Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.

While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.

This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.

However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.

Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.

Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.

Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The I2C's, MMC0 and MMC1 controllers have only one muxing option in the
SoC. In such a case, we can just move the muxing into the DTSI, and remove
it from the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The SRAM node in the A10s DTSI is empty, remove it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.

However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.

Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.

Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

There's no phandle pointing to the CMA pool, so it's label is unnecessary.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The CMA node has a unit address, but no reg property which generates a
warning in DTC. Change the node name to reflect its usage and drop the unit
address.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Our HDMI output endpoint on the A10s DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.

In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.

This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.

However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.

Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The interrupt-parent property is set in sun5i.dtsi, so there's no need to
repeat it.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Our main node for all the in-SoC controllers used to have a unit name. The
unit-name, in addition to being actually false, would not match any reg
property, which generates a warning.

Remove it in order to remove those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Using skeleton.dtsi will create a memory node that will generate a warning
in DTC. However, that node will be created by the bootloader, so we can
just remove it entirely in order to remove that warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Our oscillators clock names have a unit address, but no reg property, which
generates a warning in DTC. Change these names to remove those unit
addresses.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The simple-framebuffer nodes have a unit address, but no reg property which
generates a warning when compiling it with DTC.

Change the simple-framebuffer node names so that there is no warnings on
this anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Our HDMI output endpoint on the A10 DTSI has a warning under DTC: "graph
node has single child node 'endpoint', #address-cells/#size-cells are not
necessary". Fix this by removing those properties.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

Fix the 'unnecessary #address-cells/#size-cells without "ranges" or child
"reg" property' DTC warning for the gpio-keys DT node on A10 boards.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>

The lradc's analog reference voltage is set to 3.0 volt in the
hardware. This is more or less set in copper for at least lradc0. Set the
property in the dts to ensure the lradc is referenced properly.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

The T3/R40/V40 using the same sdk and config file in allwinner
sdk, it seem they are the same SOC just with different name, so
compatible with R40.

The t3-cqa3t-bv3 based on Allwinner T3 SoC, it has various connectors,
leds, buttons, and sell on:
https://item.taobao.com/item.htm?spm=2013.1.w4023-4203040713.25.62704cce7UCgLS&id=557154455330

It features:
 - X-Powers AXP221s PMIC connected to i2c0
 - 1/2 GB DDR3 DRAM
 - 8 GB eMMC
 - 2x USB 2.0 hosts
 - 1x USB 2.0 OTG
 - 2 LVDS connectors
 - 24 bit RGB LCD connector
 - HDMI output
 - DVP camera interface (support 500w cmos camera)
 - GPIO connectors
 - 5 TTL uarts and 2 RS232 uarts
 - 1 RS485 connector
 - support i2c capacitive tp and usb infrared tp
 - boot control, reset and user buttons
 - 3.5mm headphone and 3.5mm mic jack
 - 100M RJ45
 - micro SD card slot
 - DC power jack
 - RCT power slot
 - 1 CVBS TVIN
 - 1 CVBS TVOUT
 - 2 customer leds
 - 1 buzzer
 - 1 minipcie
 - I2C output
 - SPI output
 - PCM output
 - wifi and bt connector reserved.

Board info can find here:
https://github.com/Axl-zhang/Allwinner-V40-T3-R40-manualSigned-off-by: Hao Zhang <hao5781286@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Add Allwinner SoC T3 document and fix format.
Signed-off-by: Hao Zhang <hao5781286@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.

Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.

Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

The actual hardware has 4 data lines. Use them.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

Pull UBIFS updates from Richard Weinberger:

 - Full filesystem authentication feature, UBIFS is now able to have the
   whole filesystem structure authenticated plus user data encrypted and
   authenticated.

 - Minor cleanups

* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
  ubifs: Remove unneeded semicolon
  Documentation: ubifs: Add authentication whitepaper
  ubifs: Enable authentication support
  ubifs: Do not update inode size in-place in authenticated mode
  ubifs: Add hashes and HMACs to default filesystem
  ubifs: authentication: Authenticate super block node
  ubifs: Create hash for default LPT
  ubfis: authentication: Authenticate master node
  ubifs: authentication: Authenticate LPT
  ubifs: Authenticate replayed journal
  ubifs: Add auth nodes to garbage collector journal head
  ubifs: Add authentication nodes to journal
  ubifs: authentication: Add hashes to index nodes
  ubifs: Add hashes to the tree node cache
  ubifs: Create functions to embed a HMAC in a node
  ubifs: Add helper functions for authentication support
  ubifs: Add separate functions to init/crc a node
  ubifs: Format changes for authentication support
  ubifs: Store read superblock node
  ubifs: Drop write_node
  ...

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include:

  Bugfix:
   - Fix build issues on architectures that don't provide 64-bit cmpxchg

  Cleanups:
   - Fix a spelling mistake"

* tag 'nfs-for-4.20-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: fix spelling mistake, EACCESS -> EACCES
  SUNRPC: Use atomic(64)_t for seq_send(64)

Pull more timer updates from Thomas Gleixner:
 "A set of commits for the new C-SKY architecture timers"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings: timer: gx6605s SOC timer
  clocksource/drivers/c-sky: Add gx6605s SOC system timer
  dt-bindings: timer: C-SKY Multi-processor timer
  clocksource/drivers/c-sky: Add C-SKY SMP timer

Pull NTB updates from Jon Mason:
 "Fairly minor changes and bug fixes:

  NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
  private struct, and a few bug fixes"

* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
  ntb: idt: Alter the driver info comments
  ntb: idt: Discard temperature sensor IRQ handler
  ntb: idt: Add basic hwmon sysfs interface
  ntb: idt: Alter temperature read method
  ntb_netdev: Simplify remove with client device drvdata
  NTB: transport: Try harder to alloc an aligned MW buffer
  ntb: ntb_transport: Mark expected switch fall-throughs
  ntb: idt: Set PCIe bus address to BARLIMITx
  NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
  ntb: intel: fix return value for ndev_vec_mask()
  ntb_netdev: fix sleep time mismatch

Pull scheduler fixes from Ingo Molnar:
 "A memory (under-)allocation fix and a comment fix"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/topology: Fix off by one bug
  sched/rt: Update comment in pick_next_task_rt()

Pull x86 fixes from Ingo Molnar:
 "A number of fixes and some late updates:

   - make in_compat_syscall() behavior on x86-32 similar to other
     platforms, this touches a number of generic files but is not
     intended to impact non-x86 platforms.

   - objtool fixes

   - PAT preemption fix

   - paravirt fixes/cleanups

   - cpufeatures updates for new instructions

   - earlyprintk quirk

   - make microcode version in sysfs world-readable (it is already
     world-readable in procfs)

   - minor cleanups and fixes"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  compat: Cleanup in_compat_syscall() callers
  x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
  objtool: Support GCC 9 cold subfunction naming scheme
  x86/numa_emulation: Fix uniform-split numa emulation
  x86/paravirt: Remove unused _paravirt_ident_32
  x86/mm/pat: Disable preemption around __flush_tlb_all()
  x86/paravirt: Remove GPL from pv_ops export
  x86/traps: Use format string with panic() call
  x86: Clean up 'sizeof x' => 'sizeof(x)'
  x86/cpufeatures: Enumerate MOVDIR64B instruction
  x86/cpufeatures: Enumerate MOVDIRI instruction
  x86/earlyprintk: Add a force option for pciserial device
  objtool: Support per-function rodata sections
  x86/microcode: Make revision and processor flags world-readable

Pull perf updates and fixes from Ingo Molnar:
 "These are almost all tooling updates: 'perf top', 'perf trace' and
  'perf script' fixes and updates, an UAPI header sync with the merge
  window versions, license marker updates, much improved Sparc support
  from David Miller, and a number of fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
  perf intel-pt/bts: Calculate cpumode for synthesized samples
  perf intel-pt: Insert callchain context into synthesized callchains
  perf tools: Don't clone maps from parent when synthesizing forks
  perf top: Start display thread earlier
  tools headers uapi: Update linux/if_link.h header copy
  tools headers uapi: Update linux/netlink.h header copy
  tools headers: Sync the various kvm.h header copies
  tools include uapi: Update linux/mmap.h copy
  perf trace beauty: Use the mmap flags table generated from headers
  perf beauty: Wire up the mmap flags table generator to the Makefile
  perf beauty: Add a generator for MAP_ mmap's flag constants
  tools include uapi: Update asound.h copy
  tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
  tools include uapi: Update linux/fs.h copy
  perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
  perf cs-etm: Correct CPU mode for samples
  perf unwind: Take pgoff into account when reporting elf to libdwfl
  perf top: Do not use overwrite mode by default
  perf top: Allow disabling the overwrite mode
  perf trace: Beautify mount's first pathname arg
  ...

Pull irq fixes from Ingo Molnar:
 "An irqchip driver fix and a memory (over-)allocation fix"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
  irq/matrix: Fix memory overallocation