Since commit 6f888e7bc7bd58 ("clk: meson: clk-pll: add enable bit") our
PLLs also support the "enable" bit. Currently meson_clk_pll_enable
unconditionally resets the PLL, enables it, takes it out of reset and
waits until it is locked.

This works fine for our current clock trees. However, there will be a
problem once we allow modifications to sys_pll on Meson8, Meson8b and
Meson8m2 (which will be required for CPU frequency scaling):
the CPU clock is derived from the sys_pll clock. Once clk_enable is
called on the CPU clock this will be propagated by the common clock
framework up until the sys_pll clock. If we reset the PLL
unconditionally in meson_clk_pll_enable the CPU will be stopped (on
Meson8, Meson8b and Meson8m2).
To prevent this we simply check if the PLL is already enabled and do
reset the PLL if it's already enabled and locked.

Now that we have a utility function to check whether the PLL is enabled
we can also pass that to our clk_ops to let the common clock framework
know about the status of the hardware clock.
For now this is of limited use since the only common clock framework's
internal "disabled unused clocks" mechanism checks for this. Everything
else still uses the ref-counting (internal to the common clock
framework) when clk_enable is called.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181115224048.13511-2-martin.blumenstingl@googlemail.com

According to the public S805 datasheet HHI_SYS_CPU_CLK_CNTL1[29:20] is
the register for the CPU scale_div clock. This matches the code in
Amlogic's 3.10 GPL kernel sources:
N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;

This means that the divider register is 10 bit wide instead of 9 bits.
So far this is not a problem since all u-boot versions I have seen are
not using the cpu_scale_div clock at all (instead they are configuring
the CPU clock to run off cpu_in_sel directly).

The fixes tag points to the latest rework of the CPU clocks. However,
even before the rework it was wrong. Commit 7a29a869 ("clk: meson:
Add support for Meson clock controller") defines MESON_N_WIDTH as 9 (in
drivers/clk/meson/clk-cpu.c). But since the old clk-cpu implementation
this only carries the fixes tag for the CPU clock rewordk.

Fixes: 251b6fd3 ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20180927085921.24627-3-martin.blumenstingl@googlemail.com

The public S805 datasheet only mentions that
HHI_SYS_CPU_CLK_CNTL1[20:29] contains a divider called "cpu_scale_div".
Unfortunately it does not mention how to use the register contents.

The Amlogic 3.10 GPL kernel sources are using the following code to
calculate the CPU clock based on that register (taken from
arch/arm/mach-meson8/clock.c in the 3.10 Amlogic kernel, shortened to
make it easier to read):
N = (aml_read_reg32(P_HHI_SYS_CPU_CLK_CNTL1) >> 20) & 0x3FF;
if (sel == 3) /* use cpu_scale_div */
  div = 2 * N;
else
  div = ... /* not relevant for this example */
cpu_clk = parent_clk / div;

This suggests that the formula is: parent_rate / 2 * register_value
However, running perf (which can measure the CPU clock rate thanks to
the ARM PMU) shows that this formula is not correct.
This can be reproduced with the following steps:
1. boot into u-boot
2. let the CPU clock run off the XTAL clock:
   mw.l 0xC110419C 0x30 1
3. set the cpu_scale_div register:
   to value 0x1: mw.l 0xC110415C 0x801016A2 1
   to value 0x2: mw.l 0xC110415C 0x802016A2 1
   to value 0x5: mw.l 0xC110415C 0x805016A2 1
4. let the CPU clock run off cpu_scale_div:
   mw.l 0xC110419C 0xbd 1
5. boot Linux
6. run: perf stat -aB stress --cpu 4 --timeout 10
7. check the "cycles" value

I get the following results depending on the cpu_scale_div value:
- (cpu_in_sel - this is the input clock for cpu_scale_div - runs at
   1.2GHz)
- 0x1 = 300MHz
- 0x2 = 200MHz
- 0x5 = 100MHz

This means that the actual formula to calculate the output of the
cpu_scale_div clock is: parent_rate / 2 * (register value + 1).

The register value 0x0 is reserved. When letting the CPU clock run off
the cpu_scale_div while the value is 0x0 the whole board hangs (even in
u-boot).

I also verified this with the TWD timer: when adding this to the .dts
without specifying it's clock it will auto-detect the PERIPH (which is
the input clock of the TWD) clock rate (and the result is shown in the
kernel log). On Meson8, Meson8b and Meson8m2 the PERIPH clock is CPUCLK
divided by 4. This also matched for all three test-cases from above (in
all cases the TWD timer clock rate was approx. one fourth of the CPU
clock rate).

A small note regarding the "fixes" tag: the original issue seems to
exist virtually since forever. Even commit 28b9fcd0 ("clk:
meson8b: Add support for Meson8b clocks") seems to handle this wrong. I
still decided to use commit 251b6fd3 ("clk: meson: rework meson8b
cpu clock") because this is the first commit which gets the CPU hiearchy
correct and thus it's the first commit where the cpu_scale_div register
is used correctly (apart from the bug in the cpu_scale_table).

Fixes: 251b6fd3 ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20180927085921.24627-2-martin.blumenstingl@googlemail.com

The clock controller is located in a register range (called "HHI") which
contains more than just registers for the clock controller. Known
consumers of the HHI register range are:
- the clock controller
- a reset controller
- temperature sensor calibration coefficient (TSC) (only on Meson8b and
  Meson8m2)
- HDMI controller

The main reason for using a syscon is the "temperature sensor
calibration coefficient" which has to be set for the built-in temperature
sensor to work correctly. Four TSC bits are located in the SAR ADC's
register space. However on Meson8b and Meson8m2 there is a fifth TSC bit
which is unfortunately located in the HHI register space. To be more
precise, bit 9 of the HHI_DPLL_TOP_0 register (which sits right between
the HHI_SYS_PLL and HHI_VID_PLL registers).

Get the regmap from the parent (HHI syscon) node to support all
functionality of the HHI register range. Backwards compatibility with
old .dtbs is ensured by falling back to parsing the registers just like
before this change.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181028120859.5735-3-martin.blumenstingl@googlemail.com

The clock controller on Meson8/Meson8m2 and Meson8b is part of a
register region called "HHI". This register area contains more
functionality than just a clock controller:
- the clock controller
- some reset controller bits
- temperature sensor calibration coefficient (only on Meson8b and
  Meson8m2 - one one out of five TSC bits is stored in the HHI
  registers)
- HDMI controller

The HHI register area may be accessed concurrently. Allow this by using
a "system controller" as parent node.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181028120859.5735-2-martin.blumenstingl@googlemail.com

Add the clocks entries used in the video clock path, the clock path
is doubled to permit having different synchronized clocks for different
parts of the video pipeline.

All dividers are flagged with CLK_GET_RATE_NOCACHE, and all gates are flagged
with CLK_IGNORE_UNUSED since they are currently directly handled by the
Meson DRM Driver.
Once the DRM Driver is fully migrated to using the Common Clock Framework
to handle the video clock tree, the CLK_GET_RATE_NOCACHE and CLK_IGNORE_UNUSED
will be dropped.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: http://lkml.kernel.org/r/1541516257-16157-5-git-send-email-narmstrong@baylibre.com

Add the video clock bindings covering all the video graphics pipeline
and the HDMI controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: http://lkml.kernel.org/r/1541516257-16157-4-git-send-email-narmstrong@baylibre.com

In an attempt to better describe the HDMI PLL, a single DCO clock was
left for GXBB and GXL, but the GXL DCO does not have a pre-multiplier.

This patch adds back a GXL specific HDMI PLL DCO with xtal as parent.

Fixes: 87173557 ("clk: meson: clk-pll: remove od parameters")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: http://lkml.kernel.org/r/1541516257-16157-3-git-send-email-narmstrong@baylibre.com

Add support the VID_PLL fully programmable divider used right after the
HDMI PLL clock source. It is used to achieve complex fractional division
with a programmble bitfield.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: http://lkml.kernel.org/r/1541516257-16157-2-git-send-email-narmstrong@baylibre.com

There are four CPU clock post dividers:
- ABP
- PERIPH (used as input for the ARM global timer and ARM TWD timer)
- AXI
- L2 DRAM

Export these so we can use them in .dts files.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181122214017.25643-2-martin.blumenstingl@googlemail.com

Pull UBIFS updates from Richard Weinberger:

 - Full filesystem authentication feature, UBIFS is now able to have the
   whole filesystem structure authenticated plus user data encrypted and
   authenticated.

 - Minor cleanups

* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
  ubifs: Remove unneeded semicolon
  Documentation: ubifs: Add authentication whitepaper
  ubifs: Enable authentication support
  ubifs: Do not update inode size in-place in authenticated mode
  ubifs: Add hashes and HMACs to default filesystem
  ubifs: authentication: Authenticate super block node
  ubifs: Create hash for default LPT
  ubfis: authentication: Authenticate master node
  ubifs: authentication: Authenticate LPT
  ubifs: Authenticate replayed journal
  ubifs: Add auth nodes to garbage collector journal head
  ubifs: Add authentication nodes to journal
  ubifs: authentication: Add hashes to index nodes
  ubifs: Add hashes to the tree node cache
  ubifs: Create functions to embed a HMAC in a node
  ubifs: Add helper functions for authentication support
  ubifs: Add separate functions to init/crc a node
  ubifs: Format changes for authentication support
  ubifs: Store read superblock node
  ubifs: Drop write_node
  ...

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Bugfix:
   - Fix build issues on architectures that don't provide 64-bit cmpxchg

  Cleanups:
   - Fix a spelling mistake"

* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: fix spelling mistake, EACCESS -> EACCES
  SUNRPC: Use atomic(64)_t for seq_send(64)

Pull more timer updates from Thomas Gleixner:
 "A set of commits for the new C-SKY architecture timers"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings: timer: gx6605s SOC timer
  clocksource/drivers/c-sky: Add gx6605s SOC system timer
  dt-bindings: timer: C-SKY Multi-processor timer
  clocksource/drivers/c-sky: Add C-SKY SMP timer

Pull NTB updates from Jon Mason:
 "Fairly minor changes and bug fixes:

  NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
  private struct, and a few bug fixes"

* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
  ntb: idt: Alter the driver info comments
  ntb: idt: Discard temperature sensor IRQ handler
  ntb: idt: Add basic hwmon sysfs interface
  ntb: idt: Alter temperature read method
  ntb_netdev: Simplify remove with client device drvdata
  NTB: transport: Try harder to alloc an aligned MW buffer
  ntb: ntb_transport: Mark expected switch fall-throughs
  ntb: idt: Set PCIe bus address to BARLIMITx
  NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
  ntb: intel: fix return value for ndev_vec_mask()
  ntb_netdev: fix sleep time mismatch

Pull scheduler fixes from Ingo Molnar:
 "A memory (under-)allocation fix and a comment fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/topology: Fix off by one bug
  sched/rt: Update comment in pick_next_task_rt()

Pull x86 fixes from Ingo Molnar:
 "A number of fixes and some late updates:

   - make in_compat_syscall() behavior on x86-32 similar to other
     platforms, this touches a number of generic files but is not
     intended to impact non-x86 platforms.

   - objtool fixes

   - PAT preemption fix

   - paravirt fixes/cleanups

   - cpufeatures updates for new instructions

   - earlyprintk quirk

   - make microcode version in sysfs world-readable (it is already
     world-readable in procfs)

   - minor cleanups and fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  compat: Cleanup in_compat_syscall() callers
  x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
  objtool: Support GCC 9 cold subfunction naming scheme
  x86/numa_emulation: Fix uniform-split numa emulation
  x86/paravirt: Remove unused _paravirt_ident_32
  x86/mm/pat: Disable preemption around __flush_tlb_all()
  x86/paravirt: Remove GPL from pv_ops export
  x86/traps: Use format string with panic() call
  x86: Clean up 'sizeof x' => 'sizeof(x)'
  x86/cpufeatures: Enumerate MOVDIR64B instruction
  x86/cpufeatures: Enumerate MOVDIRI instruction
  x86/earlyprintk: Add a force option for pciserial device
  objtool: Support per-function rodata sections
  x86/microcode: Make revision and processor flags world-readable

Pull perf updates and fixes from Ingo Molnar:
 "These are almost all tooling updates: 'perf top', 'perf trace' and
  'perf script' fixes and updates, an UAPI header sync with the merge
  window versions, license marker updates, much improved Sparc support
  from David Miller, and a number of fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
  perf intel-pt/bts: Calculate cpumode for synthesized samples
  perf intel-pt: Insert callchain context into synthesized callchains
  perf tools: Don't clone maps from parent when synthesizing forks
  perf top: Start display thread earlier
  tools headers uapi: Update linux/if_link.h header copy
  tools headers uapi: Update linux/netlink.h header copy
  tools headers: Sync the various kvm.h header copies
  tools include uapi: Update linux/mmap.h copy
  perf trace beauty: Use the mmap flags table generated from headers
  perf beauty: Wire up the mmap flags table generator to the Makefile
  perf beauty: Add a generator for MAP_ mmap's flag constants
  tools include uapi: Update asound.h copy
  tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
  tools include uapi: Update linux/fs.h copy
  perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
  perf cs-etm: Correct CPU mode for samples
  perf unwind: Take pgoff into account when reporting elf to libdwfl
  perf top: Do not use overwrite mode by default
  perf top: Allow disabling the overwrite mode
  perf trace: Beautify mount's first pathname arg
  ...

Pull irq fixes from Ingo Molnar:
 "An irqchip driver fix and a memory (over-)allocation fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
  irq/matrix: Fix memory overallocation

With the addition of the NUMA identity level, we increased @level by
one and will run off the end of the array in the distance sort loop.

Fixed: 051f3ca0 ("sched/topology: Introduce NUMA identity node sched domain")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes who have come in near or during the merge window:

   - Removal of a VLA usage in Marvell mpp platform code

   - Enable some IPMI options for ARM64 servers by default, helps
     testing

   - Enable PREEMPT on 32-bit ARMv7 defconfig

   - Minor fix for stm32 DT (removal of an unused DMA property)

   - Bugfix for TI OMAP1-based ams-delta (-EINVAL -> IRQ_NOTCONNECTED)"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: stm32: update HASH1 dmas property on stm32mp157c
  ARM: orion: avoid VLA in orion_mpp_conf
  ARM: defconfig: Update multi_v7 to use PREEMPT
  arm64: defconfig: Enable some IPMI configs
  soc: ti: QMSS: Fix usage of irq_set_affinity_hint
  ARM: OMAP1: ams-delta: Fix impossible .irq < 0

Pull more arm64 updates from Catalin Marinas:

 - fix W+X page (mark RO) allocated by the arm64 kprobes code

 - Makefile fix for .i files in out of tree modules

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: kprobe: make page to RO mode when allocate it
  arm64: kdump: fix small typo
  arm64: makefile fix build of .i file in external module case

Pull dma-mapping fix from Christoph Hellwig:
 "Avoid compile warnings on non-default arm64 configs"

* tag 'dma-mapping-4.20-2' of git://git.infradead.org/users/hch/dma-mapping:
  arm64: fix warnings without CONFIG_IOMMU_DMA

Pull Kbuild updates from Masahiro Yamada:

 - clean-up leftovers in Kconfig files

 - remove stale oldnoconfig and silentoldconfig targets

 - remove unneeded cc-fullversion and cc-name variables

 - improve merge_config script to allow overriding option prefix

* tag 'kbuild-v4.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: remove cc-name variable
  kbuild: replace cc-name test with CONFIG_CC_IS_CLANG
  merge_config.sh: Allow to define config prefix
  kbuild: remove unused cc-fullversion variable
  kconfig: remove silentoldconfig target
  kconfig: remove oldnoconfig target
  powerpc: PCI_MSI needs PCI
  powerpc: remove CONFIG_MCA leftovers
  powerpc: remove CONFIG_PCI_QSPAN
  scsi: aha152x: rename the PCMCIA define

Pull cifs fixes and updates from Steve French:
 "Three small fixes (one Kerberos related, one for stable, and another
  fixes an oops in xfstest 377), two helpful debugging improvements,
  three patches for cifs directio and some minor cleanup"

* tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: fix signed/unsigned mismatch on aio_read patch
  cifs: don't dereference smb_file_target before null check
  CIFS: Add direct I/O functions to file_operations
  CIFS: Add support for direct I/O write
  CIFS: Add support for direct I/O read
  smb3: missing defines and structs for reparse point handling
  smb3: allow more detailed protocol info on open files for debugging
  smb3: on kerberos mount if server doesn't specify auth type use krb5
  smb3: add trace point for tree connection
  cifs: fix spelling mistake, EACCESS -> EACCES
  cifs: fix return value for cifs_listxattr

Pull 9p fix from Al Viro:
 "Regression fix for net/9p handling of iov_iter; broken by braino when
  switching to iov_iter_is_kvec() et.al., spotted and fixed by Marc"

* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  iov_iter: Fix 9p virtio breakage

Pull more SCSI updates from James Bottomley:
 "This is a set of minor small (and safe changes) that didn't make the
  initial pull request plus some bug fixes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: mvsas: Remove set but not used variable 'id'
  scsi: qla2xxx: Remove two arguments from qlafx00_error_entry()
  scsi: qla2xxx: Make sure that qlafx00_ioctl_iosb_entry() initializes 'res'
  scsi: qla2xxx: Remove a set-but-not-used variable
  scsi: qla2xxx: Make qla2x00_sysfs_write_nvram() easier to analyze
  scsi: qla2xxx: Declare local functions 'static'
  scsi: qla2xxx: Improve several kernel-doc headers
  scsi: qla2xxx: Modify fall-through annotations
  scsi: 3w-sas: 3w-9xxx: Use unsigned char for cdb
  scsi: mvsas: Use dma_pool_zalloc
  scsi: target: Don't request modules that aren't even built
  scsi: target: Set response length for REPORT TARGET PORT GROUPS

Merge more updates from Andrew Morton:

 - more ocfs2 work

 - various leftovers

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  memory_hotplug: cond_resched in __remove_pages
  bfs: add sanity check at bfs_fill_super()
  kernel/sysctl.c: remove duplicated include
  kernel/kexec_file.c: remove some duplicated includes
  mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask
  ocfs2: fix clusters leak in ocfs2_defrag_extent()
  ocfs2: dlmglue: clean up timestamp handling
  ocfs2: don't put and assigning null to bh allocated outside
  ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
  ocfs2: don't use iocb when EIOCBQUEUED returns
  ocfs2: without quota support, avoid calling quota recovery
  ocfs2: remove ocfs2_is_o2cb_active()
  mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
  include/linux/notifier.h: SRCU: fix ctags
  mm: handle no memcg case in memcg_kmem_charge() properly

We have received a bug report that unbinding a large pmem (>1TB) can
result in a soft lockup:

  NMI watchdog: BUG: soft lockup - CPU#9 stuck for 23s! [ndctl:4365]
  [...]
  Supported: Yes
  CPU: 9 PID: 4365 Comm: ndctl Not tainted 4.12.14-94.40-default #1 SLE12-SP4
  Hardware name: Intel Corporation S2600WFD/S2600WFD, BIOS SE5C620.86B.01.00.0833.051120182255 05/11/2018
  task: ffff9cce7d4410c0 task.stack: ffffbe9eb1bc4000
  RIP: 0010:__put_page+0x62/0x80
  Call Trace:
   devm_memremap_pages_release+0x152/0x260
   release_nodes+0x18d/0x1d0
   device_release_driver_internal+0x160/0x210
   unbind_store+0xb3/0xe0
   kernfs_fop_write+0x102/0x180
   __vfs_write+0x26/0x150
   vfs_write+0xad/0x1a0
   SyS_write+0x42/0x90
   do_syscall_64+0x74/0x150
   entry_SYSCALL_64_after_hwframe+0x3d/0xa2
  RIP: 0033:0x7fd13166b3d0

It has been reported on an older (4.12) kernel but the current upstream
code doesn't cond_resched in the hot remove code at all and the given
range to remove might be really large.  Fix the issue by calling
cond_resched once per memory section.

Link: http://lkml.kernel.org/r/20181031125840.23982-1-mhocko@kernel.orgSigned-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

syzbot is reporting too large memory allocation at bfs_fill_super() [1].
Since file system image is corrupted such that bfs_sb->s_start == 0,
bfs_fill_super() is trying to allocate 8MB of continuous memory. Fix
this by adding a sanity check on bfs_sb->s_start, __GFP_NOWARN and
printf().

[1] https://syzkaller.appspot.com/bug?id=16a87c236b951351374a84c8a32f40edbc034e96

Link: http://lkml.kernel.org/r/1525862104-3407-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jpSigned-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+71c6b5d68e91149fc8a4@syzkaller.appspotmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Tigran Aivazian <aivazian.tigran@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove one include of <linux/pipe_fs_i.h>.
No functional changes.

Link: http://lkml.kernel.org/r/20181004134223.17735-1-michael@schupikov.deSigned-off-by: Michael Schupikov <michael@schupikov.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We include kexec.h and slab.h twice in kexec_file.c. It's unnecessary.
hence just remove them.

Link: http://lkml.kernel.org/r/1537498098-19171-1-git-send-email-zhongjiang@huawei.comSigned-off-by: zhong jiang <zhongjiang@huawei.com>
Reviewed-by: Bhupesh Sharma <bhsharma@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

THP allocation mode is quite complex and it depends on the defrag mode.
This complexity is hidden in alloc_hugepage_direct_gfpmask from a large
part currently. The NUMA special casing (namely __GFP_THISNODE) is
however independent and placed in alloc_pages_vma currently. This both
adds an unnecessary branch to all vma based page allocation requests and
it makes the code more complex unnecessarily as well. Not to mention
that e.g. shmem THP used to do the node reclaiming unconditionally
regardless of the defrag mode until recently. This was not only
unexpected behavior but it was also hardly a good default behavior and I
strongly suspect it was just a side effect of the code sharing more than
a deliberate decision which suggests that such a layering is wrong.

Get rid of the thp special casing from alloc_pages_vma and move the
logic to alloc_hugepage_direct_gfpmask. __GFP_THISNODE is applied to the
resulting gfp mask only when the direct reclaim is not requested and
when there is no explicit numa binding to preserve the current logic.

Please note that there's also a slight difference wrt MPOL_BIND now. The
previous code would avoid using __GFP_THISNODE if the local node was
outside of policy_nodemask(). After this patch __GFP_THISNODE is avoided
for all MPOL_BIND policies. So there's a difference that if local node
is actually allowed by the bind policy's nodemask, previously
__GFP_THISNODE would be added, but now it won't be. From the behavior
POV this is still correct because the policy nodemask is used.

Link: http://lkml.kernel.org/r/20180925120326.24392-3-mhocko@kernel.orgSigned-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Cc: Zi Yan <zi.yan@cs.rutgers.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ocfs2_defrag_extent() might leak allocated clusters.  When the file
system has insufficient space, the number of claimed clusters might be
less than the caller wants.  If that happens, the original code might
directly commit the transaction without returning clusters.

This patch is based on code in ocfs2_add_clusters_in_btree().

[akpm@linux-foundation.org: include localalloc.h, reduce scope of data_ac]
Link: http://lkml.kernel.org/r/20180904041621.16874-3-lchen@suse.comSigned-off-by: Larry Chen <lchen@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Changwei Ge <ge.changwei@h3c.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The handling of timestamps outside of the 1970..2038 range in the dlm
glue is rather inconsistent: on 32-bit architectures, this has always
wrapped around to negative timestamps in the 1902..1969 range, while on
64-bit kernels all timestamps are interpreted as positive 34 bit numbers
in the 1970..2514 year range.

Now that the VFS code handles 64-bit timestamps on all architectures, we
can make the behavior more consistent here, and return the same result
that we had on 64-bit already, making the file system y2038 safe in the
process.  Outside of dlmglue, it already uses 64-bit on-disk timestamps
anway, so that part is fine.

For consistency, I'm changing ocfs2_pack_timespec() to clamp anything
outside of the supported range to the minimum and maximum values.  This
avoids a possible ambiguity of values before 1970 in particular, which
used to be interpreted as times at the end of the 2514 range previously.

Link: http://lkml.kernel.org/r/20180619155826.4106487-1-arnd@arndb.deSigned-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Changwei Ge <ge.changwei@h3c.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

ocfs2_read_blocks() and ocfs2_read_blocks_sync() are both used to read
several blocks from disk.  Currently, the input argument *bhs* can be
NULL or NOT.  It depends on the caller's behavior.  If the function
fails in reading blocks from disk, the corresponding bh will be assigned
to NULL and put.

Obviously, above process for non-NULL input bh is not appropriate.
Because the caller doesn't even know its bhs are put and re-assigned.

If buffer head is managed by caller, ocfs2_read_blocks and
ocfs2_read_blocks_sync() should not evaluate it to NULL.  It will cause
caller accessing illegal memory, thus crash.

Link: http://lkml.kernel.org/r/HK2PR06MB045285E0F4FBB561F9F2F9B3D5680@HK2PR06MB0452.apcprd06.prod.outlook.comSigned-off-by: Changwei Ge <ge.changwei@h3c.com>
Reviewed-by: Guozhonghua <guozhonghua@h3c.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Changwei Ge <ge.changwei@h3c.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Somehow, file system metadata was corrupted, which causes
ocfs2_check_dir_entry() to fail in function ocfs2_dir_foreach_blk_el().

According to the original design intention, if above happens we should
skip the problematic block and continue to retrieve dir entry.  But
there is obviouse misuse of brelse around related code.

After failure of ocfs2_check_dir_entry(), current code just moves to
next position and uses the problematic buffer head again and again
during which the problematic buffer head is released for multiple times.
I suppose, this a serious issue which is long-lived in ocfs2.  This may
cause other file systems which is also used in a the same host insane.

So we should also consider about bakcporting this patch into linux
-stable.

Link: http://lkml.kernel.org/r/HK2PR06MB045211675B43EED794E597B6D56E0@HK2PR06MB0452.apcprd06.prod.outlook.comSigned-off-by: Changwei Ge <ge.changwei@h3c.com>
Suggested-by: Changkuo Shi <shi.changkuo@h3c.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When -EIOCBQUEUED returns, it means that aio_complete() will be called
from dio_complete(), which is an asynchronous progress against
write_iter.  Generally, IO is a very slow progress than executing
instruction, but we still can't take the risk to access a freed iocb.

And we do face a BUG crash issue.  Using the crash tool, iocb is
obviously freed already.

  crash> struct -x kiocb ffff881a350f5900
  struct kiocb {
    ki_filp = 0xffff881a350f5a80,
    ki_pos = 0x0,
    ki_complete = 0x0,
    private = 0x0,
    ki_flags = 0x0
  }

And the backtrace shows:
  ocfs2_file_write_iter+0xcaa/0xd00 [ocfs2]
  aio_run_iocb+0x229/0x2f0
  do_io_submit+0x291/0x540
  SyS_io_submit+0x10/0x20
  system_call_fastpath+0x16/0x75

Link: http://lkml.kernel.org/r/1523361653-14439-1-git-send-email-ge.changwei@h3c.comSigned-off-by: Changwei Ge <ge.changwei@h3c.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

During one dead node's recovery by other node, quota recovery work will
be queued.  We should avoid calling quota when it is not supported, so
check the quota flags.

Link: http://lkml.kernel.org/r/71604351584F6A4EBAE558C676F37CA401071AC9FB@H3CMLB12-EX.srv.huawei-3com.comSigned-off-by: guozhonghua <guozhonghua@h3c.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Joseph Qi <jiangqi903@gmail.com>
Cc: Changwei Ge <ge.changwei@h3c.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>