This reverts one change from 67fa1062
that prevented userspace from seing the "driver disk" lun in a san disk
device.  The kernel shouldn't do this, it's up to userspace to handle
this properly, if it somehow wants to filter this away.


Cc: Ben Collins <bcollins@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Phil Dibowitz <phil@ipom.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The OHCI IRQ handler has an optimisation that avoids reading some
chip registers when the controller reports that the interrupt was
triggered *only* because completed requests were written into the
controller's "done list" and handed to the host.

This mechanism can't be used on some controllers.  Among others, it
fails for the SA1111 and the AMCC 440EP PowerPC processor.

This patch removes the optimisation and makes the code clearer.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Correct hanging while disconnecting the USB device cable.  Prevent a race
between vbus and UDP interrupts.  This bug was tracked on at91sam9260ek
boards.

A usb resume interrupt was firing after the vbus interrupt : the IP was
then already stoped and not able to deal with it (no more clock).  A simple
interrupt disabling is ok as the "end of bus reset" irq is non maskable and
ok to resume the USB device IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Host controller IRQs are supposed to be serviced with interrupts
disabled.  This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it.  It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().

This fixes Bugzilla #9335.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch (as1027) replaces a call to flush_scheduled_work() -- a
dangerous routine to invoke, especially while holding any sort of lock
-- with calls to cancel_work_sync() and cancel_delayed_work_sync().

This fixes Bugzilla #9532.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix kernel-doc warning in usb.h:
Warning(linux-2.6.24-rc3-git7//include/linux/usb.h:166): No description found for parameter 'sysfs_files_created'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This fixes a bunch of problems we are having with the Huawei devices...
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This adds a device ID for the Aerocomm Radio Modem, which uses the
cp2102.  I'm sure changing num_bulk_in/num_bulk_out to NUM_DONT_CARE
is the wrong fix, but this is the only device I have with a cp2102,
so I have no idea what a good global value would be, if there is one.
Zero didn't work with this device.

From: Jeff Long <JeffLong@mitre.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When a device cannot handle the smallest previously limited transfer
size (64 blocks) without stalling, limit the device to the amount of
packets that fit in a platform native page.

The lowest possible limit is PAGE_CACHE_SIZE, so if the device is ever
used on a platform that has larger than 8K pages, you lose unless you
can convince the device firmware folks to fix the issue.

Cc: Mathew Dharm <mdharm-scsi@one-eyed-alien.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Doug Maxey <dwm@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Attached is a patch to fix the addition of the new product ids I sent.

It is against 2.6.24-rc4, as Linus included the broken version of the
patch I sent you in that tree. :(

Not sure if this is the right method to go about this, but hopefully I got
it right this time.
Signed-off-by: Andrew Gilmore <agilmore@wirelessbeehive.com>
CC: Kevin Lloyd <klloyd@sierrawireless.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Fix endless loop in cheetah_xcall_deliver().
  [SERIAL] sparc: Infrastructure to fix section mismatch bugs.

* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
  i2c/isp1301_omap: Build fix
  i2c: Add missing spaces in split log messages
  i2c-gpio: Initialize adapter class
  i2c: Delete an outdated piece of documentation

We need to mask out the proper bits when testing the dispatch status
register else we can see unrelated NACK bits from previous cross call
sends.
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch against 2.6.23 sparc-2.6.git contains a number of minor
cleanups of the sparc serial drivers.  Initially I fixed this build
warning:

WARNING: vmlinux.o(.text+0x107a2c): Section mismatch: reference to .init.text:add_preferred_console (between 'sunserial_console_match' and 'sunserial_console_termios')

which is done by declaring sunserial_console_match() as __init.  This
resulted in build warnings on sunserial_current_minor.  To resolve
these the variable was changed so it is no longer global, and to hide
operations on it inside 2 new functions. These functions handle the
UART minor handling code that is common to all sparc serial drivers.

These changes allowed to clean up the uart counters in all the sparc
serial drivers, and the administration of minor device numbers.

Lastly, sunserial_console_termios() does not need to be exported since
it is only called from non-modular code.

Sadly, the following build warning still exists:

WARNING: vmlinux.o(__ksymtab+0x2910): Section mismatch: reference to .init.text:sunserial_console_match (between '__ksymtab_sunserial_console_match' and '__ksymtab_sunserial_unregister_minors')

This could be resolved by not exporting sunserial_console_match(), but
this is not possible at the moment because it is being called from
modular code. On the other hand, this is a bogus warning since it
comes from a ksymtab section.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Build fix to the isp1301_omap driver ... this driver gets built
more often in the OMAP tree than in mainline, partly because the
defconfig for H2 (plus probably H3 and H4) needs updating.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

This is required to let hwmon drivers attach to the adapter.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

I'm amazed that this old piece of documentation managed to survive
until today.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

videobuf_dvb needs videobuf_read_start. The EXPORT_SYMBOL_GPL() were removed by
a previous patch. However, videobuf_dvb needs this.

This patch re-adds videobuf_read_start, doing the proper lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This reverts commit 70eba18b, as per
Jeff Garzik:

   "That was meant for 2.6.25, and actually (due to patching) applied to
    a completely unrelated 2.6.24 net driver."
Noted-by: Roland Dreier <rdreier@cisco.com>
Requested-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:

<--  snip  -->

...
...

<--  snip  -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:

<--  snip  -->

...
...

<--  snip  -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

As reported by Andrew Morton:

> ERROR: "dibusb_dib3000mc_frontend_attach" [drivers/media/dvb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
> ERROR: "dibusb_dib3000mc_tuner_attach" [drivers/media/dvb/dvb-usb/dvb-usb-nova-t-usb2.ko] undefined!
> ERROR: "dibusb_dib3000mc_frontend_attach" [drivers/media/dvb/dvb-usb/dvb-usb-dibusb-mc.ko] undefined!
> ERROR: "dibusb_dib3000mc_tuner_attach" [drivers/media/dvb/dvb-usb/dvb-usb-dibusb-mc.ko] undefined!
> ERROR: "dibusb_dib3000mc_frontend_attach" [drivers/media/dvb/dvb-usb/dvb-usb-a800.ko] undefined!
> ERROR: "dibusb_dib3000mc_tuner_attach" [drivers/media/dvb/dvb-usb/dvb-usb-a800.ko] undefined
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

On Tue, 4 Dec 2007, Ingo Molnar wrote:

>  drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
>  : undefined reference to `dib3000mc_get_tuner_i2c_master'
>  drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
>  : undefined reference to `dib3000mc_set_config'

Seems like -common part contains also code that is not completely
common to all the modules.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

cxusb needs tuner-xc2028*.h files, but Makefile is not adding its patch

drivers/media/dvb/dvb-usb/cxusb.c:33:26: error: tuner-xc2028.h: File not found
drivers/media/dvb/dvb-usb/cxusb.c:34:32: error: tuner-xc2028-types.h: File not found
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

There are several months my hvr1110 stop working.
This is very simple to fix, for my card revision at least, by setting a
missing field to the hauppauge_hvr_1110_config.
Signed-off-by: Benoit Istin <beistin@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This is pretty serious bug.  map->count is never initialized after the
call to kmalloc making the count start at some random trash value.  The
end result is leaking videobufs.

Also, fix up the debug statements to print unsigned values.

Pushed to http://ifup.org/hg/v4l-dvb too
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The saa7134 video driver starts dropping frames when used together with the
saa7134-alsa driver. Frames are dropped because when an audio event is waiting
the driver simply ignores the interrupt and passes it on to the saa7134-alsa
interrupt handler. The alsa interrupt handler in turn acknowledges all types
of events thus clearing the pending video events as well. Fix by only masking
out the audio event in the video interrupt handler and by only acknowledging
the audio event in the alsa driver.
Signed-off-by: Heikki Lindholm  <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The vmux for composite over s-video input was wrong.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Complement va_start() with va_end() + minor style fixes in the same function.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The period handling in saa7134-alsa is broken in two ways. First, the
minimum number of periods of two does not work, because the dma is setup
two periods ahead in the irq handler. Fix the minimum to four periods.
Second, the code assumes that the number of periods is divisible by two,
which isn't always the case on ALSA. Fix by adding a constraint.
Signed-off-by: Heikki Lindholm  <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The default adc_clock for the zl10353 is different from what was originally
thought to be the case and the TRL nominal rate formula was incorrect as a
result.  Use a better (and hopefully now correct) formula.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Fallout from videobuf_mmap_setup() locking fixes.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Drivers were using cookie cutter code for stopping the read/stream.  Use the
new videobuf_stop function which is lock safe.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

- Add comments to functions that require that caller hold q->lock
- Add __videobuf_mmap_free that doesn't hold q->lock for use within videobuf
- Add locking to videobuf_mmap_free
- Fix linux/drivers/media/common/saa7146_video.c which was holding lock around
  videobuf_read_stop
- Add locking to functions that operate on a queue
- Add videobuf_stop to take care of stopping in both the read and stream case

TODO: bttv still has an unsafe call to videobuf_queue_is_busy
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

This is a modified version of a patch previously posted by Thomas
Unverzagt.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Thanks to Markus Reichberger to point this.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

The attached patch is required so that the autodetecion code also works after
a reboot.

Setting the I2C speed does not seem to be supported for em2800.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>