- 31 Mar, 2010 40 commits
-
-
Stanislaw Gruszka authored
Add interface to disable/enable QoS (aka WMM or WME). Currently drivers enable it explicitly when ->conf_tx method is called, and newer disable. Disabling is needed for some APs, which do not support QoS, such we should send QoS frames to them. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Zhu Yi authored
Remove skb_linearize() in the iwlwifi drivers since mac80211 supports paged rx SKBs now. Signed-off-by:
Zhu Yi <yi.zhu@intel.com> Signed-off-by:
-
Zhu Yi authored
Mac80211 drivers can now pass paged SKBs to mac80211 via ieee80211_rx{_irqsafe}. The implementation currently use skb_linearize() in a few places i.e. management frame handling, software decryption, defragmentation and A-MSDU process. We will optimize them one by one later. Signed-off-by: -
Rafał Miłecki authored
Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
We do not want to partially change chanspec just to find out there is not entry in table for given channel. Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Rafał Miłecki authored
Signed-off-by:
-
Xose Vazquez Perez authored
Taken from latest ralink linux driver(RT3070_LinuxSTA_V2.3.0.1_20100208) All of them are RT3070 devices. Signed-off-by:
Xose Vazquez Perez <xose.vazquez@gmail.com> Acked-by:
Ivo van Doorn <IvDoorn@gmail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
-
Xose Vazquez Perez authored
Taken from latest ralink linux driver, it's a RT3593 PCI/PCIe. Signed-off-by:
-
Xose Vazquez Perez authored
It was removed in the windows inf file by ralink. And it isn't on ralink linux drivers. Signed-off-by:
-
Xose Vazquez Perez authored
Taken from ralink linux drivers: RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0B05,0x1784)}, /* Asus 3072 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x13D3,0x3305)}, /* AzureWave 3070*/ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x07D1,0x3C16)}, /* D-Link 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x203D,0x14A9)}, /* Encore 3070*/ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x1740,0x9707)}, /* EnGenius 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x1740,0x9708)}, /* EnGenius 3071 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x1740,0x9709)}, /* EnGenius 3072 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x04BB,0x0947)}, /* I-O DATA 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x04BB,0x0948)}, /* I-O DATA 3072 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x3822)}, /* MSI 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x3821)}, /* Ralink 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x3870)}, /* MSI 3070*/ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x3871)}, /* MSI 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x821A)}, /* Ralink 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x822A)}, /* MSI 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x870A)}, /* MSI 3070*/ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x871A)}, /* MSI 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DB0,0x899A)}, /* MSI 3070*/ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x20B8,0x8888)}, /* PARA INDUSTRIAL 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DF6,0x0048)}, /* Sitecom 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x0DF6,0x0047)}, /* Sitecom 3071 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x083A,0xA701)}, /* SMC 3070 */ RT3070_LinuxSTA_V2.3.0.1_20100208/common/rtusb_dev_id.c: {USB_DEVICE(0x083A,0xA702)}, /* SMC 3072 */ Signed-off-by: -
Saravanan Dhanabal authored
After last transmission, the device goes to sleep earlier than the configured dynamic power save timeout. If timeout is set to 400ms, device enters into sleep mode at around 330ms since from last TX. This patch removes the msleep(1), which causes the delay after ELP wakeup. Replaced with udelay(10), the variation is around 7-10ms. Signed-off-by:
Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com> Reviewed-by:
Juuso Oikarinen <juuso.oikarinen@nokia.com> Signed-off-by:
Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by:
-
Juuso Oikarinen authored
This patch will enable the hardware keep-alive mode, configure the required template, configure keep-alive parameters, and re-order JOIN's and ACX_AID in such a way that the keep-alive is activated. Signed-off-by:
-
Juuso Oikarinen authored
Add support for keep-alive templates, which are indexed. Signed-off-by:
-
Juuso Oikarinen authored
This patch configures the mac80211 to not perform connection monitoring (periodic probe-requests) and instead rely on the hardware to do it. Signed-off-by:
-
Juuso Oikarinen authored
If PSM entry fails despite of retries, assume that the AP has been lost, and indicate connection loss to the mac80211. This is much safer than remaining in active mode. Signed-off-by:
-
Juuso Oikarinen authored
Configure a probe-request template to the wl1271 when associated - the wl1271 will use this to attempt to recover a connection when beacon loss is detected. Signed-off-by:
-
Juuso Oikarinen authored
The driver tx-queue flush operation leaks broadcast-frames. This leak occurs if the driver is shut down while there are frames in TX buffers (such as in a firmware crash scenario.) Fix the leak. Signed-off-by:
Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com> Signed-off-by:
-
Teemu Paasikivi authored
Change the driver to call ieee80211_beacon_loss function always when BSS_LOST_EVENT is received. Reason for the change is that entering PSM might fail before driver receives BSS_LOST_EVENT. In such case the driver would disable PSM and the stack would not be notified about beacon loss and connection loss detection would be delayed by tens of seconds. Signed-off-by:
-
Juuso Oikarinen authored
Configure the hardware beacon interval to whatever requested by the mac80211. Signed-off-by:
-
Juuso Oikarinen authored
Fix the driver to better reflect the ad-hoc related configuration from the mac80211. Signed-off-by:
-
Juuso Oikarinen authored
The wl1271 does not support disabling the connection monitor feature. Perform the next best thing by increasing the beacon-loss threshold and BSS_LOSE event timeout to the maximum values. This is needed, because we really don't want any random probe-requests during scanning or especially while in ad-hoc mode and not beaconing. Signed-off-by:
-
Luciano Coelho authored
The noise element in the ieee80211_rx_status struct has been deprecated in commit "mac80211: deprecate RX status noise". Remove the usage of this element from wl1271_rx.c to avoid warnings. Signed-off-by:
-
Luciano Coelho authored
Wait for the DISCONNECT_EVENT_COMPLETE_ID event after sending a disconnect command. Signed-off-by:
-
Luciano Coelho authored
Poll for join command completion instead of waiting blindly for 10 msecs. There is a timeout of 100 msecs, if the command doesn't complete by then, we return an error code. Signed-off-by:
-
Juuso Oikarinen authored
This patch removes the MAC address randomization from the driver. This removes a nasty Nokia-OUI dependency from the driver. With this patch, unless an address is explicitly configured to the driver by the user, only a zero address will be configured, and the driver will be unable to start. Signed-off-by:
-
Juuso Oikarinen authored
After the busy-words, if the firmware did not complete by the end of the first (fixed) busy-word, a flip of the CS line is required to enable clocking out the actual read data. This patch changes the mechanism such that the CS line is flipped after each busyword. Also, the busy-word mechanism is finally enabled, and the number of fixed busywords reduced to the minimum. Signed-off-by:
-
Juuso Oikarinen authored
Fix a trivial memory leak in cmd_data_path. Signed-off-by:
-
Teemu Paasikivi authored
There were wrong format specifiers in wl1271_sdio.c in some debug outputs. This has been causing warnings on some platforms. Signed-off-by:
-
Juuso Oikarinen authored
This patch configures the wl1271 chipset clock-request line to be driver in open-drain mode instead of push-pull. Signed-off-by:
-
Juuso Oikarinen authored
This patch fixes a memory leak in the scan command handling code. Signed-off-by:
Kalle Valo <kalle.valo@iki.fi> Signed-off-by:
-
Juuso Oikarinen authored
This patch fixes two memory leaks in the SPI initialization code. Signed-off-by:
-
Juuso Oikarinen authored
Add reporting of the used TX rate to mac80211 in the tx_status. Signed-off-by:
Kalle Valo <kalle.valo@nokia.com> Signed-off-by:
-
Juuso Oikarinen authored
Clean up the code to convert a firmware rate class index into an index for the rate configuration table. Signed-off-by:
-
Luciano Coelho authored
When forward porting some patches to upstream, there was a mistake and the wl1271_spi driver name remained, erroneously, as "wl1271". This patch fixes that. Signed-off-by:
-
Bruno Randolf authored
Chipsets since revision AR5213A (0x59) have hardware counters for PHY errors which we can read directly from the registers. Older hardware has to use the RX descriptor status to get a count of PHY errors. This will be used in several places in the ANI implementation, so a flag is useful. Signed-off-by:
Bruno Randolf <br1@einfach.org> Signed-off-by:
-
Bruno Randolf authored
Update PHY error codes from the HAL, and keep them in statistics for debugging via the 'frameerrors' file. This will also be used by ANI. Signed-off-by:
-
Bruno Randolf authored
Let's keep MIB counter statistics in our own statistics structure and only convert it to ieee80211_low_level_stats when needed by mac80211. Also we don't need to read profile count registers in the MIB interrupt (they don't trigger MIB interrupts). Signed-off-by:
-
Bruno Randolf authored
Initialize noise floor variable with a default of -95. This was used uninitialized in the signal strength (RSSI -> dBm) conversion until the first noise floor calibration was completed. Signed-off-by:
-
