- 01 Mar, 2020 1 commit
-
-
You-Sheng Yang authored
Dell USB Type C docking WD19/WD19DC attaches additional peripherals as: /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/6p, 5000M |__ Port 1: Dev 11, If 0, Class=Hub, Driver=hub/4p, 5000M |__ Port 3: Dev 12, If 0, Class=Hub, Driver=hub/4p, 5000M |__ Port 4: Dev 13, If 0, Class=Vendor Specific Class, Driver=r8152, 5000M where usb 2-1-3 is a hub connecting all USB Type-A/C ports on the dock. When hotplugging such dock with additional usb devices already attached on it, the probing process may reset usb 2.1 port, therefore r8152 ethernet device is also reset. However, during r8152 device init there are several for-loops that, when it's unable to retrieve hardware registers due to being disconnected from USB, may take up to 14 seconds each in practice, and that has to be completed before USB may re-enumerate devices on the bus. As a result, devices attached to the dock will only be available after nearly 1 minute after the dock was plugged in: [ 216.388290] [250] r8152 2-1.4:1.0: usb_probe_interface [ 216.388292] [250] r8152 2-1.4:1.0: usb_probe_interface - got id [ 258.830410] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): PHY not ready [ 258.830460] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Invalid header when reading pass-thru MAC addr [ 258.830464] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail This happens in, for example, r8153_init: static int generic_ocp_read(struct r8152 *tp, u16 index, u16 size, void *data, u16 type) { if (test_bit(RTL8152_UNPLUG, &tp->flags)) return -ENODEV; ... } static u16 ocp_read_word(struct r8152 *tp, u16 type, u16 index) { u32 data; ... generic_ocp_read(tp, index, sizeof(tmp), &tmp, type | byen); data = __le32_to_cpu(tmp); ... return (u16)data; } static void r8153_init(struct r8152 *tp) { ... if (test_bit(RTL8152_UNPLUG, &tp->flags)) return; for (i = 0; i < 500; i++) { if (ocp_read_word(tp, MCU_TYPE_PLA, PLA_BOOT_CTRL) & AUTOLOAD_DONE) break; msleep(20); } ... } Since ocp_read_word() doesn't check the return status of generic_ocp_read(), and the only exit condition for the loop is to have a match in the returned value, such loops will only ends after exceeding its maximum runs when the device has been marked as disconnected, which takes 500 * 20ms = 10 seconds in theory, 14 in practice. To solve this long latency another test to RTL8152_UNPLUG flag should be added after those 20ms sleep to skip unnecessary loops, so that the device probe can complete early and proceed to parent port reset/reprobe process. This can be reproduced on all kernel versions up to latest v5.6-rc2, but after v5.5-rc7 the reproduce rate is dramatically lowered to 1/30 or less while it was around 1/2. Signed-off-by: You-Sheng Yang <vicamo.yang@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 28 Feb, 2020 1 commit
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix leak in nl80211 AP start where we leak the ACL memory, from Johannes Berg. 2) Fix double mutex unlock in mac80211, from Andrei Otcheretianski. 3) Fix RCU stall in ipset, from Jozsef Kadlecsik. 4) Fix devlink locking in devlink_dpipe_table_register, from Madhuparna Bhowmik. 5) Fix race causing TX hang in ll_temac, from Esben Haabendal. 6) Stale eth hdr pointer in br_dev_xmit(), from Nikolay Aleksandrov. 7) Fix TX hash calculation bounds checking wrt. tc rules, from Amritha Nambiar. 8) Size netlink responses properly in schedule action code to take into consideration TCA_ACT_FLAGS. From Jiri Pirko. 9) Fix firmware paths for mscc PHY driver, from Antoine Tenart. 10) Don't register stmmac notifier multiple times, from Aaro Koskinen. 11) Various rmnet bug fixes, from Taehee Yoo. 12) Fix vsock deadlock in vsock transport release, from Stefano Garzarella. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (61 commits) net: dsa: mv88e6xxx: Fix masking of egress port mlxsw: pci: Wait longer before accessing the device after reset sfc: fix timestamp reconstruction at 16-bit rollover points vsock: fix potential deadlock in transport->release() unix: It's CONFIG_PROC_FS not CONFIG_PROCFS net: rmnet: fix packet forwarding in rmnet bridge mode net: rmnet: fix bridge mode bugs net: rmnet: use upper/lower device infrastructure net: rmnet: do not allow to change mux id if mux id is duplicated net: rmnet: remove rcu_read_lock in rmnet_force_unassociate_device() net: rmnet: fix suspicious RCU usage net: rmnet: fix NULL pointer dereference in rmnet_changelink() net: rmnet: fix NULL pointer dereference in rmnet_newlink() net: phy: marvell: don't interpret PHY status unless resolved mlx5: register lag notifier for init network namespace only unix: define and set show_fdinfo only if procfs is enabled hinic: fix a bug of rss configuration hinic: fix a bug of setting hw_ioctxt hinic: fix a irq affinity bug net/smc: check for valid ib_client_data ...
-
- 27 Feb, 2020 38 commits
-
-
Andrew Lunn authored
Add missing ~ to the usage of the mask. Reported-by: Kevin Benson <Kevin.Benson@zii.aero> Reported-by: Chris Healy <Chris.Healy@zii.aero> Fixes: 5c74c54c ("net: dsa: mv88e6xxx: Split monitor port configuration") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Amit Cohen authored
During initialization the driver issues a reset to the device and waits for 100ms before checking if the firmware is ready. The waiting is necessary because before that the device is irresponsive and the first read can result in a completion timeout. While 100ms is sufficient for Spectrum-1 and Spectrum-2, it is insufficient for Spectrum-3. Fix this by increasing the timeout to 200ms. Fixes: da382875 ("mlxsw: spectrum: Extend to support Spectrum-3 ASIC") Signed-off-by: Amit Cohen <amitc@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Alex Maftei (amaftei) authored
We can't just use the top bits of the last sync event as they could be off-by-one every 65,536 seconds, giving an error in reconstruction of 65,536 seconds. This patch uses the difference in the bottom 16 bits (mod 2^16) to calculate an offset that needs to be applied to the last sync event to get to the current time. Signed-off-by: Alexandru-Mihai Maftei <amaftei@solarflare.com> Acked-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Stefano Garzarella authored
Some transports (hyperv, virtio) acquire the sock lock during the .release() callback. In the vsock_stream_connect() we call vsock_assign_transport(); if the socket was previously assigned to another transport, the vsk->transport->release() is called, but the sock lock is already held in the vsock_stream_connect(), causing a deadlock reported by syzbot: INFO: task syz-executor280:9768 blocked for more than 143 seconds. Not tainted 5.6.0-rc1-syzkaller #0 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. syz-executor280 D27912 9768 9766 0x00000000 Call Trace: context_switch kernel/sched/core.c:3386 [inline] __schedule+0x934/0x1f90 kernel/sched/core.c:4082 schedule+0xdc/0x2b0 kernel/sched/core.c:4156 __lock_sock+0x165/0x290 net/core/sock.c:2413 lock_sock_nested+0xfe/0x120 net/core/sock.c:2938 virtio_transport_release+0xc4/0xd60 net/vmw_vsock/virtio_transport_common.c:832 vsock_assign_transport+0xf3/0x3b0 net/vmw_vsock/af_vsock.c:454 vsock_stream_connect+0x2b3/0xc70 net/vmw_vsock/af_vsock.c:1288 __sys_connect_file+0x161/0x1c0 net/socket.c:1857 __sys_connect+0x174/0x1b0 net/socket.c:1874 __do_sys_connect net/socket.c:1885 [inline] __se_sys_connect net/socket.c:1882 [inline] __x64_sys_connect+0x73/0xb0 net/socket.c:1882 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe To avoid this issue, this patch remove the lock acquiring in the .release() callback of hyperv and virtio transports, and it holds the lock when we call vsk->transport->release() in the vsock core. Reported-by: syzbot+731710996d79d0d58fbc@syzkaller.appspotmail.com Fixes: 408624af ("vsock: use local transport when it is loaded") Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Fixes: 3a12500e ("unix: define and set show_fdinfo only if procfs is enabled") Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Taehee Yoo says: ==================== net: rmnet: fix several bugs This patchset is to fix several bugs in RMNET module. 1. The first patch fixes NULL-ptr-deref in rmnet_newlink(). When rmnet interface is being created, it uses IFLA_LINK without checking NULL. So, if userspace doesn't set IFLA_LINK, panic will occur. In this patch, checking NULL pointer code is added. 2. The second patch fixes NULL-ptr-deref in rmnet_changelink(). To get real device in rmnet_changelink(), it uses IFLA_LINK. But, IFLA_LINK should not be used in rmnet_changelink(). 3. The third patch fixes suspicious RCU usage in rmnet_get_port(). rmnet_get_port() uses rcu_dereference_rtnl(). But, rmnet_get_port() is used by datapath. So, rcu_dereference_bh() should be used instead of rcu_dereference_rtnl(). 4. The fourth patch fixes suspicious RCU usage in rmnet_force_unassociate_device(). RCU critical section should not be scheduled. But, unregister_netdevice_queue() in the rmnet_force_unassociate_device() would be scheduled. So, the RCU warning occurs. In this patch, the rcu_read_lock() in the rmnet_force_unassociate_device() is removed because it's unnecessary. 5. The fifth patch fixes duplicate MUX ID case. RMNET MUX ID is unique. So, rmnet interface isn't allowed to be created, which have a duplicate MUX ID. But, only rmnet_newlink() checks this condition, rmnet_changelink() doesn't check this. So, duplicate MUX ID case would happen. 6. The sixth patch fixes upper/lower interface relationship problems. When IFLA_LINK is used, the upper/lower infrastructure should be used. Because it checks the maximum depth of upper/lower interfaces and it also checks circular interface relationship, etc. In this patch, netdev_upper_dev_link() is used. 7. The seventh patch fixes bridge related problems. a) ->ndo_del_slave() doesn't work. b) It couldn't detect circular upper/lower interface relationship. c) It couldn't prevent stack overflow because of too deep depth of upper/lower interface d) It doesn't check the number of lower interfaces. e) Panics because of several reasons. These problems are actually the same problem. So, this patch fixes these problems. 8. The eighth patch fixes packet forwarding issue in bridge mode Packet forwarding is not working in rmnet bridge mode. Because when a packet is forwarded, skb_push() for an ethernet header is needed. But it doesn't call skb_push(). So, the ethernet header will be lost. Change log: - update commit logs. - drop two patches in this patchset because of wrong target branch. - ("net: rmnet: add missing module alias") - ("net: rmnet: print error message when command fails") - remove unneessary rcu_read_lock() in the third patch. - use rcu_dereference_bh() instead of rcu_dereference in third patch. - do not allow to add a bridge device if rmnet interface is already bridge mode in the seventh patch. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
Packet forwarding is not working in rmnet bridge mode. Because when a packet is forwarded, skb_push() for an ethernet header is needed. But it doesn't call skb_push(). So, the ethernet header will be lost. Test commands: modprobe rmnet ip netns add nst ip netns add nst2 ip link add veth0 type veth peer name veth1 ip link add veth2 type veth peer name veth3 ip link set veth1 netns nst ip link set veth3 netns nst2 ip link add rmnet0 link veth0 type rmnet mux_id 1 ip link set veth2 master rmnet0 ip link set veth0 up ip link set veth2 up ip link set rmnet0 up ip a a 192.168.100.1/24 dev rmnet0 ip netns exec nst ip link set veth1 up ip netns exec nst ip a a 192.168.100.2/24 dev veth1 ip netns exec nst2 ip link set veth3 up ip netns exec nst2 ip a a 192.168.100.3/24 dev veth3 ip netns exec nst2 ping 192.168.100.2 Fixes: 60d58f97 ("net: qualcomm: rmnet: Implement bridge mode") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
In order to attach a bridge interface to the rmnet interface, "master" operation is used. (e.g. ip link set dummy1 master rmnet0) But, in the rmnet_add_bridge(), which is a callback of ->ndo_add_slave() doesn't register lower interface. So, ->ndo_del_slave() doesn't work. There are other problems too. 1. It couldn't detect circular upper/lower interface relationship. 2. It couldn't prevent stack overflow because of too deep depth of upper/lower interface 3. It doesn't check the number of lower interfaces. 4. Panics because of several reasons. The root problem of these issues is actually the same. So, in this patch, these all problems will be fixed. Test commands: modprobe rmnet ip link add dummy0 type dummy ip link add rmnet0 link dummy0 type rmnet mux_id 1 ip link add dummy1 master rmnet0 type dummy ip link add dummy2 master rmnet0 type dummy ip link del rmnet0 ip link del dummy2 ip link del dummy1 Splat looks like: [ 41.867595][ T1164] general protection fault, probably for non-canonical address 0xdffffc0000000101I [ 41.869993][ T1164] KASAN: null-ptr-deref in range [0x0000000000000808-0x000000000000080f] [ 41.872950][ T1164] CPU: 0 PID: 1164 Comm: ip Not tainted 5.6.0-rc1+ #447 [ 41.873915][ T1164] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 41.875161][ T1164] RIP: 0010:rmnet_unregister_bridge.isra.6+0x71/0xf0 [rmnet] [ 41.876178][ T1164] Code: 48 89 ef 48 89 c6 5b 5d e9 fc fe ff ff e8 f7 f3 ff ff 48 8d b8 08 08 00 00 48 ba 00 7 [ 41.878925][ T1164] RSP: 0018:ffff8880c4d0f188 EFLAGS: 00010202 [ 41.879774][ T1164] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000101 [ 41.887689][ T1164] RDX: dffffc0000000000 RSI: ffffffffb8cf64f0 RDI: 0000000000000808 [ 41.888727][ T1164] RBP: ffff8880c40e4000 R08: ffffed101b3c0e3c R09: 0000000000000001 [ 41.889749][ T1164] R10: 0000000000000001 R11: ffffed101b3c0e3b R12: 1ffff110189a1e3c [ 41.890783][ T1164] R13: ffff8880c4d0f200 R14: ffffffffb8d56160 R15: ffff8880ccc2c000 [ 41.891794][ T1164] FS: 00007f4300edc0c0(0000) GS:ffff8880d9c00000(0000) knlGS:0000000000000000 [ 41.892953][ T1164] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 41.893800][ T1164] CR2: 00007f43003bc8c0 CR3: 00000000ca53e001 CR4: 00000000000606f0 [ 41.894824][ T1164] Call Trace: [ 41.895274][ T1164] ? rcu_is_watching+0x2c/0x80 [ 41.895895][ T1164] rmnet_config_notify_cb+0x1f7/0x590 [rmnet] [ 41.896687][ T1164] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet] [ 41.897611][ T1164] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet] [ 41.898508][ T1164] ? __module_text_address+0x13/0x140 [ 41.899162][ T1164] notifier_call_chain+0x90/0x160 [ 41.899814][ T1164] rollback_registered_many+0x660/0xcf0 [ 41.900544][ T1164] ? netif_set_real_num_tx_queues+0x780/0x780 [ 41.901316][ T1164] ? __lock_acquire+0xdfe/0x3de0 [ 41.901958][ T1164] ? memset+0x1f/0x40 [ 41.902468][ T1164] ? __nla_validate_parse+0x98/0x1ab0 [ 41.903166][ T1164] unregister_netdevice_many.part.133+0x13/0x1b0 [ 41.903988][ T1164] rtnl_delete_link+0xbc/0x100 [ ... ] Fixes: 60d58f97 ("net: qualcomm: rmnet: Implement bridge mode") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
netdev_upper_dev_link() is useful to manage lower/upper interfaces. And this function internally validates looping, maximum depth. All or most virtual interfaces that could have a real interface (e.g. macsec, macvlan, ipvlan etc.) use lower/upper infrastructure. Test commands: modprobe rmnet ip link add dummy0 type dummy ip link add rmnet1 link dummy0 type rmnet mux_id 1 for i in {2..100} do let A=$i-1 ip link add rmnet$i link rmnet$A type rmnet mux_id $i done ip link del dummy0 The purpose of the test commands is to make stack overflow. Splat looks like: [ 52.411438][ T1395] BUG: KASAN: slab-out-of-bounds in find_busiest_group+0x27e/0x2c00 [ 52.413218][ T1395] Write of size 64 at addr ffff8880c774bde0 by task ip/1395 [ 52.414841][ T1395] [ 52.430720][ T1395] CPU: 1 PID: 1395 Comm: ip Not tainted 5.6.0-rc1+ #447 [ 52.496511][ T1395] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 52.513597][ T1395] Call Trace: [ 52.546516][ T1395] [ 52.558773][ T1395] Allocated by task 3171537984: [ 52.588290][ T1395] BUG: unable to handle page fault for address: ffffffffb999e260 [ 52.589311][ T1395] #PF: supervisor read access in kernel mode [ 52.590529][ T1395] #PF: error_code(0x0000) - not-present page [ 52.591374][ T1395] PGD d6818067 P4D d6818067 PUD d6819063 PMD 0 [ 52.592288][ T1395] Thread overran stack, or stack corrupted [ 52.604980][ T1395] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI [ 52.605856][ T1395] CPU: 1 PID: 1395 Comm: ip Not tainted 5.6.0-rc1+ #447 [ 52.611764][ T1395] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 52.621520][ T1395] RIP: 0010:stack_depot_fetch+0x10/0x30 [ 52.622296][ T1395] Code: ff e9 f9 fe ff ff 48 89 df e8 9c 1d 91 ff e9 ca fe ff ff cc cc cc cc cc cc cc 89 f8 0 [ 52.627887][ T1395] RSP: 0018:ffff8880c774bb60 EFLAGS: 00010006 [ 52.628735][ T1395] RAX: 00000000001f8880 RBX: ffff8880c774d140 RCX: 0000000000000000 [ 52.631773][ T1395] RDX: 000000000000001d RSI: ffff8880c774bb68 RDI: 0000000000003ff0 [ 52.649584][ T1395] RBP: ffffea00031dd200 R08: ffffed101b43e403 R09: ffffed101b43e403 [ 52.674857][ T1395] R10: 0000000000000001 R11: ffffed101b43e402 R12: ffff8880d900e5c0 [ 52.678257][ T1395] R13: ffff8880c774c000 R14: 0000000000000000 R15: dffffc0000000000 [ 52.694541][ T1395] FS: 00007fe867f6e0c0(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000 [ 52.764039][ T1395] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 52.815008][ T1395] CR2: ffffffffb999e260 CR3: 00000000c26aa005 CR4: 00000000000606e0 [ 52.862312][ T1395] Call Trace: [ 52.887133][ T1395] Modules linked in: dummy rmnet veth openvswitch nsh nf_conncount nf_nat nf_conntrack nf_dex [ 52.936749][ T1395] CR2: ffffffffb999e260 [ 52.965695][ T1395] ---[ end trace 7e32ca99482dbb31 ]--- [ 52.966556][ T1395] RIP: 0010:stack_depot_fetch+0x10/0x30 [ 52.971083][ T1395] Code: ff e9 f9 fe ff ff 48 89 df e8 9c 1d 91 ff e9 ca fe ff ff cc cc cc cc cc cc cc 89 f8 0 [ 53.003650][ T1395] RSP: 0018:ffff8880c774bb60 EFLAGS: 00010006 [ 53.043183][ T1395] RAX: 00000000001f8880 RBX: ffff8880c774d140 RCX: 0000000000000000 [ 53.076480][ T1395] RDX: 000000000000001d RSI: ffff8880c774bb68 RDI: 0000000000003ff0 [ 53.093858][ T1395] RBP: ffffea00031dd200 R08: ffffed101b43e403 R09: ffffed101b43e403 [ 53.112795][ T1395] R10: 0000000000000001 R11: ffffed101b43e402 R12: ffff8880d900e5c0 [ 53.139837][ T1395] R13: ffff8880c774c000 R14: 0000000000000000 R15: dffffc0000000000 [ 53.141500][ T1395] FS: 00007fe867f6e0c0(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000 [ 53.143343][ T1395] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 53.152007][ T1395] CR2: ffffffffb999e260 CR3: 00000000c26aa005 CR4: 00000000000606e0 [ 53.156459][ T1395] Kernel panic - not syncing: Fatal exception [ 54.213570][ T1395] Shutting down cpus with NMI [ 54.354112][ T1395] Kernel Offset: 0x33000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0x) [ 54.355687][ T1395] Rebooting in 5 seconds.. Fixes: b37f78f2 ("net: qualcomm: rmnet: Fix crash on real dev unregistration") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
Basically, duplicate mux id isn't be allowed. So, the creation of rmnet will be failed if there is duplicate mux id is existing. But, changelink routine doesn't check duplicate mux id. Test commands: modprobe rmnet ip link add dummy0 type dummy ip link add rmnet0 link dummy0 type rmnet mux_id 1 ip link add rmnet1 link dummy0 type rmnet mux_id 2 ip link set rmnet1 type rmnet mux_id 1 Fixes: 23790ef1 ("net: qualcomm: rmnet: Allow to configure flags for existing devices") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
The notifier_call() of the slave interface removes rmnet interface with unregister_netdevice_queue(). But, before calling unregister_netdevice_queue(), it acquires rcu readlock. In the RCU critical section, sleeping isn't be allowed. But, unregister_netdevice_queue() internally calls synchronize_net(), which would sleep. So, suspicious RCU usage warning occurs. Test commands: modprobe rmnet ip link add dummy0 type dummy ip link add dummy1 type dummy ip link add rmnet0 link dummy0 type rmnet mux_id 1 ip link set dummy1 master rmnet0 ip link del dummy0 Splat looks like: [ 79.639245][ T1195] ============================= [ 79.640134][ T1195] WARNING: suspicious RCU usage [ 79.640852][ T1195] 5.6.0-rc1+ #447 Not tainted [ 79.641657][ T1195] ----------------------------- [ 79.642472][ T1195] ./include/linux/rcupdate.h:273 Illegal context switch in RCU read-side critical section! [ 79.644043][ T1195] [ 79.644043][ T1195] other info that might help us debug this: [ 79.644043][ T1195] [ 79.645682][ T1195] [ 79.645682][ T1195] rcu_scheduler_active = 2, debug_locks = 1 [ 79.646980][ T1195] 2 locks held by ip/1195: [ 79.647629][ T1195] #0: ffffffffa3cf64f0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x457/0x890 [ 79.649312][ T1195] #1: ffffffffa39256c0 (rcu_read_lock){....}, at: rmnet_config_notify_cb+0xf0/0x590 [rmnet] [ 79.651717][ T1195] [ 79.651717][ T1195] stack backtrace: [ 79.652650][ T1195] CPU: 3 PID: 1195 Comm: ip Not tainted 5.6.0-rc1+ #447 [ 79.653702][ T1195] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 79.655037][ T1195] Call Trace: [ 79.655560][ T1195] dump_stack+0x96/0xdb [ 79.656252][ T1195] ___might_sleep+0x345/0x440 [ 79.656994][ T1195] synchronize_net+0x18/0x30 [ 79.661132][ T1195] netdev_rx_handler_unregister+0x40/0xb0 [ 79.666266][ T1195] rmnet_unregister_real_device+0x42/0xb0 [rmnet] [ 79.667211][ T1195] rmnet_config_notify_cb+0x1f7/0x590 [rmnet] [ 79.668121][ T1195] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet] [ 79.669166][ T1195] ? rmnet_unregister_bridge.isra.6+0xf0/0xf0 [rmnet] [ 79.670286][ T1195] ? __module_text_address+0x13/0x140 [ 79.671139][ T1195] notifier_call_chain+0x90/0x160 [ 79.671973][ T1195] rollback_registered_many+0x660/0xcf0 [ 79.672893][ T1195] ? netif_set_real_num_tx_queues+0x780/0x780 [ 79.675091][ T1195] ? __lock_acquire+0xdfe/0x3de0 [ 79.675825][ T1195] ? memset+0x1f/0x40 [ 79.676367][ T1195] ? __nla_validate_parse+0x98/0x1ab0 [ 79.677290][ T1195] unregister_netdevice_many.part.133+0x13/0x1b0 [ 79.678163][ T1195] rtnl_delete_link+0xbc/0x100 [ ... ] Fixes: ceed73a2 ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
rmnet_get_port() internally calls rcu_dereference_rtnl(), which checks RTNL. But rmnet_get_port() could be called by packet path. The packet path is not protected by RTNL. So, the suspicious RCU usage problem occurs. Test commands: modprobe rmnet ip netns add nst ip link add veth0 type veth peer name veth1 ip link set veth1 netns nst ip link add rmnet0 link veth0 type rmnet mux_id 1 ip netns exec nst ip link add rmnet1 link veth1 type rmnet mux_id 1 ip netns exec nst ip link set veth1 up ip netns exec nst ip link set rmnet1 up ip netns exec nst ip a a 192.168.100.2/24 dev rmnet1 ip link set veth0 up ip link set rmnet0 up ip a a 192.168.100.1/24 dev rmnet0 ping 192.168.100.2 Splat looks like: [ 146.630958][ T1174] WARNING: suspicious RCU usage [ 146.631735][ T1174] 5.6.0-rc1+ #447 Not tainted [ 146.632387][ T1174] ----------------------------- [ 146.633151][ T1174] drivers/net/ethernet/qualcomm/rmnet/rmnet_config.c:386 suspicious rcu_dereference_check() ! [ 146.634742][ T1174] [ 146.634742][ T1174] other info that might help us debug this: [ 146.634742][ T1174] [ 146.645992][ T1174] [ 146.645992][ T1174] rcu_scheduler_active = 2, debug_locks = 1 [ 146.646937][ T1174] 5 locks held by ping/1174: [ 146.647609][ T1174] #0: ffff8880c31dea70 (sk_lock-AF_INET){+.+.}, at: raw_sendmsg+0xab8/0x2980 [ 146.662463][ T1174] #1: ffffffff93925660 (rcu_read_lock_bh){....}, at: ip_finish_output2+0x243/0x2150 [ 146.671696][ T1174] #2: ffffffff93925660 (rcu_read_lock_bh){....}, at: __dev_queue_xmit+0x213/0x2940 [ 146.673064][ T1174] #3: ffff8880c19ecd58 (&dev->qdisc_running_key#7){+...}, at: ip_finish_output2+0x714/0x2150 [ 146.690358][ T1174] #4: ffff8880c5796898 (&dev->qdisc_xmit_lock_key#3){+.-.}, at: sch_direct_xmit+0x1e2/0x1020 [ 146.699875][ T1174] [ 146.699875][ T1174] stack backtrace: [ 146.701091][ T1174] CPU: 0 PID: 1174 Comm: ping Not tainted 5.6.0-rc1+ #447 [ 146.705215][ T1174] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 146.706565][ T1174] Call Trace: [ 146.707102][ T1174] dump_stack+0x96/0xdb [ 146.708007][ T1174] rmnet_get_port.part.9+0x76/0x80 [rmnet] [ 146.709233][ T1174] rmnet_egress_handler+0x107/0x420 [rmnet] [ 146.710492][ T1174] ? sch_direct_xmit+0x1e2/0x1020 [ 146.716193][ T1174] rmnet_vnd_start_xmit+0x3d/0xa0 [rmnet] [ 146.717012][ T1174] dev_hard_start_xmit+0x160/0x740 [ 146.717854][ T1174] sch_direct_xmit+0x265/0x1020 [ 146.718577][ T1174] ? register_lock_class+0x14d0/0x14d0 [ 146.719429][ T1174] ? dev_watchdog+0xac0/0xac0 [ 146.723738][ T1174] ? __dev_queue_xmit+0x15fd/0x2940 [ 146.724469][ T1174] ? lock_acquire+0x164/0x3b0 [ 146.725172][ T1174] __dev_queue_xmit+0x20c7/0x2940 [ ... ] Fixes: ceed73a2 ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
In the rmnet_changelink(), it uses IFLA_LINK without checking NULL pointer. tb[IFLA_LINK] could be NULL pointer. So, NULL-ptr-deref could occur. rmnet already has a lower interface (real_dev). So, after this patch, rmnet_changelink() does not use IFLA_LINK anymore. Test commands: modprobe rmnet ip link add dummy0 type dummy ip link add rmnet0 link dummy0 type rmnet mux_id 1 ip link set rmnet0 type rmnet mux_id 2 Splat looks like: [ 90.578726][ T1131] general protection fault, probably for non-canonical address 0xdffffc0000000000I [ 90.581121][ T1131] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] [ 90.582380][ T1131] CPU: 2 PID: 1131 Comm: ip Not tainted 5.6.0-rc1+ #447 [ 90.584285][ T1131] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 90.587506][ T1131] RIP: 0010:rmnet_changelink+0x5a/0x8a0 [rmnet] [ 90.588546][ T1131] Code: 83 ec 20 48 c1 ea 03 80 3c 02 00 0f 85 6f 07 00 00 48 8b 5e 28 48 b8 00 00 00 00 00 0 [ 90.591447][ T1131] RSP: 0018:ffff8880ce78f1b8 EFLAGS: 00010247 [ 90.592329][ T1131] RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffff8880ce78f8b0 [ 90.593253][ T1131] RDX: 0000000000000000 RSI: ffff8880ce78f4a0 RDI: 0000000000000004 [ 90.594058][ T1131] RBP: ffff8880cf543e00 R08: 0000000000000002 R09: 0000000000000002 [ 90.594859][ T1131] R10: ffffffffc0586a40 R11: 0000000000000000 R12: ffff8880ca47c000 [ 90.595690][ T1131] R13: ffff8880ca47c000 R14: ffff8880cf545000 R15: 0000000000000000 [ 90.596553][ T1131] FS: 00007f21f6c7e0c0(0000) GS:ffff8880da400000(0000) knlGS:0000000000000000 [ 90.597504][ T1131] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 90.599418][ T1131] CR2: 0000556e413db458 CR3: 00000000c917a002 CR4: 00000000000606e0 [ 90.600289][ T1131] Call Trace: [ 90.600631][ T1131] __rtnl_newlink+0x922/0x1270 [ 90.601194][ T1131] ? lock_downgrade+0x6e0/0x6e0 [ 90.601724][ T1131] ? rtnl_link_unregister+0x220/0x220 [ 90.602309][ T1131] ? lock_acquire+0x164/0x3b0 [ 90.602784][ T1131] ? is_bpf_image_address+0xff/0x1d0 [ 90.603331][ T1131] ? rtnl_newlink+0x4c/0x90 [ 90.603810][ T1131] ? kernel_text_address+0x111/0x140 [ 90.604419][ T1131] ? __kernel_text_address+0xe/0x30 [ 90.604981][ T1131] ? unwind_get_return_address+0x5f/0xa0 [ 90.605616][ T1131] ? create_prof_cpu_mask+0x20/0x20 [ 90.606304][ T1131] ? arch_stack_walk+0x83/0xb0 [ 90.606985][ T1131] ? stack_trace_save+0x82/0xb0 [ 90.607656][ T1131] ? stack_trace_consume_entry+0x160/0x160 [ 90.608503][ T1131] ? deactivate_slab.isra.78+0x2c5/0x800 [ 90.609336][ T1131] ? kasan_unpoison_shadow+0x30/0x40 [ 90.610096][ T1131] ? kmem_cache_alloc_trace+0x135/0x350 [ 90.610889][ T1131] ? rtnl_newlink+0x4c/0x90 [ 90.611512][ T1131] rtnl_newlink+0x65/0x90 [ ... ] Fixes: 23790ef1 ("net: qualcomm: rmnet: Allow to configure flags for existing devices") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
rmnet registers IFLA_LINK interface as a lower interface. But, IFLA_LINK could be NULL. In the current code, rmnet doesn't check IFLA_LINK. So, panic would occur. Test commands: modprobe rmnet ip link add rmnet0 type rmnet mux_id 1 Splat looks like: [ 36.826109][ T1115] general protection fault, probably for non-canonical address 0xdffffc0000000000I [ 36.838817][ T1115] KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007] [ 36.839908][ T1115] CPU: 1 PID: 1115 Comm: ip Not tainted 5.6.0-rc1+ #447 [ 36.840569][ T1115] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 36.841408][ T1115] RIP: 0010:rmnet_newlink+0x54/0x510 [rmnet] [ 36.841986][ T1115] Code: 83 ec 18 48 c1 e9 03 80 3c 01 00 0f 85 d4 03 00 00 48 8b 6a 28 48 b8 00 00 00 00 00 c [ 36.843923][ T1115] RSP: 0018:ffff8880b7e0f1c0 EFLAGS: 00010247 [ 36.844756][ T1115] RAX: dffffc0000000000 RBX: ffff8880d14cca00 RCX: 1ffff11016fc1e99 [ 36.845859][ T1115] RDX: 0000000000000000 RSI: ffff8880c3d04000 RDI: 0000000000000004 [ 36.846961][ T1115] RBP: 0000000000000000 R08: ffff8880b7e0f8b0 R09: ffff8880b6ac2d90 [ 36.848020][ T1115] R10: ffffffffc0589a40 R11: ffffed1016d585b7 R12: ffffffff88ceaf80 [ 36.848788][ T1115] R13: ffff8880c3d04000 R14: ffff8880b7e0f8b0 R15: ffff8880c3d04000 [ 36.849546][ T1115] FS: 00007f50ab3360c0(0000) GS:ffff8880da000000(0000) knlGS:0000000000000000 [ 36.851784][ T1115] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 36.852422][ T1115] CR2: 000055871afe5ab0 CR3: 00000000ae246001 CR4: 00000000000606e0 [ 36.853181][ T1115] Call Trace: [ 36.853514][ T1115] __rtnl_newlink+0xbdb/0x1270 [ 36.853967][ T1115] ? lock_downgrade+0x6e0/0x6e0 [ 36.854420][ T1115] ? rtnl_link_unregister+0x220/0x220 [ 36.854936][ T1115] ? lock_acquire+0x164/0x3b0 [ 36.855376][ T1115] ? is_bpf_image_address+0xff/0x1d0 [ 36.855884][ T1115] ? rtnl_newlink+0x4c/0x90 [ 36.856304][ T1115] ? kernel_text_address+0x111/0x140 [ 36.856857][ T1115] ? __kernel_text_address+0xe/0x30 [ 36.857440][ T1115] ? unwind_get_return_address+0x5f/0xa0 [ 36.858063][ T1115] ? create_prof_cpu_mask+0x20/0x20 [ 36.858644][ T1115] ? arch_stack_walk+0x83/0xb0 [ 36.859171][ T1115] ? stack_trace_save+0x82/0xb0 [ 36.859710][ T1115] ? stack_trace_consume_entry+0x160/0x160 [ 36.860357][ T1115] ? deactivate_slab.isra.78+0x2c5/0x800 [ 36.860928][ T1115] ? kasan_unpoison_shadow+0x30/0x40 [ 36.861520][ T1115] ? kmem_cache_alloc_trace+0x135/0x350 [ 36.862125][ T1115] ? rtnl_newlink+0x4c/0x90 [ 36.864073][ T1115] rtnl_newlink+0x65/0x90 [ ... ] Fixes: ceed73a2 ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Linus Torvalds authored
Merge tag 'kbuild-fixes-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild fixes from Masahiro Yamada: - fix missed rebuild of DT schema check - add some phony targets to PHONY - fix comments and documents * tag 'kbuild-fixes-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: kbuild: get rid of trailing slash from subdir- example kbuild: add dt_binding_check to PHONY in a correct place kbuild: add dtbs_check to PHONY kbuild: remove unneeded semicolon at the end of cmd_dtb_check kbuild: fix DT binding schema rule to detect command line changes kbuild: remove wrong documentation about mandatory-y kbuild: add comment for V=2 mode
-
Russell King authored
Don't attempt to interpret the PHY specific status register unless the PHY is indicating that the resolution is valid. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
The current code causes problems when the unregistering netdevice could be different then the registering one. Since the check in mlx5_lag_netdev_event() does not allow any other network namespace anyway, fix this by registerting the lag notifier per init network namespace only. Fixes: d48834f9 ("mlx5: Use dev_net netdevice notifier registrations") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Tested-by: Aya Levin <ayal@mellanox.com> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hidLinus Torvalds authored
Pull HID subsystem fixes from Jiri Kosina: - syzkaller-reported error handling fixes in various drivers, from various people - increase of HID report buffer size to 8K, which is apparently needed by certain modern devices - a few new device-ID-specific fixes / quirks - battery charging status reporting fix in logitech-hidpp, from Filipe Laíns * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: HID: hid-bigbenff: fix race condition for scheduled work during removal HID: hid-bigbenff: call hid_hw_stop() in case of error HID: hid-bigbenff: fix general protection fault caused by double kfree HID: i2c-hid: add Trekstor Surfbook E11B to descriptor override HID: alps: Fix an error handling path in 'alps_input_configured()' HID: hiddev: Fix race in in hiddev_disconnect() HID: core: increase HID report buffer size to 8KiB HID: core: fix off-by-one memset in hid_report_raw_event() HID: apple: Add support for recent firmware on Magic Keyboards HID: ite: Only bind to keyboard USB interface on Acer SW5-012 keyboard dock HID: logitech-hidpp: BatteryVoltage: only read chargeStatus if extPower is active
-
Tobias Klauser authored
Follow the pattern used with other *_show_fdinfo functions and only define unix_show_fdinfo and set it in proto_ops if CONFIG_PROCFS is set. Fixes: 3c32da19 ("unix: Show number of pending scm files of receive queue in fdinfo") Signed-off-by: Tobias Klauser <tklauser@distanz.ch> Reviewed-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Luo bin says: ==================== hinic: BugFixes the bug fixed in patch #2 has been present since the first commit. the bugs fixed in patch #1 and patch #3 have been present since the following commits: patch #1: 352f58b0 ("net-next/hinic: Set Rxq irq to specific cpu for NUMA") patch #3: 421e9526 ("hinic: add rss support") ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Luo bin authored
should use real receive queue number to configure hw rss indirect table rather than maximal queue number Signed-off-by: Luo bin <luobin9@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Luo bin authored
a reserved field is used to signify prime physical function index in the latest firmware version, so we must assign a value to it correctly Signed-off-by: Luo bin <luobin9@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Luo bin authored
can not use a local variable as an input parameter of irq_set_affinity_hint Signed-off-by: Luo bin <luobin9@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.lwn.net/linuxLinus Torvalds authored
Pull documentation fixes from Jonathan Corbet: "A pair of docs-build fixes" * tag 'docs-5.6-fixes' of git://git.lwn.net/linux: docs: Fix empty parallelism argument docs: remove MPX from the x86 toc
-
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/auditLinus Torvalds authored
Pull audit fixes from Paul Moore: "Two fixes for problems found by syzbot: - Moving audit filter structure fields into a union caused some problems in the code which populates that filter structure. We keep the union (that idea is a good one), but we are fixing the code so that it doesn't needlessly set fields in the union and mess up the error handling. - The audit_receive_msg() function wasn't validating user input as well as it should in all cases, we add the necessary checks" * tag 'audit-pr-20200226' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit: audit: always check the netlink payload length in audit_receive_msg() audit: fix error handling in audit_data_to_entry()
-
Karsten Graul authored
In smc_ib_remove_dev() check if the provided ib device was actually initialized for SMC before. Reported-by: syzbot+84484ccebdd4e5451d91@syzkaller.appspotmail.com Fixes: a4cf0443 ("smc: introduce SMC as an IB-client") Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Aaro Koskinen authored
We cannot register the same netdev notifier multiple times when probing stmmac devices. Register the notifier only once in module init, and also make debugfs creation/deletion safe against simultaneous notifier call. Fixes: 481a7d15 ("stmmac: debugfs entry name is not be changed when udev rename device name.") Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Antoine Tenart authored
The firmware paths for the VSC8584 PHYs not not contain the leading 'microchip/' directory, as used in linux-firmware, resulting in an error when probing the driver. This patch fixes it. Fixes: a5afc167 ("net: phy: mscc: add support for VSC8584 PHY") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Paolo Abeni authored
syzbot noted that the master MPTCP socket lacks the icsk_sync_mss callback, and was able to trigger a null pointer dereference: BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD 8e171067 P4D 8e171067 PUD 93fa2067 PMD 0 Oops: 0010 [#1] PREEMPT SMP KASAN CPU: 0 PID: 8984 Comm: syz-executor066 Not tainted 5.6.0-rc2-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:0x0 Code: Bad RIP value. RSP: 0018:ffffc900020b7b80 EFLAGS: 00010246 RAX: 1ffff110124ba600 RBX: 0000000000000000 RCX: ffff88809fefa600 RDX: ffff8880994cdb18 RSI: 0000000000000000 RDI: ffff8880925d3140 RBP: ffffc900020b7bd8 R08: ffffffff870225be R09: fffffbfff140652a R10: fffffbfff140652a R11: 0000000000000000 R12: ffff8880925d35d0 R13: ffff8880925d3140 R14: dffffc0000000000 R15: 1ffff110124ba6ba FS: 0000000001a0b880(0000) GS:ffff8880aea00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 00000000a6d6f000 CR4: 00000000001406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: cipso_v4_sock_setattr+0x34b/0x470 net/ipv4/cipso_ipv4.c:1888 netlbl_sock_setattr+0x2a7/0x310 net/netlabel/netlabel_kapi.c:989 smack_netlabel security/smack/smack_lsm.c:2425 [inline] smack_inode_setsecurity+0x3da/0x4a0 security/smack/smack_lsm.c:2716 security_inode_setsecurity+0xb2/0x140 security/security.c:1364 __vfs_setxattr_noperm+0x16f/0x3e0 fs/xattr.c:197 vfs_setxattr fs/xattr.c:224 [inline] setxattr+0x335/0x430 fs/xattr.c:451 __do_sys_fsetxattr fs/xattr.c:506 [inline] __se_sys_fsetxattr+0x130/0x1b0 fs/xattr.c:495 __x64_sys_fsetxattr+0xbf/0xd0 fs/xattr.c:495 do_syscall_64+0xf7/0x1c0 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x440199 Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffcadc19e48 EFLAGS: 00000246 ORIG_RAX: 00000000000000be RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440199 RDX: 0000000020000200 RSI: 00000000200001c0 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 0000000000000003 R09: 00000000004002c8 R10: 0000000000000009 R11: 0000000000000246 R12: 0000000000401a20 R13: 0000000000401ab0 R14: 0000000000000000 R15: 0000000000000000 Modules linked in: CR2: 0000000000000000 Address the issue adding a dummy icsk_sync_mss callback. To properly sync the subflows mss and options list we need some additional infrastructure, which will land to net-next. Reported-by: syzbot+f4dfece964792d80b139@syzkaller.appspotmail.com Fixes: 2303f994 ("mptcp: Associate MPTCP context with TCP socket") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sudheesh Mavila authored
net: phy: corrected the return value for genphy_check_and_restart_aneg and genphy_c45_check_and_restart_aneg When auto-negotiation is not required, return value should be zero. Changes v1->v2: - improved comments and code as Andrew Lunn and Heiner Kallweit suggestion - fixed issue in genphy_c45_check_and_restart_aneg as Russell King suggestion. Fixes: 2a10ab04 ("net: phy: add genphy_check_and_restart_aneg()") Fixes: 1af9f168 ("net: phy: add genphy_c45_check_and_restart_aneg()") Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
-
yangerkun authored
As the description before netdev_run_todo, we cannot call free_netdev before rtnl_unlock, fix it by reorder the code. Signed-off-by: yangerkun <yangerkun@huawei.com> Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
IPV6_ADDRFORM is able to transform IPv6 socket to IPv4 one. While this operation sounds illogical, we have to support it. One of the things it does for TCP socket is to switch sk->sk_prot to tcp_prot. We now have other layers playing with sk->sk_prot, so we should make sure to not interfere with them. This patch makes sure sk_prot is the default pointer for TCP IPv6 socket. syzbot reported : BUG: kernel NULL pointer dereference, address: 0000000000000000 PGD a0113067 P4D a0113067 PUD a8771067 PMD 0 Oops: 0010 [#1] PREEMPT SMP KASAN CPU: 0 PID: 10686 Comm: syz-executor.0 Not tainted 5.6.0-rc2-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 RIP: 0010:0x0 Code: Bad RIP value. RSP: 0018:ffffc9000281fce0 EFLAGS: 00010246 RAX: 1ffffffff15f48ac RBX: ffffffff8afa4560 RCX: dffffc0000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8880a69a8f40 RBP: ffffc9000281fd10 R08: ffffffff86ed9b0c R09: ffffed1014d351f5 R10: ffffed1014d351f5 R11: 0000000000000000 R12: ffff8880920d3098 R13: 1ffff1101241a613 R14: ffff8880a69a8f40 R15: 0000000000000000 FS: 00007f2ae75db700(0000) GS:ffff8880aea00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 00000000a3b85000 CR4: 00000000001406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: inet_release+0x165/0x1c0 net/ipv4/af_inet.c:427 __sock_release net/socket.c:605 [inline] sock_close+0xe1/0x260 net/socket.c:1283 __fput+0x2e4/0x740 fs/file_table.c:280 ____fput+0x15/0x20 fs/file_table.c:313 task_work_run+0x176/0x1b0 kernel/task_work.c:113 tracehook_notify_resume include/linux/tracehook.h:188 [inline] exit_to_usermode_loop arch/x86/entry/common.c:164 [inline] prepare_exit_to_usermode+0x480/0x5b0 arch/x86/entry/common.c:195 syscall_return_slowpath+0x113/0x4a0 arch/x86/entry/common.c:278 do_syscall_64+0x11f/0x1c0 arch/x86/entry/common.c:304 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x45c429 Code: ad b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b6 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f2ae75dac78 EFLAGS: 00000246 ORIG_RAX: 0000000000000036 RAX: 0000000000000000 RBX: 00007f2ae75db6d4 RCX: 000000000045c429 RDX: 0000000000000001 RSI: 000000000000011a RDI: 0000000000000004 RBP: 000000000076bf20 R08: 0000000000000038 R09: 0000000000000000 R10: 0000000020000180 R11: 0000000000000246 R12: 00000000ffffffff R13: 0000000000000a9d R14: 00000000004ccfb4 R15: 000000000076bf2c Modules linked in: CR2: 0000000000000000 ---[ end trace 82567b5207e87bae ]--- RIP: 0010:0x0 Code: Bad RIP value. RSP: 0018:ffffc9000281fce0 EFLAGS: 00010246 RAX: 1ffffffff15f48ac RBX: ffffffff8afa4560 RCX: dffffc0000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8880a69a8f40 RBP: ffffc9000281fd10 R08: ffffffff86ed9b0c R09: ffffed1014d351f5 R10: ffffed1014d351f5 R11: 0000000000000000 R12: ffff8880920d3098 R13: 1ffff1101241a613 R14: ffff8880a69a8f40 R15: 0000000000000000 FS: 00007f2ae75db700(0000) GS:ffff8880aea00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 00000000a3b85000 CR4: 00000000001406f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Fixes: 604326b4 ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+1938db17e275e85dc328@syzkaller.appspotmail.com Cc: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ursula Braun authored
If an SMC connection to a certain peer is setup the first time, a new linkgroup is created. In case of setup failures, such a linkgroup is unusable and should disappear. As a first step the linkgroup is removed from the linkgroup list in smc_lgr_forget(). There are 2 problems: smc_listen_decline() might be called before linkgroup creation resulting in a crash due to calling smc_lgr_forget() with parameter NULL. If a setup failure occurs after linkgroup creation, the connection is never unregistered from the linkgroup, preventing linkgroup freeing. This patch introduces an enhanced smc_lgr_cleanup_early() function which * contains a linkgroup check for early smc_listen_decline() invocations * invokes smc_conn_free() to guarantee unregistering of the connection. * schedules fast linkgroup removal of the unusable linkgroup And the unused function smcd_conn_free() is removed from smc_core.h. Fixes: 3b2dec26 ("net/smc: restructure client and server code in af_smc") Fixes: 2a0674ff ("net/smc: improve abnormal termination of link groups") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Nicolas Saenz Julienne authored
Outdated Raspberry Pi 4 firmware might configure the external PHY as rgmii although the kernel currently sets it as rgmii-rxid. This makes connections unreliable as ID_MODE_DIS is left enabled. To avoid this, explicitly clear that bit whenever we don't need it. Fixes: da388022 ("net: bcmgenet: Add RGMII_RXID support") Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiri Pirko authored
The put of the flags was added by the commit referenced in fixes tag, however the size of the message was not extended accordingly. Fix this by adding size of the flags bitfield to the message size. Fixes: e3822678 ("net: sched: update action implementations to support flags") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Masahiro Yamada authored
obj-* needs a trailing slash for a directory, but subdir-* does not. Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
-
Madhuparna Bhowmik authored
list_for_each_entry_rcu() has built-in RCU and lock checking. Pass cond argument to list_for_each_entry_rcu() to silence false lockdep warning when CONFIG_PROVE_RCU_LIST is enabled. The devlink->lock is held when devlink_dpipe_table_find() is called in non RCU read side section. Therefore, pass struct devlink to devlink_dpipe_table_find() for lockdep checking. Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
We are still experiencing some packet loss with the existing advanced congestion buffering (ACB) settings with the IMP port configured for 2Gb/sec, so revert to conservative link speeds that do not produce packet loss until this is resolved. Fixes: 8f1880cb ("net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec") Fixes: de34d708 ("net: dsa: bcm_sf2: Only 7278 supports 2Gb/sec IMP port") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-