Pull GPIO updates from Linus Walleij:
 "Here is the bulk of GPIO changes for the v4.4 development cycle.

  The only changes hitting outside drivers/gpio are in the pin control
  subsystem and these seem to have settled nicely in linux-next.

  Development mistakes and catfights are nicely documented in the
  reverts as you can see.  The outcome of the ABI fight is that we're
  working on a chardev ABI for GPIO now, where hope to show results for
  the v4.5 kernel.

  Summary of changes:

  GPIO core:
   - Define and handle flags for open drain/open collector and open
     source/open emitter, also know as "single-ended" configurations.
   - Generic request/free operations that handle calling out to the
     (optional) pin control backend.
   - Some refactoring related to an ABI change that did not happen, yet
     provide useful.
   - Added a real-time compliance checklist.  Many GPIO chips have
     irqchips, and need to think this over with the RT patches going
     upstream.
   - Restructure, fix and clean up Kconfig menus a bit.

  New drivers:
   - New driver for AMD Promony.
   - New driver for ACCES 104-IDIO-16, a port-mapped I/O card,
     ISA-style.  Very retro.

  Subdriver changes:
   - OMAP changes to handle real time requirements.
   - Handle trigger types for edge and level IRQs on PL061 properly.  As
     this hardware is very common it needs to set a proper example for
     others to follow.
   - Some container_of() cleanups.
   - Delete the unused MSM driver in favor of the driver that is
     embedded inside the pin control driver.
   - Cleanup of the ath79 GPIO driver used by many, many OpenWRT router
     targets.
   - A consolidated IT87xx driver replacing the earlier very specific
     IT8761e driver.
   - Handle the TI TCA9539 in the PCA953x driver.  Also handle ACPI
     devices in this subdriver.
   - Drop xilinx arch dependencies as these FPGAs seem to profilate over
     a few different architectures.  MIPS and ARM come to mind"

* tag 'gpio-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (57 commits)
  gpio: fix up SPI submenu
  gpio: drop surplus I2C dependencies
  gpio: drop surplus X86 dependencies
  gpio: dt-bindings: document the official use of "ngpios"
  gpio: MAINTAINERS: Add an entry for the ATH79 GPIO driver
  gpio / ACPI: Allow shared GPIO event to be read via operation region
  gpio: group port-mapped I/O drivers in a menu
  gpio: Add ACCES 104-IDIO-16 driver maintainer entry
  gpio: zynq: Document interrupt-controller DT binding
  gpio: xilinx: Drop architecture dependencies
  gpio: generic: Revert to old error handling in bgpio_map
  gpio: add a real time compliance notes
  Revert "gpio: add a real time compliance checklist"
  gpio: Add GPIO support for the ACCES 104-IDIO-16
  gpio: driver for AMD Promontory
  gpio: xlp: Convert to use gpiolib irqchip helpers
  gpio: add a real time compliance checklist
  gpio/xilinx: enable for MIPS
  gpiolib: Add and use OF_GPIO_SINGLE_ENDED flag
  gpiolib: Split GPIO flags parsing and GPIO configuration
  ...

Pull pin control updates from Linus Walleij:
 "This is the big bulk of pin control changes for the v4.4 kernel
  development cycle.  Development pace is high in pin control again this
  merge window.  28 contributors, 83 patches.

  It hits a few sites outside the pin control subsystem:

   - Device tree bindings in Documentation (as usual)
   - MAINTAINERS
   - drivers/base/* for the "init" state handling by Doug Anderson.
     This has been ACKed by Greg.
   - drivers/usb/renesas_usbhs/rcar2.c, for a dependent Renesas change
     in the USB subsystem.  This has been ACKed by both Greg and Felipe.
   - arch/arm/boot/dts/sama5d2.dtsi - this should ideally have gone
     through the ARM SoC tree but ended up here.

  This time I am using Geert Uytterhoeven as submaintainer for SH PFC
  since the are three-four people working in parallel with new Renesas
  ASICs.

  Summary of changes:

  Infrastructure:

   - Doug Anderson wrote a patch adding an "init" state different from
     the "default" state for pin control state handling in the core
     framework.  This is applied before the driver's probe() call if
     defined and takes precedence over "default".  If both are defined,
     "init" will be applied *before* probe() and "default" will be
     applied *after* probe().

  Significant subdriver improvements:

   - SH PFC is switched to getting GPIO ranges from the device tree
     ranges property on DT platforms.
   - Got rid of CONFIG_ARCH_SHMOBILE_LEGACY, we are all modernized.
   - Got rid of SH PFC hardcoded IRQ numbers.
   - Allwinner sunxi external interrupt through the "r" controller.
   - Moved the Cygnus driver to use DT-provided GPIO ranges.

  New drivers:

   - Atmel PIO4 pin controller for the SAMA4D2 family

  New subdrivers:

   - Rockchip RK3036 subdriver
   - Renesas SH PFC R8A7795 subdriver
   - Allwinner sunxi A83T PIO subdriver
   - Freescale i.MX7d iomux lpsr subdriver
   - Marvell Berlin BG4CT subdriver
   - SiRF Atlas 7 step B SoC subdriver
   - Intel Broxton SoC subdriver

  Apart from this, the usual slew if syntactic and semantic fixes"

* tag 'pinctrl-v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (81 commits)
  pinctrl: pinconf: remove needless loop
  pinctrl: uniphier: guard uniphier directory with CONFIG_PINCTRL_UNIPHIER
  pinctrl: zynq: fix UTF-8 errors
  pinctrl: zynq: Initialize early
  pinctrl: at91: add missing of_node_put
  pinctrl: tegra-xusb: Correct lane mux options
  pinctrl: intel: Add Intel Broxton pin controller support
  pinctrl: intel: Allow requesting pins which are in ACPI mode as GPIOs
  pinctrl: intel: Add support for multiple GPIO chips sharing the interrupt
  drivers/pinctrl: Add the concept of an "init" state
  pinctrl: uniphier: set input-enable before pin-muxing
  pinctrl: cygnus: Add new compatible string for gpio controller driver
  pinctrl: cygnus: Remove GPIO to Pinctrl pin mapping from driver
  pinctrl: cygnus: Optional DT property to support pin mappings
  pinctrl: sunxi: Add irq pinmuxing to sun6i "r" pincontroller
  pinctrl: sunxi: Fix irq_of_xlate for the r_pio pinctrl block
  pinctrl: sh-pfc: Remove obsolete r8a7778 platform_device_id entry
  pinctrl: sh-pfc: Remove obsolete r8a7779 platform_device_id entry
  pinctrl: sh-pfc: Stop including <linux/platform_data/gpio-rcar.h>
  usb: renesas_usbhs: Remove unneeded #include <linux/platform_data/gpio-rcar.h>
  ...

Pull EDAC updates from Borislav Petkov:
 "A bunch of fixes all over the place and some hw enablement this time.

   - Convert EDAC to debugfs wrappers and make drivers use those
     (Borislav Petkov)

   - L3 and SoC support for xgene_edac (Loc Ho)

   - AMD F15h, models 0x60-6f support to amd64_edac (Aravind
     Gopalakrishnan)

   - Fixes and cleanups all over the place"

* tag 'edac_for_4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (22 commits)
  EDAC: Fix PAGES_TO_MiB macro misuse
  EDAC, altera: SoCFPGA EDAC should not look for ECC_CORR_EN
  EDAC: Use edac_debugfs_remove_recursive()
  EDAC, ppc4xx_edac: Fix module autoload for OF platform driver
  Documentation/EDAC: Add reference documents section for amd64_edac
  EDAC, amd64_edac: Update copyright and remove changelog
  EDAC, amd64_edac: Extend scrub rate support to F15hM60h
  EDAC: Don't allow empty DIMM labels
  EDAC: Fix sysfs dimm_label store operation
  EDAC: Fix sysfs dimm_label show operation
  arm64, EDAC: Add L3/SoC DT subnodes to the APM X-Gene SoC EDAC node
  EDAC, xgene: Add SoC support
  EDAC, xgene: Fix possible sprintf() overflow issue
  EDAC, xgene: Add L3 support
  EDAC, Documentation: Update X-Gene EDAC binding for L3/SoC subnodes
  EDAC, sb_edac: Fix TAD presence check for sbridge_mci_bind_devs()
  EDAC, ghes_edac: Remove redundant memory_type array
  EDAC, xgene: Convert to debugfs wrappers
  EDAC, i5100: Convert to debugfs wrappers
  EDAC, altera: Convert to debugfs wrappers
  ...

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Add new API to set VCCQ voltage - mmc_regulator_set_vqmmc()
   - Add new ioctl to allow userspace to send multi commands
   - Wait for card busy signalling before starting SDIO requests
   - Remove MMC_CLKGATE
   - Enable tuning for DDR50 mode
   - Some code clean-up/improvements to mmc pwrseq
   - Use highest priority for eMMC restart handler
   - Add DT bindings for eMMC hardware reset support
   - Extend the mmc_send_tuning() API
   - Improve ios show for debugfs
   - A couple of code optimizations

  MMC host:
   - Some generic OF improvements
   - Various code clean-ups
   - sirf: Add support for DDR50
   - sunxi: Add support for card busy detection
   - mediatek: Use MMC_CAP_RUNTIME_RESUME
   - mediatek: Add support for eMMC HW-reset
   - mediatek: Add support for HS400
   - dw_mmc: Convert to use the new mmc_regulator_set_vqmmc() API
   - dw_mmc: Add external DMA interface support
   - dw_mmc: Some various improvements
   - dw_mmc-rockchip: MMC tuning with the clock phase framework
   - sdhci: Properly clear IRQs during resume
   - sdhci: Enable tuning for DDR50 mode
   - sdhci-of-esdhc: Use IRQ mode for card detection
   - sdhci-of-esdhc: Support both BE and LE host controller
   - sdhci-pci: Build o2micro support in the same module
   - sdhci-pci: Support for new Intel host controllers
   - sdhci-acpi: Support for new Intel host controllers"

* tag 'mmc-v4.4' of git://git.linaro.org/people/ulf.hansson/mmc: (73 commits)
  mmc: dw_mmc: fix the wrong setting for UHS-DDR50 mode
  mmc: dw_mmc: fix the CardThreshold boundary at CardThrCtl register
  mmc: dw_mmc: NULL dereference in error message
  mmc: pwrseq: Use highest priority for eMMC restart handler
  mmc: mediatek: add HS400 support
  mmc: mmc: extend the mmc_send_tuning()
  mmc: mediatek: add implement of ops->hw_reset()
  mmc: mediatek: fix got GPD checksum error interrupt when data transfer
  mmc: mediatek: change the argument "ddr" to "timing"
  mmc: mediatek: make cmd_ints_mask to const
  mmc: dt-bindings: update Mediatek MMC bindings
  mmc: core: Add DT bindings for eMMC hardware reset support
  mmc: omap_hsmmc: Enable omap_hsmmc for Keystone 2
  mmc: sdhci-acpi: Add more ACPI HIDs for Intel controllers
  mmc: sdhci-pci: Add more PCI IDs for Intel controllers
  arm: lpc18xx_defconfig: remove CONFIG_MMC_DW_IDMAC
  arm: hisi_defconfig: remove CONFIG_MMC_DW_IDMAC
  arm: exynos_defconfig: remove CONFIG_MMC_DW_IDMAC
  arc: axs10x_defconfig: remove CONFIG_MMC_DW_IDMAC
  mips: pistachio_defconfig: remove CONFIG_MMC_DW_IDMAC
  ...

Merge tag 'hwmon-for-linus-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "New driver for MAX31790, added support for TMP75C, as well as cleanups
  and minor improvements in various drivers"

* tag 'hwmon-for-linus-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (fam15h_power) Add max compute unit accumulated power
  hwmon: (fam15h_power) Enable power1_input on AMD Carrizo
  hwmon: (fam15h_power) Refactor attributes for dynamically added
  hwmon: (ina2xx) remove no longer used variable 'kind'
  hwmon: (nct6775) Introduce separate temperature labels for NCT6792 and NCT6793
  hwmon: (nct6775) NCT6791D and NCT6792D have an additional temperature source
  hwmon: (ina2xx) give precedence to DT over checking for platform data.
  hwmon: (ina2xx) convert driver to using regmap
  hwmon: (coretemp) Increase limit of maximum core ID from 32 to 128.
  hwmon: (lm75) Add support for TMP75C
  hwmon: (ibmpowernv) Add OF compatibility table entry
  hwmon: (abx500) drop the use of IRQF_NO_SUSPEND
  hwmon: (max31790) Fix dereference of ERR_PTR
  hwmon: Driver for Maxim MAX31790

It turns out that at least some versions of glibc end up reading
/proc/meminfo at every single startup, because glibc wants to know the
amount of memory the machine has.  And while that's arguably insane,
it's just how things are.

And it turns out that it's not all that expensive most of the time, but
the vmalloc information statistics (amount of virtual memory used in the
vmalloc space, and the biggest remaining chunk) can be rather expensive
to compute.

The 'get_vmalloc_info()' function actually showed up on my profiles as
4% of the CPU usage of "make test" in the git source repository, because
the git tests are lots of very short-lived shell-scripts etc.

It turns out that apparently this same silly vmalloc info gathering
shows up on the facebook servers too, according to Dave Jones.  So it's
not just "make test" for git.

We had two patches to just cache the information (one by me, one by
Ingo) to mitigate this issue, but the whole vmalloc information of of
rather dubious value to begin with, and people who *actually* want to
know what the situation is wrt the vmalloc area should just look at the
much more complete /proc/vmallocinfo instead.

In fact, according to my testing - and perhaps more importantly,
according to that big search engine in the sky: Google - there is
nothing out there that actually cares about those two expensive fields:
VmallocUsed and VmallocChunk.

So let's try to just remove them entirely.  Actually, this just removes
the computation and reports the numbers as zero for now, just to try to
be minimally intrusive.

If this breaks anything, we'll obviously have to re-introduce the code
to compute this all and add the caching patches on top.  But if given
the option, I'd really prefer to just remove this bad idea entirely
rather than add even more code to work around our historical mistake
that likely nobody really cares about.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge file descriptor allocation speedup.

Eric Dumazet has a test-case for a fairly common network deamon load
pattern: openign and closing a lot of sockets that each have very little
work done on them.  It turns out that in that case, the cost of just
finding the correct file descriptor number can be a dominating factor.

We've long had a trivial optimization for allocating file descriptors
sequentially, but that optimization ends up being not very effective
when other file descriptors are being closed concurrently, and the fd
patterns are not some simple FIFO pattern.  In such cases we ended up
spending a lot of time just scanning the bitmap of open file descriptors
in order to find the next file descriptor number to open.

This trivial patch-series mitigates that by simply introducing a
second-level bitmap of which words in the first bitmap are already fully
allocated.  That cuts down the cost of scanning by an order of magnitude
in some pathological (but realistic) cases.

The second patch is an even more trivial patch to avoid unnecessarily
dirtying the cacheline for the close-on-exec bit array that normally
ends up being all empty.

* fs-file-descriptor-optimization:
  vfs: conditionally clear close-on-exec flag
  vfs: Fix pathological performance case for __alloc_fd()

Pull memremap fix from Dan Williams:
 "The new memremap() api introduced in the 4.3 cycle to unify/replace
  ioremap_cache() and ioremap_wt() is mishandling the highmem case.
  This patch has received a build success notification from a
  0day-kbuild-robot run and has received an ack from Ard"

From the commit message:
 "The impact of this bug is low for now since the pmem driver is the
  only user of memremap(), but this is important to fix before more
  conversions to memremap arrive in 4.4"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  memremap: fix highmem support

Pull x86 fixes from Thomas Gleixner:
 "This set of updates contains:

   - Another bugfix for the pathologic vm86 machinery.  Clear
     thread.vm86 on fork to prevent corrupting the parent state.  This
     comes along with an update to the vm86 selftest case

   - Fix another corner case in the ioapic setup code which causes a
     boot crash on some oddball systems

   - Fix the fallout from the dma allocation consolidation work, which
     leads to a NULL pointer dereference when the allocation code is
     called with a NULL device"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/vm86: Set thread.vm86 to NULL on fork/clone
  selftests/x86: Add a fork() to entry_from_vm86 to catch fork bugs
  x86/ioapic: Prevent NULL pointer dereference in setup_ioapic_dest()
  x86/dma-mapping: Fix arch_dma_alloc_attrs() oops with NULL dev

Pull timer fixes from Thomas Gleixner:
 "The last round of minimalistic fixes for clocksource drivers:

   - Prevent multiple shutdown of the sh_mtu2 clocksource

   - Annotate a bunch of clocksource/schedclock functions with notrace
     to prevent an annoying ftrace recursion issue"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/sh_mtu2: Fix multiple shutdown call issue
  clocksource/drivers/digicolor: Prevent ftrace recursion
  clocksource/drivers/fsl_ftm_timer: Prevent ftrace recursion
  clocksource/drivers/vf_pit_timer: Prevent ftrace recursion
  clocksource/drivers/prima2: Prevent ftrace recursion
  clocksource/drivers/samsung_pwm_timer: Prevent ftrace recursion
  clocksource/drivers/pistachio: Prevent ftrace recursion
  clocksource/drivers/arm_global_timer: Prevent ftrace recursion

Pull irq fixes from Thomas Gleixner:
 "The last two one-liners for 4.3 from the irqchip space:

   - Regression fix for armada SoC which addresses the fallout from the
     set_irq_flags() cleanup

   - Add the missing propagation of the irq_set_type() callback to the
     parent interrupt controller of the tegra interrupt chip"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/tegra: Propagate IRQ type setting to parent
  irqchip/armada-370-xp: Fix regression by clearing IRQ_NOAUTOEN

- Relax dependencies on SPI_MASTER for drivers in the SPI menu
  that already has this dependency.
- Move out the expander that would be hidden for I2C access if
  SPI_MASTER was not selected. Tentatively create a separate
  menu for this.
- Move the ZX SoC driver to memory-mapped drivers, this must be
  a mistake and only worked because the system has an SPI master
  enabled at the same time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The I2C expander menu already depends on I2C, drop subdependecies
on individual drivers. Keep the instances of depends on I2C=y
though, so these are still restricted to the compiled-in case.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Port-mapped I/O depends on X86 already, so individual drivers need
not specify this dependency.
Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull ARM SoC fixes from Olof Johansson:
 "This should be our final batch of fixes for 4.3:

   - A patch from Sudeep Holla that fixes annotation of wakeup sources
     properly, old unused format seems to have spread through copying.

   - Two patches from Tony for OMAP.  One dealing with MUSB setup
     problems due to runtime PM being enabled too early on the parent
     device.  The other fixes IRQ numbering for OMAP1"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  usb: musb: omap2430: Fix regression caused by driver core change
  ARM: OMAP1: fix incorrect INT_DMA_LCD
  ARM: dts: fix gpio-keys wakeup-source property

Pull SCSI fixes from James Bottomley:
 "This is three essential bug fixes for various SCSI parts.

  The only affected users are SCSI multi-path via device handler
  (basically all the enterprise) and mvsas users.  The dh bugs are an
  async entanglement in boot resulting in a serious WARN_ON trip and a
  use after free on remove leading to a crash with strict memory
  accounting.  The mvsas bug manifests as a null deref oops but only on
  abort sequences; however, these can commonly occur with SATA attached
  devices, hence the fix"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi_dh: don't try to load a device handler during async probing
  scsi_dh: fix use-after-free when removing scsi device
  mvsas: Fix NULL pointer dereference in mvs_slot_task_free

Pull md bug fixes from Neil Brown:
 "Two more bug fixes for md.

  One bugfix for a list corruption in raid5 because of incorrect
  locking.

  Other for possible data corruption when a recovering device is failed,
  removed, and re-added.

  Both tagged for -stable"

* tag 'md/4.3-rc7-fixes' of git://neil.brown.name/md:
  Revert "md: allow a partially recovered device to be hot-added to an array."
  md/raid5: fix locking in handle_stripe_clean_event()

Pull drm fixes from Dave Airlie:
 "Two drm atomic core fixes.

  And two radeon patches needed to fix a backlight regression on some
  older hardware"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Correct arguments to list_tail_add in create blob ioctl
  drm: crtc: integer overflow in drm_property_create_blob()
  drm/radeon: fix dpms when driver backlight control is disabled
  drm/radeon: move bl encoder assignment into bl init

We clear the close-on-exec flag when opening and closing files, and the
bit was almost always already clear before.  Avoid dirtying the
cacheline if the clearning isn't necessary.  That avoids unnecessary
cacheline dirtying and bouncing in multi-socket environments.

Eric Dumazet has a file descriptor benchmark that goes 4% faster from
this on his two-socket machine.  It's probably partly superlinear
improvement due to getting slightly less spinlock contention on the
file_lock spinlock due to less work in the critical section.
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Al Viro points out that:
> >     * [Linux-specific aside] our __alloc_fd() can degrade quite badly
> > with some use patterns.  The cacheline pingpong in the bitmap is probably
> > inevitable, unless we accept considerably heavier memory footprint,
> > but we also have a case when alloc_fd() takes O(n) and it's _not_ hard
> > to trigger - close(3);open(...); will have the next open() after that
> > scanning the entire in-use bitmap.

And Eric Dumazet has a somewhat realistic multithreaded microbenchmark
that opens and closes a lot of sockets with minimal work per socket.

This patch largely fixes it.  We keep a 2nd-level bitmap of the open
file bitmaps, showing which words are already full.  So then we can
traverse that second-level bitmap to efficiently skip already allocated
file descriptors.

On his benchmark, this improves performance by up to an order of
magnitude, by avoiding the excessive open file bitmap scanning.
Tested-and-acked-by: Eric Dumazet <edumazet@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch adds a member in fam15h_power_data which specifies the
maximum accumulated power in a compute unit.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

This patch enables power1_input attribute for Carrizo platform.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Attributes depend on the CPU model the driver gets loaded on.
Therefore, add those attributes dynamically at init time. This is more
flexible to control the different attributes on different platforms.
Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Pull Ceph fix from Sage Weil:
 "This sets the stable pages flag on the RBD block device when we have
  CRCs enabled.  (This is necessary since the default assumption for
  block devices changed in 3.9)"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: require stable pages if message data CRCs are enabled

Pull overlayfs bug fixes from Miklos Szeredi:
 "This contains fixes for bugs that appeared in earlier kernels (all are
  marked for -stable)"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: free lower_mnt array in ovl_put_super
  ovl: free stack of paths in ovl_fill_super
  ovl: fix open in stacked overlay
  ovl: fix dentry reference leak
  ovl: use O_LARGEFILE in ovl_copy_up()

This removes a needless loop which was caught in pinconf.c.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Laurent Meunier <laurent.meunier@st.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER
to guard the drivers/pinctrl/uniphier directory.

The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long
(it would break the indentation in drivers/pinctrl/Makefile),
so rename it into CONFIG_PINCTRL_UNIPHIER.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix up Sören's name in the Zynq driver. I caused this. I fix it.
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There are a bunch of drivers that utilize the "ngpios" DT property
without any vendor prefix. Try to start cleaning up the mess by
defining what we mean by this property.

Cc: devicetree@vger.kernel.org
Cc: Pramod Kumar <pramodku@broadcom.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add an entry for the ATH79 GPIO driver with myself as maintainer.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In Microsoft Surface3 the GPIO detecting lid state is shared between GPIO
event and operation region. Below is simplied version of the DSDT from
Surface3 including relevant parts:

    Scope (GPO0)
    {
        Name (_AEI, ResourceTemplate ()
        {
            GpioInt (Edge, ActiveBoth, Shared, PullNone, 0x0000,
                "\\_SB.GPO0", 0x00, ResourceConsumer, ,
                )
                {   // Pin list
                    0x004C
                }
        })

        OperationRegion (GPOR, GeneralPurposeIo, Zero, One)
        Field (GPOR, ByteAcc, NoLock, Preserve)
        {
            Connection (
                GpioIo (Shared, PullNone, 0x0000, 0x0000,
                    IoRestrictionNone, "\\_SB.GPO0", 0x00,
                    ResourceConsumer,,)
                    {   // Pin list
                        0x004C
                    }
            ),
            HELD,   1
        }

        Method (_E4C, 0, Serialized)  // _Exx: Edge-Triggered GPE
        {
            If ((HELD == One))
            {
                ^^LID.LIDB = One
            }
            Else
            {
                ^^LID.LIDB = Zero
                Notify (LID, 0x80) // Status Change
            }

            Notify (^^PCI0.SPI1.NTRG, One) // Device Check
        }
    }

When GPIO 0x4c changes we call ASL method _E4C which tries to read HELD
field (the same GPIO). This triggers following error on the console:

    ACPI Error: Method parse/execution failed [\_SB.GPO0._E4C]
        (Node ffff88013f4b4438), AE_ERROR (20150930/psparse-542)

The error happens because ACPI GPIO operation region handler
(acpi_gpio_adr_space_handler()) tries to acquire the very same GPIO which
returns an error (-EBUSY) because the GPIO is already reserved for the GPIO
event.

Fix this so that we "borrow" the event GPIO if we find the GPIO belongs to
an event. Allow this only for GPIOs that are read.

To be able to go through acpi_gpio->events list for operation region access
we need to make sure the list is properly initialized whenever GPIO chip is
registered.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=106571Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Create a Kconfig submenu for drivers using X86 port-mapped I/O
and depend on X86 for this.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Andreas Bofjall <andreas@gazonk.org>
Cc: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Bruno Randolf <br1@einfach.org>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull networking fixes from David Miller:

 1) Fix two regressions in ipv6 route lookups, particularly wrt output
    interface specifications in the lookup key.  From David Ahern.

 2) Fix checks in ipv6 IPSEC tunnel pre-encap fragmentation, from
    Herbert Xu.

 3) Fix mis-advertisement of 1000BASE-T on bcm63xx_enet, from Simon
    Arlott.

 4) Some smsc phys misbehave with energy detect mode enabled, so add a
    DT property and disable it on such switches.  From Heiko Schocher.

 5) Fix TSO corruption on TX in mv643xx_eth, from Philipp Kirchhofer.

 6) Fix regression added by removal of openvswitch vport stats, from
    James Morse.

 7) Vendor Kconfig options should be bool, not tristate, from Andreas
    Schwab.

 8) Use non-_BH() net stats bump in tcp_xmit_probe_skb(), otherwise we
    barf during TCP REPAIR operations.

 9) Fix various bugs in openvswitch conntrack support, from Joe
    Stringer.

10) Fix NETLINK_LIST_MEMBERSHIPS locking, from David Herrmann.

11) Don't have VSOCK do sock_put() in interrupt context, from Jorgen
    Hansen.

12) Fix skb_realloc_headroom() failures properly in ISDN, from Karsten
    Keil.

13) Add some device IDs to qmi_wwan, from Bjorn Mork.

14) Fix ovs egress tunnel information when using lwtunnel devices, from
    Pravin B Shelar.

15) Add missing NETIF_F_FRAGLIST to macvtab feature list, from Jason
    Wang.

16) Fix incorrect handling of throw routes when the result of the throw
    cannot find a match, from Xin Long.

17) Protect ipv6 MTU calculations from wrap-around, from Hannes Frederic
    Sowa.

18) Fix failed autonegotiation on KSZ9031 micrel PHYs, from Nathan
    Sullivan.

19) Add missing memory barries in descriptor accesses or xgbe driver,
    from Thomas Lendacky.

20) Fix release conditon test in pppoe_release(), from Guillaume Nault.

21) Fix gianfar bugs wrt filter configuration, from Claudiu Manoil.

22) Fix violations of RX buffer alignment in sh_eth driver, from Sergei
    Shtylyov.

23) Fixing missing of_node_put() calls in various places around the
    networking, from Julia Lawall.

24) Fix incorrect leaf now walking in ipv4 routing tree, from Alexander
    Duyck.

25) RDS doesn't check pskb_pull()/pskb_trim() return values, from
    Sowmini Varadhan.

26) Fix VLAN configuration in mlx4 driver, from Jack Morgenstein.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (79 commits)
  ipv6: protect mtu calculation of wrap-around and infinite loop by rounding issues
  Revert "Merge branch 'ipv6-overflow-arith'"
  net/mlx4: Copy/set only sizeof struct mlx4_eqe bytes
  net/mlx4_en: Explicitly set no vlan tags in WQE ctrl segment when no vlan is present
  vhost: fix performance on LE hosts
  bpf: sample: define aarch64 specific registers
  amd-xgbe: Fix race between access of desc and desc index
  RDS-TCP: Recover correctly from pskb_pull()/pksb_trim() failure in rds_tcp_data_recv
  forcedeth: fix unilateral interrupt disabling in netpoll path
  openvswitch: Fix skb leak using IPv6 defrag
  ipv6: Export nf_ct_frag6_consume_orig()
  openvswitch: Fix double-free on ip_defrag() errors
  fib_trie: leaf_walk_rcu should not compute key if key is less than pn->key
  net: mv643xx_eth: add missing of_node_put
  ath6kl: add missing of_node_put
  net: phy: mdio: add missing of_node_put
  netdev/phy: add missing of_node_put
  net: netcp: add missing of_node_put
  net: thunderx: add missing of_node_put
  ipv6: gre: support SIT encapsulation
  ...

Signed-off-by: Marc Titinger <mtitinger@baylibre.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

thread.vm86 points to per-task information -- the pointer should not
be copied on clone.

Fixes: d4ce0f26 ("x86/vm86: Move fields from 'struct kernel_vm86_struct' to 'struct vm86'")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Stas Sergeev <stsp@list.ru>
Link: http://lkml.kernel.org/r/71c5d6985d70ec8197c8d72f003823c81b7dcf99.1446270067.git.luto@kernel.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Mere possession of vm86 state is strange.  Make sure that nothing
gets corrupted if we fork after calling vm86().
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Stas Sergeev <stsp@list.ru>
Link: http://lkml.kernel.org/r/08f83295460a80e41dc5e3e81ec40d6844d316f5.1446270067.git.luto@kernel.orgSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull input layer fixes from Dmitry Torokhov:

 - a change to the ALPS driver where we had limit the quirk for
   trackstick handling from being active on all Dells to just a few
   models

 - a fix for a build dependency issue in the sur40 driver

 - a small clock handling fixup in the LPC32xx touchscreen driver

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: alps - only the Dell Latitude D420/430/620/630 have separate stick button bits
  Input: sur40 - add dependency on VIDEO_V4L2
  Input: lpc32xx_ts - fix warnings caused by enabling unprepared clock

Pull PCI fix from Bjorn Helgaas:
 "Sorry for this last-minute update; it's been in -next for quite a
  while, but I forgot about it until I started getting ready for the
  merge window.

  It's small and fixes a way a user could cause a panic via sysfs, so I
  think it's worth getting it in v4.3.

  NUMA:
    - Prevent out of bounds access in sysfs numa_node override (Sasha Levin)"

* tag 'pci-v4.3-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Prevent out of bounds access in numa_node override

Merge tag 'omap-for-v4.3/fixes-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Two omap regression fixes:

- Fix omap3 MUSB with DMA caused by driver core changes

- Fix LCD DMA interrupt number for omap1 that did not
  get changed for sparse IRQ changes

* tag 'omap-for-v4.3/fixes-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  usb: musb: omap2430: Fix regression caused by driver core change
  ARM: OMAP1: fix incorrect INT_DMA_LCD
Signed-off-by: Olof Johansson <olof@lixom.net>