- 25 Apr, 2011 13 commits
-
-
Vasanthakumar Thiagarajan authored
Use hw supported chains instead of hard coded values. Signed-off-by:
Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Add a bool in ath9k_platform_data to pass AHB clock speed information. Driver needs this to configure PLL on some SOCs. Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
Vasanthakumar Thiagarajan authored
Signed-off-by:
-
John W. Linville authored
Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6
-
-
- 22 Apr, 2011 10 commits
-
-
Johannes Berg authored
This variable is only ever checked right after the function that sets it, but the same function will also return the status, so we can pass it through instead of checking hw_ready later. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Wey-Yi Guy <wey-yi.w.guy@intel.com>
-
Johannes Berg authored
On new hardware, ucode images always come in pairs: code and data. Therefore, combine the variables into an appropriate struct and use that when both code and data are needed. Also, combine allocation and copying so that we have less code in total. Signed-off-by:
-
Johannes Berg authored
The current firmware loading mechanism in iwlwifi is very hard to follow, and thus hard to maintain. To make it easier, make the firmware loading synchronous. For now, as a side effect, this removes a number of retry possibilities we had. It isn't typical for this to fail, but if it does happen we restart from scratch which this also makes easier to do should it be necessary. Signed-off-by:
-
Johannes Berg authored
When the firmware encounters an error while the driver is waiting for a notification, it will never get that notification. Therefore, instead of timing out, bail out on errors when waiting for notifications. Signed-off-by:
-
Johannes Berg authored
We're unlikely to care about the actual time spent waiting, so make the function return an error code which is less error prone in coding new uses. Also, while at it, mark __must_check. Signed-off-by:
-
Johannes Berg authored
A notification wait function is called with the command, but currently has no way of passing data back to the caller -- fix that by adding a void pointer to the function that can be used between the caller and the function. Signed-off-by:
-
Johannes Berg authored
Starting the device consists of many things, refactor out enabling the hardware and also return -ERFKILL when the rfkill signal is found to be asserted (which makes more sense anyway, but is also required now to make the __iwl_up function return right away.) Signed-off-by:
-
Johannes Berg authored
The iwl_down path really consists of multiple things, refactor out the hardware resetting (including, of course, related software state like irqs). Signed-off-by:
-
Johannes Berg authored
There's no point in running through iwl_down() when we never registered with mac80211, as it just cleans up internal structures that were never initialised in this case. Therefore we can also remove the special handling for this case from __iwl_down(). Signed-off-by:
-
Johannes Berg authored
The current code to read the error table header just hardcodes all the offsets, which is a bit hard to understand. We can read in the entire header (as much as we need) into a structure, and then take the data from there, which makes it easier to understand. To read a bigger blob we also don't need to grab NIC access for each word read, making the code more efficient. Signed-off-by:
-
- 19 Apr, 2011 17 commits
-
-
Johannes Berg authored
Apparently this was confusing still ... add a note that the byte is needed as padding. Signed-off-by:
-
Ivo van Doorn authored
Implement the get_antenna and set_antenna callback functions, which will allow clients to control the antenna for all non-11n hardware (Antenna handling in rt2800 is still a bit magical, so we can't use the set_antenna for those drivers yet). To best support the set_antenna callback some modifications are needed in the diversity handling. We should never look at the default antenna settings to determine if software diversity is enabled. Instead we should set the diversity flag when possible, which will allow the link_tuner to automatically pick up the tuning. Signed-off-by:
Ivo van Doorn <IvDoorn@gmail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
-
Ivo van Doorn authored
With the get_ringparam callback function we can export ring parameters to ethtool through the mac80211 interface. Signed-off-by:
-
Ivo van Doorn authored
All register reads/writes in rt2800usb were previously done with rt2800_register_read/rt2800_register_write. These however indirectly call rt2x00usb_register_read/rt2x00usb_register_write which adds an additional overhead of at least one call and several move instructions to each register access. Replacing the calls to rt2800_register_read/rt2800_register_write with direct calls to rt2x00usb_register_read/rt2x00usb_register_write gets rid of quite a number of instructions in the drivers hotpaths (IRQ handling and txdone handling). For consistency replace all references to rt2800_register_read/write with the rt2x00usb_register_read/write variants. Signed-off-by:
-
Helmut Schaa authored
All register reads/writes in rt2800pci were previously done with rt2800_register_read/rt2800_register_write. These however indirectly call rt2x00pci_register_read/rt2x00pci_register_write which adds an additional overhead of at least one call and several move instructions to each register access. Replacing the calls to rt2800_register_read/rt2800_register_write with direct calls to rt2x00pci_register_read/rt2x00pci_register_write gets rid of quite a number of instructions in the drivers hotpaths (IRQ handling and txdone handling). For consistency replace all references to rt2800_register_read/write with the rt2x00pci_register_read/write variants. Signed-off-by:
Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by:
-
Gertjan van Wingerde authored
The two functions that are in rt2x00ht.c can be much better placed closer to the places where the call-sites of these functions are (one in rt2x00config.c and one in rt2x00queue.c) allowing us to make these functions static. Also, conditional compilations doesn't seem to be necessary anymore as 802.11n support is quite common nowadays. This makes the code a bit easier readable and searchable. Signed-off-by:
-
Gertjan van Wingerde authored
Code seems to be feature-complete, so no reason to not enable these devices by default. Also, remove the sentence about the support for these devices being non-functional. Signed-off-by:
-
Gertjan van Wingerde authored
The rt33xx devices support for both PCI and USB devices has been in the tree for a couple of months now, and seems to be functional and not in a worse shape than the support for rt28xx and rt30xx devices. No longer mark it as experimental and enable the support for these devices by default. Signed-off-by:
-
Gertjan van Wingerde authored
Add USB IDs that are listed in the latest Ralink Windows and/or Linux drivers. Signed-off-by:
-
Gertjan van Wingerde authored
Both USB and PCI drivers allow a system administrator to dynamically add USB/PCI IDs to the device table that a driver supports via the /sys/bus/{usb,pci,pci_express}/drivers/<driver-name>/new_id files. However, for the rt2x00 drivers using this method currently crashes the system with a NULL pointer failure. This is due to the set-up of rt2x00 where the probe functions require a rt2x00_ops structure in the driver_info field of the probed device. As this field is empty for the dynamically added devices this fails for these devices. Fix this by introducing driver-specific probe wrappers that do nothing but calling the bus-specific probe functions with the rt2x00_ops structure as an argument, rather than depending on the driver_info field. Signed-off-by: -
Gertjan van Wingerde authored
Move the USB ID entry from the unknown devices to the list of RT35xx based devices. Signed-off-by:
-
Helmut Schaa authored
This allows the compiler to perform the necessary bitfield calculations during compile time instead of run time and thus reduces the number of instructions to run during each tasklet invocation. This should improve performance in the RX hotpath. This comes at the cost of a slight increase in the module size (for example rt2800pci): Before: text data bss dec hex filename 14133 832 4 14969 3a79 drivers/net/wireless/rt2x00/rt2800pci.ko After: text data bss dec hex filename 14149 832 4 14985 3a89 drivers/net/wireless/rt2x00/rt2800pci.ko Signed-off-by:
-
Ivo van Doorn authored
When powersaving is enabled, assocaition times are very high (for WPA2 networks, the time can easily be around the 3 seconds). This is caused, because the flushing of the queues takes too much time. Without the flushing callback mac80211 assumes a timeout of 100ms while scanning. Limit all flush waiting loops to the same maximum. We can apply this maximum by passing the drop status to the driver, which makes sure the driver performs extra actions during the waiting for the queue to become empty. After these changes, association times fall within the healthy range of ~0.6 seconds with powersaving enabled. The difference between association time between powersaving enabled and disabled is now only ~0.1 second (which can also be due to the measuring method). Signed-off-by:
-
Johannes Stezenbach authored
TX status is reported by the hardware when a packet has been sent (or after TX failed after possible retries), which is some time after the DMA completion. Since the rt2800usb hardware can not signal interrupts we have to use a timer, otherwise the TX status would only be read by the next packet's TX DMA completion, or by the watchdog thread. Signed-off-by:
Johannes Stezenbach <js@sig21.net> Signed-off-by:
-
Johannes Stezenbach authored
The watchdog just triggers rt2800usb_work_txdone() when it detects a TX status timeout, thus rt2800usb_work_txdone() needs to handle this case. Signed-off-by:
-
Johannes Stezenbach authored
Add a timestamp to each queue entry which is updated whenever the status of the entry changes, and remove the per-queue timestamps. The previous check was incorrect and caused both false positives and false negatives. With the corrected check it comes apparent that the TX status usually times out on rt2800usb unless there is sufficient traffic (i.e. the next TX will complete the previous TX status). Signed-off-by:
-
Johannes Stezenbach authored
Trying to fix the "TX status report missed" warnings by reading the TX_STA_FIFO entries as quickly as possible. The TX_STA_FIFO is too small in hardware, thus reading it only from the workqueue is too slow and entries get lost. Start an asynchronous read of the TX_STA_FIFO directly from the TX URB completion callback (atomic context, thus it cannot use the blocking rt2800_register_read()). If the async read returns a valid FIFO entry, it is pushed into a larger FIFO inside struct rt2x00_dev, until rt2800_txdone() picks it up. A .tx_dma_done callback is added to struct rt2x00lib_ops to trigger the async read from the URB completion callback. Signed-off-by:
-
