Linux would not connect to other router running old version Cisco IOS (12.0).
This is most likely a bug in that version of IOS, since it is fixed
in later versions. As a workaround this patch allows a module parameter
to be set to disable compressing the protocol ID.

See: https://bugzilla.vyatta.com/show_bug.cgi?id=3979

RFC 1990 allows an implementation to formulate MP fragments as if protocol
compression had been negotiated.  This allows us to always send compressed
protocol IDs.  But some implementations don't accept MP fragments with
compressed protocol IDs.  This parameter allows us to interoperate with
them.  The default value of the configurable parameter is the same as the
current behavior:  protocol compression is enabled.  If protocol compression
is disabled we will not send compressed protocol IDs.

This is based on an earlier patch by Bob Gilligan (using a sysctl).
Module parameter is writable to allow for enabling even if ppp
is already loaded for other uses.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch avoids disabling the vlan flags using ethtool.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A race exists when initializing ueagle-atm devices where the generic atm
device may not yet be created before the driver attempts to initialize
it's PHY signal state, which checks whether the atm device has been
created or not.  This often causes the sysfs 'carrier' attribute to be
'1' even though no signal has actually been found.

uea_probe
   usbatm_usb_probe
      driver->bind (uea_bind)
         uea_boot
            kthread_run(uea_kthread)     uea_kthread
      usbatm_atm_init                       uea_start_reset
         atm_dev_register                      UPDATE_ATM_SIGNAL

UPDATE_ATM_SIGNAL checks whether the ATM device has been created and if
not, will not update the PHY signal state.  Because of the race that
does not always happen in time, and the PHY signal state remains
ATM_PHY_SIG_FOUND even though no signal exists.

To fix the race, just create the kthread during initialization, and only
after initialization is complete, start the thread that reboots the
device and initializes PHY state.

[ 3030.490931] uea_probe: calling usbatm_usb_probe
[ 3030.490946] ueagle-atm 8-2:1.0: usbatm_usb_probe: trying driver ueagle-atm with vendor=1110, product=9031, ifnum  0
[ 3030.493691] uea_bind: setting usbatm
[ 3030.496932] usb 8-2: [ueagle-atm] using iso mode
[ 3030.497283] ueagle-atm 8-2:1.0: usbatm_usb_probe: using 3021 byte buffer for rx channel 0xffff880125953508
   <kthread already started before usbatm_usb_probe() has returned>
[ 3030.497292] usb 8-2: [ueagle-atm] (re)booting started
   <UPDATE_ATM_SIGNAL checks whether ATM device has been created yet before setting PHY state>
[ 3030.497298] uea_start_reset: atm dev (null)
   <and since it hasn't been created yet PHY state is not set>
[ 3030.497306] ueagle-atm 8-2:1.0: usbatm_usb_probe: using 3392 byte buffer for tx channel 0xffff8801259535b8
[ 3030.497374] usbatm_usb_probe: about to init
[ 3030.497379] usbatm_usb_probe: calling usbatm_atm_init
   <atm device finally gets created>
[ 3030.497384] usbatm_atm_init: creating atm device!
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
  ipv4: dont create routes on down devices
  epic100: hamachi: yellowfin: Fix skb allocation size
  sundance: Fix oopses with corrupted skb_shared_info
  Revert "ipv4: Allow configuring subnets as local addresses"
  USB: mcs7830: return negative if auto negotiate fails
  irda: prevent integer underflow in IRLMP_ENUMDEVICES
  tcp: fix listening_get_next()
  atl1c: Do not use legacy PCI power management
  mac80211: fix mesh forwarding
  MAINTAINERS: email address change
  net: Fix range checks in tcf_valid_offset().
  net_sched: sch_sfq: fix allot handling
  hostap: remove netif_stop_queue from init
  mac80211/rt2x00: add ieee80211_tx_status_ni()
  typhoon: memory corruption in typhoon_get_drvinfo()
  net: Add USB PID for new MOSCHIP USB ethernet controller MCS7832 variant
  net_sched: always clone skbs
  ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed.
  netlink: fix gcc -Wconversion compilation warning
  asix: add USB ID for Logitec LAN-GTJ U2A
  ...

In ip_route_output_slow(), instead of allowing a route to be created on
a not UPed device, report -ENETUNREACH immediately.

# ip tunnel add mode ipip remote 10.16.0.164 local
10.16.0.72 dev eth0
# (Note : tunl1 is down)
# ping -I tunl1 10.1.2.3
PING 10.1.2.3 (10.1.2.3) from 192.168.18.5 tunl1: 56(84) bytes of data.
(nothing)
# ./a.out tunl1
# ip tunnel del tunl1
Message from syslogd@shelby at Dec 22 10:12:08 ...
  kernel: unregister_netdevice: waiting for tunl1 to become free.
Usage count = 3

After patch:
# ping -I tunl1 10.1.2.3
connect: Network is unreachable
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joel Soete reported oopses during pppoe over sundance NIC, caused by
a bug in skb allocation and dma mapping code, where skb_reserve()
bytes weren't taken into account. As a followup to the patch:
"sundance: Fix oopses with corrupted skb_shared_info" very similar
code is fixed here for three other drivers.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Joel Soete <soete.joel@scarlet.be>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joel Soete reported oopses at the beginning of pppoe connections since
v2.6.35. After debugging the bug was found in sundance skb allocation
and dma mapping code, where skb_reserve() bytes aren't taken into
account. This is an old bug, only uncovered by some change in 2.6.35.

Initial debugging patch by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Joel Soete <soete.joel@scarlet.be>
Tested-by: Joel Soete <soete.joel@scarlet.be>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'merge' of git://git.secretlab.ca/git/linux-2.6:
  spi/mpc52xx-spi: fix annotation for remove()-pointer
  spi/fsl_espi: fix wrong setting of the address in the command buffer
  spi/fsl_espi: change the read behaviour of the SPIRF
  of/i2c: Fix request module by alias
  powerpc/mpc5200: include fs.h in mpc52xx_gpt.c

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: issue DIPM enable commands with LPM state updated
  libata: no special completion processing for EH commands
  pata_mpc52xx: driver needs BMDMA
  pata_cs5536: Add support for non-X86_32 platforms
  libata-sff: fix HSM_ST_ERR handling in __ata_sff_port_intr()

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: print out alloc information with KERN_DEBUG instead of KERN_INFO
  kthread_work: make lockdep happy

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] fix up documentation for change in ->queuecommand to lockless calling
  [SCSI] bfa: rename log_level to bfa_log_level

Low level drivers may behave differently depending on the current
link->lpm_policy.  During ata_eh_set_lpm(), DIPM enable commands are
issued after the successful completion of ap->ops->set_lpm(), which
means that the controller is already in the target state.  This causes
DIPM enable commands to be processed with mismatching controller power
state and link->lpm_policy value.

In ahci, link->lpm_policy is used to ignore certain PHY events if LPM
is enabled; however, as DIPM commands are issued with stale
link->lpm_policy, they sometimes end up triggering these conditions
and get aborted leading to LPM configuration failure.

Fix it by updating link->lpm_policy before issuing DIPM enable
commands.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

ata_qc_complete() contains special handling for certain commands.  For
example, it schedules EH for device revalidation after certain
configurations are changed.  These shouldn't be applied to EH
commands but they were.

In most cases, it doesn't cause an actual problem because EH doesn't
issue any command which would trigger special handling; however, ACPI
can issue such commands via _GTF which can cause weird interactions.

Restructure ata_qc_complete() such that EH commands are always passed
on to __ata_qc_complete().

stable: Please apply to -stable only after 2.6.38 is released.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Found by this build-error if BMDMA is disabled:

drivers/ata/pata_mpc52xx.c: In function 'mpc52xx_ata_init_one':
drivers/ata/pata_mpc52xx.c:662: error: 'ata_bmdma_interrupt' undeclared (first use in this function)
...

Move the Kconfig entry to the proper location as needed since
9a7780c9 (libata-sff: make BMDMA optional)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

pata_cs5536 does work on the other platforms(e.g. Loongson, a MIPS
variant), so, remove the dependency of X86_32 and fix the building
errors under the other platforms via only reserving the X86_32 specific
parts for X86_32.

pata_amd also supports cs5536 IDE controller, but this one saves about
33k for the compressed kernel image(vmlinuz for MIPS).
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Signed-off-by: Chen Jie <chenj@lemote.com>
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

While separating out BMDMA irq handler from SFF, commit c3b28894
(libata-sff: separate out BMDMA irq handler) incorrectly made
__ata_sff_port_intr() consider an IRQ to be an idle one if the host
state was transitioned to HSM_ST_ERR by ata_bmdma_port_intr().

This makes BMDMA drivers ignore IRQs reporting host bus error which
leads to timeouts instead of triggering EH immediately.  Fix it by
making __ata_sff_port_intr() consider the IRQ to be an idle one iff
the state is HSM_ST_IDLE.  This is equivalent to adding HSM_ST_ERR to
the "break"ing case but less error-prone.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Antonio Toma <antonio.toma@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Or else we can't operate on the right address when the trans length
is greater than 65535.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The user must read N bytes of SPIRF (1 <= N <= 4) that do not exceed the
amount of data in the receive FIFO, so read the SPIRF byte by byte when
the data in receive FIFO is less than 4 bytes.

On Simics, when read N bytes that exceed the amount of data in receive
FIFO, we can't read the data out, that is we can't clear the rx FIFO,
then the CPU will loop on the espi rx interrupt.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

If we are registering an i2c device that has a device tree node like
this real-world example:

      rtc@68 {
        compatible = "dallas,ds1337";
        reg = <0x68>;
      };

of_i2c_register_devices() will try to load a module called ds1337.ko.
There is no such module, so it will fail.  If we look in modules.alias
we will find entries like these:

.
.
.
alias i2c:ds1339 rtc_ds1307
alias i2c:ds1338 rtc_ds1307
alias i2c:ds1337 rtc_ds1307
alias i2c:ds1307 rtc_ds1307
alias i2c:ds1374 rtc_ds1374
.
.
.

The module we want is really called rtc_ds1307.ko.  If we request a
module called "i2c:ds1337", the userspace module loader will do the
right thing (unless it is busybox) and load rtc_ds1307.ko.  So we add
the I2C_MODULE_PREFIX to the request_module() string.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
  ocfs2: Fix system inodes cache overflow.
  ocfs2: Hold ip_lock when set/clear flags for indexed dir.
  ocfs2: Adjust masklog flag values
  Ocfs2: Teach 'coherency=full' O_DIRECT writes to correctly up_read i_alloc_sem.
  ocfs2/dlm: Migrate lockres with no locks if it has a reference

* 'linus-hot-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix on-line resizing regression

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Fix GPIO2-fixup for Sony laptops
  ALSA: hda - Try to find an empty control index when it's occupied
  ALSA: hda - Fix conflict of d-mic capture volume controls
  ALSA: hda - Don't apply ALC269-specific initialization to ALC275
  ALSA: hda - Add fix-up for Sony VAIO with ALC275 codecs
  ALSA: pcm: remember to always call va_end() on stuff that we va_start()
  ALSA: HDA: Add auto-mute for Thinkpad SL410/SL510

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (21 commits)
  [media] mceusb: set a default rx timeout
  [media] mceusb: fix inverted mask inversion logic
  [media] mceusb: add another Fintek device ID
  [media] lirc_dev: fixes in lirc_dev_fop_read()
  [media] lirc_dev: stray unlock in lirc_dev_fop_poll()
  [media] rc: fix sysfs entry for mceusb and streamzap
  [media] streamzap: merge timeout space with trailing space
  [media] mceusb: fix keybouce issue after parser simplification
  [media] IR: add tv power scancode to rc6 mce keymap
  [media] mceusb: buffer parsing fixups for 1st-gen device
  [media] mceusb: fix up reporting of trailing space
  [media] nuvoton-cir: improve buffer parsing responsiveness
  [media] mceusb: add support for Conexant Hybrid TV RDU253S
  [media] s5p-fimc: Fix output DMA handling in S5PV310 IP revisions
  [media] s5p-fimc: Use correct fourcc code for 32-bit RGB format
  [media] s5p-fimc: Convert m2m driver to unlocked_ioctl
  [media] s5p-fimc: Explicitly add required header file
  [media] s5p-fimc: Fix vidioc_g_crop/cropcap on camera sensor
  [media] s5p-fimc: BKL lock removal - compilation fix
  [media] soc-camera: fix static build of the sh_mobile_csi2.c driver
  ...

Merge branches 'perf-fixes-for-linus' and 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf probe: Fix to support libdwfl older than 0.148
  perf tools: Fix lazy wildcard matching
  perf buildid-list: Fix error return for success
  perf buildid-cache: Fix symbolic link handling
  perf symbols: Stop using vmlinux files with no symbols
  perf probe: Fix use of kernel image path given by 'k' option

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, kexec: Limit the crashkernel address appropriately

In construct_alloc_key(), up_write() is called in the error path if
__key_link_begin() fails, but this is incorrect as __key_link_begin() only
returns with the nominated keyring locked if it returns successfully.

Without this patch, you might see the following in dmesg:

	=====================================
	[ BUG: bad unlock balance detected! ]
	-------------------------------------
	mount.cifs/5769 is trying to release lock (&key->sem) at:
	[<ffffffff81201159>] request_key_and_link+0x263/0x3fc
	but there are no more locks to release!

	other info that might help us debug this:
	3 locks held by mount.cifs/5769:
	 #0:  (&type->s_umount_key#41/1){+.+.+.}, at: [<ffffffff81131321>] sget+0x278/0x3e7
	 #1:  (&ret_buf->session_mutex){+.+.+.}, at: [<ffffffffa0258e59>] cifs_get_smb_ses+0x35a/0x443 [cifs]
	 #2:  (root_key_user.cons_lock){+.+.+.}, at: [<ffffffff81201000>] request_key_and_link+0x10a/0x3fc

	stack backtrace:
	Pid: 5769, comm: mount.cifs Not tainted 2.6.37-rc6+ #1
	Call Trace:
	 [<ffffffff81201159>] ? request_key_and_link+0x263/0x3fc
	 [<ffffffff81081601>] print_unlock_inbalance_bug+0xca/0xd5
	 [<ffffffff81083248>] lock_release_non_nested+0xc1/0x263
	 [<ffffffff81201159>] ? request_key_and_link+0x263/0x3fc
	 [<ffffffff81201159>] ? request_key_and_link+0x263/0x3fc
	 [<ffffffff81083567>] lock_release+0x17d/0x1a4
	 [<ffffffff81073f45>] up_write+0x23/0x3b
	 [<ffffffff81201159>] request_key_and_link+0x263/0x3fc
	 [<ffffffffa026fe9e>] ? cifs_get_spnego_key+0x61/0x21f [cifs]
	 [<ffffffff812013c5>] request_key+0x41/0x74
	 [<ffffffffa027003d>] cifs_get_spnego_key+0x200/0x21f [cifs]
	 [<ffffffffa026e296>] CIFS_SessSetup+0x55d/0x1273 [cifs]
	 [<ffffffffa02589e1>] cifs_setup_session+0x90/0x1ae [cifs]
	 [<ffffffffa0258e7e>] cifs_get_smb_ses+0x37f/0x443 [cifs]
	 [<ffffffffa025a9e3>] cifs_mount+0x1aa1/0x23f3 [cifs]
	 [<ffffffff8111fd94>] ? alloc_debug_processing+0xdb/0x120
	 [<ffffffffa027002c>] ? cifs_get_spnego_key+0x1ef/0x21f [cifs]
	 [<ffffffffa024cc71>] cifs_do_mount+0x165/0x2b3 [cifs]
	 [<ffffffff81130e72>] vfs_kern_mount+0xaf/0x1dc
	 [<ffffffff81131007>] do_kern_mount+0x4d/0xef
	 [<ffffffff811483b9>] do_mount+0x6f4/0x733
	 [<ffffffff8114861f>] sys_mount+0x88/0xc2
	 [<ffffffff8100ac42>] system_call_fastpath+0x16/0x1b
Reported-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The default for non-READ_BACK GPIO regs is to have the clear bits set;
this means that our original errata fix was too simplistic.  This
changes it to the following behavior:

 - when setting GPIOs, ignore the higher order bits (they're for
   clearing, we don't need to care about them).

 - when clearing GPIOs, keep all the bits, but unset (via XOR) the
   lower order bit that negates the clear bit that we care about.  That
   is, if we're clearing GPIO 26 (val = 0x04000000), we first XOR what's
   currently in the register with 0x0400 (GPIO 26's SET bit), and then
   OR that with the GPIO 26's CLEAR bit.
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The edge detect status GPIOs function differently from the other atomic
model CS5536 GPIO registers; writing 1 to the high bits clears the GPIO,
but writing 1 to the lower bits also clears the bit.

This means that read-modify-write doesn't actually work for it, so don't
apply the errata here.  If a negative edge status gets lost after
resume..  well, we tried our best!
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit 4465b469.

Conflicts:

	net/ipv4/fib_frontend.c

As reported by Ben Greear, this causes regressions:

> Change 4465b469 caused rules
> to stop matching the input device properly because the
> FLOWI_FLAG_MATCH_ANY_IIF is always defined in ip_dev_find().
>
> This breaks rules such as:
>
> ip rule add pref 512 lookup local
> ip rule del pref 0 lookup local
> ip link set eth2 up
> ip -4 addr add 172.16.0.102/24 broadcast 172.16.0.255 dev eth2
> ip rule add to 172.16.0.102 iif eth2 lookup local pref 10
> ip rule add iif eth2 lookup 10001 pref 20
> ip route add 172.16.0.0/24 dev eth2 table 10001
> ip route add unreachable 0/0 table 10001
>
> If you had a second interface 'eth0' that was on a different
> subnet, pinging a system on that interface would fail:
>
>   [root@ct503-60 ~]# ping 192.168.100.1
>   connect: Invalid argument
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

https://bugzilla.kernel.org/show_bug.cgi?id=25352

This regression was caused by commit a31437b8: "ext4: use
sb_issue_zeroout in setup_new_group_blocks", by accidentally dropping
the code which reserved the block group descriptor and inode table
blocks.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

Fix build errors like these (from a randconfig and my defconfig for a custom board):

src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:549: error: dereferencing pointer to incomplete type: 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:636: error: implicit declaration of function 'nonseekable_open': 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:657: error: variable 'mpc52xx_wdt_fops' has initializer but incomplete type: 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:658: error: excess elements in struct initializer: 1 errors in 1 logs
src/arch/powerpc/platforms/52xx/mpc52xx_gpt.c:658: error: unknown field 'owner' specified in initializer: 1 errors in 1 logs
...
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The original code returns 0 on success and 1 on failure.  In fact, at
this point, "ret" is already either zero or a negative error code so
we can just return it directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the user-provided len is less than the expected offset, the
IRLMP_ENUMDEVICES getsockopt will do a copy_to_user() with a very large
size value.  While this isn't be a security issue on x86 because it will
get caught by the access_ok() check, it may leak large amounts of kernel
heap on other architectures.  In any event, this patch fixes it.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexey Vlasov found /proc/net/tcp could sometime loop and display
millions of sockets in LISTEN state.

In 2.6.29, when we converted TCP hash tables to RCU, we left two
sk_next() calls in listening_get_next().

We must instead use sk_nulls_next() to properly detect an end of chain.
Reported-by: Alexey Vlasov <renton@renton.name>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fix-up entries by the commit 2785591a
     ALSA: hda - Add fix-up for Sony VAIO with ALC275 codecs
weren't applied in the right position.  They had to be before the quirk
entry matching to all Sony devices.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When a mixer control element was already created with the given name,
try to find another index for avoiding conflicts, instead of breaking
with an error.  This makes the driver more robust.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When the d-mics are assigned to the same purpose of another analog mic
pins, the driver doesn't compute the index properly, resulting in an
error with "existing control".  This patch fixes it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm: Include the connector name in the output_poll_execute() debug message
  drm/radeon/kms: fix bug in r600_gpu_is_lockup
  drm/radeon/kms: reorder display resume to avoid problems
  drm/radeon/kms/evergreen: reset the grbm blocks at resume and init
  drm/radeon/kms: fix evergreen asic reset
  Revert "drm: Don't try and disable an encoder that was never enabled"
  drm/radeon: Add early unregister of firmware fb's
  drm/radeon: use aperture size not vram size for overlap tests
  drm/radeon/kms/evergreen: flush hdp cache when flushing gart tlb
  drm/radeon/kms: disable the r600 cb offset checker for linear surfaces
  drm/radeon/kms: disable ss fixed ref divide
  drm/i915/bios: Reverse order of 100/120 Mhz SSC clocks
  agp/intel: Fix missed cached memory flags setting in i965_write_entry()
  drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
  drm/i915/ringbuffer: Handle wrapping of the autoreported HEAD
  drm/i915/dp: Fix I2C/EDID handling with active DisplayPort to DVI converter