Included change:
- Check if the skb has been correctly prepared before going on

Do not clear Broadcast/Multicast/Unicast Wake Flag or LanWake in
Config5. This is necessary to preserve WOL state when the driver is
loaded. Although the r8168 vendor driver does not write Config5 (it has
been commented out), Hayes Wang from Realtek said that masking bits like
this is more sensible.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If via_ircc_open() fails, data structures of the driver left uninitialized,
but probe (via_init_one()) returns zero. That can lead to null pointer dereference
in via_remove_one(), since it does not check drvdata for NULL.

The patch implements proper error code propagation.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the user turns off VNET_HDR support on the
macvtap device, there is no way to provide any
offload information to the user.  So, it's safer
to ignore offload setting then depend on the user
setting them correctly.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the user turns off IFF_VNET_HDR flag, attempts to change
offload features via TUNSETOFFLOAD do not work.  This could cause
GSO packets to be delivered to the user when the user is
not prepared to handle them.

To solve, allow processing of TUNSETOFFLOAD when IFF_VNET_HDR is
disabled.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In macvtap, tap_features specific the features of that the user
has specified via ioctl().  If we treat macvtap as a macvlan+tap
then we could all the tap a pseudo-device and give it other features
like SG and GSO.  Then we can stop using the features of lower
device (macvlan) when forwarding the traffic the tap.

This solves the issue of possible checksum offload mismatch between
tap feature and macvlan features.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the repair mode is turned off, the write queue seqs are
updated so that the whole queue is considered to be 'already sent.

The "when" field must be set for such skb. It's used in tcp_rearm_rto
for example. If the "when" field isn't set, the retransmit timeout can
be calculated incorrectly and a tcp connected can stop for two minutes
(TCP_RTO_MAX).
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are possible HW configurations in which PFs will have SR-IOV capability
but will have Max VFs set to 0 - this happens when there are Multi-Function
devices where the VFs are allocated to only some of the PFs.

DMAE is configured to support VFs only if the configuring PF has supported VFs.
In case the first PF to be loaded will be one without supported VFs, it will
not configure DMAE to the VF-supporting mode. When VFs of other PFs will be
loaded later on, they will not be able to communicate with their PF.

This changes the requirement for configuring DMAE for VF-supporting mode;
If the device has SR-IOV capabilities there must be some PF that has
max supported VFs > 0, thus it will configure the DMAE for supporting VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since SR-IOV can be activated dynamically and iproute2 can be called
asynchronously, the various callbacks need a robust sanity check before
attempting to access the SR-IOV database and members since there are numerous
states in which it can find the driver (e.g., PF is down, sriov was not enabled
yet, VF is down, etc.).

In many of the states the callback result will be null pointer dereference.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During probe, VFs might erroneously try to access the shared memory (which
only PFs are capabale of accessing), causing benign attentions to appear.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When publishing information via getfeatcfg(), bnx2x driver didn't consider
remote errors (e.g., switch that doesn't support DCBX) when setting the
error flags.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After notification that DCBX configuration has ended arrived to the driver,
the driver configured the FW/HW in sleepless context.
As a result, it was possible to reach a race (mostly with CNIC registration)
in which the configuration will return a timeout, failing to set the DCBX
results correctly.

This patch moves the configuration following the DCBX end into the slowpath
RTNL task (i.e., sleepless context protected by the RTNL lock), allowing the
configuration to cope with such races.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 3deb8167 "bnx2x: Add a periodic task for link PHY events"
link state changes can be detected not only via the attention flow but also
from the periodic task.
If the link state will change in such a manner (i.e., via the periodic task),
dropless flow-control will not be configured.

This patch remedies the issue, adding the missing configuration to all required
flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is not allowed for an ipv6 packet to contain multiple fragmentation
headers. So discard packets which were already reassembled by
fragmentation logic and send back a parameter problem icmp.

The updates for RFC 6980 will come in later, I have to do a bit more
research here.

Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because of the max_addresses check attackers were able to disable privacy
extensions on an interface by creating enough autoconfigured addresses:

<http://seclists.org/oss-sec/2012/q4/292>

But the check is not actually needed: max_addresses protects the
kernel to install too many ipv6 addresses on an interface and guards
addrconf_prefix_rcv to install further addresses as soon as this limit
is reached. We only generate temporary addresses in direct response of
a new address showing up. As soon as we filled up the maximum number of
addresses of an interface, we stop installing more addresses and thus
also stop generating more temp addresses.

Even if the attacker tries to generate a lot of temporary addresses
by announcing a prefix and removing it again (lifetime == 0) we won't
install more temp addresses, because the temporary addresses do count
to the maximum number of addresses, thus we would stop installing new
autoconfigured addresses when the limit is reached.

This patch fixes CVE-2013-0343 (but other layer-2 attacks are still
possible).

Thanks to Ding Tianhong to bring this topic up again.

Cc: Ding Tianhong <dingtianhong@huawei.com>
Cc: George Kargiotakis <kargig@void.gr>
Cc: P J P <ppandit@redhat.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the previous commit, Richard Genoud fixed proc_root_readdir(), which
had lost the check for whether all of the non-process /proc entries had
been returned or not.

But that in turn exposed _another_ bug, namely that the original readdir
conversion patch had yet another problem: it had lost the return value
of proc_readdir_de(), so now checking whether it had completed
successfully or not didn't actually work right anyway.

This reinstates the non-zero return for the "end of base entries" that
had also gotten lost in commit f0c3b509 ("[readdir] convert
procfs").  So now you get all the base entries *and* you get all the
process entries, regardless of getdents buffer size.

(Side note: the Linux "getdents" manual page actually has a nice example
application for testing getdents, which can be easily modified to use
different buffers.  Who knew? Man-pages can be useful)
Reported-by: Emmanuel Benisty <benisty.e@gmail.com>
Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit f0c3b509 ("[readdir] convert procfs") introduced a bug on the
listing of the proc file-system.  The return value of proc_readdir()
isn't tested anymore in the proc_root_readdir function.

This lead to an "interesting" behaviour when we are using the getdents()
system call with a buffer too small: instead of failing, it returns the
first entries of /proc (enough to fill the given buffer), plus the PID
directories.

This is not triggered on glibc (as getdents is called with a 32KB
buffer), but on uclibc, the buffer size is only 1KB, thus some proc
entries are missing.

See https://lkml.org/lkml/2013/8/12/288 for more background.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull gfs2 fixes from Steven Whitehouse:
 "Out of these five patches, the one for ensuring that the number of
  revokes is not exceeded, and the one for checking the glock is not
  already held in gfs2_getxattr are the two most important.  The latter
  can be triggered by selinux.

  The other three patches are very small and fix mostly fairly trivial
  issues"

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
  GFS2: Check for glock already held in gfs2_getxattr
  GFS2: alloc_workqueue() doesn't return an ERR_PTR
  GFS2: don't overrun reserved revokes
  GFS2: WQ_NON_REENTRANT is meaningless and going away
  GFS2: Fix typo in gfs2_create_inode()

Pull x86 fixes from Ingo Molnar:
 "Two AMD microcode loader fixes and an OLPC firmware support fix"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, microcode, AMD: Fix early microcode loading
  x86, microcode, AMD: Make cpu_has_amd_erratum() use the correct struct cpuinfo_x86
  x86: Don't clear olpc_ofw_header when sentinel is detected

Pull timer fixes from Ingo Molnar:
 "Three small fixlets"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  nohz: fix compile warning in tick_nohz_init()
  nohz: Do not warn about unstable tsc unless user uses nohz_full
  sched_clock: Fix integer overflow

Pull drm fixes from Dave Airlie:
 "Bit late with these, was under the weather for a a few days, nothing
  too crazy:

  Some radeon regression fixes, one intel regression fix, and one fix to
  avoid a warn with i915 when used with dma-buf"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: unpin backing storage in dmabuf_unmap
  drm/radeon: fix WREG32_OR macro setting bits in a register
  drm/radeon/r7xx: fix copy paste typo in golden register setup
  drm/i915: Don't deref pipe->cpu_transcoder in the hangcheck code
  drm/radeon: fix UVD message buffer validation

Fix new kernel-doc warnings in kernel/wait.c:

  Warning(kernel/wait.c:374): No description found for parameter 'p'
  Warning(kernel/wait.c:374): Excess function parameter 'word' description in 'wake_up_atomic_t'
  Warning(kernel/wait.c:374): Excess function parameter 'bit' description in 'wake_up_atomic_t'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since the introduction of atomic_open, gfs2_getxattr can be
called with the glock already held, so we need to allow for
this.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Reported-by: David Teigland <teigland@redhat.com>
Tested-by: David Teigland <teigland@redhat.com>

alloc_workqueue() returns a NULL on error, it doesn't return an ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

When run during fsync, a gfs2_log_flush could happen between the
time when gfs2_ail_flush checked the number of blocks to revoke,
and when it actually started the transaction to do those revokes.
This occassionally caused it to need more revokes than it reserved,
causing gfs2 to crash.

Instead of just reserving enough revokes to handle the blocks that
currently need them, this patch makes gfs2_ail_flush reserve the
maximum number of revokes it can, without increasing the total number
of reserved log blocks. This patch also passes the number of reserved
revokes to __gfs2_ail_flush() so that it doesn't go over its limit
and cause a crash like we're seeing. Non-fsync calls to __gfs2_ail_flush
will still cause a BUG() necessary revokes are skipped.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

dbf2576e ("workqueue: make all workqueues non-reentrant") made
WQ_NON_REENTRANT no-op and the flag is going away.  Remove its usages.

This patch doesn't introduce any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: cluster-devel@redhat.com

PTR_RET should be PTR_ERR
Reported-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>

* tag 'drm-intel-fixes-2013-08-15' of git://people.freedesktop.org/~danvet/drm-intel: (153 commits)
  drm/i915: Don't deref pipe->cpu_transcoder in the hangcheck code

This fixes a WARN in i915_gem_free_object when the
obj->pages_pin_count isn't 0.

v2: Add locking to unmap, noticed by Chris Wilson. Note that even
though we call unmap with our own dev->struct_mutex held that won't
result in an immediate deadlock since we never go through the dma_buf
interfaces for our own, reimported buffers. But it's still easy to
blow up and anger lockdep, but that's already the case with our ->map
implementation. Fixing this for real will involve per dma-buf ww mutex
locking by the callers. And lots of fun. So go with the duct-tape
approach for now.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Tested-by: Armin K. <krejzi@email.com> (v1)
Tested-by: Dave Airlie <airlied@redhat.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>

Just two small fixes for radeon.  One fixes an array overrun
that can cause garbage to get written to registers on some r7xx boards,
the other is a small UVD fix.
Also one audio regresion

* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix WREG32_OR macro setting bits in a register
  drm/radeon/r7xx: fix copy paste typo in golden register setup
  drm/radeon: fix UVD message buffer validation

Pull cgroup fix from Tejun Heo:
 "This contains one patch to fix the return value of cpuset's cgroups
  interface function, which used to always return -ENODEV for the writes
  on the 'memory_pressure_enabled' file"

* 'for-3.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cpuset: fix the return value of cpuset_write_u64()

batadv_unicast(_4addr)_prepare_skb  might reallocate the skb's data.
And if it tries to do so then this can potentially fail.

We shouldn't continue working on this skb in such a case.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>

Pull jbd2 bug fixes from Ted Ts'o:
 "Two jbd2 bug fixes, one of which is a regression fix"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  jbd2: Fix oops in jbd2_journal_file_inode()
  jbd2: Fix use after free after error in jbd2_journal_dirty_metadata()

Fix this build error:

  In file included from fs/exec.c:61:0:
  arch/s390/include/asm/tlb.h:35:23: error: expected identifier or '(' before 'unsigned'
  arch/s390/include/asm/tlb.h:36:1: warning: no semicolon at end of struct or union [enabled by default]
  arch/s390/include/asm/tlb.h: In function 'tlb_gather_mmu':
  arch/s390/include/asm/tlb.h:57:5: error: 'struct mmu_gather' has no member named 'end'

Broken due to commit 2b047252 ("Fix TLB gather virtual address range
invalidation corner cases").

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ Oh well. We had build testing for ppc amd um, but no s390  - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I have taken a different job.  I am removing myself as maintainer of
GRU.  Dimitri will continue to maintain the SGI GRU driver, changing the
XP/XPC/XPNET maintainer to Cliff Whickman, but leaving behind my
personal email address to answer any questions about the design or
operation of the XP family of drivers.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 0713ed0c added
jbd2_journal_file_inode() call into ext4_block_zero_page_range().
However that function gets called from truncate path and thus inode
needn't have jinode attached - that happens in ext4_file_open() but
the file needn't be ever open since mount. Calling
jbd2_journal_file_inode() without jinode attached results in the oops.

We fix the problem by attaching jinode to inode also in ext4_truncate()
and ext4_punch_hole() when we are going to zero out partial blocks.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

Pull ARM fixes from Russell King:
 "The usual collection of random fixes.  Also some further fixes to the
  last set of security fixes, and some more from Will (which you may
  already have in a slightly different form)"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7807/1: kexec: validate CPU hotplug support
  ARM: 7812/1: rwlocks: retry trylock operation if strex fails on free lock
  ARM: 7811/1: locks: use early clobber in arch_spin_trylock
  ARM: 7810/1: perf: Fix array out of bounds access in armpmu_map_hw_event()
  ARM: 7809/1: perf: fix event validation for software group leaders
  ARM: Fix FIQ code on VIVT CPUs
  ARM: Fix !kuser helpers case
  ARM: Fix the world famous typo with is_gate_vma()

Pull m68k fixes from Geert Uytterhoeven:
 "These are two critical fixes, needed by distro kernels, and thus also
  destined for stable:

   - The do_div() commit fixes a crash in mounting btrfs volumes, which
     was a regression from 3.2,

   - The ARAnyM fix allows to have NatFeat drivers as loadable modules,
     which is needed for initrds"

* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Truncate base in do_div()
  m68k/atari: ARAnyM - Fix NatFeat module support

Pull clock controller fixes from Michael Turquette:
 "Two small fixes for the Zynq clock controller introduced in 3.11-rc1
  and another Exynos clock patch which fixes a regression that prevents
  the video pipeline from functioning on that platform"

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
  clk: exynos4: Add CLK_GET_RATE_NOCACHE flag for the Exynos4x12 ISP clocks
  clk/zynq/clkc: Add CLK_SET_RATE_PARENT flag to ethernet muxes
  clk/zynq/clkc: Add dedicated spinlock for the SWDT