OMAP4 has an AES module that uses the omap-aes crypto driver.
Add DT entries for the same.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Set bus-width to make SD card operate in 4 bit mode.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order
to detect eMMC on BBB and BBW + eMMC cape.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The IGEP AQUILA EXPANSION board is a development platform
for the IGEP COM AQUILA AM335x boards.

The board adds the following connectivity:

    o USB OTG
    o USB HOST
    o HDMI
    o Ethernet
    o Serial Debug (3.3V)
    o 2x46 pin headers
    o EEPROM
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The IGEP COM AQUILA is industrial processors SODIMM module with
following highlights:

   o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor
   o Cortex-A8 ARM CPU
   o 3.3 volts Inputs / Outputs use industrial
   o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
   o MicroSD card reader on-board
   o Ethernet controller on-board
   o JTAG debug connector available
   o Designed for industrial range purposes
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

3.3V fixed regulator does not belong to TPS node - as a result
the fixed regulator is never probed and MMC is continually deferred
due to lack of regulator.

Move the fixed regulator to be at root of platform.

Cc: Joel Fernandes <joelf@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add information about the USB OTG PHY. Without this
the OTG port on beagle will not work.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Provide RESET GPIO and Power regulator for the USB PHY,
the USB Host port mode and the PHY device for the controller.
Also provide pin multiplexer information for USB host pins.

We also relocate omap3_pmx_core pin definations so that they
are close to omap3_pmx_wkup pin definations.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Set the alias for ethernet0 and ethernet1 so that uBoot
can set the MAC address appropriately.

Currently u-boot cannot find the alias and there for does
not set the MAC address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add DT nodes for TPS659038 PMIC on DRA7 boards.

It is based on top of:
http://comments.gmane.org/gmane.linux.ports.arm.omap/102459.

Documentation:
- Documentation/devicetree/bindings/mfd/palmas.txt
- Documentation/devicetree/bindings/regulator/palmas-pmic.txt

Boot Tested on DRA7 d1 Board.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix indentation and changelog]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

"gpmc,sync-clki-ps" is not defined/documented, it should be
"gpmc,sync-clk-ps" instead.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The On Chip Peripherals (OCP) device node is a simplified
representation of the AM33XX SoC interconnect. An OCP dev
node is already defined in the am33xx.dtsi Device Tree
source file included by am33xx based boards so there is
no need to redefine this on each board DT file.

Also, the OCP and IP modules directly connected to it are SoC
internal details that is better to keep outside of board files.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

am33xx boards DTS include the am33xx.dtsi Device Tree
source file that already define a pinmux device node for
the AM33XX SoC Pin Multiplex.

Redefining this for each board makes the Device Tree files
harder to modify and maintain so let's just use what is
already defined in the included .dtsi file.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This matches the vendor 3.8.x configuration that is shipping
with the boards.

The LED layout is now:
 USR0: heartbeat
 USR1: mmc0 (micro-SD slot)
 USR2: cpu0
 USR3: mmc1 (eMMC)

The cpu0 triggers was put in between the mmc triggers to make
is easier to see where the disk activity is.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The micro-SD slot hooks up all four data pins so lets' use them.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The pinmux is specified in am335x-bone-common.dtsi to be
reused by the eMMC cape.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
[bcousson@baylibre.com: Fix traling spaces and useless comments]
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This enables the use of MMC cards even when no card was inserted at boot.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Adds AM33XX MMC support for am335x-bone, am335x-evm and am335x-evmsk boards.

Also added is the DMA binding definitions based on the generic DMA request
binding.

Additional changes made to DTS:
* Interrupt, reg and compatible properties added
* ti,needs-special-hs-handling added
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Adds DMA resources to the AM33XX SPI nodes.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Adds AM33XX EDMA support to the am33xx.dtsi as documented in
Documentation/devicetree/bindings/dma/ti-edma.txt

[Joel Fernandes <joelf@ti.com>]
Drop DT entries that are non-hardware-description as discussed in [1]

[1] https://patchwork.kernel.org/patch/2226761/Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Without this node, there will be no palmas driver to notify
dwc3 that a cable has been connected and, without that, dwc3
will never initialize.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[kishon@ti.com: added dt properties for enabling vbus/id interrupts
and fixed vbus-supply value after SMPS10 is modeled as 2 regulators]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Use a common naming scheme "mode0name.modename flags" for the
USB host pins to be consistent.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This adds devicetree for gta04 (Openmoko next generation board) with necessary
support for mmc, usb, leds and button.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Populate uarts, timers, rtc, wdt, gpio, i2c, spi, cpsw & pwm nodes.

Reason for adding these nodes early - hwmod code required address
space of peripherals corresponding to these nodes (as address space
details are removed from hwmod database).

uart0, timers - 1 & 2 and synctimer were already present, so here the
remaining uarts & timers are added.

All properties as per the existing binding has been added for uart,
timer, rtc, wdt & gpio. Even though that was not the current scope
of work, felt adding those would reduce or require no effort later
to get these peripherals working.

For i2c, spi, cpsw & pwm - only the properties that were sure to be
correct has been added (main intention is to make hwmod happy and
avoid any later modification to here added properties).

While at it add "ti,hwmod" property to already existing nodes.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Update AM4372 cpu node to the latest cpus/cpu bindings for ARM.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add minimal device tree source needed for DRA7 based SoCs.
Also add a board dts file for the dra7-evm (based on dra752)
which contains 1.5G of memory with 1G interleaved and 512MB
non-interleaved. Also added in the board file are pin configuration
details for i2c, mcspi and uart devices on board.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.

Tested on OMAP4 SDP board and Pandaboard ES2.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

SMPS10 has two outputs OUT1 and OUT2. Hence SMPS10 is modeled as
two regulators. The DT node is split to reflect it.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Following commit ff5c9059 and therefore other omap platforms using
the gpio-omap driver correct the #interrupt-cells property on am33xx
too. The omap gpio binding documentaion also states that
the #interrupt-cells property should be 2.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

ARM Performance Monitor Units are available on the am33xx,
add the support in the dtsi.

Tested with perf and oprofile on a regular beaglebone.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>