- 21 Jan, 2014 40 commits
-
-
Alexander Shiyan authored
This patch simplifies probe() and remove() functions by moving some initialisation code out from the I2C/SPI init() and exit() functions and into the core driver. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Alexander Shiyan authored
Symbol MFD_MC13783 always selected by MFD_MC13XXX, so no need to keep additional symbol. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Alexander Shiyan authored
mc13xxx_get_flags() declaration given twice. This patch removes this duplicate. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Stephen Boyd authored
This is a read-only data structure. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Stephen Boyd authored
In preparation for passing a const pointer directly to ssbi_write() from the regmap APIs. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Stephen Boyd authored
The ssbi driver assumes that the device is DT based. Remove the platform data structs that will never be used and hide the enum in the only C file that uses it. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Stephen Warren authored
mfd_add_device() assigns .of_node in the device objects it creates only if the mfd_cell for the device has the .of_compatible field set and the DT node for the top-level MFD device contains a child whose compatible property matches the cell's .of_compatible field. This leaves .of_node unset in many cases. When this happens, entries in the DT /aliases property which refer to the top-level MFD DT node will never match the MFD child devices, hence causing the requested alias not to be honored. Solve this by setting each MFD child device's .of_node equal to the top- level MFD device's .of_node field in the cases where it would otherwise remain unset. The first use-case for this will be aliases for the TPS6586x's RTC device. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Rhyland Klein authored
The EC has specific timing it requires. Add support for an optional delay after raising CS to fix timing issues. This is configurable based on a DT property "google,cros-ec-spi-msg-delay". If this property isn't set, then no delay will be added. However, if set it will cause a delay equal to the value passed to it to be inserted at the end of a transaction. Signed-off-by: Rhyland Klein <rklein@nvidia.com> Reviewed-by: Bernie Thompson <bhthompson@chromium.org> Reviewed-by: Andrew Bresticker <abrestic@chromium.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Thierry Reding authored
memset() was being called with the second parameter set to '\0', which is equivalent but longer than the more canonical 0. Update the code to use the latter variant consistently across the driver. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Thierry Reding authored
The driver is not used on any non-DT platform, so it can depend on the OF Kconfig symbol to make that explicit. This is in preparation of a subsequent patch which parses some parameters from the device tree and would otherwise have to conditionalize that code. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Thierry Reding authored
According to the header comment in the source file the driver is licensed under GPL v2, so update MODULE_LICENSE() to match that. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Wei Yongjun authored
Fixes the following sparse warning: drivers/mfd/sec-core.c:202:16: warning: Using plain integer as NULL pointer Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Wei Yongjun authored
In case of error, the function devm_regmap_init_mmio() returns ERR_PTR() and never returns NULL. The NULL test in the return value check should be replaced with IS_ERR(). Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Alexander Shiyan authored
Checking for maximal register is already provided by regmap API, so remove redundant checks. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Stefan Agner authored
Depending on the regulator version, the voltage table might be different. Use version specific regulator tables in order to select correct voltage table. For the following regulator versions different voltage tables are now used: * TPS658623: Use correct voltage table for SM2 * TPS658643: New voltage table for SM2 Both versions are in use on the Colibri T20 module. Make use of the correct tables by requesting the correct SM2 voltage of 1.8V. This change is not backward compatible since an old driver is not able to correctly set that value. The value 1.8V is out of range for the old driver and will refuse to probe the device. The regulator starts with default settings and the driver shows appropriate error messages. On Colibri T20, the old value used to work with TPS658623 since the driver applied a wrong voltage table too. However, the TPS658643 used on V1.2 devices uses yet another voltage table and those broke that pseudo-compatibility. The regulator driver now has the correct voltage table for both regulator versions and those the correct voltage can be used in the device tree. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Thierry Reding <treding@nvidia.com> Acked-by: Mark Brown <broonie@linaro.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Stefan Agner authored
Use the VERSIONCRC to determine the exact device version. According to the datasheet this register can be used as device identifier. The identification is needed since some tps6586x regulators use a different voltage table. Signed-off-by: Stefan Agner <stefan@agner.ch> Reviewed-by: Thierry Reding <treding@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Milo Kim authored
This is the other of the LP3943 MFD driver. LP3943 can be used as a PWM generator, up to 2 channels. * Two PWM generators supported * Supported PWM operations request, free, config, enable and disable * Pin assignment A driver data, 'pin_used' is checked when a PWM is requested. If the output pin is already assigned, then returns as failure. If the pin is available, 'pin_used' is set. When the PWM is not used anymore, then it is cleared. It is defined as unsigned long type for atomic bit operation APIs, but only LSB 16bits are used because LP3943 has 16 outputs. Signed-off-by: Milo Kim <milo.kim@ti.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Milo Kim authored
LP3943 has 16 output pins which can be used as GPIO expander and PWM generator. * Regmap I2C interface for R/W LP3943 registers * Atomic operations for output pin assignment The driver should check whether requested pin is available or not. If the pin is already used, pin request returns as a failure. A driver data, 'pin_used' is checked when gpio_request() and pwm_request() are called. If the pin is available, then pin_used is set. And it is cleared when gpio_free() and pwm_free(). * Device tree support Compatible strings for GPIO and PWM driver. LP3943 platform data is PWM related, so parsing the device tree is implemented in the PWM driver. Signed-off-by: Milo Kim <milo.kim@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Milo Kim authored
This is one of LP3943 MFD driver. LP3943 is configurable as a GPIO expander, up to 16 GPIOs. * Application note: how to configure LP3943 as a GPIO expander http://www.ti.com/lit/an/snva287a/snva287a.pdf * Supported GPIO controller operations request, free, direction_input, direction_output, get and set * GPIO direction register not supported LP3943 doesn't have the GPIO direction register. It only provides input and output status registers. So, private data for the direction should be handled manually. This variable is updated whenever the direction is changed and used in 'get' operation. * Pin assignment A driver data, 'pin_used' is checked when a GPIO is requested. If the GPIO is already assigned, then returns as failure. If the GPIO is available, 'pin_used' is set. When the GPIO is not used anymore, then it is cleared. It is defined as unsigned long type for atomic bit operation APIs, but only LSB 16bits are used because LP3943 has 16 outputs. Signed-off-by: Milo Kim <milo.kim@ti.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Milo Kim authored
Bindings for LP3943 MFD, GPIO and PWM controller are added. Signed-off-by: Milo Kim <milo.kim@ti.com> Acked-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Dan Carpenter authored
"pdata" is a NULL not an ERR_PTR so there is no use printing it. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Mark Brown authored
This helps move us towards removing the bus custom operations. Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Linus Walleij authored
All subdrivers use the irqdomain to demux AB8500 IRQs but here in the hierarchical path we find a leftover instance using the hard-coded IRQ base. Convert it to use irqdomain with a oneliner. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Lee Jones authored
drivers/mfd/rtl8411.c: In function 'rtl8411_fetch_vendor_settings': drivers/mfd/rtl8411.c:58:7: warning: 'reg1' is used uninitialized in this function [-Wuninitialized] drivers/mfd/rtl8411.c: In function 'rtl8411b_fetch_vendor_settings': drivers/mfd/rtl8411.c:79:7: warning: 'reg' is used uninitialized in this function [-Wuninitialized] drivers/mfd/rtl8411.c: In function 'rtl8411_fetch_vendor_settings': drivers/mfd/rtl8411.c:69:26: warning: 'reg3' may be used uninitialized in this function [-Wuninitialized] Tested-by: Micky Ching <micky_ching@realsil.com.cn> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Jingoo Han authored
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro is not preferred. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Linus Walleij authored
This deletes the special AB8500 GPIO platform data passing header and merges the few remaining contents down into the abx500 pinctrl driver which handles the abx500 GPIO device. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Linus Walleij authored
This deletes all instances where the AB8500 GPIO platform data is passed around. It is completely unused in the kernel now, so it does not hurt anyone. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Lee Jones authored
Immutable branch for IIO and Input
-
Lee Jones authored
Immutable branch between MFD and ASoC due for the v3.14 merge window
-
Lee Jones authored
Immutable branch for ASoC, as requested by Mark Brown
-
Linus Walleij authored
All instances of this device are now coming from device tree- enabled platforms probing without using platform data. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Tony Lindgren authored
Since we still need to rely on a mix of device tree initialized drivers and legacy platform data initialize drivers, let's fix the passing of platform data to twl4030-gpio. As the twl4030 GPIO is initialized by twl-core.c, we need to register the auxdata for twl4030 GPIO in twl-core.c. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Ruslan Ruslichenko authored
Since currently nobody uses TWL603x platform data and all new users will supply it through device tree, handling of these data within twl-core will never be used, so remove it. Signed-off-by: Ruslan Ruslichenko <ruslan.ruslichenko@globallogic.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Krzysztof Kozlowski authored
Add "const" to "static struct regmap_irq" and "static struct regmap_config". Acked-by: Sangbeom Kim <sbkim73@samsung.com> Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Krzysztof Kozlowski authored
Match max14577 regulator driver by of_compatible specified in mfd_cell. Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Chanwoo Choi authored
This patch adds max14577 core/irq driver to support MUIC(Micro USB IC) device and charger device and support irq domain method to control internal interrupt of max14577 device. Also, this patch supports DT binding with max14577_i2c_parse_dt(). The MAXIM 14577 chip contains Micro-USB Interface Circuit and Li+ Battery Charger. It contains accessory and USB charger detection logic. It supports USB 2.0 Hi-Speed, UART and stereo audio signals over Micro-USB connector. The battery charger is compliant with the USB Battery Charging Specification Revision 1.1. It has also SFOUT LDO output for powering USB devices. Reviewed-by: Mark Brown <broonie@linaro.org> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Krzysztof Kozlowski authored
Add PM suspend/resume ops to the sec MFD core driver and make it a wake up source. This allows proper waking from suspend to RAM and also fixes broken interrupts after resuming: [ 42.705703] sec_pmic 7-0066: Failed to read IRQ status: -5 Interrupts stop working after first resume initiated by them (e.g. by RTC Alarm interrupt) because interrupt registers were not cleared properly. When device is woken up from suspend by RTC Alarm, an interrupt occurs before resuming I2C bus controller. The interrupt is handled by regmap_irq_thread which tries to read RTC registers. This read fails (I2C is still suspended) and RTC Alarm interrupt is disabled. Disable the S5M8767 interrupts during suspend (disable_irq()) and enable them during resume so the device will be still woken up but the interrupt won't happen before resuming I2C bus. Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Thierry Reding authored
Rename cros_ec_{probe,remove}_i2c() to cros_ec_i2c_{probe,remove}() for consistency. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Thierry Reding authored
Rename cros_ec_{probe,remove}_spi() to cros_ec_spi_{probe,remove}() for consistency. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-
Jingoo Han authored
The driver core clears the driver data to NULL after device_release or on probe failure. Thus, it is not needed to manually clear the device driver data to NULL. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
-