Since the usb2 phy driver for gen3 (phy-rcar-gen3-usb2) cannot access
LPSTS and UGCTRL2 registers in the HSUSB module, this driver have to
initialize the registers. So, this patch adds such handling code into
rcar3.c.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Enable SuperSpeedPlus by programming the DCFG.speed and after
enumerating, set gadget->speed appropriately.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

If the maximum_speed is not set, set it to a known value, either
SuperSpeed or SuperSpeedPlus based on the type of controller we are
using. If we are on DWC_usb31 controller, check the PHY interface to see
if it is capable of SuperSpeedPlus.

Also this check is moved after dwc3_core_init() so that we can check
dwc->revision.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Update various places where the speed is checked so that it takes into
account SuperSpeedPlus properly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Update various registers fields definitions for the DWC_usb31 controller
for SuperSpeedPlus support.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Add a convenience function to check if the controller is DWC_usb31.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Enable superspeed plus configuration for the mass storage gadget.

The mass storage function doesn't do anything special for
SuperSpeedPlus. Just pass in the same SuperSpeed descriptors for
SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Update the debug message reporting the speeds that a configuration
supports for SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Configure the usb_ep using the SuperSpeedPlus descriptors if connected
in SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Enable writing of SuperSpeedPlus descriptors for any SuperSpeedPlus
capable configuration when connected in SuperSpeedPlus.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

There are a couple places in the code that get the function descriptors
based on the speed. Move this lookup into a function call and add
support to handle the SuperSpeedPlus descriptors as well.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

If enumerated in SuperSpeedPlus, count the configurations that support
it.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

When a function is added to a configuration with usb_add_function(), the
configuration speed flags are updated. These flags indicate for which
speeds the configuration is valid for.

This patch adds a flag in the configuration for SuperSpeedPlus and
also updates this based on the existence of ssp_descriptors.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Add a ssp_descriptors member to struct usb_function and handle the
initialization and cleanup of it. This holds the SuperSpeedPlus
descriptors for a function that supports SuperSpeedPlus. This is added
by usb_assign_descriptors().
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Add the 'ssp_descriptors' parameter to the usb_assign_descriptors()
function. This allows a function driver to add descriptors for
SuperSpeedPlus speeds if it supports it.

Also update all uses of this function in the gadget subsystem so that
they pass NULL for the ssp_descriptors parameters.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

If a gadget supports SuperSpeedPlus or higher speeds, return a
SuperSpeedPlus USB Device Capability descriptor.

Currently this implementation returns a fixed descriptor with typical
values set.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The USB 3.1 specification replaces the USB 3.0 specification and all new
devices that are running at SuperSpeed or higher speeds must report a
bcdUSB of 0x0310.

Refer to USB 3.1 Specification, Revision 1.0, Section 9.6.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Add a function to check for SuperSpeedPlus capable gadgets.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

The SuperspeedPlus Device Capability Descriptor has a variable size
depending on the number of sublink speed attributes.

This patch adds a macro to calculate that size. The macro takes one
argument, the Sublink Speed Attribute Count (SSAC) as reported by the
descriptor in bmAttributes[4:0].

See USB 3.1 9.6.2.5, Table 9-19.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>

Merge tag 'usb-ci-v4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next

Peter writes:

- Add platform interface to choose ttctrl.ttha
- Some tiny improvements

We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Avoid printing an error if adding the device failes with return
value EPROBE_DEFFER. This may happen e.g. due to missing GPIO for
the vbus-supply regulator.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@nxp.com>

This reverts commit e765bfb7.

In the most of cases, we only use one transaction per frame and the
frame rate may be high, If the platforms want to support multiple
transactions but less frame rate cases like [1] and [2], it can set
"non-zero-ttctrl-ttha" at dts.

[1] http://www.spinics.net/lists/linux-usb/msg123125.html
[2] http://www.spinics.net/lists/linux-usb/msg118679.htmlSigned-off-by: Peter Chen <peter.chen@nxp.com>

If this property is not set, the max packet size is 1023 bytes, and if
the total of packet size for pervious transactions are more than 256 bytes,
it can't accept any transactions within this frame. The use case is single
transaction, but higher frame rate.

If this property is set, the max packet size is 188 bytes, it can handle
more transactions than above case, it can accept transactions until it
considers the left room size within frame is less than 188 bytes, software
needs to make sure it does not send more than 90%
maximum_periodic_data_per_frame. The use case is multiple transactions, but
less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>

In chipidea IP RTL, there is a very limited design for siTD, the detail
like below:
There is no Max Packet Size at siTD, so it uses one constant for both
Max Packet Size for packet and the packet size for the last transaction
when considering schedule.
If the ttctrl.ttha does not match against Hub Address field in siTD,
this constant is 188 bytes, else this constant is 1023 bytes.

If the ttctrl.ttha is non-zero value, RTL will use 188 as this constant,
so it will lose the data if the packet size is larger than 188 bytes, eg,
if we playback a wav which format is 48khz, 16 bits, 2 channels, the
packet size will be 192bytes, but the controller will only send 188 bytes
for this packet, the noise will be heared using USB audio card.
The use case is single transaction, but higher frame rate.

If the ttctr.ttha is zero value, we can send 1023 bytes within one
transaction, but the controller will not accept the coming tranaction
if it considers the schedule time is less than 1023 bytes. So the
limitation is we can't schedule as many as transactions within frame.
If the total bytes is already 256 bytes for previous transactions within
frame, it can't accept another transaction. The use case is multiple
transactions, but less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>

retval is assigned to be -EOVERFLOW but is overwritten later before
it's used, remove this unused value assignment.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>

This patch adds the missing compatible strings from ci_hdrc_imx.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>

Until now the imx23 uses the imx27 platform flag. But the
imx23 needs the flag CI_HDRC_TURN_VBUS_EARLY_ON, too. So
fix this by adding a separate platform flag.
Suggested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>

Pull perf fixes from Thomas Gleixner:
 "A rather largish series of 12 patches addressing a maze of race
  conditions in the perf core code from Peter Zijlstra"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf: Robustify task_function_call()
  perf: Fix scaling vs. perf_install_in_context()
  perf: Fix scaling vs. perf_event_enable()
  perf: Fix scaling vs. perf_event_enable_on_exec()
  perf: Fix ctx time tracking by introducing EVENT_TIME
  perf: Cure event->pending_disable race
  perf: Fix race between event install and jump_labels
  perf: Fix cloning
  perf: Only update context time when active
  perf: Allow perf_release() with !event->ctx
  perf: Do not double free
  perf: Close install vs. exit race

Pull x86 fixes from Thomas Gleixner:
 "This update contains:

   - Hopefully the last ASM CLAC fixups

   - A fix for the Quark family related to the IMR lock which makes
     kexec work again

   - A off-by-one fix in the MPX code.  Ironic, isn't it?

   - A fix for X86_PAE which addresses once more an unsigned long vs
     phys_addr_t hickup"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mpx: Fix off-by-one comparison with nr_registers
  x86/mm: Fix slow_virt_to_phys() for X86_PAE again
  x86/entry/compat: Add missing CLAC to entry_INT80_32
  x86/entry/32: Add an ASM_CLAC to entry_SYSENTER_32
  x86/platform/intel/quark: Change the kernel's IMR lock bit to false

Pull scheduler fixlet from Thomas Gleixner:
 "A trivial printk typo fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/deadline: Fix trivial typo in printk() message

Pull irq fixes from Thomas Gleixner:
 "Four small fixes for irqchip drivers:

   - Add missing low level irq handler initialization on mxs, so
     interrupts can acutally be delivered

   - Add a missing barrier to the GIC driver

   - Two fixes for the GIC-V3-ITS driver, addressing a double EOI write
     and a cache flush beyond the actual region"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3: Add missing barrier to 32bit version of gic_read_iar()
  irqchip/mxs: Add missing set_handle_irq()
  irqchip/gicv3-its: Avoid cache flush beyond ITS_BASERn memory size
  irqchip/gic-v3-its: Fix double ICC_EOIR write for LPI in EOImode==1

Pull staging/android fix from Greg KH:
 "Here is one patch, for the android binder driver, to resolve a
  reported problem.  Turns out it has been around for a while (since
  3.15), so it is good to finally get it resolved.

  It has been in linux-next for a while with no reported issues"

* tag 'staging-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  drivers: android: correct the size of struct binder_uintptr_t for BC_DEAD_BINDER_DONE

Pull USB fixes from Greg KH:
 "Here are a few USB fixes for 4.5-rc6

  They fix a reported bug for some USB 3 devices by reverting the recent
  patch, a MAINTAINERS change for some drivers, some new device ids, and
  of course, the usual bunch of USB gadget driver fixes.

  All have been in linux-next for a while with no reported issues"

* tag 'usb-4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  MAINTAINERS: drop OMAP USB and MUSB maintainership
  usb: musb: fix DMA for host mode
  usb: phy: msm: Trigger USB state detection work in DRD mode
  usb: gadget: net2280: fix endpoint max packet for super speed connections
  usb: gadget: gadgetfs: unregister gadget only if it got successfully registered
  usb: gadget: remove driver from pending list on probe error
  Revert "usb: hub: do not clear BOS field during reset device"
  usb: chipidea: fix return value check in ci_hdrc_pci_probe()
  usb: chipidea: error on overflow for port_test_write
  USB: option: add "4G LTE usb-modem U901"
  USB: cp210x: add IDs for GE B650V3 and B850V3 boards
  USB: option: add support for SIM7100E
  usb: musb: Fix DMA desired mode for Mentor DMA engine
  usb: gadget: fsl_qe_udc: fix IS_ERR_VALUE usage
  usb: dwc2: USB_DWC2 should depend on HAS_DMA
  usb: dwc2: host: fix the data toggle error in full speed descriptor dma
  usb: dwc2: host: fix logical omissions in dwc2_process_non_isoc_desc
  usb: dwc3: Fix assignment of EP transfer resources
  usb: dwc2: Add extra delay when forcing dr_mode

Pull vfs fixes from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  do_last(): ELOOP failure exit should be done after leaving RCU mode
  should_follow_link(): validate ->d_seq after having decided to follow
  namei: ->d_inode of a pinned dentry is stable only for positives
  do_last(): don't let a bogus return value from ->open() et.al. to confuse us
  fs: return -EOPNOTSUPP if clone is not supported
  hpfs: don't truncate the file when delete fails

Pull ARM SoC fixes from Olof Johansson:
 "We didn't have a batch last week, so this one is slightly larger.

  None of them are scary though, a handful of fixes for small DT pieces,
  replacing properties with newer conventions.

  Highlights:
   - N900 fix for setting system revision
   - onenand init fix to avoid filesystem corruption
   - Clock fix for audio on Beaglebone-x15
   - Fixes on shmobile to deal with CONFIG_DEBUG_RODATA (default y in 4.6)

  + misc smaller stuff"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  MAINTAINERS: Extend info, add wiki and ml for meson arch
  MAINTAINERS: alpine: add a new maintainer and update the entry
  ARM: at91/dt: fix typo in sama5d2 pinmux descriptions
  ARM: OMAP2+: Fix onenand initialization to avoid filesystem corruption
  Revert "regulator: tps65217: remove tps65217.dtsi file"
  ARM: shmobile: Remove shmobile_boot_arg
  ARM: shmobile: Move shmobile_smp_{mpidr, fn, arg}[] from .text to .bss
  ARM: shmobile: r8a7779: Remove remainings of removed SCU boot setup code
  ARM: shmobile: Move shmobile_scu_base from .text to .bss
  ARM: OMAP2+: Fix omap_device for module reload on PM runtime forbid
  ARM: OMAP2+: Improve omap_device error for driver writers
  ARM: DTS: am57xx-beagle-x15: Select SYS_CLK2 for audio clocks
  ARM: dts: am335x/am57xx: replace gpio-key,wakeup with wakeup-source property
  ARM: OMAP2+: Set system_rev from ATAGS for n900
  ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
  ARM: dts: kirkwood: use unique machine name for ds112
  ARM: dts: imx6: remove bogus interrupt-parent from CAAM node

... or we risk seeing a bogus value of d_is_symlink() there.

Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... otherwise d_is_symlink() above might have nothing to do with
the inode value we've got.

Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

both do_last() and walk_component() risk picking a NULL inode out
of dentry about to become positive, *then* checking its flags and
seeing that it's not negative anymore and using (already stale by
then) value they'd fetched earlier.  Usually ends up oopsing soon
after that...

Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>