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current behavior only passes RTTs from sequentially acked data to CC.

If sender gets a combined ACK for segment 1 and SACK for segment 3, then the
computed RTT for CC is the time between sending segment 1 and receiving SACK
for segment 3.

Pass the minimum computed RTT from any acked data to CC, i.e. time between
sending segment 3 and receiving SACK for segment 3.
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is only an API consolidation and should make things more readable
it replaces  var * HZ / 1000  constructs by  msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow the selftest on the resizable hash table to be built modular, just
like all other tests that do not depend on DEBUG_KERNEL.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

They are all either written once or extremly rarely (e.g. from init
code), so we can move them to the .data..read_mostly section.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Lindgren says:

====================
Changes to cpsw and davinci_emac for getting MAC address

Here are a few patches to add common code for cpsw and davinci_emac for
getting the MAC address. Looks like we can also now add code to get the
MAC address on 3517 but in a slightly different way.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like on 3517 davinci_emac MAC address registers have a
different layout compared to dm816x and am33xx.

Let's add a function to get the 3517 MAC address.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At least on dm81xx, we can get the davinci_emac MAC address the same
way as on am33xx cpsw.

Let's also use ether_addr_copy() for davinci_emac while at it.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like davinci_emac and cpsw can share some code although the
device registers have a different layout.

At least the code for getting the MAC address using syscon can
be shared by passing the register offset. Let's start with that
and set up a minimal shared cpsw-shared.c.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-3.20-20150128' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2015-28-01

this is a pull request of 12 patches for net-next/master.

There are 3 patches by Ahmed S. Darwish, which update the kvaser_usb
driver and add support for the USBcan-II based adapters. Stéphane
Grosjean contributes 7 patches for the peak_usb driver, which add
support for the CANFD USB adapters. I contribute 2 patches which clean
up the peak_usb driver structure a bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit cd1e6504 ("of/device: Don't register disabled
devices"), the disabled device will not be registered at all. So we
don't need to do the check again in the platform device driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When many pf_packet listeners are created on a lot of interfaces the
current implementation using global packet type lists scales poorly.
This patch adds per net_device packet type lists to fix this problem.

The patch was originally written by Eric Biederman for linux-2.6.29.
Tested on linux-3.16.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When IFLA_LINK_NETNSID is used, the netdevice should be built in this link netns
and moved at the end to another netns (pointed by the socket netns or
IFLA_NET_NS_[PID|FD]).

Existing user of the newlink handler will use the netns argument (src_net) to
find a link netdevice or to check some other information into the link netns.
For example, to find a netdevice, two information are required: an ifindex
(usually from IFLA_LINK) and a netns (this link netns).

Note: when using IFLA_LINK_NETNSID and IFLA_NET_NS_[PID|FD], a user may create a
netdevice that stands in netnsX and with its link part in netnsY, by sending a
rtnl message from netnsZ.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TIME_WAIT sockets are not owning any skb.

ip_send_unicast_reply() and tcp_v6_send_response() both use
regular sockets.

We can safely remove a test in sch_fq and save one cache line miss,
as sk_state is far away from sk_pacing_rate.

Tested at Google for about one year.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NET_ACT_CONNMARK fails to build if NF_CONNTRACK_MARK is disabled,
and d7924450 ("act_connmark: Add missing dependency on
NF_CONNTRACK_MARK") fixed that case, but missed the cased where
NF_CONNTRACK is a loadable module.

This adds the second dependency to ensure that NET_ACT_CONNMARK
can only be built-in if NF_CONNTRACK is also part of the kernel
rather than a loadable module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sock_iocb structure is allocate on stack for each read/write-like
operation on sockets, and contains various fields of which only the
embedded msghdr and sometimes a pointer to the scm_cookie is ever used.
Get rid of the sock_iocb and put a msghdr directly on the stack and pass
the scm_cookie explicitly to netlink_mmap_sendmsg.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The if block was supposed to have curly braces.  In the current code we
complain about dropped rx packets when we shouldn't.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, it isn't possible to request checksums on the outer UDP
header of tunnels - the TUNNEL_CSUM flag is ignored. This adds
support for requesting that UDP checksums be computed on transmit
and properly reported if they are present on receive.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NFC: 3.20 first pull request

This is the first NFC pull request for 3.20.

With this one we have:

- Secure element support for the ST Micro st21nfca driver. This depends
  on a few HCI internal changes in order for example to support more
  than one secure element per controller.

- ACPI support for NXP's pn544 HCI driver. This controller is found on
  many x86 SoCs and is typically enumerated on the ACPI bus there.

- A few st21nfca and st21nfcb fixes.
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the following new PEAK-System technik CANFD USB adapters:

PCAN-USB FD             single CANFD channel USB adapter
PCAN-USB Pro FD         dual CANFD channels USB adapter
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add a common function that pushes the skb in the network queue with adding
timestamps information, converted from time values read from the
PEAK USB adapters.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add support for the following new PEAK-System technik CANFD USB adapters:

PCAN-USB FD             single CANFD channel USB adapter
PCAN-USB Pro FD         dual CANFD channels USB adapter

The communication protocol has been developed using some mechanisms that
did exist in the PCAN-USB Pro, thus, this patch also changes some
previously static functions and data into global ones.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Upgrade PEAK-System USB adapters core to the new data structures (names) and
callbacks added for the support of the CANFD extension. This specific patch
includes changes that deal with the new struct canfd_frame.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Upgrade PEAK-System USB adapters core to the new data structures (names) and
callbacks added for the support of the CANFD extension. This specific patch
does the mandatory changes to support new data bittiming specs.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add the definition of a new callback that enable any PEAK-System CAN USB
adapter to grant read access to its Bus Error Counters value. This ability is
not supported by all the PEAK-System adapters, thus, for those, the callback
pointer will be initiaized to NULL, which is correct regarding the linux-can
device driver specs.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Export the ctrlmode_supported value from the core file to each adapter specific
file. This has been mandatory for supporting the new CANFD extension.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

A "struct peak_usb_adapter" describes a certain USB adapter, as this doesn't
change during runtime, this patch marks all USB adapter definitions as const.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch converts the list "static struct peak_usb_adapter
*peak_usb_adapters_list[]" to be used with ARRAY_SIZE not with a NULL
termination, as the size is known during compile time.
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

CAN to USB interfaces sold by the Swedish manufacturer Kvaser are
divided into two major families: 'Leaf', and 'USBcanII'.  From an
Operating System perspective, the firmware of both families behave
in a not too drastically different fashion.

This patch adds support for the USBcanII family of devices to the
current Kvaser Leaf-only driver.

CAN frames sending, receiving, and error handling paths has been
tested using the dual-channel "Kvaser USBcan II HS/LS" dongle. It
should also work nicely with other products in the same category.

List of new devices supported by this driver update:

         - Kvaser USBcan II HS/HS
         - Kvaser USBcan II HS/LS
         - Kvaser USBcan Rugged ("USBcan Rev B")
         - Kvaser Memorator HS/HS
         - Kvaser Memorator HS/LS
         - Scania VCI2 (if you have the Kvaser logo on top)
Signed-off-by: Ahmed S. Darwish <ahmed.darwish@valeo.com>
Acked-by: Andri Yngvason <andri.yngvason@marel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>