Add code in slot_complete_v2_hw() to deal with the slots which have
completed due to internal abort.

The status codes have the following meaning:

- STAT_IO_ABORTED: the IO has been aborted due to internal abort,
  whether by device or individual abort command

- STAT_IO_COMPLETE: internal abort command has completed successfully
  for device or individual abort command

- STAT_IO_NO_DEVICE: internal abort command has completed for device but
  cannot find any IO

- STAT_IO_NOT_VALID: internal abort command has completed for single
  command but could not find the command
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add function to prepare the an internal abort for v2 hw.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Execute an internal abort for executing a task abort.
This is for case of the command still being present
in host when abort is executed.

For a SATA internal abort, we set abort for all tasks
associated with the device.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Execute an internal abort for that device when it is removed, so that
commands for that device are not processed.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Add main code for internal abort functionality.

The internal abort features allows the host controller to abort commands
which are still active in the controller but have not yet been sent to
the slave device.

Typically a command only spends a relatively short time in the
controller when compared to the amount of the time after it is sent to
the slave device.

Two modes of internal abort are supported:

 - device
 - individual command

For device, when the internal abort is issued all commands in the host
for that device are aborted.  For a single command, only that command is
aborted if it is still in the host.

In HW the internal abort command is executed similar to any other sort
of command, like SSP.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

req_table is allocate by kzalloc, so we don't need to zero it again.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

We don't need to use kzalloc as we will always memset the
local_atto_ioctl later.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Driver version: 11.2.0.0
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Change the copyright to:
Copyright © xxxx - 2016 Broadcom

Update email.ids:
@avagotech.com - @broadcom.com
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Current EQ delay is set to 0 to receive very high max interrupt per sec.
Set EQ delay to 32 - reducing max interrupt rate from 65K to 20K per sec.

Set TCP connection window size to 64K with scale shift count 2.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

In very rare scenario, connection gets killed after throwing this error:
scsi host0: BM_2312 : Event CXN_KILLED_BAD_WRB_INDEX_ERROR[15]... CID : 4
connection1:0: detected conn error (1011)

memset ISCSI_WRB descriptor to zero for all allocations of WRB handle.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

BUG: unable to handle kernel NULL pointer dereference at 000000000000015e
IP: [<ffffffffa0081700>]
hwi_get_async_handle.isra.23.constprop.39+0x90/0x1d0 [be2iscsi]
PGD 0
Oops: 0000 [#1] SMP
...
Call Trace:
 <IRQ>
 [<ffffffffa00818bc>] hwi_process_default_pdu_ring+0x7c/0x280 [be2iscsi]
 [<ffffffffa0088f51>] beiscsi_process_cq+0x321/0xb90 [be2iscsi]
 [<ffffffff810af028>] ? __wake_up_common+0x58/0x90
 [<ffffffff810b0d84>] ? __wake_up+0x44/0x50
 [<ffffffffa0089a2d>] be_iopoll+0x1d/0xb0 [be2iscsi]
 [<ffffffff812d1f61>] blk_iopoll_softirq+0xc1/0x100
 [<ffffffff81084b0f>] __do_softirq+0xef/0x280

The symptom observed is multiple async handles get queued for same index
thus causing leak in buffers posted to FW.

The root cause is:
- async handle is continued to be used even if it does not match the
completion.
- list_move operation done on already filled index.

1. Remove use of writables, host_write_ptr and ep_read_ptr.
2. Remove consumed logic to update writables. Instead, use only
free_entries to do the accounting of handles to be posted back.
3. Remove busy_list, instead use simple slot to index handles.
4. Added check no data, header less and overflow to make sure
all async_handles are flushed in error cases.
5. Added code to verify gathering of handles to form PDU by
checking final bit before forwarding PDU.
6. Added code to catch mismatch with CQE and handle gracefully.
7. Use AMAP, traverse cri_wait_queue list to post buffers, log
"async PDU" related errors.
8. Rearranged few data structures and added comments in init &
processing path.
9. Added WARN_ONs to catch any HD ring corruption.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Driver unload should call COMMON_FUNCTION_RESET. For TPE feature, this
ensures that FW has knowledge about driver getting unloaded and can
reset its bit vector.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Sessions are no longer valid, so schedule sess_work to fail the sessions
immediately when error is detected. This is done to avoid iSCSI transport
layer to keep sending NOP-Out which driver any ways fail.

Schedule sess_work immediately in case of HBA error. Old sessions are gone
for good and need to be re-established.

iscsi_session_failure needs process context hence this work.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

After UE is detected, check for recoverable error by reading
SLIPORT SEMAPHORE register. If transient parity error i.e. 0xExxx
then schedule recovery work on driver wq.

FLag this error to prevent any transactions for the duration of ue2rp to
restart polling. After that, if FW becomes ready then recover port.

Wake up processes in wq before going offline.
Wait for process to execute before cleaning up.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

mgmt_epfw_cleanup does not implement v1 of OPCODE_COMMON_ISCSI_CLEANUP
IOCTL for SkyHawk.

Replace use of MCCQ with BMBX for issuing the IOCTL.
Remove be_mcc_compl_poll which is no longer needed.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

SLIPORT FUNCTION_RESET does not reset the chip.
So POST status needs to be checked before issuing FUNCTION_RESET.
The completion of FUNCTION_RESET is indicated in BMBX Rdy bit.

be_cmd_fw_initialize too needs to be done before issuing any cmd to FW.
be_cmd_fw_initialize is renamed as beiscsi_cmd_special_wrb.
Rearrange and rename few functions in init and cleanup path.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

beiscsi_fail_session is defined in be_cmds.c: move it to be_iscsi.c
Move card configuration commands to be_cmds.c.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

BE3 and SH cards can recover from transient parity errors treated
earlier as unrecoverable errors.

Add IOCTL to query FW support for this feature.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

UE detection in health check is done in a work scheduled in global wq.
UE caused due to transient parity errors are recoverable and reported
within 1s. If this check for TPE gets delayed, PF0 might initiate
soft-reset and then status of UE recoverable is lost.

Handle UE detection in timer routine. Move out EQ delay update work
from health check. Make the IOCTL for EQ delay update non-blocking
as the completion status is ignored.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Boot work involves:
1. Find and fetch configured boot session and its handle.
2. Attempt to open the session if its not.
3. Get the session details for boot kset creation.
4. Logout of that session owned by FW.
5. Create boot kset for session details.

All these actions were done in blocking call with retries in global wq.
Other works in wq suffered if the IOCTLs stalled or timed out.

This change moves all the boot work to make it non-blocking.
The work queued in global wq just issues the IOCTL depending on the action
to be taken and mcc wq schedules work depending on status of the IOCTL.
Initial boot_work is started on link and ASYNC event.

The other code changes move all boot related functions in one place and
follow naming conventions.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Save ue_detected and fw_timeout errors in state field of beiscsi_hba.
BEISCSI_HBA_RUNNING
BEISCSI_HBA_LINK_UP
BEISCSI_HBA_BOOT_FOUND
BEISCSI_HBA_PCI_ERR
BEISCSI_HBA_FW_TIMEOUT
BEISCSI_HBA_IN_UE

Make sure no PCI transaction happens once in error state.
Add checks in IO path to detect HBA in error.

Skip hwi_purge_eq step which can't be done in error state.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

todo_mcc_cq is not needed as only MCC work is queued.
todo_cq is not used at all.
Rename functions to be consistent.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

alloc_mcc_tag was replaced with alloc_mcc_wrb and is no more used.
beiscsi_pci_soft_reset is not used at all and won't be needed.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Redefine FW IP types.
Before issuing IOCTL to clear IP, check if IP is all zeroes.
All zeroes IP implies IP is not set in FW so FW fails that IOCTL.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Wrong settings displayed for iface:
iface.header_digest = 192.168.197.22
iface.data_digest = 255.255.255.0
iface.immediate_data = 192.168.197.1

Process ISCSI_NET_PARAM only in beiscsi_iface_get_param.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Rename mgmt_get_if_info to be consistent with APIs name.
Rename create/destroy APIs to indicate IFACE operations.
Remove legacy be2iscsi and use beiscsi.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Move mgmt_get_all_if_id before any set param operation.
Rename mgmt_get_all_if_id to beiscsi_if_get_handle.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

VLAN tag is L2 construct, move VLAN code out from configuring IP.
Rearrange and rename the APIs to make it consistent.
Replace ENOSYS with EPERM.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

If BOOTPROTO is changed to static, the DHCP IP address should be released.
All cases are being handled mgmt_set_ip and mgmt_static_ip_modify.

Rearrange IFACE APIs to:
beiscsi_if_clr_ip
beiscsi_if_set_ip
beiscsi_if_en_static
beiscsi_if_en_dhcp

This simplifies release of DHCP IP when BOOTPROTO is set to static.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Gateway APIs assume IP type as IPv4. Modify it to be generic to allow
clearing of IPv6 gateway set using BIOS.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

ipv4_iface and ipv6_iface fields need to be set to NULL when destroyed.
Before creation these are checked. Use these to report correct states.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Driver takes significant time to load 1m:20s and unload 40s.

Checkpatch script threw warning:
WARNING: msleep < 20ms can sleep for up to 20ms; see
Documentation/timers/timers-howto.txt

To eliminate this warning msleep(1) was replaced with msleep(20) before
submitting.

msleep(20) in init and uninit path for creation and destroying of number
of WRBQs, CQs, and EQs is adding to load/unload time.

Replace msleep with schedule_timeout_uninterruptible of 1ms as its
enough in most cases.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

This got unnecessarily introduced with other changes in previous
commits. mcc_lock is taken only in process contexts.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Following configuration is created with what driver exports:
iface.vlan_id = 65535
iface.vlan_priority = 255
iface.vlan_state = <empty>

vlan_state is empty as iscsiadm doesn't process "Disabled".
When applying this configuration, iscsiadm checks for if vlan_state is
"disable" if not it enables with value in vlan_id. 65535 not being valid
value, 0 is applied.

Use "enable" or "disable" for ISCSI_NET_PARAM.
Signed-off-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Provide a translation table between Ethernet and FC port speeds so odd
speeds (from a Ethernet POV) like 8 Gbit are correctly mapped to sysfs
and open-fcoe's fcoeadm.

Before:
    Description:      BCM57840 NetXtreme II 10/20-Gigabit Ethernet
    Revision:         11
    Manufacturer:     Broadcom Corporation
    Serial Number:    6CC2173EA1D0

    Driver:           bnx2x 1.712.30-0
    Number of Ports:  1

        Symbolic Name:     bnx2fc (QLogic BCM57840) v2.10.3 over eth2
        OS Device Name:    host1
        Node Name:         0x20006cc2173ea1d1
        Port Name:         0x10006cc2173ea1d1
        FabricName:        0x100000c0dd0ce717
        Speed:             unknown
        Supported Speed:   1 Gbit, 10 Gbit
        MaxFrameSize:      2048 bytes
        FC-ID (Port ID):   0x660702
        State:             Online

After:
    Description:      BCM57840 NetXtreme II 10/20-Gigabit Ethernet
    Revision:         11
    Manufacturer:     Broadcom Corporation
    Serial Number:    6CC2173EA1D0

    Driver:           bnx2x 1.712.30-0
    Number of Ports:  1

        Symbolic Name:     bnx2fc (QLogic BCM57840) v2.10.3 over eth2
        OS Device Name:    host1
        Node Name:         0x20006cc2173ea1d1
        Port Name:         0x10006cc2173ea1d1
        FabricName:        0x100000c0dd0ce717
        Speed:             8 Gbit
        Supported Speed:   1 Gbit, 10 Gbit
        MaxFrameSize:      2048 bytes
        FC-ID (Port ID):   0x660701
        State:             Online
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Update the block library link in the API documentation.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The adapter file descriptor was previously cached within the kernel for
a given context in order to support performing a close on behalf of an
application. This is no longer needed as applications are now required
to perform a close on the adapter file descriptor.
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Acked-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>