commit a6fe5e52 upstream.

pm_runtime_get_sync() and pm_runtime_put_autosuspend() return 0 on
success, 1 if the device's runtime PM status was already requested status
or error code on failure.  So a positive return value doesn't indicate an
error condition.

However, any non-zero return values from buffer preenable and postdisable
callbacks are recognized as an error and this driver reuses the return
value from pm_runtime_get_sync() and pm_runtime_put_autosuspend() in
these callbacks.  This change fixes the false error detections.

Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 73e3e3fc upstream.

This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously.  So this driver
doesn't insert a wait time before reading the conversion register if the
configuration is not changed from a previous request.

This assumption is broken if the device is runtime suspended and entered
a power-down state.  The forthcoming request causes reading a stale result
from the conversion register as the device is runtime resumed just before.

Fix it by adding a flag to detect that condition and insert a necessary
wait time.

Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e8245c68 upstream.

The ADS1015 device have two operating modes, continuous conversion mode
and single-shot mode.  This driver assumes that the continuous conversion
mode is selected by runtime resume callback when the ADC result is
requested.

If CONFIG_PM is disabled, the device is always in the default single-shot
mode and no one begins a single conversion.  So the conversion register
doesn't contain valid ADC result.  Fix it by changing the continuous mode
in probe function.

Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8d0e8e79 upstream.

The ti-ads1015 driver supports ADS1015 and ADS1115 devices.  The same
scale information is used for both devices in this driver, however they
have actually different values and the ADS1115's one is not correct.

These devices have the same full-scale input voltage range for each PGA
selection.  So instead of adding another hardcoded scale information,
compute a correct scale on demand from each device's resolution.

Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0d106b74 upstream.

The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own sampling frequency information.

The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings.  So the driver
should load the correct settings when the input multiplexer selection is
changed.

However, regardless of which channlel is currently selected, changing any
iio channel's sampling frequency information immediately overwrites the
current data rate setting in the config register.

It breaks the current data rate setting if the different channel's sampling
frequency information is changed because the data rate setting is not
reloaded when the input multiplexer is switched.

This removes the unexpected config register update and correctly load the
data rate setting before getting adc result.

Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 11b86a84 upstream.

Fix the values of DPAA2_FD_CTRL_FSE and DPAA2_FD_CTRL_FAERR,
which are shifted off by one bit.

Fixes: 39163c0c ("staging: fsl-dpaa2/eth: Errors checking update")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 737aed94 upstream.

The crypto API requires saving the last blocks of ciphertext
in req->info for use as IV for CTS mode. The ccree driver
was not doing this. This patch fixes that.

The bug was manifested with cts(cbc(aes)) mode in tcrypt tests.

Fixes: 302ef8eb ("Add CryptoCell skcipher support")
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 34ff1bf4 upstream.

The mask of sns_key_info1 suggests the upper nybble is being extracted
however the following shift of 8 bits is too large and always results in
0.  Fix this by shifting only by 4 bits to correctly get the upper nybble.

Detected by CoverityScan, CID#142891 ("Operands don't affect result")

Fixes: fa590c22 ("staging: rts5208: add support for rts5208 and rts5288")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ed62ca2f upstream.

While running reboot tests w/ a specific set of USB devices (and
slub_debug enabled), I found that once every few hours my device would
be crashed with a stack that looked like this:

[   14.012445] BUG: spinlock bad magic on CPU#0, modprobe/2091
[   14.012460]  lock: 0xffffffc0cb055978, .magic: ffffffc0, .owner: cryption contexts: %lu/%lu
[   14.012460] /1025536097, .owner_cpu: 0
[   14.012466] CPU: 0 PID: 2091 Comm: modprobe Not tainted 4.4.79 #352
[   14.012468] Hardware name: Google Kevin (DT)
[   14.012471] Call trace:
[   14.012483] [<....>] dump_backtrace+0x0/0x160
[   14.012487] [<....>] show_stack+0x20/0x28
[   14.012494] [<....>] dump_stack+0xb4/0xf0
[   14.012500] [<....>] spin_dump+0x8c/0x98
[   14.012504] [<....>] spin_bug+0x30/0x3c
[   14.012508] [<....>] do_raw_spin_lock+0x40/0x164
[   14.012515] [<....>] _raw_spin_lock_irqsave+0x64/0x74
[   14.012521] [<....>] __wake_up+0x2c/0x60
[   14.012528] [<....>] async_completed+0x2d0/0x300
[   14.012534] [<....>] __usb_hcd_giveback_urb+0xc4/0x138
[   14.012538] [<....>] usb_hcd_giveback_urb+0x54/0xf0
[   14.012544] [<....>] xhci_irq+0x1314/0x1348
[   14.012548] [<....>] usb_hcd_irq+0x40/0x50
[   14.012553] [<....>] handle_irq_event_percpu+0x1b4/0x3f0
[   14.012556] [<....>] handle_irq_event+0x4c/0x7c
[   14.012561] [<....>] handle_fasteoi_irq+0x158/0x1c8
[   14.012564] [<....>] generic_handle_irq+0x30/0x44
[   14.012568] [<....>] __handle_domain_irq+0x90/0xbc
[   14.012572] [<....>] gic_handle_irq+0xcc/0x18c

Investigation using kgdb() found that the wait queue that was passed
into wake_up() had been freed (it was filled with slub_debug poison).

I analyzed and instrumented the code and reproduced.  My current
belief is that this is happening:

1. async_completed() is called (from IRQ).  Moves "as" onto the
   completed list.
2. On another CPU, proc_reapurbnonblock_compat() calls
   async_getcompleted().  Blocks on spinlock.
3. async_completed() releases the lock; keeps running; gets blocked
   midway through wake_up().
4. proc_reapurbnonblock_compat() => async_getcompleted() gets the
   lock; removes "as" from completed list and frees it.
5. usbdev_release() is called.  Frees "ps".
6. async_completed() finally continues running wake_up().  ...but
   wake_up() has a pointer to the freed "ps".

The instrumentation that led me to believe this was based on adding
some trace_printk() calls in a select few functions and then using
kdb's "ftdump" at crash time.  The trace follows (NOTE: in the trace
below I cheated a little bit and added a udelay(1000) in
async_completed() after releasing the spinlock because I wanted it to
trigger quicker):

<...>-2104   0d.h2 13759034us!: async_completed at start: as=ffffffc0cc638200
mtpd-2055    3.... 13759356us : async_getcompleted before spin_lock_irqsave
mtpd-2055    3d..1 13759362us : async_getcompleted after list_del_init: as=ffffffc0cc638200
mtpd-2055    3.... 13759371us+: proc_reapurbnonblock_compat: free_async(ffffffc0cc638200)
mtpd-2055    3.... 13759422us+: async_getcompleted before spin_lock_irqsave
mtpd-2055    3.... 13759479us : usbdev_release at start: ps=ffffffc0cc042080
mtpd-2055    3.... 13759487us : async_getcompleted before spin_lock_irqsave
mtpd-2055    3.... 13759497us!: usbdev_release after kfree(ps): ps=ffffffc0cc042080
<...>-2104   0d.h2 13760294us : async_completed before wake_up(): as=ffffffc0cc638200

To fix this problem we can just move the wake_up() under the ps->lock.
There should be no issues there that I'm aware of.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9e18d0c8 upstream.

These will be required going forward.
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5cdcf4c6 upstream.

binder_fd_array_object starts with a 4-byte header,
followed by a few fields that are 8 bytes when
ANDROID_BINDER_IPC_32BIT=N.

This can cause alignment issues in a 64-bit kernel
with a 32-bit userspace, as on x86_32 an 8-byte primitive
may be aligned to a 4-byte address. Pad with a __u32
to fix this.
Signed-off-by: Martijn Coenen <maco@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 082df8be upstream.

Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:

  Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
  ...
  [<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
  [<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
  [<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)

This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)

This is a regression that was introduced by commit 1c4d0b4e ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:

Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.

Commit a1fc1920 ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f95 ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:

  musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
    musb-hdrc.0 but parent (47401400.usb) is not active

This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).

Fixes: c338412b ("usb: musb: unconditionally save and restore the context on suspend")
Fixes: a1fc1920 ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume")
Fixes: 1c4d0b4e ("usb: musb: Remove pm_runtime_set_irq_safe")
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e6b422b8 upstream.

The following commit cause a regression on ATI chipsets.
'commit e788787e ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'

This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.

Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: e788787e ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a1279ef7 upstream.

Commit e0429362
("usb: Add device quirk for Logitech HD Pro Webcams C920 and C930e")
introduced quirk to workaround an issue with some Logitech webcams.

Apparently model C920-C has the same issue so applying
the same quirk as well.

See aforementioned commit message for detailed explanation of the problem.
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 169e8654 upstream.

This commit adds support (an ID, really) for D-Link DWM-157 hardware
version C1 USB modem to option driver.

According to manufacturer-provided Windows INF file the device has four
serial ports:
"D-Link HSPA+DataCard Diagnostics Interface" (interface 2; modem port),
"D-Link HSPA+DataCard NMEA Device" (interface 3),
"D-Link HSPA+DataCard Speech Port" (interface 4),
"D-Link HSPA+DataCard Debug Port" (interface 5).

usb-devices output:
T:  Bus=05 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2001 ProdID=7d0e Rev=03.00
S:  Manufacturer=D-Link,Inc
S:  Product=D-Link DWM-157
C:  #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=02 Prot=01 Driver=option
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 6 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit de3af5bf upstream.

Corsair Strafe RGB keyboard has trouble to initialize:

[ 1.679455] usb 3-6: new full-speed USB device number 4 using xhci_hcd
[ 6.871136] usb 3-6: unable to read config index 0 descriptor/all
[ 6.871138] usb 3-6: can't read configurations, error -110
[ 6.991019] usb 3-6: new full-speed USB device number 5 using xhci_hcd
[ 12.246642] usb 3-6: unable to read config index 0 descriptor/all
[ 12.246644] usb 3-6: can't read configurations, error -110
[ 12.366555] usb 3-6: new full-speed USB device number 6 using xhci_hcd
[ 17.622145] usb 3-6: unable to read config index 0 descriptor/all
[ 17.622147] usb 3-6: can't read configurations, error -110
[ 17.742093] usb 3-6: new full-speed USB device number 7 using xhci_hcd
[ 22.997715] usb 3-6: unable to read config index 0 descriptor/all
[ 22.997716] usb 3-6: can't read configurations, error -110

Although it may work after several times unpluging/pluging:

[ 68.195240] usb 3-6: new full-speed USB device number 11 using xhci_hcd
[ 68.337459] usb 3-6: New USB device found, idVendor=1b1c, idProduct=1b20
[ 68.337463] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 68.337466] usb 3-6: Product: Corsair STRAFE RGB Gaming Keyboard
[ 68.337468] usb 3-6: Manufacturer: Corsair
[ 68.337470] usb 3-6: SerialNumber: 0F013021AEB8046755A93ED3F5001941

Tried three quirks: USB_QUIRK_DELAY_INIT, USB_QUIRK_NO_LPM and
USB_QUIRK_DEVICE_QUALIFIER, user confirmed that USB_QUIRK_DELAY_INIT alone
can workaround this issue. Hence add the quirk for Corsair Strafe RGB.

BugLink: https://bugs.launchpad.net/bugs/1678477Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull MIPS fixes from Ralf Baechle:
 "The two indirect syscall fixes have sat in linux-next for a few days.
  I did check back with a hardware designer to ensure a SYNC is really
  what's required for the GIC fix and so the GIC fix didn't make it into
  to linux-next in time for this final pull request.

  It builds in local build tests and passes Imagination's test system"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  irqchip: mips-gic: SYNC after enabling GIC region
  MIPS: Remove pt_regs adjustments in indirect syscall handler
  MIPS: seccomp: Fix indirect syscall args

Pull x86 fixes from Thomas Gleixner:

 - Expand the space for uncompressing as the LZ4 worst case does not fit
   into the currently reserved space

 - Validate boot parameters more strictly to prevent out of bound access
   in the decompressor/boot code

 - Fix off by one errors in get_segment_base()

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot: Prevent faulty bootparams.screeninfo from causing harm
  x86/boot: Provide more slack space during decompression
  x86/ldt: Fix off by one in get_segment_base()

Pull timer fix from Thomas Gleixner:
 "A single fix for a thinko in the raw timekeeper update which causes
  clock MONOTONIC_RAW to run with erratically increased frequency"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  time: Fix ktime_get_raw() incorrect base accumulation

Pull perf fixes from Thomas Gleixner:

 - Prevent a potential inconistency in the perf user space access which
   might lead to evading sanity checks.

 - Prevent perf recording function trace entries twice

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/ftrace: Fix double traces of perf on ftrace:function
  perf/core: Fix potential double-fetch bug

Pull cifs version warning fix from Steve French:
 "As requested, additional kernel warning messages to clarify the
  default dialect changes"

[ There is still some discussion about exactly which version should be
  the new default.  Longer-term we have auto-negotiation coming, but
  that's not there yet..  - Linus ]

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  Fix warning messages when mounting to older servers

Pull ARM SoC fixes from Olof Johansson:
 "A couple of late-arriving fixes before final 4.13:

   - A few reverts of DT bindings on Allwinner for their ethernet
     driver. Discussion didn't converge, and since bindings are
     considered ABI it makes sense to revert instead of having to
     support two bindings long-term.

   - A fix to enumerate GPIOs properly on Marvell Armada AP806"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dts: marvell: fix number of GPIOs in Armada AP806 description
  arm: dts: sunxi: Revert EMAC changes
  arm64: dts: allwinner: Revert EMAC changes
  dt-bindings: net: Revert sun8i dwmac binding

mvebu fixes for 4.13 (part 3)

Fix number of GPIOs in AP806 description for Armada 7K/8K

* tag 'mvebu-fixes-4.13-3' of git://git.infradead.org/linux-mvebu:
  arm64: dts: marvell: fix number of GPIOs in Armada AP806 description
Signed-off-by: Olof Johansson <olof@lixom.net>

Pull i2c fixes from Wolfram Sang:
 "The ismt driver had a problem with a rarely used transaction type and
  the designware driver was made even more robust against non standard
  ACPI tables"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: designware: Round down ACPI provided clk to nearest supported clk
  i2c: ismt: Return EMSGSIZE for block reads with bogus length
  i2c: ismt: Don't duplicate the receive length for block reads

The race was introduced by me in commit 971316f0 ("epoll:
ep_unregister_pollwait() can use the freed pwq->whead").  I did not
realize that nothing can protect eventpoll after ep_poll_callback() sets
->whead = NULL, only whead->lock can save us from the race with
ep_free() or ep_remove().

Move ->whead = NULL to the end of ep_poll_callback() and add the
necessary barriers.

TODO: cleanup the ewake/EPOLLEXCLUSIVE logic, it was confusing even
before this patch.

Hopefully this explains use-after-free reported by syzcaller:

	BUG: KASAN: use-after-free in debug_spin_lock_before
	...
	 _raw_spin_lock_irqsave+0x4a/0x60 kernel/locking/spinlock.c:159
	 ep_poll_callback+0x29f/0xff0 fs/eventpoll.c:1148

this is spin_lock(eventpoll->lock),

	...
	Freed by task 17774:
	...
	 kfree+0xe8/0x2c0 mm/slub.c:3883
	 ep_free+0x22c/0x2a0 fs/eventpoll.c:865

Fixes: 971316f0 ("epoll: ep_unregister_pollwait() can use the freed pwq->whead")
Reported-by: 范龙飞 <long7573@126.com>
Cc: stable@vger.kernel.org
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) Fix handling of pinned BPF map nodes in hash of maps, from Daniel
    Borkmann.

 2) IPSEC ESP error paths leak memory, from Steffen Klassert.

 3) We need an RCU grace period before freeing fib6_node objects, from
    Wei Wang.

 4) Must check skb_put_padto() return value in HSR driver, from FLorian
    Fainelli.

 5) Fix oops on PHY probe failure in ftgmac100 driver, from Andrew
    Jeffery.

 6) Fix infinite loop in UDP queue when using SO_PEEK_OFF, from Eric
    Dumazet.

 7) Use after free when tcf_chain_destroy() called multiple times, from
    Jiri Pirko.

 8) Fix KSZ DSA tag layer multiple free of SKBS, from Florian Fainelli.

 9) Fix leak of uninitialized memory in sctp_get_sctp_info(),
    inet_diag_msg_sctpladdrs_fill() and inet_diag_msg_sctpaddrs_fill().
    From Stefano Brivio.

10) L2TP tunnel refcount fixes from Guillaume Nault.

11) Don't leak UDP secpath in udp_set_dev_scratch(), from Yossi
    Kauperman.

12) Revert a PHY layer change wrt. handling of PHY_HALTED state in
    phy_stop_machine(), it causes regressions for multiple people. From
    Florian Fainelli.

13) When packets are sent out of br0 we have to clear the
    offload_fwdq_mark value.

14) Several NULL pointer deref fixes in packet schedulers when their
    ->init() routine fails. From Nikolay Aleksandrov.

15) Aquantium devices cannot checksum offload correctly when the packet
    is <= 60 bytes. From Pavel Belous.

16) Fix vnet header access past end of buffer in AF_PACKET, from
    Benjamin Poirier.

17) Double free in probe error paths of nfp driver, from Dan Carpenter.

18) QOS capability not checked properly in DCB init paths of mlx5
    driver, from Huy Nguyen.

19) Fix conflicts between firmware load failure and health_care timer in
    mlx5, also from Huy Nguyen.

20) Fix dangling page pointer when DMA mapping errors occur in mlx5,
    from Eran Ben ELisha.

21) ->ndo_setup_tc() in bnxt_en driver doesn't count rings properly,
    from Michael Chan.

22) Missing MSIX vector free in bnxt_en, also from Michael Chan.

23) Refcount leak in xfrm layer when using sk_policy, from Lorenzo
    Colitti.

24) Fix copy of uninitialized data in qlge driver, from Arnd Bergmann.

25) bpf_setsockopts() erroneously always returns -EINVAL even on
    success. Fix from Yuchung Cheng.

26) tipc_rcv() needs to linearize the SKB before parsing the inner
    headers, from Parthasarathy Bhuvaragan.

27) Fix deadlock between link status updates and link removal in netvsc
    driver, from Stephen Hemminger.

28) Missed locking of page fragment handling in ESP output, from Steffen
    Klassert.

29) Fix refcnt leak in ebpf congestion control code, from Sabrina
    Dubroca.

30) sxgbe_probe_config_dt() doesn't check devm_kzalloc()'s return value,
    from Christophe Jaillet.

31) Fix missing ipv6 rx_dst_cookie update when rx_dst is updated during
    early demux, from Paolo Abeni.

32) Several info leaks in xfrm_user layer, from Mathias Krause.

33) Fix out of bounds read in cxgb4 driver, from Stefano Brivio.

34) Properly propagate obsolete state of route upwards in ipv6 so that
    upper holders like xfrm can see it. From Xin Long.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (118 commits)
  udp: fix secpath leak
  bridge: switchdev: Clear forward mark when transmitting packet
  mlxsw: spectrum: Forbid linking to devices that have uppers
  wl1251: add a missing spin_lock_init()
  Revert "net: phy: Correctly process PHY_HALTED in phy_stop_machine()"
  net: dsa: bcm_sf2: Fix number of CFP entries for BCM7278
  kcm: do not attach PF_KCM sockets to avoid deadlock
  sch_tbf: fix two null pointer dereferences on init failure
  sch_sfq: fix null pointer dereference on init failure
  sch_netem: avoid null pointer deref on init failure
  sch_fq_codel: avoid double free on init failure
  sch_cbq: fix null pointer dereferences on init failure
  sch_hfsc: fix null pointer deref and double free on init failure
  sch_hhf: fix null pointer dereference on init failure
  sch_multiq: fix double free on init failure
  sch_htb: fix crash on init failure
  net/mlx5e: Fix CQ moderation mode not set properly
  net/mlx5e: Fix inline header size for small packets
  net/mlx5: E-Switch, Unload the representors in the correct order
  net/mlx5e: Properly resolve TC offloaded ipv6 vxlan tunnel source address
  ...

Pull ceph fix from Ilya Dryomov:
 "ceph fscache page locking fix from Zheng, marked for stable"

* tag 'ceph-for-4.13-rc8' of git://github.com/ceph/ceph-client:
  ceph: fix readpage from fscache

Pull input fixes from Dmitry Torokhov:
 "Just a couple drivers fixes (Synaptics PS/2, Xpad)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: xpad - fix PowerA init quirk for some gamepad models
  Input: synaptics - fix device info appearing different on reconnect

Pull two more MMC fixes from Ulf Hansson:
 "MMC core:
   - Fix block status codes

  MMC host:
   - sdhci-xenon: Fix SD bus voltage select"

* tag 'mmc-v4.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-xenon: add set_power callback
  mmc: block: Fix block status codes

Pull sound fixes from Takashi Iwai:
 "Three regression fixes that should be addressed before the final
  release: a missing mutex call in OSS PCM emulation ioctl, ASoC rt5670
  headset detection breakage, and a regression in simple-card parser
  code"

* tag 'sound-4.13-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: simple_card_utils: fix fallback when "label" property isn't present
  ALSA: pcm: Fix power lock unbalance via OSS emulation
  ASoC: rt5670: Fix GPIO headset detection regression

Pull s390 fixes from Martin Schwidefsky:
 "Three more bug fixes for v4.13.

  The two memory management related fixes are quite new, they fix kernel
  crashes that can be triggered by user space.

  The third commit fixes a bug in the vfio ccw translation code"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/mm: fix BUG_ON in crst_table_upgrade
  s390/mm: fork vs. 5 level page tabel
  vfio: ccw: fix bad ptr math for TIC cda translation

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - Regression in chacha20 handling of chunked input

   - Crash in algif_skcipher when used with async io

   - Potential bogus pointer dereference in lib/mpi"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: algif_skcipher - only call put_page on referenced and used pages
  crypto: testmgr - add chunked test cases for chacha20
  crypto: chacha20 - fix handling of chunked input
  lib/mpi: kunmap after finishing accessing buffer

After commit dce4551c ("udp: preserve head state for IP_CMSG_PASSSEC")
we preserve the secpath for the whole skb lifecycle, but we also
end up leaking a reference to it.

We must clear the head state on skb reception, if secpath is
present.

Fixes: dce4551c ("udp: preserve head state for IP_CMSG_PASSSEC")
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 6bc506b4 ("bridge: switchdev: Add forward mark support for
stacked devices") added the 'offload_fwd_mark' bit to the skb in order
to allow drivers to indicate to the bridge driver that they already
forwarded the packet in L2.

In case the bit is set, before transmitting the packet from each port,
the port's mark is compared with the mark stored in the skb's control
block. If both marks are equal, we know the packet arrived from a switch
device that already forwarded the packet and it's not re-transmitted.

However, if the packet is transmitted from the bridge device itself
(e.g., br0), we should clear the 'offload_fwd_mark' bit as the mark
stored in the skb's control block isn't valid.

This scenario can happen in rare cases where a packet was trapped during
L3 forwarding and forwarded by the kernel to a bridge device.

Fixes: 6bc506b4 ("bridge: switchdev: Add forward mark support for stacked devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Yotam Gigi <yotamg@mellanox.com>
Tested-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mlxsw driver relies on NETDEV_CHANGEUPPER events to configure the
device in case a port is enslaved to a master netdev such as bridge or
bond.

Since the driver ignores events unrelated to its ports and their
uppers, it's possible to engineer situations in which the device's data
path differs from the kernel's.

One example to such a situation is when a port is enslaved to a bond
that is already enslaved to a bridge. When the bond was enslaved the
driver ignored the event - as the bond wasn't one of its uppers - and
therefore a bridge port instance isn't created in the device.

Until such configurations are supported forbid them by checking that the
upper device doesn't have uppers of its own.

Fixes: 0d65fc13 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nogah Frankel <nogahf@mellanox.com>
Tested-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When mounting to older servers, such as Windows XP (or even Windows 7),
the limited error messages that can be passed back to user space can
get confusing since the default dialect has changed from SMB1 (CIFS) to
more secure SMB3 dialect. Log additional information when the user chooses
to use the default dialects and when the server does not support the
dialect requested.
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>

Pull cifs fixes from Steve French:
 "Two cifs bug fixes for stable"

* tag 'cifs-fixes-for-4.13-rc7-and-stable' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: remove endian related sparse warning
  CIFS: Fix maximum SMB2 header size

Pull block fixes from Jens Axboe:
 "Unfortunately a few issues that warrant sending another pull request,
  even if I had hoped to avoid it. This contains:

   - A fix for multiqueue xen-blkback, on tear down / disconnect.

   - A few fixups for NVMe, including a wrong bit definition, fix for
     host memory buffers, and an nvme rdma page size fix"

* 'for-linus' of git://git.kernel.dk/linux-block:
  nvme: fix the definition of the doorbell buffer config support bit
  nvme-pci: use dma memory for the host memory buffer descriptors
  nvme-rdma: default MR page size to 4k
  xen-blkback: stop blkback thread of every queue in xen_blkif_disconnect

Merge tag 'for-4.13/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - A couple fixes for bugs introduced as part of the blk_status_t block
   layer changes during the 4.13 merge window

 - A printk throttling fix to use discrete rate limiting state for each
   DM log level

 - A stable@ fix for DM multipath that delays request requeueing to
   avoid CPU lockup if/when the request queue is "dying"

* tag 'for-4.13/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm mpath: do not lock up a CPU with requeuing activity
  dm: fix printk() rate limiting code
  dm mpath: retry BLK_STS_RESOURCE errors
  dm: fix the second dec_pending() argument in __split_and_process_bio()