Pull more ACPI updates from Rafael Wysocki:
 "These update the ACPICA code in the kernel to the most recent upstream
  revision (which includes a regression fix and other improvements),
  make ACPICA clear the status of all ACPI events when entering sleep
  states (to restore the previous behavior) and update the ACPI
  operation region driver for the CrystalCove PMIC.

  Specifics:

   - Update the ACPICA code in the kernel to upstream revision 20180810
     including:
      * Fix for AML parser regression causing it to mishandle opcodes
        that open a scope upon parse failures (Erik Schmauss)
      * Fix for a reference counting issue on large systems (Erik
        Schmauss)
      * Fix to discard values coming from register reads that have
        failed (Erik Schmauss)
      * Two acpiexec fixes (Bob Moore, Erik Schmauss)
      * Debugger cleanup (Bob Moore)
      * Cleanup of duplicate table error message (Bob Moore)
      * Cleanup of hex detection in the utilities (Erik Schmauss)

   - Make ACPICA clear the status of all ACPI events when entering sleep
     states again to avoid functional regressions (Rafael Wysocki)

   - Update the ACPI operation region driver for the CrystalCove PMIC to
     cover all of the known operation region fields (Hans de Goede)"

* tag 'acpi-4.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PMIC: CrystalCove: Extend PMOP support to support all possible fields
  ACPICA: Clear status of all events when entering sleep states
  ACPICA: Update version to 20180810
  ACPICA: acpiexec: fix a small memory leak regression
  ACPICA: Reference Counts: increase max to 0x4000 for large servers
  ACPICA: Reference count: add additional debugging details
  ACPICA: acpi_exec: fixing -fi option
  ACPICA: Debugger: Cleanup interface to the AML disassembler
  ACPICA: AML Parser: skip opcodes that open a scope upon parse failure
  ACPICA: Utilities: split hex detection into smaller functions
  ACPICA: Update an error message for a duplicate table
  ACPICA: ACPICA: add status check for acpi_hw_read before assigning return value
  ACPICA: AML Parser: ignore all exceptions resulting from incorrect AML during table load

Pull more power management updates from Rafael Wysocki:
 "These fix the main idle loop and the menu cpuidle governor, clean up
  the latter, fix a mistake in the PCI bus type's support for system
  suspend and resume, fix the ondemand and conservative cpufreq
  governors, address a build issue in the system wakeup framework and
  make the ACPI C-states desciptions less confusing.

  Specifics:

   - Make the idle loop handle stopped scheduler tick correctly (Rafael
     Wysocki).

   - Prevent the menu cpuidle governor from letting CPUs spend too much
     time in shallow idle states when it is invoked with scheduler tick
     stopped and clean it up somewhat (Rafael Wysocki).

   - Avoid invoking the platform firmware to make the platform enter the
     ACPI S3 sleep state with suspended PCIe root ports which may
     confuse the firmware and cause it to crash (Rafael Wysocki).

   - Fix sysfs-related race in the ondemand and conservative cpufreq
     governors which may cause the system to crash if the governor
     module is removed during an update of CPU frequency limits (Henry
     Willard).

   - Select SRCU when building the system wakeup framework to avoid a
     build issue in it (zhangyi).

   - Make the descriptions of ACPI C-states vendor-neutral to avoid
     confusion (Prarit Bhargava)"

* tag 'pm-4.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpuidle: menu: Handle stopped tick more aggressively
  sched: idle: Avoid retaining the tick when it has been stopped
  PCI / ACPI / PM: Resume all bridges on suspend-to-RAM
  cpuidle: menu: Update stale polling override comment
  cpufreq: governor: Avoid accessing invalid governor_data
  x86/ACPI/cstate: Make APCI C1 FFH MWAIT C-state description vendor-neutral
  cpuidle: menu: Fix white space
  PM / sleep: wakeup: Fix build error caused by missing SRCU support

Pull IDE updates from David Miller:

 - Remove redundant variables (Colin Ian King)

 - Expected switch fall-through annotations (Gustavo A. R. Silva)

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
  ide: mark expected switch fall-throughs
  ide-tape: remove redundant variable buffer_size
  ide: remove redundant variables queue_run_ms and left

Pull sparc updates from David Miller:
 "Nothing super serious:

   - Convert sparc32 over to NO_BOOTMEM (Mike Rapoport)

   - Use dma_noncoherent_ops on sparc32 (Christoph Hellwig)

   - Fix kbuild defconfig handling on sparc32 (Masahiro Yamada)"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc: fix KBUILD_DEFCONFIG for ARCH=sparc32
  sparc32: split ramdisk detection and reservation to a helper function
  sparc32: switch to NO_BOOTMEM
  sparc: mm/init_32: kill trailing whitespace
  sparc: use generic dma_noncoherent_ops

Pull arch/h8300 updates from Yoshinori Sato.

* tag 'for-4.19' of git://git.sourceforge.jp/gitroot/uclinux-h8/linux:
  h8300: fix IRQ no
  arch/h8300: add a defconfig target
  arch/h8300: eliminate kgbd.c warning
  arch/h8300: eliminate ptrace.h warnings
  h8300:let the checker know that size_t is ulong
  h8300: Don't include linux/kernel.h in asm/atomic.h
  h8300: remove unnecessary of_platform_populate call
  h8300: Correct signature of test_bit()
  h8300: irqchip: fix warning
  h8300: switch to NO_BOOTMEM
  h8300: gcc-8.1 fix
  h8300: Add missing output register.

Old timer handler use 24 (Compare match A).
But current timer handler use 26 (Overflow).
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

Make the "defconfig" target valid for arch/h8300.  Currently
"make ARCH=h8300 defconfig" produces:

*** Can't find default configuration "arch/h8300/defconfig"!
../scripts/kconfig/Makefile:87: recipe for target 'defconfig' failed

By adding a value for KBUILD_DEFCONFIG, "make ARCH=h8300 defconfig"
successfully produces a kernel .config file:

*** Default configuration is based on 'edosk2674_defconfig'

This is useful for Kconfig editing/testing.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp (moderated for non-subscribers)
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

Drop the "const" qualifier from arch_kgdb_ops to eliminate the gcc
warning (gcc version is 8.1.0).

arch/h8300/kernel/kgdb.c:132:24: error: conflicting type qualifiers for 'arch_kgdb_ops'
 const struct kgdb_arch arch_kgdb_ops = {
In file included from ../arch/h8300/kernel/kgdb.c:12:
../include/linux/kgdb.h:284:26: note: previous declaration of 'arch_kgdb_ops' was here
 extern struct kgdb_arch  arch_kgdb_ops;
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

Add a "struct task_struct;" stub to arch/h8300's ptrace.h header to
eliminate gcc warnings (gcc version is 8.1.0).

../arch/h8300/include/asm/ptrace.h:32:34: warning: 'struct task_struct' declared inside parameter list will not be visible outside of this definition or declaration
 extern long h8300_get_reg(struct task_struct *task, int regno);
../arch/h8300/include/asm/ptrace.h:33:33: warning: 'struct task_struct' declared inside parameter list will not be visible outside of this definition or declaration
 extern int h8300_put_reg(struct task_struct *task, int regno,
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

All 64bit archs use unsigned long for size_t and most 32bit
archs use 'unsigned int'. By default, this is what is assumed
by sparse.

However, on h8300 (a 32bit arch) size_t is unsigned long which
can led sparse to emit wrong warnings.

Fix this by passing to sparse the flag -msize-long, telling it
that size_t is unsigned long.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

linux/kernel.h isn't needed by asm/atomic.h and will result in circular
dependencies when the asm-generic atomic bitops are built around the
tomic_long_t interface.

Remove the broad include and replace it with linux/compiler.h for
READ_ONCE etc and asm/irqflags.h for arch_local_irq_save etc.

Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

The DT core will call of_platform_populate, so it is not necessary for
arch specific code to call it unless there are custom match entries,
auxdata or parent device. Neither of those apply here, so remove the call.

Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

    mm/filemap.c: In function 'clear_bit_unlock_is_negative_byte':
    mm/filemap.c:1181:30: warning: passing argument 2 of 'test_bit' discards 'volatile' qualifier from pointer target type [-Wdiscarded-qualifiers]
      return test_bit(PG_waiters, mem);
				  ^~~
    In file included from include/linux/bitops.h:38,
		     from include/linux/kernel.h:11,
		     from include/linux/list.h:9,
		     from include/linux/wait.h:7,
		     from include/linux/wait_bit.h:8,
		     from include/linux/fs.h:6,
		     from include/linux/dax.h:5,
		     from mm/filemap.c:14:
    arch/h8300/include/asm/bitops.h:69:57: note: expected 'const long unsigned int *' but argument is of type 'volatile void *'
     static inline int test_bit(int nr, const unsigned long *addr)
					~~~~~~~~~~~~~~~~~~~~~^~~~

Make the bitmask pointed to by the "addr" parameter volatile to fix
this, like is done on other architectures.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

Var "addr" type incorrect.
It have interrupt controler register address.
Type of void __iomem is correct.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

Commit 0fa1c579 ("of/fdt: use memblock_virt_alloc for early alloc")
inadvertently switched the DT unflattening allocations from memblock to
bootmem which doesn't work because the unflattening happens before
bootmem is initialized. Swapping the order of bootmem init and
unflattening could also fix this, but removing bootmem is desired. So
enable NO_BOOTMEM on h8300 like other architectures have done.

Fixes: 0fa1c579 ("of/fdt: use memblock_virt_alloc for early alloc")
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: uclinux-h8-devel@lists.sourceforge.jp
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

Since gcc 8.1 does not generate an assignment statement to er 0,
we had to explicitly write it.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>

Pull fuse update from Miklos Szeredi:
 "Various bug fixes and cleanups"

* tag 'fuse-update-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: reduce allocation size for splice_write
  fuse: use kvmalloc to allocate array of pipe_buffer structs.
  fuse: convert last timespec use to timespec64
  fs: fuse: Adding new return type vm_fault_t
  fuse: simplify fuse_abort_conn()
  fuse: Add missed unlock_page() to fuse_readpages_fill()
  fuse: Don't access pipe->buffers without pipe_lock()
  fuse: fix initial parallel dirops
  fuse: Fix oops at process_init_reply()
  fuse: umount should wait for all requests
  fuse: fix unlocked access to processing queue
  fuse: fix double request_end()

Pull overlayfs updates from Miklos Szeredi:
 "This contains two new features:

   - Stack file operations: this allows removal of several hacks from
     the VFS, proper interaction of read-only open files with copy-up,
     possibility to implement fs modifying ioctls properly, and others.

   - Metadata only copy-up: when file is on lower layer and only
     metadata is modified (except size) then only copy up the metadata
     and continue to use the data from the lower file"

* tag 'ovl-update-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs: (66 commits)
  ovl: Enable metadata only feature
  ovl: Do not do metacopy only for ioctl modifying file attr
  ovl: Do not do metadata only copy-up for truncate operation
  ovl: add helper to force data copy-up
  ovl: Check redirect on index as well
  ovl: Set redirect on upper inode when it is linked
  ovl: Set redirect on metacopy files upon rename
  ovl: Do not set dentry type ORIGIN for broken hardlinks
  ovl: Add an inode flag OVL_CONST_INO
  ovl: Treat metacopy dentries as type OVL_PATH_MERGE
  ovl: Check redirects for metacopy files
  ovl: Move some dir related ovl_lookup_single() code in else block
  ovl: Do not expose metacopy only dentry from d_real()
  ovl: Open file with data except for the case of fsync
  ovl: Add helper ovl_inode_realdata()
  ovl: Store lower data inode in ovl_inode
  ovl: Fix ovl_getattr() to get number of blocks from lower
  ovl: Add helper ovl_dentry_lowerdata() to get lower data dentry
  ovl: Copy up meta inode data from lowest data inode
  ovl: Modify ovl_lookup() and friends to lookup metacopy dentry
  ...

Pull xfs fixes from Darrick Wong:

 - Fix an uninitialized variable

 - Don't use obviously garbage AG header counters to calculate
   transaction reservations

 - Trigger icount recalculation on bad icount when mounting

* tag 'xfs-4.19-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  iomap: fix WARN_ON_ONCE on uninitialized variable
  xfs: sanity check ag header values in xrep_calc_ag_resblks
  xfs: recalculate summary counters at mount time if icount is bad

Pull power supply and reset updates from Sebastian Reichel:

 - Improve support for TI bq20z75 in sbs-battery

 - Add Qualcomm PM8xxx reboot driver

 - Add cros-ec USBPD charger driver

 - Move ds2760 battery driver from w1 to power-supply and add DT support

 - Misc fixes

* tag 'for-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (28 commits)
  power: supply: bq27xxx: Update comments
  power: supply: max77693_charger: fix unintentional fall-through
  power: supply: mark expected switch fall-throughs
  power: supply: lego_ev3_battery: fix Vce offset
  power: supply: lego_ev3_battery: Don't ignore iio_read_channel_processed() return value
  power: supply: ds2760_battery: add devicetree probing
  power: supply: ds2760_battery: merge ds2760 supply driver with its w1 slave companion
  w1: core: match sub-nodes of bus masters in devicetree
  dt-bindings: w1: document bindings for ds2760 battery monitor
  dt-bindings: w1: document generic onewire bindings
  power: supply: adp5061: Fix a couple off by ones
  dt-bindings: power: reset: qcom: Add resin binding
  adp5061: New driver for ADP5061 I2C battery charger
  power: generic-adc-battery: check for duplicate properties copied from iio channels
  power: generic-adc-battery: fix out-of-bounds write when copying channel properties
  power: supply: axp288_charger: Fix initial constant_charge_current value
  power: supply: ab8500: stop using getnstimeofday64()
  power: gemini-poweroff: Avoid more spurious poweroffs
  power: vexpress: fix corruption in notifier registration
  power: remove possible deadlock when unregistering power_supply
  ...

Pull i2c updates from Wolfram Sang:

 - the core has now a lockless variant of i2c_smbus_xfer. Some open
   coded versions of this got removed in drivers. This also enables
   proper SCCB support in regmap.

 - locking got a more precise naming. i2c_{un}lock_adapter() had to go,
   and we know use i2c_lock_bus() consistently with flags like
   I2C_LOCK_ROOT_ADAPTER and I2C_LOCK_SEGMENT to avoid ambiguity.

 - the gpio fault injector got a new delicate testcase

 - the bus recovery procedure got fixed to handle the new testcase
   correctly

 - a new quirk flag for controllers not able to handle zero length
   messages together with driver updates to use it

 - new drivers: FSI bus attached I2C masters, GENI I2C controller, Owl
   family S900

 - and a good set of driver improvements and bugfixes

* 'i2c/for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (77 commits)
  i2c: rcar: implement STOP and REP_START according to docs
  i2c: rcar: refactor private flags
  i2c: core: ACPI: Make acpi_gsb_i2c_read_bytes() check i2c_transfer return value
  i2c: core: ACPI: Properly set status byte to 0 for multi-byte writes
  dt-bindings: i2c: rcar: Add r8a774a1 support
  dt-bindings: i2c: sh_mobile: Add r8a774a1 support
  i2c: imx: Simplify stopped state tracking
  i2c: imx: Fix race condition in dma read
  i2c: pasemi: remove hardcoded bus numbers on smbus
  i2c: designware: Add SPDX license tag
  i2c: designware: Convert to use struct i2c_timings
  i2c: core: Parse SDA hold time from firmware
  i2c: designware-pcidrv: Mark expected switch fall-through
  i2c: amd8111: Mark expected switch fall-through
  i2c: sh_mobile: use core to detect 'no zero length read' quirk
  i2c: xlr: use core to detect 'no zero length' quirk
  i2c: rcar: use core to detect 'no zero length' quirk
  i2c: stu300: use core to detect 'no zero length' quirk
  i2c: pmcmsp: use core to detect 'no zero length' quirk
  i2c: mxs: use core to detect 'no zero length' quirk
  ...

Merge branch 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace

Pull core signal handling updates from Eric Biederman:
 "It was observed that a periodic timer in combination with a
  sufficiently expensive fork could prevent fork from every completing.
  This contains the changes to remove the need for that restart.

  This set of changes is split into several parts:

   - The first part makes PIDTYPE_TGID a proper pid type instead
     something only for very special cases. The part starts using
     PIDTYPE_TGID enough so that in __send_signal where signals are
     actually delivered we know if the signal is being sent to a a group
     of processes or just a single process.

   - With that prep work out of the way the logic in fork is modified so
     that fork logically makes signals received while it is running
     appear to be received after the fork completes"

* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (22 commits)
  signal: Don't send signals to tasks that don't exist
  signal: Don't restart fork when signals come in.
  fork: Have new threads join on-going signal group stops
  fork: Skip setting TIF_SIGPENDING in ptrace_init_task
  signal: Add calculate_sigpending()
  fork: Unconditionally exit if a fatal signal is pending
  fork: Move and describe why the code examines PIDNS_ADDING
  signal: Push pid type down into complete_signal.
  signal: Push pid type down into __send_signal
  signal: Push pid type down into send_signal
  signal: Pass pid type into do_send_sig_info
  signal: Pass pid type into send_sigio_to_task & send_sigurg_to_task
  signal: Pass pid type into group_send_sig_info
  signal: Pass pid and pid type into send_sigqueue
  posix-timers: Noralize good_sigevent
  signal: Use PIDTYPE_TGID to clearly store where file signals will be sent
  pid: Implement PIDTYPE_TGID
  pids: Move the pgrp and session pid pointers from task_struct to signal_struct
  kvm: Don't open code task_pid in kvm_vcpu_ioctl
  pids: Compute task_tgid using signal->leader_pid
  ...

Merge fixes for the ondemand and conservative cpufreq governors,
PCI power management and system wakeup framework.

* pm-cpufreq:
  cpufreq: governor: Avoid accessing invalid governor_data

* pm-pci:
  PCI / ACPI / PM: Resume all bridges on suspend-to-RAM

* pm-sleep:
  PM / sleep: wakeup: Fix build error caused by missing SRCU support

Merge a CrystalCove PMIC driver update.

* acpi-pmic:
  ACPI / PMIC: CrystalCove: Extend PMOP support to support all possible fields

Merge tag 'chrome-platform-for-linus-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform

Pull chrome platform updates from Benson Leung.

Everything but the SPDX identifier updates actually came in earlier
through the MFD merge.

* tag 'chrome-platform-for-linus-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
  platform/chrome: chromeos_tbmc - fix SPDX identifier

Pull arch/microblaze updates from Michal Simek:

 - use generic noncoherent direct mapping

 - use LDFLAGS instead of LD

 - pci error path fix

 - remove incorrect comments

* tag 'microblaze-v4.19-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze/PCI: Remove stale pcibios_align_resource() comment
  microblaze: delete wrong comment about machine_early_init
  microblaze: add endianness options to LDFLAGS instead of LD
  microblaze: remove consistent_sync and consistent_sync_page
  microblaze: use generic dma_noncoherent_ops
  microblaze: warn if of_iomap() failed

As commit 5ba80096 ("kbuild: update ARCH alias info for sparc")
addressed, SPARC accepts ARCH=sparc32 as an alias.

However, arch/sparc/Makefile wrongly sets KBUILD_DEFCONFIG, then
sparc64_defconfig is chosen as the base configuration for ARCH=sparc32.

  $ make ARCH=sparc32 defconfig
  *** Default configuration is based on 'sparc64_defconfig'
  #
  # configuration written to .config
  #

Fix the logic to choose sparc64_defconfig only when ARCH=sparc64.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mike Rapoport says:

====================
sparc32: switch to NO_BOOTMEM

These patches convert sparc32 to use memblock + nobootmem.
I've made the conversion as simple as possible, just enough to allow moving
HAVE_MEMBLOCK and NO_BOOTMEM to the common SPARC configuration.

v2 changes:
* split whitespace changes to a separate patch
* address Sam's comments [1]

[1] https://lkml.org/lkml/2018/8/2/403
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The detection and reservation of ramdisk memory were separated to allow
bootmem bitmap initialization after the ramdisk boundaries are detected.
Since the bootmem initialization is removed, the reservation of ramdisk
memory is done immediately after its boundaries are found.

Split the entire block into a separate helper function.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each populated sparc_phys_bank is added to memblock.memory. The
reserve_bootmem() calls are replaced with memblock_reserve(), and the
bootmem bitmap initialization is droppped.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Switch to the generic noncoherent direct mapping implementation.

This removes the previous sync_single_for_device implementation, which
looks bogus given that no syncing is happening in the similar but more
important map_single case.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 01cf9d52 ("microblaze/PCI: Support generic Xilinx AXI PCIe Host
Bridge IP driver")

and

commit ecf677c8 ("PCI: Add a generic weak pcibios_align_resource()")

first patched then removed pcibios_align_resource() from the microblaze
architecture code but failed to remove the comment that was added to
it.

Remove it since it has now become stale and it is quite confusing.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bharat Kumar Gogada <bharatku@xilinx.com>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Pull ia64 NO_BOOTMEM conversion from Tony Luck:
 "Mike Rapoport kindly fixed up ia64 to work with NO_BOOTMEM"

* tag 'please-pull-noboot' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  ia64: switch to NO_BOOTMEM
  ia64: use mem_data to detect nodes' minimal and maximal PFNs
  ia64: remove unused num_dma_physpages member from 'struct early_node_data'
  ia64: contig/paging_init: reduce code duplication

Merge tag 'linux-kselftest-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest update from Shuah Khan:

 - add cgroup core selftests

 - fix compile warnings in android ion test

 - fix to bugs in exclude and skip paths in vDSO test

 - remove obsolete config options

 - add missing .gitignore file

* tag 'linux-kselftest-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/ftrace: Fix kprobe string testcase to not probe notrace function
  selftests: mount: remove no longer needed config option
  selftests: cgroup: add gitignore file
  Add cgroup core selftests
  selftests: vDSO - fix to return KSFT_SKIP when test couldn't be run
  selftests: vDSO - fix to exclude x86 test on non-x86 platforms
  selftests/android: initialize heap_type to avoid compiling warning

Pull tracing updates from Steven Rostedt:

 - Restructure of lockdep and latency tracers

   This is the biggest change. Joel Fernandes restructured the hooks
   from irqs and preemption disabling and enabling. He got rid of a lot
   of the preprocessor #ifdef mess that they caused.

   He turned both lockdep and the latency tracers to use trace events
   inserted in the preempt/irqs disabling paths. But unfortunately,
   these started to cause issues in corner cases. Thus, parts of the
   code was reverted back to where lockdep and the latency tracers just
   get called directly (without using the trace events). But because the
   original change cleaned up the code very nicely we kept that, as well
   as the trace events for preempt and irqs disabling, but they are
   limited to not being called in NMIs.

 - Have trace events use SRCU for "rcu idle" calls. This was required
   for the preempt/irqs off trace events. But it also had to not allow
   them to be called in NMI context. Waiting till Paul makes an NMI safe
   SRCU API.

 - New notrace SRCU API to allow trace events to use SRCU.

 - Addition of mcount-nop option support

 - SPDX headers replacing GPL templates.

 - Various other fixes and clean ups.

 - Some fixes are marked for stable, but were not fully tested before
   the merge window opened.

* tag 'trace-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (44 commits)
  tracing: Fix SPDX format headers to use C++ style comments
  tracing: Add SPDX License format tags to tracing files
  tracing: Add SPDX License format to bpf_trace.c
  blktrace: Add SPDX License format header
  s390/ftrace: Add -mfentry and -mnop-mcount support
  tracing: Add -mcount-nop option support
  tracing: Avoid calling cc-option -mrecord-mcount for every Makefile
  tracing: Handle CC_FLAGS_FTRACE more accurately
  Uprobe: Additional argument arch_uprobe to uprobe_write_opcode()
  Uprobes: Simplify uprobe_register() body
  tracepoints: Free early tracepoints after RCU is initialized
  uprobes: Use synchronize_rcu() not synchronize_sched()
  tracing: Fix synchronizing to event changes with tracepoint_synchronize_unregister()
  ftrace: Remove unused pointer ftrace_swapper_pid
  tracing: More reverting of "tracing: Centralize preemptirq tracepoints and unify their usage"
  tracing/irqsoff: Handle preempt_count for different configs
  tracing: Partial revert of "tracing: Centralize preemptirq tracepoints and unify their usage"
  tracing: irqsoff: Account for additional preempt_disable
  trace: Use rcu_dereference_raw for hooks from trace-event subsystem
  tracing/kprobes: Fix within_notrace_func() to check only notrace functions
  ...

Pull ceph updates from Ilya Dryomov:
 "The main things are support for cephx v2 authentication protocol and
  basic support for rbd images within namespaces (myself).

  Also included are y2038 conversion patches from Arnd, a pile of
  miscellaneous fixes from Chengguang and Zheng's feature bit
  infrastructure for the filesystem"

* tag 'ceph-for-4.19-rc1' of git://github.com/ceph/ceph-client: (40 commits)
  ceph: don't drop message if it contains more data than expected
  ceph: support cephfs' own feature bits
  crush: fix using plain integer as NULL warning
  libceph: remove unnecessary non NULL check for request_key
  ceph: refactor error handling code in ceph_reserve_caps()
  ceph: refactor ceph_unreserve_caps()
  ceph: change to void return type for __do_request()
  ceph: compare fsc->max_file_size and inode->i_size for max file size limit
  ceph: add additional size check in ceph_setattr()
  ceph: add additional offset check in ceph_write_iter()
  ceph: add additional range check in ceph_fallocate()
  ceph: add new field max_file_size in ceph_fs_client
  libceph: weaken sizeof check in ceph_x_verify_authorizer_reply()
  libceph: check authorizer reply/challenge length before reading
  libceph: implement CEPHX_V2 calculation mode
  libceph: add authorizer challenge
  libceph: factor out encrypt_authorizer()
  libceph: factor out __ceph_x_decrypt()
  libceph: factor out __prepare_write_connect()
  libceph: store ceph_auth_handshake pointer in ceph_connection
  ...

Pull RTC updates from Alexandre Belloni:
 "It is now possible to add custom sysfs attributes while avoiding a
  possible race condition. Unused code has been removed resulting in a
  nice reduction of the code base. And more drivers have been switched
  to SPDX by their maintainers.

 Summary:

  Subsystem:
   - new helpers to add custom sysfs attributes
   - struct rtc_task removal along with rtc_irq_[un]register()
   - rtc_irq_set_state and rtc_irq_set_freq are not exported anymore

  Drivers:
   - armada38x: reset after rtc power loss
   - ds1307: now supports m41t11
   - isl1208: now supports isl1219 and tamper detection
   - pcf2127: internal SRAM support"

* tag 'rtc-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (34 commits)
  rtc: ds1307: simplify hwmon config
  rtc: s5m: Add SPDX license identifier
  rtc: maxim: Add SPDX license identifiers
  rtc: isl1219: add device tree documentation
  rtc: isl1208: set ev-evienb bit from device tree
  rtc: isl1208: Add "evdet" interrupt source for isl1219
  rtc: isl1208: add support for isl1219 with tamper detection
  rtc: sysfs: facilitate attribute add to rtc device
  rtc: remove struct rtc_task
  char: rtc: remove task handling
  rtc: pcf85063: preserve control register value between stop and start
  rtc: sh: remove unused variable rtc_dev
  rtc: unexport rtc_irq_set_*
  rtc: simplify rtc_irq_set_state/rtc_irq_set_freq
  rtc: remove irq_task and irq_task_lock
  rtc: remove rtc_irq_register/rtc_irq_unregister
  rtc: sh: remove dead code
  rtc: sa1100: don't set PIE frequency
  rtc: ds1307: support m41t11 variant
  rtc: ds1307: fix data pointer to m41t0
  ...

Pull livepatching updates from Jiri Kosina:
 "Code cleanups from Kamalesh Babulal"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/livepatching:
  livepatch: Validate module/old func name length
  livepatch: Remove reliable stacktrace check in klp_try_switch_task()