- 30 Sep, 2014 7 commits
-
-
Douglas Gilbert authored
A deadlock has been reported when the completion of SCSI commands (simulated by a timer) was surprised by a module removal. This patch removes one half of the offending locks around timer deletions. This fix is applied both to stop_all_queued() which is were the deadlock was discovered and stop_queued_cmnd() which has very similar logic. This patch should be applied both to the lk 3.17 tree and Christoph's drivers-for-3.18 tree. Tested-and-reported-by:
Milan Broz <gmazyland@gmail.com> Signed-off-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
Christoph Hellwig <hch@lst.de>
-
Mike Christie authored
Dan Carpenter found a issue where be2iscsi would copy the ip from userspace to the driver buffer before checking the len of the data being copied: http://marc.info/?l=linux-scsi&m=140982651504251&w=2 This patch just has us only copy what we the driver buffer can support. Cc: <stable@vger.kernel.org> Tested-by:
John Soni Jose <sony.john-n@emulex.com> Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Signed-off-by:
-
Mike Christie authored
This just has iscsi_tcp support ISCSI_PARAM_LOCAL_PORT which exports the local port being used by the iscsi connection. Signed-off-by:
-
John Soni Jose authored
Bump the driver version Signed-off-by:
Jayamohan Kallickal <jayamohan.kallickal@emulex.com> Signed-off-by:
-
John Soni Jose authored
In the reboot/shutdown path, workqueue was destroyed after the adapter resource were freed. The task associated with workqueue was getting executed after resources were freed. This lead to kernel panic. Signed-off-by:
-
Andreea-Cristina Bernat authored
The uses of "rcu_assign_pointer()" are NULLing out the pointers. According to RCU_INIT_POINTER()'s block comment: "1. This use of RCU_INIT_POINTER() is NULLing out the pointer" it is better to use it instead of rcu_assign_pointer() because it has a smaller overhead. The following Coccinelle semantic patch was used: @@ @@ - rcu_assign_pointer + RCU_INIT_POINTER (..., NULL) Signed-off-by:
Andreea-Cristina Bernat <bernat.ada@gmail.com> Acked-by:
Vasu Dev <vasu.dev@intel.com> Signed-off-by:
-
Chris Leech authored
add support for 20 Gbit and 40 Gbit links Signed-off-by:
Chris Leech <cleech@redhat.com> Signed-off-by:
-
- 26 Sep, 2014 1 commit
-
-
Christoph Hellwig authored
Fix a typo in the IPR_IOASC_HW_CMD_FAILED declaration. Based on a patch from Wen Xiong <wenxiong@linux.vnet.ibm.com>. Signed-off-by:
-
- 25 Sep, 2014 32 commits
-
-
Himanshu Madhani authored
Signed-off-by:
Himanshu Madhani <himanshu.madhani@qlogic.com> Signed-off-by:
Saurav Kashyap <saurav.kashyap@qlogic.com> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
Giridhar Malavali <giridhar.malavali@qlogic.com> Signed-off-by:
-
Quinn Tran authored
Signed-off-by:
Quinn Tran <quinn.tran@qlogic.com> Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
-
Quinn Tran authored
Through the qla target code, the qlt_send_term_exchange() routine is used in various different places to cleanup an exchange. For the case of IOCB request queue is full, the exchange is left unhandled/ dangling. Existing code does not have re-try logic to cleanup the exchange. This patch add retry logic to cleanup the exchange before letting new commands through. For the case of FW running out of exchanges, driver need to reply SAM_STAT_BUSY to the initiators. This patch add a pending queue for the busy reply in case IOCB queue is unable to handle the cmd. Cc: <stable@vger.kernel.org> Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Arun Easi authored
ABTS path takes path similar to regular task management, but reset_count was not initialized when allocating mcmd causing the response to get dropped in qlt_xmit_tm_rsp. Fix this by initializing reset_count correctly. Signed-off-by:
Arun Easi <arun.easi@qlogic.com> Signed-off-by:
-
Arun Easi authored
A chip reset can occur after driver submits command to the stack. Abort command processing if a chip reset has occurred or in progress when you get a follow up for a command. Signed-off-by:
-
Arun Easi authored
Signed-off-by:
-
Himanshu Madhani authored
tcm_qla2xxx_get_task_tag incorrectly assume command is qla_tgt_cmd. Add check to see if it's a scsi cmd or task mgmt command. Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Arun Easi authored
Sequence level error recovery (aka FC Tape) is not really required for disk devices. On heavily loaded system, with slow turn around, a bunch of status enquiries using REC puts additional burden to the target, so just turn off SLER by default. Signed-off-by:
-
Arun Easi authored
Turning logging bits for target mode ON dumps quite a lot verbose messages, remove those and change some of the IO path logging to use IO bits. Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
-
Arun Easi authored
Cc: <stable@vger.kernel.org> Signed-off-by:
-
Himanshu Madhani authored
This patch is to fix regression added by commit id 51a07f84. When allocating memory for new session original patch does not assign vha to op->vha resulting into NULL pointer access during qlt_create_sess_from_atio(). Cc: <stable@vger.kernel.org> Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
-
Saurav Kashyap authored
Signed-off-by:
-
Joe Carnuccio authored
Signed-off-by:
Joe Carnuccio <joe.carnuccio@qlogic.com> Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
Sawan Chandak <sawan.chandak@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
If we fail to load one of the segments of firmware fail the operation instead of trying to continue which will lead to a system crash since the pointers to the next segment will not be updated correctly. Signed-off-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
Disable the PCI device during shutdown to prevent any races with other PCI code such as the AER handling code. Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Himanshu Madhani authored
For FA-WWPN capable device, ISP2031 and ISP27XX, when loop dead is detected by a driver, restore WWPN from NVRAM. Signed-off-by:
-
Chad Dupuis authored
Parse the retry delay timer field from the FCP response data and if: - It is not zero - The SCSI status is busy or queue full return SCSI_MLQUEUE_TARGET_BUSY for the number of milliseconds specified in the retry delay timer field. Signed-off-by:
-
Alex Vechersky authored
Signed-off-by:
Alex Vechersky <alex.vechersky@qlogic.com> Signed-off-by:
-
Chad Dupuis authored
Signed-off-by:
-
Nigel Kirkland authored
Signed-off-by:
Nigel Kirkland <nigel.kirkland@qlogic.com> Signed-off-by:
-
Himanshu Madhani authored
Nameserver data on FC switch is not refreshed when qla2xxx driver is unloaded. Disabling laser for ISP2031 will force FC switch to rescan ports and clear fdmi entries from Nameserver. Signed-off-by:
-
Himanshu Madhani authored
Signed-off-by:
-
Quinn Tran authored
Declaration error of mb array in qla2x00_iidma_fcport cause data to be written beyond the array. This ends up causing stack corruption. Signed-off-by:
-
Sawan Chandak authored
Signed-off-by:
-
