- 05 Jun, 2009 19 commits
-
-
Philipp Zabel authored
I'm not going to maintain separate defconfigs for magician and hx4700. This should probably be renamed to htcpxa_defconfig. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Philipp Zabel authored
This includes - IrDA (pxafixp_ir), - Buttons (gpio-keys), - ASIC3 IRQ/GPIOs (asic3), - EGPIOs (htc-egpio), - ATI Imageon w3220 framebuffer (w100fb), - Backlight (pwm-backlight), - StrataFlash (physmap), - Battery monitor (ds1wm,w1_ds2760,ds2760_battery) - USB gadget support (pxa27x_udc,gpio_vbus). - bq24022 battery charger (pda_power,bq24022) - TSC2046 touchscreen (ads7846) Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Philipp Zabel authored
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Philipp Zabel authored
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Robert Jarzmik authored
Add voltage regulation capability to pxa2xx cpufreq driver. The cpufreq will ask for a "vcc_core" regulator to the regulator framework. If a regulator is found at probe time, it will be used with values specified in PXA270 Electrical, Mechanical, and Thermal Specifications. If not, it will be assumed for now that frequency change will work without voltage control. This assumes that the IPL/SPL installs sane values to an existing voltage regulator (ie. voltage high enough to support the full range). Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Jürgen Schindele authored
Signed-off-by: Jürgen Schindele <linux@schindele.name> Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
-
Mike Rapoport authored
PXA processors have several low-power modes. Currently kernel supports only one of these modes for PM_SUSPEND_MEM. This patch adds ability to set desired suspend mode for PXA27x based machines. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Reviewed-by: Russell King <linux@arm.linux.org.uk> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Robert Jarzmik authored
As reported by Aric Blumer, the pxa27x_udc driver does work with pxa3xx devices. Add support into device files. Reported-by: Aric Blumer <aric@sdgsystems.com> Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Matt Reimer <mattjreimer@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Philipp Zabel authored
The default value is 16 IRQs. Zylonite needs 32, ASIC3 based boards need 70. My problem is still that due to the way IRQ_GPIO is hardcoded, ASIC3 based boards need 70 IRQs starting at IRQ_BOARD_START. If I define ASIC3 IRQs similar to LoCoMo or SA1111, things break as soon as something selects PXA_HAVE_BOARD_IRQS. Increasing the default number of board IRQs to 70 instead doesn't seem very nice. Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Mike Rapoport authored
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Eric Miao authored
Signed-off-by: Mingwei Wang <mingwei.wang@marvell.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Eric Miao authored
Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Eric Miao authored
Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Eric Miao authored
The PXA_PWM config option is really redundant since the introduction of HAVE_PWM, replace that with HAVE_PWM to avoid confusion. Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Eric Miao authored
PWMs on PXA168/910 start at number 1 instead of 0, (i.e. PWM1/2/3/4 instead of PWM0/1/2/3 on PXA25x/PXA27x/PXA3xx). Allow this number to be specified in pwm_id_table. Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Eric Miao authored
Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Eric Miao authored
Signed-off-by: Paul Shen <paul.shen@marvell.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Eric Miao authored
Signed-off-by: Paul Shen <paul.shen@marvell.com> Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
Eric Miao authored
Signed-off-by: Eric Miao <eric.miao@marvell.com>
-
- 03 Jun, 2009 2 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpcLinus Torvalds authored
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: powerpc/pmac: Update PowerMac 32-bit defconfig
-
- 02 Jun, 2009 11 commits
-
-
Alan Cox authored
Ideally we should have a directory of drivers and a link to the 'active' driver. For now just show the first device which is effectively the existing semantics without a warning. This is an update on the original buggy patch that I then forgot to resubmit. Confusingly it was proposed by Red Hat, written by Etched Pixels fixed and submitted by Intel ... Resolves-Bug: http://bugzilla.kernel.org/show_bug.cgi?id=9749Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Alan Cox authored
This matches Bartlomiej's patch for ide_pci_generic: c339dfdd In the libata case netcell has its own mini driver. I suspect this fix is actually only needed for some firmware revs but it does no harm either way. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup e1000: add missing length check to e1000 receive routine forcedeth: add phy_power_down parameter, leave phy powered up by default (v2) Bluetooth: Remove useless flush_work() causing lockdep warnings
-
git://oss.sgi.com/xfs/xfsLinus Torvalds authored
* 'for-linus' of git://oss.sgi.com/xfs/xfs: xfs: prevent deadlock in xfs_qm_shake() xfs: fix overflow in xfs_growfs_data_private xfs: fix double unlock in xfs_swap_extents()
-
Minoru Usui authored
net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup This patch fixes a bug which unconfigured struct tcf_proto keeps chaining in tc_ctl_tfilter(), and avoids kernel panic in cls_cgroup_classify() when we use cls_cgroup. When we execute 'tc filter add', tcf_proto is allocated, initialized by classifier's init(), and chained. After it's chained, tc_ctl_tfilter() calls classifier's change(). When classifier's change() fails, tc_ctl_tfilter() does not free and keeps tcf_proto. In addition, cls_cgroup is initialized in change() not in init(). It accesses unconfigured struct tcf_proto which is chained before change(), then hits Oops. Signed-off-by: Minoru Usui <usui@mxm.nes.nec.co.jp> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Tested-by: Minoru Usui <usui@mxm.nes.nec.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Neil Horman authored
Patch to fix bad length checking in e1000. E1000 by default does two things: 1) Spans rx descriptors for packets that don't fit into 1 skb on recieve 2) Strips the crc from a frame by subtracting 4 bytes from the length prior to doing an skb_put Since the e1000 driver isn't written to support receiving packets that span multiple rx buffers, it checks the End of Packet bit of every frame, and discards it if its not set. This places us in a situation where, if we have a spanning packet, the first part is discarded, but the second part is not (since it is the end of packet, and it passes the EOP bit test). If the second part of the frame is small (4 bytes or less), we subtract 4 from it to remove its crc, underflow the length, and wind up in skb_over_panic, when we try to skb_put a huge number of bytes into the skb. This amounts to a remote DOS attack through careful selection of frame size in relation to interface MTU. The fix for this is already in the e1000e driver, as well as the e1000 sourceforge driver, but no one ever pushed it to e1000. This is lifted straight from e1000e, and prevents small frames from causing the underflow described above Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Tested-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ed Swierk authored
Add a phy_power_down parameter to forcedeth: set to 1 to power down the phy and disable the link when an interface goes down; set to 0 to always leave the phy powered up. The phy power state persists across reboots; Windows, some BIOSes, and older versions of Linux don't bother to power up the phy again, forcing users to remove all power to get the interface working (see http://bugzilla.kernel.org/show_bug.cgi?id=13072). Leaving the phy powered on is the safest default behavior. Users accustomed to seeing the link state reflect the interface state and/or wanting to minimize power consumption can set phy_power_down=1 if compatibility with other OSes is not an issue. Signed-off-by: Ed Swierk <eswierk@aristanetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Felix Blyakher authored
It's possible to recurse into filesystem from the memory allocation, which deadlocks in xfs_qm_shake(). Add check for __GFP_FS, and bail out if it is not set. Signed-off-by: Felix Blyakher <felixb@sgi.com> Signed-off-by: Hedi Berriche <hedi@sgi.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Felix Blyakher <felixb@sgi.com>
-
Eric Sandeen authored
In the case where growing a filesystem would leave the last AG too small, the fixup code has an overflow in the calculation of the new size with one fewer ag, because "nagcount" is a 32 bit number. If the new filesystem has > 2^32 blocks in it this causes a problem resulting in an EINVAL return from growfs: # xfs_io -f -c "truncate 19998630180864" fsfile # mkfs.xfs -f -bsize=4096 -dagsize=76288719b,size=3905982455b fsfile # mount -o loop fsfile /mnt # xfs_growfs /mnt meta-data=/dev/loop0 isize=256 agcount=52, agsize=76288719 blks = sectsz=512 attr=2 data = bsize=4096 blocks=3905982455, imaxpct=5 = sunit=0 swidth=0 blks naming =version 2 bsize=4096 ascii-ci=0 log =internal bsize=4096 blocks=32768, version=2 = sectsz=512 sunit=0 blks, lazy-count=0 realtime =none extsz=4096 blocks=0, rtextents=0 xfs_growfs: XFS_IOC_FSGROWFSDATA xfsctl failed: Invalid argument Reported-by: richard.ems@cape-horn-eng.com Signed-off-by: Eric Sandeen <sandeen@sandeen.net> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Felix Blyakher <felixb@sgi.com> Signed-off-by: Felix Blyakher <felixb@sgi.com>
-
Felix Blyakher authored
Regreesion from commit ef8f7fc5, which rearranged the code in xfs_swap_extents() leading to double unlock of xfs inode ilock. That resulted in xfs_fsr deadlocking itself on platforms, which don't handle double unlock of rw_semaphore nicely. It caused the count go negative, which represents the write holder, without really having one. ia64 is one of the platforms where deadlock was easily reproduced and the fix was tested. Signed-off-by: Eric Sandeen <sandeen@sandeen.net> Reviewed-by: Eric Sandeen <sandeen@sandeen.net> Signed-off-by: Felix Blyakher <felixb@sgi.com>
-
Benjamin Herrenschmidt authored
This mostly adds back AppleTouch support and adds CONFIG_HIGHMEM by default. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
-
- 01 Jun, 2009 8 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: hash - Fix handling of sg entry that crosses page boundary
-
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/stagingLinus Torvalds authored
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: hwmon: Update documentation on fan_max hwmon: (lm78) Add missing __devexit_p()
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc64: Fix section attribute warnings. sparc64: Fix SET_PERSONALITY to not clip bits outside of PER_MASK.
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: 3c509: Add missing EISA IDs MAINTAINERS: take maintainership of the cpmac Ethernet driver net/firmare: Ignore .cis files ath1e: add new device id for asus hardware mlx4_en: Fix a kernel panic when waking tx queue rtl8187: add USB ID for Linksys WUSB54GC-EU v2 USB wifi dongle at76c50x-usb: avoid mutex deadlock in at76_dwork_hw_scan mac8390: fix build with NET_POLL_CONTROLLER cxgb3: link fault fixes cxgb3: fix dma mapping regression netfilter: nfnetlink_log: fix wrong skbuff size calculation netfilter: xt_hashlimit does a wrong SEQ_SKIP bfin_mac: fix build error due to net_device_ops convert atlx: move modinfo data from atlx.h to atl1.c gianfar: fix babbling rx error event bug cls_cgroup: read classid atomically in classifier netfilter: nf_ct_dccp: add missing DCCP protocol changes in event cache netfilter: nf_ct_tcp: fix accepting invalid RST segments
-
git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/headers-check-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/headers-check-2.6: headers_check fix: linux/net_dropmon.h headers_check fix: linux/auto_fs.h
-
Christian Engelmayer authored
Add fan_max description. Add fan limit alarm 'max_alarm' to the alarm section. Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jean Delvare <khali@linux-fr.org>
-
Mike Frysinger authored
The remove function uses __devexit, so the .remove assignment needs __devexit_p() to fix a build error with hotplug disabled. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Jean Delvare <khali@linux-fr.org>