- 22 Jan, 2019 14 commits
-
-
Loic Poulain authored
commit a89e7bcb upstream. The Clock Data Recovery (CDR) circuit allows to automatically adjust the RX sampling-point/phase for high frequency cards (SDR104, HS200...). CDR is automatically enabled during DLL configuration. However, according to the APQ8016 reference manual, this function must be disabled during TX and tuning phase in order to prevent any interferences during tuning challenges and unexpected phase alteration during TX transfers. This patch enables/disables CDR according to the current transfer mode. This fixes sporadic write transfer issues observed with some SDR104 and HS200 cards. Inspired by sdhci-msm downstream patch: https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/432516/Reported-by:
Leonid Segal <leonid.s@variscite.com> Reported-by:
Manabu Igusa <migusa@arrowjapan.com> Signed-off-by:
Loic Poulain <loic.poulain@linaro.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Acked-by:
Georgi Djakov <georgi.djakov@linaro.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> [georgi: backport to v4.19+] Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Florian Westphal authored
commit a0072320 upstream. Size and 'next bit' were swapped, this bug could cause worker to reschedule itself even if system was idle. Fixes: 5c789e13 ("netfilter: nf_conncount: Add list lock and gc worker, and RCU for init tree search") Reviewed-by:
Shawn Bohrer <sbohrer@cloudflare.com> Signed-off-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Pablo Neira Ayuso authored
commit c80f10bc upstream. Instead of removing a empty list node that might be reintroduced soon thereafter, tentatively place the empty list node on the list passed to tree_nodes_free(), then re-check if the list is empty again before erasing it from the tree. [ Florian: rebase on top of pending nf_conncount fixes ] Fixes: 5c789e13 ("netfilter: nf_conncount: Add list lock and gc worker, and RCU for init tree search") Reviewed-by:
-
Pablo Neira Ayuso authored
commit 2f971a8f upstream. Two CPUs may race to remove a connection from the list, the existing conn->dead will result in a use-after-free. Use the per-list spinlock to protect list iterations. As all accesses to the list now happen while holding the per-list lock, we no longer need to delay free operations with rcu. Joint work with Florian. Fixes: 5c789e13 ("netfilter: nf_conncount: Add list lock and gc worker, and RCU for init tree search") Reviewed-by:
-
Florian Westphal authored
commit df4a9025 upstream. 'lookup' is always followed by 'add'. Merge both and make the list-walk part of nf_conncount_add(). This also avoids one unneeded unlock/re-lock pair. Extra care needs to be taken in count_tree, as we only hold rcu read lock, i.e. we can only insert to an existing tree node after acquiring its lock and making sure it has a nonzero count. As a zero count should be rare, just fall back to insert_tree() (which acquires tree lock). This issue and its solution were pointed out by Shawn Bohrer during patch review. Reviewed-by:
-
Florian Westphal authored
commit e8cfb372 upstream. Shawn Bohrer reported a following crash: |RIP: 0010:rb_erase+0xae/0x360 [..] Call Trace: nf_conncount_destroy+0x59/0xc0 [nf_conncount] cleanup_match+0x45/0x70 [ip_tables] ... Shawn tracked this down to bogus 'parent' pointer: Problem is that when we insert a new node, then there is a chance that the 'parent' that we found was also passed to tree_nodes_free() (because that node was empty) for erase+free. Instead of trying to be clever and detect when this happens, restart the search if we have evicted one or more nodes. To prevent frequent restarts, do not perform gc on the second round. Also, unconditionally schedule the gc worker. The condition gc_count > ARRAY_SIZE(gc_nodes)) cannot be true unless tree grows very large, as the height of the tree will be low even with hundreds of nodes present. Fixes: 5c789e13 ("netfilter: nf_conncount: Add list lock and gc worker, and RCU for init tree search") Reported-by:
-
Florian Westphal authored
commit f7fcc98d upstream. The lockless workqueue garbage collector can race with packet path garbage collector to delete list nodes, as it calls tree_nodes_free() with the addresses of nodes that might have been free'd already from another cpu. To fix this, split gc into two phases. One phase to perform gc on the connections: From a locking perspective, this is the same as count_tree(): we hold rcu lock, but we do not change the tree, we only change the nodes' contents. The second phase acquires the tree lock and reaps empty nodes. This avoids a race condition of the garbage collection vs. packet path: If a node has been free'd already, the second phase won't find it anymore. This second phase is, from locking perspective, same as insert_tree(). The former only modifies nodes (list content, count), latter modifies the tree itself (rb_erase or rb_insert). Fixes: 5c789e13 ("netfilter: nf_conncount: Add list lock and gc worker, and RCU for init tree search") Reviewed-by:
-
Florian Westphal authored
commit 4cd273bb upstream. age is signed integer, so result can be negative when the timestamps have a large delta. In this case we want to discard the entry. Instead of using age >= 2 || age < 0, just make it unsigned. Fixes: b36e4523 ("netfilter: nf_conncount: fix garbage collection confirm race") Reviewed-by:
-
Shawn Bohrer authored
commit c78e7818 upstream. Most of the time these were the same value anyway, but when CONFIG_LOCKDEP was enabled we would use a smaller number of locks to reduce overhead. Unfortunately having two values is confusing and not worth the complexity. This fixes a bug where tree_gc_worker() would only GC up to CONNCOUNT_LOCK_SLOTS trees which meant when CONFIG_LOCKDEP was enabled not all trees would be GCed by tree_gc_worker(). Fixes: 5c789e13 ("netfilter: nf_conncount: Add list lock and gc worker, and RCU for init tree search") Signed-off-by:
-
Oliver Hartkopp authored
commit 0aaa8137 upstream. Muyu Yu provided a POC where user root with CAP_NET_ADMIN can create a CAN frame modification rule that makes the data length code a higher value than the available CAN frame data size. In combination with a configured checksum calculation where the result is stored relatively to the end of the data (e.g. cgw_csum_xor_rel) the tail of the skb (e.g. frag_list pointer in skb_shared_info) can be rewritten which finally can cause a system crash. Michael Kubecek suggested to drop frames that have a DLC exceeding the available space after the modification process and provided a patch that can handle CAN FD frames too. Within this patch we also limit the length for the checksum calculations to the maximum of Classic CAN data length (8). CAN frames that are dropped by these additional checks are counted with the CGW_DELETED counter which indicates misconfigurations in can-gw rules. This fixes CVE-2019-3701. Reported-by:
Muyu Yu <ieatmuttonchuan@gmail.com> Reported-by:
Marcus Meissner <meissner@suse.de> Suggested-by:
Michal Kubecek <mkubecek@suse.cz> Tested-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Dmitry Safonov authored
commit d3736d82 upstream. Try to get reference for ldisc during tty_reopen(). If ldisc present, we don't need to do tty_ldisc_reinit() and lock the write side for line discipline semaphore. Effectively, it optimizes fast-path for tty_reopen(), but more importantly it won't interrupt ongoing IO on the tty as no ldisc change is needed. Fixes user-visible issue when tty_reopen() interrupted login process for user with a long password, observed and reported by Lukas. Fixes: c96cf923 ("tty: Don't block on IO when ldisc change is pending") Fixes: 83d817f4 ("tty: Hold tty_ldisc_lock() during tty_reopen()") Cc: Jiri Slaby <jslaby@suse.com> Reported-by:
Lukas F. Hartmann <lukas@mntmn.com> Tested-by:
Dmitry Safonov <dima@arista.com> Signed-off-by:
-
Dmitry Safonov authored
commit cf62a1a1 upstream. As notted by Jiri, tty_ldisc_reinit() shouldn't rely on tty counter. Simplify math by increasing the counter after reinit success. Cc: Jiri Slaby <jslaby@suse.com> Link: lkml.kernel.org/r/<20180829022353.23568-2-dima@arista.com> Suggested-by:
Jiri Slaby <jslaby@suse.com> Reviewed-by:
Jiri Slaby <jslaby@suse.cz> Tested-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
-
Dmitry Safonov authored
commit 83d817f4 upstream. tty_ldisc_reinit() doesn't race with neither tty_ldisc_hangup() nor set_ldisc() nor tty_ldisc_release() as they use tty lock. But it races with anyone who expects line discipline to be the same after hoding read semaphore in tty_ldisc_ref(). We've seen the following crash on v4.9.108 stable: BUG: unable to handle kernel paging request at 0000000000002260 IP: [..] n_tty_receive_buf_common+0x5f/0x86d Workqueue: events_unbound flush_to_ldisc Call Trace: [..] n_tty_receive_buf2 [..] tty_ldisc_receive_buf [..] flush_to_ldisc [..] process_one_work [..] worker_thread [..] kthread [..] ret_from_fork tty_ldisc_reinit() should be called with ldisc_sem hold for writing, which will protect any reader against line discipline changes. Cc: Jiri Slaby <jslaby@suse.com> Cc: stable@vger.kernel.org # b027e229 ("tty: fix data race between tty_init_dev and flush of buf") Reviewed-by:
Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Signed-off-by:
Tycho Andersen <tycho@tycho.ws> Signed-off-by:
-
Dmitry Safonov authored
commit 231f8fd0 upstream. ldsem_down_read() will sleep if there is pending writer in the queue. If the writer times out, readers in the queue should be woken up, otherwise they may miss a chance to acquire the semaphore until the last active reader will do ldsem_up_read(). There was a couple of reports where there was one active reader and other readers soft locked up: Showing all locks held in the system: 2 locks held by khungtaskd/17: #0: (rcu_read_lock){......}, at: watchdog+0x124/0x6d1 #1: (tasklist_lock){.+.+..}, at: debug_show_all_locks+0x72/0x2d3 2 locks held by askfirst/123: #0: (&tty->ldisc_sem){.+.+.+}, at: ldsem_down_read+0x46/0x58 #1: (&ldata->atomic_read_lock){+.+...}, at: n_tty_read+0x115/0xbe4 Prevent readers wait for active readers to release ldisc semaphore. Link: lkml.kernel.org/r/20171121132855.ajdv4k6swzhvktl6@wfg-t540p.sh.intel.com Link: lkml.kernel.org/r/20180907045041.GF1110@shao2-debian Cc: Jiri Slaby <jslaby@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Reported-by:
kernel test robot <rong.a.chen@intel.com> Signed-off-by:
-
- 16 Jan, 2019 26 commits
-
-
Greg Kroah-Hartman authored
-
Filipe Manana authored
commit 827aa18e upstream. When initializing the security xattrs, we are holding a transaction handle therefore we need to use a GFP_NOFS context in order to avoid a deadlock with reclaim in case it's triggered. Fixes: 39a27ec1 ("btrfs: use GFP_KERNEL for xattr and acl allocations") Reviewed-by:
Nikolay Borisov <nborisov@suse.com> Signed-off-by:
Filipe Manana <fdmanana@suse.com> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Filipe Manana authored
commit 9a6f209e upstream. If the quota enable and snapshot creation ioctls are called concurrently we can get into a deadlock where the task enabling quotas will deadlock on the fs_info->qgroup_ioctl_lock mutex because it attempts to lock it twice, or the task creating a snapshot tries to commit the transaction while the task enabling quota waits for the former task to commit the transaction while holding the mutex. The following time diagrams show how both cases happen. First scenario: CPU 0 CPU 1 btrfs_ioctl() btrfs_ioctl_quota_ctl() btrfs_quota_enable() mutex_lock(fs_info->qgroup_ioctl_lock) btrfs_start_transaction() btrfs_ioctl() btrfs_ioctl_snap_create_v2 create_snapshot() --> adds snapshot to the list pending_snapshots of the current transaction btrfs_commit_transaction() create_pending_snapshots() create_pending_snapshot() qgroup_account_snapshot() btrfs_qgroup_inherit() mutex_lock(fs_info->qgroup_ioctl_lock) --> deadlock, mutex already locked by this task at btrfs_quota_enable() Second scenario: CPU 0 CPU 1 btrfs_ioctl() btrfs_ioctl_quota_ctl() btrfs_quota_enable() mutex_lock(fs_info->qgroup_ioctl_lock) btrfs_start_transaction() btrfs_ioctl() btrfs_ioctl_snap_create_v2 create_snapshot() --> adds snapshot to the list pending_snapshots of the current transaction btrfs_commit_transaction() --> waits for task at CPU 0 to release its transaction handle btrfs_commit_transaction() --> sees another task started the transaction commit first --> releases its transaction handle --> waits for the transaction commit to be completed by the task at CPU 1 create_pending_snapshot() qgroup_account_snapshot() btrfs_qgroup_inherit() mutex_lock(fs_info->qgroup_ioctl_lock) --> deadlock, task at CPU 0 has the mutex locked but it is waiting for us to finish the transaction commit So fix this by setting the quota enabled flag in fs_info after committing the transaction at btrfs_quota_enable(). This ends up serializing quota enable and snapshot creation as if the snapshot creation happened just before the quota enable request. The quota rescan task, scheduled after committing the transaction in btrfs_quote_enable(), will do the accounting. Fixes: 6426c7ad ("btrfs: qgroup: Fix qgroup accounting when creating snapshot") Signed-off-by:
-
Filipe Manana authored
commit 5a8067c0 upstream. The available allocation bits members from struct btrfs_fs_info are protected by a sequence lock, and when starting balance we access them incorrectly in two different ways: 1) In the read sequence lock loop at btrfs_balance() we use the values we read from fs_info->avail_*_alloc_bits and we can immediately do actions that have side effects and can not be undone (printing a message and jumping to a label). This is wrong because a retry might be needed, so our actions must not have side effects and must be repeatable as long as read_seqretry() returns a non-zero value. In other words, we were essentially ignoring the sequence lock; 2) Right below the read sequence lock loop, we were reading the values from avail_metadata_alloc_bits and avail_data_alloc_bits without any protection from concurrent writers, that is, reading them outside of the read sequence lock critical section. So fix this by making sure we only read the available allocation bits while in a read sequence lock critical section and that what we do in the critical section is repeatable (has nothing that can not be undone) so that any eventual retry that is needed is handled properly. Fixes: de98ced9 ("Btrfs: use seqlock to protect fs_info->avail_{data, metadata, system}_alloc_bits") Fixes: 14506127 ("btrfs: fix a bogus warning when converting only data or metadata") Reviewed-by:
-
Will Deacon authored
commit 53290432 upstream. The syscall number may have been changed by a tracer, so we should pass the actual number in from the caller instead of pulling it from the saved r7 value directly. Cc: <stable@vger.kernel.org> Cc: Pi-Hsun Shih <pihsun@chromium.org> Reviewed-by:
Dave Martin <Dave.Martin@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Christoffer Dall authored
commit fb544d1c upstream. We recently addressed a VMID generation race by introducing a read/write lock around accesses and updates to the vmid generation values. However, kvm_arch_vcpu_ioctl_run() also calls need_new_vmid_gen() but does so without taking the read lock. As far as I can tell, this can lead to the same kind of race: VM 0, VCPU 0 VM 0, VCPU 1 ------------ ------------ update_vttbr (vmid 254) update_vttbr (vmid 1) // roll over read_lock(kvm_vmid_lock); force_vm_exit() local_irq_disable need_new_vmid_gen == false //because vmid gen matches enter_guest (vmid 254) kvm_arch.vttbr = <PGD>:<VMID 1> read_unlock(kvm_vmid_lock); enter_guest (vmid 1) Which results in running two VCPUs in the same VM with different VMIDs and (even worse) other VCPUs from other VMs could now allocate clashing VMID 254 from the new generation as long as VCPU 0 is not exiting. Attempt to solve this by making sure vttbr is updated before another CPU can observe the updated VMID generation. Cc: stable@vger.kernel.org Fixes: f0cf47d9 "KVM: arm/arm64: Close VMID generation race" Reviewed-by:
Julien Thierry <julien.thierry@arm.com> Signed-off-by:
Christoffer Dall <christoffer.dall@arm.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Vasily Averin authored
commit d4b09acf upstream. if node have NFSv41+ mounts inside several net namespaces it can lead to use-after-free in svc_process_common() svc_process_common() /* Setup reply header */ rqstp->rq_xprt->xpt_ops->xpo_prep_reply_hdr(rqstp); <<< HERE svc_process_common() can use incorrect rqstp->rq_xprt, its caller function bc_svc_process() takes it from serv->sv_bc_xprt. The problem is that serv is global structure but sv_bc_xprt is assigned per-netnamespace. According to Trond, the whole "let's set up rqstp->rq_xprt for the back channel" is nothing but a giant hack in order to work around the fact that svc_process_common() uses it to find the xpt_ops, and perform a couple of (meaningless for the back channel) tests of xpt_flags. All we really need in svc_process_common() is to be able to run rqstp->rq_xprt->xpt_ops->xpo_prep_reply_hdr() Bruce J Fields points that this xpo_prep_reply_hdr() call is an awfully roundabout way just to do "svc_putnl(resv, 0);" in the tcp case. This patch does not initialiuze rqstp->rq_xprt in bc_svc_process(), now it calls svc_process_common() with rqstp->rq_xprt = NULL. To adjust reply header svc_process_common() just check rqstp->rq_prot and calls svc_tcp_prep_reply_hdr() for tcp case. To handle rqstp->rq_xprt = NULL case in functions called from svc_process_common() patch intruduces net namespace pointer svc_rqst->rq_bc_net and adjust SVC_NET() definition. Some other function was also adopted to properly handle described case. Signed-off-by:
Vasily Averin <vvs@virtuozzo.com> Cc: stable@vger.kernel.org Fixes: 23c20ecd ("NFS: callback up - users counting cleanup") Signed-off-by:
J. Bruce Fields <bfields@redhat.com> v2: added lost extern svc_tcp_prep_reply_hdr() Signed-off-by:
-
Jan Stancek authored
commit 8ab88c71 upstream. LTP proc01 testcase has been observed to rarely trigger crashes on arm64: page_mapped+0x78/0xb4 stable_page_flags+0x27c/0x338 kpageflags_read+0xfc/0x164 proc_reg_read+0x7c/0xb8 __vfs_read+0x58/0x178 vfs_read+0x90/0x14c SyS_read+0x60/0xc0 The issue is that page_mapped() assumes that if compound page is not huge, then it must be THP. But if this is 'normal' compound page (COMPOUND_PAGE_DTOR), then following loop can keep running (for HPAGE_PMD_NR iterations) until it tries to read from memory that isn't mapped and triggers a panic: for (i = 0; i < hpage_nr_pages(page); i++) { if (atomic_read(&page[i]._mapcount) >= 0) return true; } I could replicate this on x86 (v4.20-rc4-98-g60b54823) only with a custom kernel module [1] which: - allocates compound page (PAGEC) of order 1 - allocates 2 normal pages (COPY), which are initialized to 0xff (to satisfy _mapcount >= 0) - 2 PAGEC page structs are copied to address of first COPY page - second page of COPY is marked as not present - call to page_mapped(COPY) now triggers fault on access to 2nd COPY page at offset 0x30 (_mapcount) [1] https://github.com/jstancek/reproducers/blob/master/kernel/page_mapped_crash/repro.c Fix the loop to iterate for "1 << compound_order" pages. Kirrill said "IIRC, sound subsystem can producuce custom mapped compound pages". Link: http://lkml.kernel.org/r/c440d69879e34209feba21e12d236d06bc0a25db.1543577156.git.jstancek@redhat.com Fixes: e1534ae9 ("mm: differentiate page_mapped() from page_mapcount() for compound pages") Signed-off-by:
Jan Stancek <jstancek@redhat.com> Debugged-by:
Laszlo Ersek <lersek@redhat.com> Suggested-by:
"Kirill A. Shutemov" <kirill@shutemov.name> Acked-by:
Michal Hocko <mhocko@suse.com> Acked-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by:
David Hildenbrand <david@redhat.com> Reviewed-by:
Andrea Arcangeli <aarcange@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Theodore Ts'o authored
commit 191ce178 upstream. The check for special (reserved) inode number checks in __ext4_iget() was broken by commit 8a363970: ("ext4: avoid declaring fs inconsistent due to invalid file handles"). This was caused by a botched reversal of the sense of the flag now known as EXT4_IGET_SPECIAL (when it was previously named EXT4_IGET_NORMAL). Fix the logic appropriately. Fixes: 8a363970 ("ext4: avoid declaring fs inconsistent...") Signed-off-by:
Theodore Ts'o <tytso@mit.edu> Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: stable@kernel.org Signed-off-by:
-
Theodore Ts'o authored
commit 95cb6713 upstream. We already using mapping_set_error() in fs/ext4/page_io.c, so all we need to do is to use file_check_and_advance_wb_err() when handling fsync() requests in ext4_sync_file(). Signed-off-by:
-
Theodore Ts'o authored
commit ad211f3e upstream. In no-journal mode, we previously used __generic_file_fsync() in no-journal mode. This triggers a lockdep warning, and in addition, it's not safe to depend on the inode writeback mechanism in the case ext4. We can solve both problems by calling ext4_write_inode() directly. Signed-off-by:
-
Theodore Ts'o authored
commit e8680786 upstream. The xfstests generic/475 test switches the underlying device with dm-error while running a stress test. This results in a large number of file system errors, and since we can't lock the buffer head when marking the superblock dirty in the ext4_grp_locked_error() case, it's possible the superblock to be !buffer_uptodate() without buffer_write_io_error() being true. We need to set buffer_uptodate() before we call mark_buffer_dirty() or this will trigger a WARN_ON. It's safe to do this since the superblock must have been properly read into memory or the mount would have been successful. So if buffer_uptodate() is not set, we can safely assume that this happened due to a failed attempt to write the superblock. Signed-off-by:
-
Theodore Ts'o authored
commit 2b08b1f1 upstream. The ext4_inline_data_fiemap() function calls fiemap_fill_next_extent() while still holding the xattr semaphore. This is not necessary and it triggers a circular lockdep warning. This is because fiemap_fill_next_extent() could trigger a page fault when it writes into page which triggers a page fault. If that page is mmaped from the inline file in question, this could very well result in a deadlock. This problem can be reproduced using generic/519 with a file system configuration which has the inline_data feature enabled. Signed-off-by:
-
Theodore Ts'o authored
commit 812c0cab upstream. There are enough credits reserved for most dioread_nolock writes; however, if the extent tree is sufficiently deep, and/or quota is enabled, the code was not allowing for all eventualities when reserving journal credits for the unwritten extent conversion. This problem can be seen using xfstests ext4/034: WARNING: CPU: 1 PID: 257 at fs/ext4/ext4_jbd2.c:271 __ext4_handle_dirty_metadata+0x10c/0x180 Workqueue: ext4-rsv-conversion ext4_end_io_rsv_work RIP: 0010:__ext4_handle_dirty_metadata+0x10c/0x180 ... EXT4-fs: ext4_free_blocks:4938: aborting transaction: error 28 in __ext4_handle_dirty_metadata EXT4: jbd2_journal_dirty_metadata failed: handle type 11 started at line 4921, credits 4/0, errcode -28 EXT4-fs error (device dm-1) in ext4_free_blocks:4950: error 28 Signed-off-by:
-
Ilya Dryomov authored
commit 85f5a4d6 upstream. There is a window between when RBD_DEV_FLAG_REMOVING is set and when the device is removed from rbd_dev_list. During this window, we set "already" and return 0. Returning 0 from write(2) can confuse userspace tools because 0 indicates that nothing was written. In particular, "rbd unmap" will retry the write multiple times a second: 10:28:05.463299 write(4, "0", 1) = 0 10:28:05.463509 write(4, "0", 1) = 0 10:28:05.463720 write(4, "0", 1) = 0 10:28:05.463942 write(4, "0", 1) = 0 10:28:05.464155 write(4, "0", 1) = 0 Cc: stable@vger.kernel.org Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Tested-by:
Dongsheng Yang <dongsheng.yang@easystack.cn> Signed-off-by:
-
Lyude Paul authored
commit 2d1af6a1 upstream. This is an ugly one unfortunately. Currently, all DRM drivers supporting atomic modesetting will save the state that userspace had set before suspending, then attempt to restore that state on resume. This probably worked very well at one point, like many other things, until DP MST came into the picture. While it's easy to restore state on normal display connectors that were disconnected during suspend regardless of their state post-resume, this can't really be done with MST because of the fact that setting up a downstream sink requires performing sideband transactions between the source and the MST hub, sending out the ACT packets, etc. Because of this, there isn't really a guarantee that we can restore the atomic state we had before suspend once we've resumed. This sucks pretty bad, but so far I haven't run into any compositors that this actually causes serious issues with. Most compositors will notice the hotplug we send afterwards, and then reprobe state. Since nouveau and i915 also don't fail the suspend/resume process due to failing to restore the atomic state, let's make amdgpu match this behavior. Better to resume the GPU properly, then to stop the process half way because of a potentially unavoidable atomic commit failure. Eventually, we'll have a real fix for this problem on the DRM level. But we've got some more important low-hanging fruit to deal with first. Signed-off-by:
Lyude Paul <lyude@redhat.com> Reviewed-by:
Harry Wentland <harry.wentland@amd.com> Cc: Jerry Zuo <Jerry.Zuo@amd.com> Cc: <stable@vger.kernel.org> # v4.15+ Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-3-lyude@redhat.comSigned-off-by:
-
Lyude Paul authored
commit fe7553be upstream. drm_dp_mst_topology_mgr_resume() returns whether or not it managed to find the topology in question after a suspend resume cycle, and the driver is supposed to check this value and disable MST accordingly if it's gone-in addition to sending a hotplug in order to notify userspace that something changed during suspend. Currently, amdgpu just makes the mistake of ignoring the return code from drm_dp_mst_topology_mgr_resume() which means that if a topology was removed in suspend, amdgpu never notices and assumes it's still connected which leads to all sorts of problems. So, fix this by actually checking the rc from drm_dp_mst_topology_mgr_resume(). Also, reformat the rest of the function while we're at it to fix the over-indenting. Signed-off-by:
-
Chris Wilson authored
commit 280d479b upstream. If we fail to pin the ggtt vma slot for the ppgtt page tables, we need to unwind the locals before reporting the error. Or else on subsequent attempts to bind the page tables into the ggtt, we will already believe that the vma has been pinned and continue on blithely. If something else should happen to be at that location, choas ensues. Fixes: a2bbf714 ("drm/i915/gtt: Only keep gen6 page directories pinned while active") Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com> Cc: Matthew Auld <matthew.william.auld@gmail.com> Cc: <stable@vger.kernel.org> # v4.19+ Reviewed-by:
Matthew Auld <matthew.william.auld@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20181222030623.21710-1-chris@chris-wilson.co.uk (cherry picked from commit d4de7535) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Ivan Mironov authored
commit 62d85b3b upstream. SDL 1.2 sets all fields related to the pixel format to zero in some cases[1]. Prior to commit db05c481 ("drm: fb-helper: Reject all pixel format changing requests"), there was an unintentional workaround for this that existed for more than a decade. First in device-specific DRM drivers, then here in drm_fb_helper.c. Previous code containing this workaround just ignores pixel format fields from userspace code. Not a good thing either, as this way, driver may silently use pixel format different from what client actually requested, and this in turn will lead to displaying garbage on the screen. I think that returning EINVAL to userspace in this particular case is the right option, so I decided to left code from problematic commit untouched instead of just reverting it entirely. Here is the steps required to reproduce this problem exactly: 1) Compile fceux[2] with SDL 1.2.15 and without GTK or OpenGL support. SDL should be compiled with fbdev support (which is on by default). 2) Create /etc/fb.modes with following contents (values seems not used, and just required to trigger problematic code in SDL): mode "test" geometry 1 1 1 1 1 timings 1 1 1 1 1 1 1 endmode 3) Create ~/.fceux/fceux.cfg with following contents: SDL.Hotkeys.Quit = 27 SDL.DoubleBuffering = 1 4) Ensure that screen resolution is at least 1280x960 (e.g. append "video=Virtual-1:1280x960-32" to the kernel cmdline for qemu/QXL). 5) Try to run fceux on VT with some ROM file[3]: # ./fceux color_test.nes [1] SDL 1.2.15 source code, src/video/fbcon/SDL_fbvideo.c, FB_SetVideoMode() [2] http://www.fceux.com [3] Example ROM: https://github.com/bokuweb/rustynes/blob/master/roms/color_test.nesReported-by:
saahriktu <mail@saahriktu.org> Suggested-by:
Ivan Mironov <mironov.ivan@gmail.com> [danvet: Delete misleading comment.] Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20190108072353.28078-2-mironov.ivan@gmail.com Link: https://patchwork.freedesktop.org/patch/msgid/20190108072353.28078-2-mironov.ivan@gmail.comSigned-off-by:
-
Neil Armstrong authored
commit 4be9bd10 upstream. Since "drm/fb: Stop leaking physical address", the default behaviour of the DRM fbdev emulation is to set the smem_base to 0 and pass the new FBINFO_HIDE_SMEM_START flag. The main reason is to avoid leaking physical addresse to user-space, and it follows a general move over the kernel code to avoid user-space to manipulate physical addresses and then use some other mechanisms like dma-buf to transfer physical buffer handles over multiple subsystems. But, a lot of devices depends on closed sources binaries to enable OpenGL hardware acceleration that uses this smem_start value to pass physical addresses to out-of-tree modules in order to render into these physical adresses. These should use dma-buf buffers allocated from the DRM display device instead and stop relying on fbdev overallocation to gather DMA memory (some HW vendors delivers GBM and Wayland capable binaries, but older unsupported devices won't have these new binaries and are doomed until an Open Source solution like Lima finalizes). Since these devices heavily depends on this kind of software and because the smem_start population was available for years, it's a breakage to stop leaking smem_start without any alternative solutions. This patch adds a Kconfig depending on the EXPERT config and an unsafe kernel module parameter tainting the kernel when enabled. A clear comment and Kconfig help text was added to clarify why and when this patch should be reverted, but in the meantime it's a necessary feature to keep. Cc: Dave Airlie <airlied@gmail.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Cc: Noralf Trønnes <noralf@tronnes.org> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Eric Anholt <eric@anholt.net> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Rob Clark <robdclark@gmail.com> Cc: Ben Skeggs <skeggsb@gmail.com> Cc: Christian König <christian.koenig@amd.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Reviewed-by:
Maxime Ripard <maxime.ripard@bootlin.com> Tested-by:
Dave Airlie <airlied@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/1538136355-15383-1-git-send-email-narmstrong@baylibre.comSigned-off-by:
-
Jerry (Fangzhi) Zuo authored
commit 8c9d90ee upstream. Need to blank stream before deallocate MST payload. [drm:generic_reg_wait [amdgpu]] *ERROR* REG_WAIT timeout 10us * 3000 tries - dce110_stream_encoder_dp_blank line:944 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 2201 at /var/lib/dkms/amdgpu/18.50-690240/build/amd/amdgpu/../display/dc/dc_helper.c:249 generic_reg_wait+0xe7/0x160 [amdgpu] Call Trace: dce110_stream_encoder_dp_blank+0x11c/0x180 [amdgpu] core_link_disable_stream+0x40/0x230 [amdgpu] ? generic_reg_update_ex+0xdb/0x130 [amdgpu] dce110_reset_hw_ctx_wrap+0xb7/0x1f0 [amdgpu] dce110_apply_ctx_to_hw+0x30/0x430 [amdgpu] ? dce110_apply_ctx_for_surface+0x206/0x260 [amdgpu] dc_commit_state+0x2ba/0x4d0 [amdgpu] amdgpu_dm_atomic_commit_tail+0x297/0xd70 [amdgpu] ? amdgpu_bo_pin_restricted+0x58/0x260 [amdgpu] ? wait_for_completion_timeout+0x1f/0x120 ? wait_for_completion_interruptible+0x1c/0x160 commit_tail+0x3d/0x60 [drm_kms_helper] drm_atomic_helper_commit+0xf6/0x100 [drm_kms_helper] drm_atomic_connector_commit_dpms+0xe5/0xf0 [drm] drm_mode_obj_set_property_ioctl+0x14f/0x250 [drm] drm_mode_connector_property_set_ioctl+0x2e/0x40 [drm] drm_ioctl+0x1e0/0x430 [drm] ? drm_mode_connector_set_obj_prop+0x70/0x70 [drm] ? ep_read_events_proc+0xb0/0xb0 ? ep_scan_ready_list.constprop.18+0x1e6/0x1f0 ? timerqueue_add+0x52/0x80 amdgpu_drm_ioctl+0x49/0x80 [amdgpu] do_vfs_ioctl+0x90/0x5f0 SyS_ioctl+0x74/0x80 do_syscall_64+0x74/0x140 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 ---[ end trace 3ed7b77a97d60f72 ]--- Signed-off-by:
Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com> Reviewed-by:
Hersen Wu <hersenxs.wu@amd.com> Acked-by:
Alex Deucher <alexander.deucher@amd.com> Tested-by:
-
Marc Zyngier authored
commit 3f7bb2ec upstream. The write to the status register is really an ACK for the HW, and should be treated as such by the driver. Let's move it to the irq_ack() callback, which will prevent people from moving it around in order to paper over other bugs. Fixes: 8c934095 ("PCI: dwc: Clear MSI interrupt status after it is handled, not before") Fixes: 7c5925af ("PCI: dwc: Move MSI IRQs allocation to IRQ domains hierarchical API") Link: https://lore.kernel.org/linux-pci/20181113225734.8026-1-marc.zyngier@arm.com/Reported-by:
Trent Piepho <tpiepho@impinj.com> Tested-by:
Niklas Cassel <niklas.cassel@linaro.org> Tested-by:
Gustavo Pimentel <gustavo.pimentel@synopsys.com> Tested-by:
Stanimir Varbanov <svarbanov@mm-sol.com> Signed-off-by:
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Marc Zyngier authored
commit fce5423e upstream. Bizarrely, there is no lock taken in the irq_ack() helper. This puts the ACK callback provided by a specific platform in a awkward situation where there is no synchronization that would be expected on other callback. Introduce the required lock, giving some level of uniformity among callbacks. Fixes: 7c5925af ("PCI: dwc: Move MSI IRQs allocation to IRQ domains hierarchical API") Link: https://lore.kernel.org/linux-pci/20181113225734.8026-1-marc.zyngier@arm.com/Tested-by:
-
Marc Zyngier authored
commit 830920e0 upstream. The dwc driver is showing an interesting level of brokeness, as it insists on using the enable/disable set of registers to mask/unmask MSIs, meaning that an MSIs being generated while the interrupt is in that "disabled" state will simply be lost. Let's move to the mask/unmask set of registers, which offers the expected semantics. Fixes: 7c5925af ("PCI: dwc: Move MSI IRQs allocation to IRQ domains hierarchical API") Link: https://lore.kernel.org/linux-pci/20181113225734.8026-1-marc.zyngier@arm.com/Tested-by:
-
Alex Deucher authored
commit f6653a0e upstream. Add a new pci id. Reviewed-by:
Leo Liu <leo.liu@amd.com> Signed-off-by:
-
Alex Williamson authored
commit 58fec830 upstream. The below referenced commit adds a test for integer overflow, but in doing so prevents the unmap ioctl from ever including the last page of the address space. Subtract one to compare to the last address of the unmap to avoid the overflow and wrap-around. Fixes: 71a7d3d7 ("vfio/type1: silence integer overflow warning") Link: https://bugzilla.redhat.com/show_bug.cgi?id=1662291 Cc: stable@vger.kernel.org # v4.15+ Reported-by:
Pei Zhang <pezhang@redhat.com> Debugged-by:
Peter Xu <peterx@redhat.com> Reviewed-by:
Cornelia Huck <cohuck@redhat.com> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
