The same message "qp %d: Link Down\n" was printed at two locations in
ntb_transport.  Change the messages so they are distinct.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Set errata flags for the specific device IDs to which they apply,
instead of the whole Xeon hardware class.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen.  Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The transport was writing and then reading the peer scratch pad,
essentially reading what it just wrote instead of exchanging any
information with the peer.  The transport expects the peer values to be
the same as the local values, so this issue was not obvious.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Change ntb_hw_intel to use the new NTB hardware abstraction layer.

Split ntb_transport into its own driver.  Change it to use the new NTB
hardware abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Abstract the NTB device behind a programming interface, so that it can
support different hardware and client drivers.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer.  Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Pull PCI updates from Bjorn Helgaas:
 "PCI changes for the v4.2 merge window:

  Enumeration
    - Move pci_ari_enabled() to global header (Alex Williamson)
    - Account for ARI in _PRT lookups (Alex Williamson)
    - Remove unused pci_scan_bus_parented() (Yijing Wang)

  Resource management
    - Use host bridge _CRS info on systems with >32 bit addressing (Bjorn Helgaas)
    - Use host bridge _CRS info on Foxconn K8M890-8237A (Bjorn Helgaas)
    - Fix pci_address_to_pio() conversion of CPU address to I/O port (Zhichang Yuan)
    - Add pci_bus_addr_t (Yinghai Lu)

  PCI device hotplug
    - Wait for pciehp command completion where necessary (Alex Williamson)
    - Drop pointless ACPI-based "slot detection" check (Rafael J. Wysocki)
    - Check ignore_hotplug for all downstream devices (Rafael J. Wysocki)
    - Propagate the "ignore hotplug" setting to parent (Rafael J. Wysocki)
    - Inline pciehp "handle event" functions into the ISR (Bjorn Helgaas)
    - Clean up pciehp debug logging (Bjorn Helgaas)

  Power management
    - Remove redundant PCIe port type checking (Yijing Wang)
    - Add dev->has_secondary_link to track downstream PCIe links (Yijing Wang)
    - Use dev->has_secondary_link to find downstream links for ASPM (Yijing Wang)
    - Drop __pci_disable_link_state() useless "force" parameter (Bjorn Helgaas)
    - Simplify Clock Power Management setting (Bjorn Helgaas)

  Virtualization
    - Add ACS quirks for Intel 9-series PCH root ports (Alex Williamson)
    - Add function 1 DMA alias quirk for Marvell 9120 (Sakari Ailus)

  MSI
    - Disable MSI at enumeration even if kernel doesn't support MSI (Michael S. Tsirkin)
    - Remove unused pci_msi_off() (Bjorn Helgaas)
    - Rename msi_set_enable(), msix_clear_and_set_ctrl() (Michael S.  Tsirkin)
    - Export pci_msi_set_enable(), pci_msix_clear_and_set_ctrl() (Michael S. Tsirkin)
    - Drop pci_msi_off() calls during probe (Michael S. Tsirkin)

  APM X-Gene host bridge driver
    - Add APM X-Gene v1 PCIe MSI/MSIX termination driver (Duc Dang)
    - Add APM X-Gene PCIe MSI DTS nodes (Duc Dang)
    - Disable Configuration Request Retry Status for v1 silicon (Duc Dang)
    - Allow config access to Root Port even when link is down (Duc Dang)

  Broadcom iProc host bridge driver
    - Allow override of device tree IRQ mapping function (Hauke Mehrtens)
    - Add BCMA PCIe driver (Hauke Mehrtens)
    - Directly add PCI resources (Hauke Mehrtens)
    - Free resource list after registration (Hauke Mehrtens)

  Freescale i.MX6 host bridge driver
    - Add speed change timeout message (Troy Kisky)
    - Rename imx6_pcie_start_link() to imx6_pcie_establish_link() (Bjorn Helgaas)

  Freescale Layerscape host bridge driver
    - Use dw_pcie_link_up() consistently (Bjorn Helgaas)
    - Factor out ls_pcie_establish_link() (Bjorn Helgaas)

  Marvell MVEBU host bridge driver
    - Remove mvebu_pcie_scan_bus() (Yijing Wang)

  NVIDIA Tegra host bridge driver
    - Remove tegra_pcie_scan_bus() (Yijing Wang)

  Synopsys DesignWare host bridge driver
    - Consolidate outbound iATU programming functions (Jisheng Zhang)
    - Use iATU0 for cfg and IO, iATU1 for MEM (Jisheng Zhang)
    - Add support for x8 links (Zhou Wang)
    - Wait for link to come up with consistent style (Bjorn Helgaas)
    - Use pci_scan_root_bus() for simplicity (Yijing Wang)

  TI DRA7xx host bridge driver
    - Use dw_pcie_link_up() consistently (Bjorn Helgaas)

  Miscellaneous
    - Include <linux/pci.h>, not <asm/pci.h> (Bjorn Helgaas)
    - Remove unnecessary #includes of <asm/pci.h> (Bjorn Helgaas)
    - Remove unused pcibios_select_root() (again) (Bjorn Helgaas)
    - Remove unused pci_dma_burst_advice() (Bjorn Helgaas)
    - xen/pcifront: Don't use deprecated function pci_scan_bus_parented() (Arnd Bergmann)"

* tag 'pci-v4.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (58 commits)
  PCI: pciehp: Inline the "handle event" functions into the ISR
  PCI: pciehp: Rename queue_interrupt_event() to pciehp_queue_interrupt_event()
  PCI: pciehp: Make queue_interrupt_event() void
  PCI: xgene: Allow config access to Root Port even when link is down
  PCI: xgene: Disable Configuration Request Retry Status for v1 silicon
  PCI: pciehp: Clean up debug logging
  x86/PCI: Use host bridge _CRS info on systems with >32 bit addressing
  PCI: imx6: Add #define PCIE_RC_LCSR
  PCI: imx6: Use "u32", not "uint32_t"
  PCI: Remove unused pci_scan_bus_parented()
  xen/pcifront: Don't use deprecated function pci_scan_bus_parented()
  PCI: imx6: Add speed change timeout message
  PCI/ASPM: Simplify Clock Power Management setting
  PCI: designware: Wait for link to come up with consistent style
  PCI: layerscape: Factor out ls_pcie_establish_link()
  PCI: layerscape: Use dw_pcie_link_up() consistently
  PCI: dra7xx: Use dw_pcie_link_up() consistently
  x86/PCI: Use host bridge _CRS info on Foxconn K8M890-8237A
  PCI: pciehp: Wait for hotplug command completion where necessary
  PCI: Remove unused pci_dma_burst_advice()
  ...

Merge tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:

 - new driver for Microchip TC74

 - support for ncpXXwf104 added to ntc_thermistor driver

 - minor cleanup

* tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: add driver for Microchip TC74
  hwmon: (ntc_thermistor) Improve precision of resistance calculation
  hwmon: (ntc_thermistor) fix iio raw to microvolts conversion
  hwmon: (atxp1) Drop auto-detection
  hwmon: (atxp1) Drop FSF mailing address
  hwmon: Allow compile test of GPIO consumers if !GPIOLIB
  hwmon: (sht15) Constify platform_device_id
  hwmon: (max197) Constify platform_device_id
  hwmon: (ntc_thermistor) Add support for ncpXXwf104

Pull MMC updates from Ulf Hansson:
 "Here are the changes for MMC for v4.2.

  MMC core:
   - Fix an error path in the mmc block layer
   - Fix PM domain attachment for the SDIO bus
   - Add support for driver strength selection
   - Increase a delay to let voltage stabilize
   - Add support for disabling write-protect detection
   - Add facility to support re-tuning
   - Re-tune and retry in the recovery path
   - Add reset option for SDIO
   - Consolidations and clean-ups

  MMC host:
   - Add Mediatek MMC driver
   - Constify platform_device_id for a couple of hosts
   - Fix modalias to make module auto-loading work for a couple of hosts
   - sdhci: Add support for sdhci-arasan4.9a
   - sdhci: Fix low memory corruption
   - sdhci: Restore behavior while creating OCR mask
   - sdhci: Add a callback to select drive strength
   - sdhci: Fix driver type B and D handling
   - sdhci: Add support for drive strength selection for SPT
   - sdhci: Enable HS400 for some Intel host controllers
   - sdhci: Convert to use the new re-tuning facility
   - sdhci: Various minor fixes and clean-ups
   - dw_mmc: Add support for hi6220
   - dw_mmc: Use core to handle absent write protect line
   - dw_mmc: Add support to switch voltage
   - tmio: Some fixes and modernizations
   - sh_mmcif: Improve clock rate calculation"

* tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc: (98 commits)
  mmc: queue: prevent soft lockups on PREEMPT=n
  mmc: mediatek: Add PM support for MMC driver
  mmc: mediatek: Add Mediatek MMC driver
  mmc: dt-bindings: add Mediatek MMC bindings
  mmc: card: Fixup request missing in mmc_blk_issue_rw_rq
  mmc: sdhci: fix low memory corruption
  mmc: sdhci-pci: Change AMD SDHCI quirk application scope
  i2c-piix4: Use Macro for AMD CZ SMBus device ID
  pci_ids: Add AMD KERNCZ device ID support
  mmc: queue: use swap() in mmc_queue_thread()
  mmc: dw_mmc: insmod followed by rmmod will hung for eMMC
  mmc: sdhci: Restore behavior while creating OCR mask
  mmc: sdhci-pxav3: fix device wakeup initialization
  mmc: core: Attach PM domain prior probing of SDIO func driver
  mmc: core: Remove redundant ->power_restore() callback for SD
  mmc: core: Remove redundant ->power_restore() callback for MMC
  mmc: sdhci-bcm2835: Actually enable the clock
  mmc: sdhci-bcm2835: Clean up platform allocations if sdhci init fails.
  mmc: sdhci-of-esdhc: enable interrupt mode to detect card
  mmc: sdhci-esdhc-imx: add quirk SDHCI_QUIRK2_BROKEN_HS200 for imx6qdl
  ...

Pull gpio updates from Linus Walleij:
 "This is the big bulk of GPIO changes queued for the v4.2 kernel
  series:

   - a big set of cleanups to the aged sysfs interface from Johan
     Hovold.  To get these in, v4.1-rc3 was merged into the tree as the
     first patch in that series had to go into stable.  This makes the
     locking much more fine-grained (get rid of the "big GPIO lock(s)"
     and store states in the GPIO descriptors.

   - rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
     avoid confusions.

   - New drivers for:
      * NXP LPC18xx (currently LPC1850)
      * NetLogic XLP
      * Broadcom STB SoC's
      * Axis ETRAXFS
      * Zynq Ultrascale+ (subdriver)

   - ACPI:
      * make it possible to retrieve GpioInt resources from a GPIO
        device using acpi_dev_gpio_irq_get()
      * merge some dependent I2C changes exploiting this.
      * support the ARM X-Gene GPIO standby driver.

   - make it possible for the generic GPIO driver to read back the value
     set registers to reflect current status.

   - loads of OMAP IRQ handling fixes.

   - incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
     PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.

   - janitorial (constification, checkpatch cleanups)"

* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
  gpio: Fix checkpatch.pl issues
  gpio: pcf857x: handle only enabled irqs
  gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
  GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
  gpio: improve error reporting on own descriptors
  gpio: promote own request failure to pr_err()
  gpio: Added support to Zynq Ultrascale+ MPSoC
  gpio: add ETRAXFS GPIO driver
  fix documentation after renaming gpiod_set_array to gpiod_set_array_value
  gpio: Add GPIO support for Broadcom STB SoCs
  gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
  gpio: tb10x: Drop unneeded free_irq() call
  gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
  gpio: stp-xway: Use the of_property_read_u32 helper
  gpio: pcf857x: Check for irq_set_irq_wake() failures
  gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
  gpio: Prevent an integer overflow in the pca953x driver
  gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
  gpio: omap: rework omap_gpio_request to touch only gpio specific registers
  gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
  ...

Merge tag 'pwm/for-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm updates from Thierry Reding:
 "This has a couple of fixes for Atmel, Samsung and Broadcom drivers.

  Some preparatory patches for more upcoming Intel work is included as
  well"

* tag 'pwm/for-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: lpss: pci: Add support for Broxton platform
  pwm: bcm-kona: Don't set polarity in probe
  pwm: Add pwmchip_add_with_polarity() API
  pwm: atmel: Fix incorrect CDTY value after disabling
  pwm: atmel: Fix incorrect CDTY value after enabling
  pwm: samsung: Use MODULE_DEVICE_TABLE() to include OF modalias
  pwm: Add support to remove registered consumer lookup tables

Pull crypto update from Herbert Xu:
 "Here is the crypto update for 4.2:

  API:

   - Convert RNG interface to new style.

   - New AEAD interface with one SG list for AD and plain/cipher text.
     All external AEAD users have been converted.

   - New asymmetric key interface (akcipher).

  Algorithms:

   - Chacha20, Poly1305 and RFC7539 support.

   - New RSA implementation.

   - Jitter RNG.

   - DRBG is now seeded with both /dev/random and Jitter RNG.  If kernel
     pool isn't ready then DRBG will be reseeded when it is.

   - DRBG is now the default crypto API RNG, replacing krng.

   - 842 compression (previously part of powerpc nx driver).

  Drivers:

   - Accelerated SHA-512 for arm64.

   - New Marvell CESA driver that supports DMA and more algorithms.

   - Updated powerpc nx 842 support.

   - Added support for SEC1 hardware to talitos"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
  crypto: marvell/cesa - remove COMPILE_TEST dependency
  crypto: algif_aead - Temporarily disable all AEAD algorithms
  crypto: af_alg - Forbid the use internal algorithms
  crypto: echainiv - Only hold RNG during initialisation
  crypto: seqiv - Add compatibility support without RNG
  crypto: eseqiv - Offer normal cipher functionality without RNG
  crypto: chainiv - Offer normal cipher functionality without RNG
  crypto: user - Add CRYPTO_MSG_DELRNG
  crypto: user - Move cryptouser.h to uapi
  crypto: rng - Do not free default RNG when it becomes unused
  crypto: skcipher - Allow givencrypt to be NULL
  crypto: sahara - propagate the error on clk_disable_unprepare() failure
  crypto: rsa - fix invalid select for AKCIPHER
  crypto: picoxcell - Update to the current clk API
  crypto: nx - Check for bogus firmware properties
  crypto: marvell/cesa - add DT bindings documentation
  crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
  crypto: marvell/cesa - add support for Orion SoCs
  crypto: marvell/cesa - add allhwsupport module parameter
  crypto: marvell/cesa - add support for all armada SoCs
  ...

Pull ia64 paravirt removal from Tony Luck:
 "Nobody cares about paravirtualization on ia64 anymore"

* tag 'please-pull-paravirt' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  ia64: remove paravirt code

Pull m68k update from Geert Uytterhoeven.

* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Use for_each_sg()
  m68k/defconfig: Update defconfigs for v4.1-rc6

Pull irq updates from Thomas Gleixner:
 "The irq departement delivers:

   - plug a potential race related to chained interrupt handlers

   - core updates which address the needs of the x86 irqdomain conversion

   - new irqchip callback to support affinity settings for VCPUs

   - the usual pile of updates to interrupt chip drivers

   - a few helper functions to allow further cleanups and
     simplifications

  I have a largish pile of coccinelle scripted/verified cleanups and
  simplifications pending on top of that, but I prefer to send that
  towards the end of the merge window when the arch/driver changes have
  hit your tree to avoid API change wreckage as far as possible"

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
  genirq: Remove bogus restriction in irq_move_mask_irq()
  irqchip: atmel-aic5: Add sama5d2 support
  irq: spear-shirq: Fix race in installing chained IRQ handler
  irq: irq-keystone: Fix race in installing chained IRQ handler
  gpio: gpio-tegra: Fix race in installing chained IRQ handler
  gpio: gpio-mxs: Fix race in installing chained IRQ handler
  gpio: gpio-mxc: Fix race in installing chained IRQ handler
  ARM: gemini: Fix race in installing GPIO chained IRQ handler
  GPU: ipu: Fix race in installing IPU chained IRQ handler
  ARM: sa1100: convert SA11x0 related code to use new chained handler helper
  irq: Add irq_set_chained_handler_and_data()
  irqchip: exynos-combiner: Save IRQ enable set on suspend
  genirq: Introduce helper function irq_data_get_affinity_mask()
  genirq: Introduce helper function irq_data_get_node()
  genirq: Introduce struct irq_common_data to host shared irq data
  genirq: Prevent crash in irq_move_irq()
  genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
  irqchip: gic: Simplify gic_configure_irq by using IRQCHIP_SET_TYPE_MASKED
  irqchip: renesas: intc-irqpin: Improve binding documentation
  genirq: Set IRQCHIP_SKIP_SET_WAKE for no_irq_chip
  ...

Pull NOHZ updates from Thomas Gleixner:
 "A few updates to the nohz infrastructure:

   - recursion protection for context tracking

   - make the TIF_NOHZ inheritance smarter

   - isolate cpus which belong to the NOHZ full set"

* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  nohz: Set isolcpus when nohz_full is set
  nohz: Add tick_nohz_full_add_cpus_to() API
  context_tracking: Inherit TIF_NOHZ through forks instead of context switches
  context_tracking: Protect against recursion

Pull timer updates from Thomas Gleixner:
 "A rather largish update for everything time and timer related:

   - Cache footprint optimizations for both hrtimers and timer wheel

   - Lower the NOHZ impact on systems which have NOHZ or timer migration
     disabled at runtime.

   - Optimize run time overhead of hrtimer interrupt by making the clock
     offset updates smarter

   - hrtimer cleanups and removal of restrictions to tackle some
     problems in sched/perf

   - Some more leap second tweaks

   - Another round of changes addressing the 2038 problem

   - First step to change the internals of clock event devices by
     introducing the necessary infrastructure

   - Allow constant folding for usecs/msecs_to_jiffies()

   - The usual pile of clockevent/clocksource driver updates

  The hrtimer changes contain updates to sched, perf and x86 as they
  depend on them plus changes all over the tree to cleanup API changes
  and redundant code, which got copied all over the place.  The y2038
  changes touch s390 to remove the last non 2038 safe code related to
  boot/persistant clock"

* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
  clocksource: Increase dependencies of timer-stm32 to limit build wreckage
  timer: Minimize nohz off overhead
  timer: Reduce timer migration overhead if disabled
  timer: Stats: Simplify the flags handling
  timer: Replace timer base by a cpu index
  timer: Use hlist for the timer wheel hash buckets
  timer: Remove FIFO "guarantee"
  timers: Sanitize catchup_timer_jiffies() usage
  hrtimer: Allow hrtimer::function() to free the timer
  seqcount: Introduce raw_write_seqcount_barrier()
  seqcount: Rename write_seqcount_barrier()
  hrtimer: Fix hrtimer_is_queued() hole
  hrtimer: Remove HRTIMER_STATE_MIGRATE
  selftest: Timers: Avoid signal deadlock in leap-a-day
  timekeeping: Copy the shadow-timekeeper over the real timekeeper last
  clockevents: Check state instead of mode in suspend/resume path
  selftests: timers: Add leap-second timer edge testing to leap-a-day.c
  ntp: Do leapsecond adjustment in adjtimex read path
  time: Prevent early expiry of hrtimers[CLOCK_REALTIME] at the leap second edge
  ntp: Introduce and use SECS_PER_DAY macro instead of 86400
  ...

Pull x86 core updates from Ingo Molnar:
 "There were so many changes in the x86/asm, x86/apic and x86/mm topics
  in this cycle that the topical separation of -tip broke down somewhat -
  so the result is a more traditional architecture pull request,
  collected into the 'x86/core' topic.

  The topics were still maintained separately as far as possible, so
  bisectability and conceptual separation should still be pretty good -
  but there were a handful of merge points to avoid excessive
  dependencies (and conflicts) that would have been poorly tested in the
  end.

  The next cycle will hopefully be much more quiet (or at least will
  have fewer dependencies).

  The main changes in this cycle were:

   * x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
     Gleixner)

     - This is the second and most intrusive part of changes to the x86
       interrupt handling - full conversion to hierarchical interrupt
       domains:

          [IOAPIC domain]   -----
                                 |
          [MSI domain]      --------[Remapping domain] ----- [ Vector domain ]
                                 |   (optional)          |
          [HPET MSI domain] -----                        |
                                                         |
          [DMAR domain]     -----------------------------
                                                         |
          [Legacy domain]   -----------------------------

       This now reflects the actual hardware and allowed us to distangle
       the domain specific code from the underlying parent domain, which
       can be optional in the case of interrupt remapping.  It's a clear
       separation of functionality and removes quite some duct tape
       constructs which plugged the remap code between ioapic/msi/hpet
       and the vector management.

     - Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
       injection into guests (Feng Wu)

   * x86/asm changes:

     - Tons of cleanups and small speedups, micro-optimizations.  This
       is in preparation to move a good chunk of the low level entry
       code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
       Brian Gerst)

     - Moved all system entry related code to a new home under
       arch/x86/entry/ (Ingo Molnar)

     - Removal of the fragile and ugly CFI dwarf debuginfo annotations.
       Conversion to C will reintroduce many of them - but meanwhile
       they are only getting in the way, and the upstream kernel does
       not rely on them (Ingo Molnar)

     - NOP handling refinements. (Borislav Petkov)

   * x86/mm changes:

     - Big PAT and MTRR rework: making the code more robust and
       preparing to phase out exposing direct MTRR interfaces to drivers -
       in favor of using PAT driven interfaces (Toshi Kani, Luis R
       Rodriguez, Borislav Petkov)

     - New ioremap_wt()/set_memory_wt() interfaces to support
       Write-Through cached memory mappings.  This is especially
       important for good performance on NVDIMM hardware (Toshi Kani)

   * x86/ras changes:

     - Add support for deferred errors on AMD (Aravind Gopalakrishnan)

       This is an important RAS feature which adds hardware support for
       poisoned data.  That means roughly that the hardware marks data
       which it has detected as corrupted but wasn't able to correct, as
       poisoned data and raises an APIC interrupt to signal that in the
       form of a deferred error.  It is the OS's responsibility then to
       take proper recovery action and thus prolonge system lifetime as
       far as possible.

     - Add support for Intel "Local MCE"s: upcoming CPUs will support
       CPU-local MCE interrupts, as opposed to the traditional system-
       wide broadcasted MCE interrupts (Ashok Raj)

     - Misc cleanups (Borislav Petkov)

   * x86/platform changes:

     - Intel Atom SoC updates

  ... and lots of other cleanups, fixlets and other changes - see the
  shortlog and the Git log for details"

* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
  x86/hpet: Use proper hpet device number for MSI allocation
  x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
  x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
  x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
  x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
  genirq: Prevent crash in irq_move_irq()
  genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
  iommu, x86: Properly handle posted interrupts for IOMMU hotplug
  iommu, x86: Provide irq_remapping_cap() interface
  iommu, x86: Setup Posted-Interrupts capability for Intel iommu
  iommu, x86: Add cap_pi_support() to detect VT-d PI capability
  iommu, x86: Avoid migrating VT-d posted interrupts
  iommu, x86: Save the mode (posted or remapped) of an IRTE
  iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
  iommu: dmar: Provide helper to copy shared irte fields
  iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
  iommu: Add new member capability to struct irq_remap_ops
  x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
  x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
  x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
  ...

Pull x86 warning fixlet from Ingo Molnar:
 "A build fix for certain (rare) variants of binutils that did not make
  it into v4.1"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/boot: Fix overflow warning with 32-bit binutils

Pul x86 microcode updates from Ingo Molnar:
 "x86 microcode loader updates from Borislav Petkov:

   - early parsing of the built-in microcode

   - cleanups

   - misc smaller fixes"

* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode: Correct CPU family related variable types
  x86/microcode: Disable builtin microcode loading on 32-bit for now
  x86/microcode/intel: Rename get_matching_sig()
  x86/microcode/intel: Simplify get_matching_sig()
  x86/microcode/intel: Simplify update_match_cpu()
  x86/microcode/intel: Rename get_matching_microcode
  x86/cpu/microcode: Zap changelog
  x86/microcode: Parse built-in microcode early
  x86/microcode/intel: Remove unused @rev arg of get_matching_sig()
  x86/microcode/intel: Get rid of revision_is_newer()

Pull x86 kdump updates from Ingo Molnar:
 "Three kdump robustness related improvements (Joerg Roedel)"

* 'x86-kdump-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/crash: Allocate enough low memory when crashkernel=high
  x86/swiotlb: Try coherent allocations with __GFP_NOWARN
  swiotlb: Warn on allocation failure in swiotlb_alloc_coherent()

Pull x86 FPU updates from Ingo Molnar:
 "This tree contains two main changes:

   - The big FPU code rewrite: wide reaching cleanups and reorganization
     that pulls all the FPU code together into a clean base in
     arch/x86/fpu/.

     The resulting code is leaner and faster, and much easier to
     understand.  This enables future work to further simplify the FPU
     code (such as removing lazy FPU restores).

     By its nature these changes have a substantial regression risk: FPU
     code related bugs are long lived, because races are often subtle
     and bugs mask as user-space failures that are difficult to track
     back to kernel side backs.  I'm aware of no unfixed (or even
     suspected) FPU related regression so far.

   - MPX support rework/fixes.  As this is still not a released CPU
     feature, there were some buglets in the code - should be much more
     robust now (Dave Hansen)"

* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (250 commits)
  x86/fpu: Fix double-increment in setup_xstate_features()
  x86/mpx: Allow 32-bit binaries on 64-bit kernels again
  x86/mpx: Do not count MPX VMAs as neighbors when unmapping
  x86/mpx: Rewrite the unmap code
  x86/mpx: Support 32-bit binaries on 64-bit kernels
  x86/mpx: Use 32-bit-only cmpxchg() for 32-bit apps
  x86/mpx: Introduce new 'directory entry' to 'addr' helper function
  x86/mpx: Add temporary variable to reduce masking
  x86: Make is_64bit_mm() widely available
  x86/mpx: Trace allocation of new bounds tables
  x86/mpx: Trace the attempts to find bounds tables
  x86/mpx: Trace entry to bounds exception paths
  x86/mpx: Trace #BR exceptions
  x86/mpx: Introduce a boot-time disable flag
  x86/mpx: Restrict the mmap() size check to bounds tables
  x86/mpx: Remove redundant MPX_BNDCFG_ADDR_MASK
  x86/mpx: Clean up the code by not passing a task pointer around when unnecessary
  x86/mpx: Use the new get_xsave_field_ptr()API
  x86/fpu/xstate: Wrap get_xsave_addr() to make it safer
  x86/fpu/xstate: Fix up bad get_xsave_addr() assumptions
  ...

Pull x86 EFI updates from Ingo Molnar:
 "EFI changes:

   - Use idiomatic negative error values in efivar_create_sysfs_entry()
     instead of returning '1' to indicate error (Dan Carpenter)

   - Implement new support to expose the EFI System Resource Tables in
     sysfs, which provides information for performing firmware updates
     (Peter Jones)

   - Documentation cleanup in the EFI handover protocol section which
     falsely claimed that 'cmdline_size' needed to be filled out by the
     boot loader (Alex Smith)

   - Align the order of SMBIOS tables in /sys/firmware/efi/systab to
     match the way that we do things for ACPI and add documentation to
     Documentation/ABI (Jean Delvare)"

* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi: Work around ia64 build problem with ESRT driver
  efi: Add 'systab' information to Documentation/ABI
  efi: dmi: List SMBIOS3 table before SMBIOS table
  efi/esrt: Fix some compiler warnings
  x86, doc: Remove cmdline_size from list of fields to be filled in for EFI handover
  efi: Add esrt support
  efi: efivar_create_sysfs_entry() should return negative error codes

Pull x86 debugging documentation updates from Ingo Molnar:
 "Documentation updates about x86 kernel stacks"

* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/Documentation: Adapt Ingo's explanation on printing backtraces
  x86/Documentation: Remove STACKFAULT_STACK bulletpoint
  x86/Documentation: Move kernel-stacks doc one level up

Pull x86 CPU features from Ingo Molnar:
 "Various CPU feature support related changes: in particular the
  /proc/cpuinfo model name sanitization change should be monitored, it
  has a chance to break stuff.  (but really shouldn't and there are no
  regression reports)"

* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu/amd: Give access to the number of nodes in a physical package
  x86/cpu: Trim model ID whitespace
  x86/cpu: Strip any /proc/cpuinfo model name field whitespace
  x86/cpu/amd: Set X86_FEATURE_EXTD_APICID for future processors
  x86/gart: Check for GART support before accessing GART registers

Pull x86 cleanups from Ingo Molnar:
 "Misc cleanups"

* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Clean up types in xlate_dev_mem_ptr() some more
  x86: Deinline dma_free_attrs()
  x86: Deinline dma_alloc_attrs()
  x86: Remove unused TI_cpu
  x86: Merge common 32-bit values in asm-offsets.c

Pull scheduler updates from Ingo Molnar:
 "The main changes are:

   - lockless wakeup support for futexes and IPC message queues
     (Davidlohr Bueso, Peter Zijlstra)

   - Replace spinlocks with atomics in thread_group_cputimer(), to
     improve scalability (Jason Low)

   - NUMA balancing improvements (Rik van Riel)

   - SCHED_DEADLINE improvements (Wanpeng Li)

   - clean up and reorganize preemption helpers (Frederic Weisbecker)

   - decouple page fault disabling machinery from the preemption
     counter, to improve debuggability and robustness (David
     Hildenbrand)

   - SCHED_DEADLINE documentation updates (Luca Abeni)

   - topology CPU masks cleanups (Bartosz Golaszewski)

   - /proc/sched_debug improvements (Srikar Dronamraju)"

* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
  sched/deadline: Remove needless parameter in dl_runtime_exceeded()
  sched: Remove superfluous resetting of the p->dl_throttled flag
  sched/deadline: Drop duplicate init_sched_dl_class() declaration
  sched/deadline: Reduce rq lock contention by eliminating locking of non-feasible target
  sched/deadline: Make init_sched_dl_class() __init
  sched/deadline: Optimize pull_dl_task()
  sched/preempt: Add static_key() to preempt_notifiers
  sched/preempt: Fix preempt notifiers documentation about hlist_del() within unsafe iteration
  sched/stop_machine: Fix deadlock between multiple stop_two_cpus()
  sched/debug: Add sum_sleep_runtime to /proc/<pid>/sched
  sched/debug: Replace vruntime with wait_sum in /proc/sched_debug
  sched/debug: Properly format runnable tasks in /proc/sched_debug
  sched/numa: Only consider less busy nodes as numa balancing destinations
  Revert 095bebf6 ("sched/numa: Do not move past the balance point if unbalanced")
  sched/fair: Prevent throttling in early pick_next_task_fair()
  preempt: Reorganize the notrace definitions a bit
  preempt: Use preempt_schedule_context() as the official tracing preemption point
  sched: Make preempt_schedule_context() function-tracing safe
  x86: Remove cpu_sibling_mask() and cpu_core_mask()
  x86: Replace cpu_**_mask() with topology_**_cpumask()
  ...

Pull perf fixes from Ingo Molnar:
 "These are the left over fixes from the v4.1 cycle"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf tools: Fix build breakage if prefix= is specified
  perf/x86: Honor the architectural performance monitoring version
  perf/x86/intel: Fix PMI handling for Intel PT
  perf/x86/intel/bts: Fix DS area sharing with x86_pmu events
  perf/x86: Add more Broadwell model numbers
  perf: Fix ring_buffer_attach() RCU sync, again

Pull perf updates from Ingo Molnar:
 "Kernel side changes mostly consist of work on x86 PMU drivers:

   - x86 Intel PT (hardware CPU tracer) improvements (Alexander
     Shishkin)

   - x86 Intel CQM (cache quality monitoring) improvements (Thomas
     Gleixner)

   - x86 Intel PEBSv3 support (Peter Zijlstra)

   - x86 Intel PEBS interrupt batching support for lower overhead
     sampling (Zheng Yan, Kan Liang)

   - x86 PMU scheduler fixes and improvements (Peter Zijlstra)

  There's too many tooling improvements to list them all - here are a
  few select highlights:

  'perf bench':

      - Introduce new 'perf bench futex' benchmark: 'wake-parallel', to
        measure parallel waker threads generating contention for kernel
        locks (hb->lock). (Davidlohr Bueso)

  'perf top', 'perf report':

      - Allow disabling/enabling events dynamicaly in 'perf top':
        a 'perf top' session can instantly become a 'perf report'
        one, i.e. going from dynamic analysis to a static one,
        returning to a dynamic one is possible, to toogle the
        modes, just press 'f' to 'freeze/unfreeze' the sampling. (Arnaldo Carvalho de Melo)

      - Make Ctrl-C stop processing on TUI, allowing interrupting the load of big
        perf.data files (Namhyung Kim)

  'perf probe': (Masami Hiramatsu)

      - Support glob wildcards for function name
      - Support $params special probe argument: Collect all function arguments
      - Make --line checks validate C-style function name.
      - Add --no-inlines option to avoid searching inline functions
      - Greatly speed up 'perf probe --list' by caching debuginfo.
      - Improve --filter support for 'perf probe', allowing using its arguments
        on other commands, as --add, --del, etc.

  'perf sched':

      - Add option in 'perf sched' to merge like comms to lat output (Josef Bacik)

  Plus tons of infrastructure work - in particular preparation for
  upcoming threaded perf report support, but also lots of other work -
  and fixes and other improvements.  See (much) more details in the
  shortlog and in the git log"

* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (305 commits)
  perf tools: Configurable per thread proc map processing time out
  perf tools: Add time out to force stop proc map processing
  perf report: Fix sort__sym_cmp to also compare end of symbol
  perf hists browser: React to unassigned hotkey pressing
  perf top: Tell the user how to unfreeze events after pressing 'f'
  perf hists browser: Honour the help line provided by builtin-{top,report}.c
  perf hists browser: Do not exit when 'f' is pressed in 'report' mode
  perf top: Replace CTRL+z with 'f' as hotkey for enable/disable events
  perf annotate: Rename source_line_percent to source_line_samples
  perf annotate: Display total number of samples with --show-total-period
  perf tools: Ensure thread-stack is flushed
  perf top: Allow disabling/enabling events dynamicly
  perf evlist: Add toggle_enable() method
  perf trace: Fix race condition at the end of started workloads
  perf probe: Speed up perf probe --list by caching debuginfo
  perf probe: Show usage even if the last event is skipped
  perf tools: Move libtraceevent dynamic list to separated LDFLAGS variable
  perf tools: Fix a problem when opening old perf.data with different byte order
  perf tools: Ignore .config-detected in .gitignore
  perf probe: Fix to return error if no probe is added
  ...

Pull locking updates from Ingo Molnar:
 "The main changes are:

   - 'qspinlock' support, enabled on x86: queued spinlocks - these are
     now the spinlock variant used by x86 as they outperform ticket
     spinlocks in every category.  (Waiman Long)

   - 'pvqspinlock' support on x86: paravirtualized variant of queued
     spinlocks.  (Waiman Long, Peter Zijlstra)

   - 'qrwlock' support, enabled on x86: queued rwlocks.  Similar to
     queued spinlocks, they are now the variant used by x86:

       CONFIG_ARCH_USE_QUEUED_SPINLOCKS=y
       CONFIG_QUEUED_SPINLOCKS=y
       CONFIG_ARCH_USE_QUEUED_RWLOCKS=y
       CONFIG_QUEUED_RWLOCKS=y

   - various lockdep fixlets

   - various locking primitives cleanups, further WRITE_ONCE()
     propagation"

* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
  locking/lockdep: Remove hard coded array size dependency
  locking/qrwlock: Don't contend with readers when setting _QW_WAITING
  lockdep: Do not break user-visible string
  locking/arch: Rename set_mb() to smp_store_mb()
  locking/arch: Add WRITE_ONCE() to set_mb()
  rtmutex: Warn if trylock is called from hard/softirq context
  arch: Remove __ARCH_HAVE_CMPXCHG
  locking/rtmutex: Drop usage of __HAVE_ARCH_CMPXCHG
  locking/qrwlock: Rename QUEUE_RWLOCK to QUEUED_RWLOCKS
  locking/pvqspinlock: Rename QUEUED_SPINLOCK to QUEUED_SPINLOCKS
  locking/pvqspinlock: Replace xchg() by the more descriptive set_mb()
  locking/pvqspinlock, x86: Enable PV qspinlock for Xen
  locking/pvqspinlock, x86: Enable PV qspinlock for KVM
  locking/pvqspinlock, x86: Implement the paravirt qspinlock call patching
  locking/pvqspinlock: Implement simple paravirt support for the qspinlock
  locking/qspinlock: Revert to test-and-set on hypervisors
  locking/qspinlock: Use a simple write to grab the lock
  locking/qspinlock: Optimize for smaller NR_CPUS
  locking/qspinlock: Extract out code snippets for the next patch
  locking/qspinlock: Add pending bit
  ...

Pull RCU updates from Ingo Molnar:

 - Continued initialization/Kconfig updates: hide most Kconfig options
   from unsuspecting users.

   There's now a single high level configuration option:

        *
        * RCU Subsystem
        *
        Make expert-level adjustments to RCU configuration (RCU_EXPERT) [N/y/?] (NEW)

   Which if answered in the negative, leaves us with a single
   interactive configuration option:

        Offload RCU callback processing from boot-selected CPUs (RCU_NOCB_CPU) [N/y/?] (NEW)

   All the rest of the RCU options are configured automatically.  Later
   on we'll remove this single leftover configuration option as well.

 - Remove all uses of RCU-protected array indexes: replace the
   rcu_[access|dereference]_index_check() APIs with READ_ONCE() and
   rcu_lockdep_assert()

 - RCU CPU-hotplug cleanups

 - Updates to Tiny RCU: a race fix and further code shrinkage.

 - RCU torture-testing updates: fixes, speedups, cleanups and
   documentation updates.

 - Miscellaneous fixes

 - Documentation updates

* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
  rcutorture: Allow repetition factors in Kconfig-fragment lists
  rcutorture: Display "make oldconfig" errors
  rcutorture: Update TREE_RCU-kconfig.txt
  rcutorture: Make rcutorture scripts force RCU_EXPERT
  rcutorture: Update configuration fragments for rcutree.rcu_fanout_exact
  rcutorture: TASKS_RCU set directly, so don't explicitly set it
  rcutorture: Test SRCU cleanup code path
  rcutorture: Replace barriers with smp_store_release() and smp_load_acquire()
  locktorture: Change longdelay_us to longdelay_ms
  rcutorture: Allow negative values of nreaders to oversubscribe
  rcutorture: Exchange TREE03 and TREE08 NR_CPUS, speed up CPU hotplug
  rcutorture: Exchange TREE03 and TREE04 geometries
  locktorture: fix deadlock in 'rw_lock_irq' type
  rcu: Correctly handle non-empty Tiny RCU callback list with none ready
  rcutorture: Test both RCU-sched and RCU-bh for Tiny RCU
  rcu: Further shrink Tiny RCU by making empty functions static inlines
  rcu: Conditionally compile RCU's eqs warnings
  rcu: Remove prompt for RCU implementation
  rcu: Make RCU able to tolerate undefined CONFIG_RCU_KTHREAD_PRIO
  rcu: Make RCU able to tolerate undefined CONFIG_RCU_FANOUT_LEAF
  ...

Pull vfs updates from Al Viro:
 "In this pile: pathname resolution rewrite.

   - recursion in link_path_walk() is gone.

   - nesting limits on symlinks are gone (the only limit remaining is
     that the total amount of symlinks is no more than 40, no matter how
     nested).

   - "fast" (inline) symlinks are handled without leaving rcuwalk mode.

   - stack footprint (independent of the nesting) is below kilobyte now,
     about on par with what it used to be with one level of nested
     symlinks and ~2.8 times lower than it used to be in the worst case.

   - struct nameidata is entirely private to fs/namei.c now (not even
     opaque pointers are being passed around).

   - ->follow_link() and ->put_link() calling conventions had been
     changed; all in-tree filesystems converted, out-of-tree should be
     able to follow reasonably easily.

     For out-of-tree conversions, see Documentation/filesystems/porting
     for details (and in-tree filesystems for examples of conversion).

  That has sat in -next since mid-May, seems to survive all testing
  without regressions and merges clean with v4.1"

* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (131 commits)
  turn user_{path_at,path,lpath,path_dir}() into static inlines
  namei: move saved_nd pointer into struct nameidata
  inline user_path_create()
  inline user_path_parent()
  namei: trim do_last() arguments
  namei: stash dfd and name into nameidata
  namei: fold path_cleanup() into terminate_walk()
  namei: saner calling conventions for filename_parentat()
  namei: saner calling conventions for filename_create()
  namei: shift nameidata down into filename_parentat()
  namei: make filename_lookup() reject ERR_PTR() passed as name
  namei: shift nameidata inside filename_lookup()
  namei: move putname() call into filename_lookup()
  namei: pass the struct path to store the result down into path_lookupat()
  namei: uninline set_root{,_rcu}()
  namei: be careful with mountpoint crossings in follow_dotdot_rcu()
  Documentation: remove outdated information from automount-support.txt
  get rid of assorted nameidata-related debris
  lustre: kill unused helper
  lustre: kill unused macro (LOOKUP_CONTINUE)
  ...

The CESA driver calls phys_to_virt() which is not available on all
architectures.
Remove the depency on COMPILE_TEST to prevent building this driver on
non ARM architectures.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

As the AEAD conversion is still ongoing, we do not yet wish to
export legacy AEAD implementations to user-space, as their calling
convention will change.

This patch actually disables all AEAD algorithms because some of
them (e.g., cryptd) will need to be modified to propagate this flag.

Subsequent patches will reenable them on an individual basis.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The bit CRYPTO_ALG_INTERNAL was added to stop af_alg from accessing
internal algorithms.  However, af_alg itself was never modified to
actually stop that bit from being used by the user.  Therefore the
user could always override it by specifying the relevant bit in the
type and/or mask.

This patch silently discards the bit in both type and mask.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

This patch changes the RNG allocation so that we only hold a
reference to the RNG during initialisation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

When seqiv is used in compatibility mode, this patch allows it
to function even when an RNG Is not available.  It also changes
the RNG allocation for the new explicit seqiv interface so that
we only hold a reference to the RNG during initialisation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The RNG may not be available during early boot, e.g., the relevant
modules may not be included in the initramfs.  As the RNG Is only
needed for IPsec, we should not let this prevent use of ciphers
without IV generators, e.g., for disk encryption.

This patch postpones the RNG allocation to the init function so
that one failure during early boot does not make the RNG unavailable
for all subsequent users of the same cipher.

More importantly, it lets the cipher live even if RNG allocation
fails.  Of course we no longer offer IV generation and which will
fail with an error if invoked.  But all other cipher capabilities
will function as usual.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

The RNG may not be available during early boot, e.g., the relevant
modules may not be included in the initramfs.  As the RNG Is only
needed for IPsec, we should not let this prevent use of ciphers
without IV generators, e.g., for disk encryption.

This patch postpones the RNG allocation to the init function so
that one failure during early boot does not make the RNG unavailable
for all subsequent users of the same cipher.

More importantly, it lets the cipher live even if RNG allocation
fails.  Of course we no longer offer IV generation and which will
fail with an error if invoked.  But all other cipher capabilities
will function as usual.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>