In order for e1000e to support MDI setting support via
ethtool this code is needed to allow setting the MDI state
via software.

This is in regards to the related ethtool patch and
fixes bugzilla.kernel.org bug 11998
Signed-off-by: Bruce W Allan <bruce.w.allan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change modifies the core ethtool struct to allow a driver to
support setting of MDI/MDI-X state for twisted pair wiring.  This
change uses a previously reserved u8 and should not change any
binary compatibility of ethtool.

Also as per Ben Hutchings' suggestion, the capabilities are
stored in a separate byte so the driver can report if it supports
changing settings.

see thread: http://kerneltrap.org/mailarchive/linux-netdev/2010/11/17/6289820/thread

see ethtool patches titled:
ethtool: allow setting MDI-X state
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: Aaron Brown aaron.f.brown@intel.com
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This is resolved by two things:
1) allow dev_addr of different length than ETH_ALEN
2) during port add, check for dev->type and change it if necessary
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Peter P Waskiewicz Jr says:

====================
This series contains multiple updates to the ixgbe driver.

The following are changes since commit 02644a17:
    sctp: fix bogus if statement in sctp_auth_recv_cid()

and are available in the git repository at:
  git://git.kernel.org/pub/scm/linux/kernel/git/ppwaskie/net-next master

Alexander Duyck (9):
  ixgbe: Remove code that was initializing Rx page offset
  ixgbe: combine ixgbe_add_rx_frag and ixgbe_can_reuse_page
  ixgbe: Only use double buffering if page size is less than 8K
  ixgbe: Have the CPU take ownership of the buffers sooner
  ixgbe: Make pull tail function separate from rest of cleanup_headers
  ixgbe: Copybreak sooner to avoid get_page/put_page and offset change
    overhead
  ixgbe: Make allocating skb and placing data in it a separate function
  ixgbe: Roll RSC code into non-EOP code
  ixgbe: Rewrite code related to configuring IFCS bit in Tx descriptor
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Gets rid of the need for users to specify the maximum number of
name publications supported by TIPC. TIPC now automatically provides
support for the maximum number of name publications to 65535.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Gets rid of the need for users to specify the maximum number of
name subscriptions supported by TIPC. TIPC now automatically provides
support for the maximum number of name subscriptions to 65535.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added to the following:

 - tipc_random
 - tipc_own_addr
 - tipc_max_ports
 - tipc_net_id
 - tipc_remote_management
 - handler_enabled

The above global variables are read often, but written rarely. Use
__read_mostly to prevent them being on the same cacheline as another
variable which is written to often, which would cause cacheline
bouncing.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is nothing changing this variable dynamically, so change
it to a macro to make that more obvious when reading the code.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since now tipc_net_start() always returns a success code - 0, its
return value type should be changed from integer to void, which can
avoid unnecessary check for its return value.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After eliminating the mechanism which checks whether all letters
in media name string are within a given character set, the
media_name_valid routine becomes trivial.  It is also only
used once, so it is unnecessary to keep it as a separate function.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no real reason to check whether all letters in the given
media name and network interface name are within the character set
defined in tipc_alphabet array. Even if we eliminate the checking,
the rest of checking conditions in tipc_enable_bearer() can ensure
we do not enable an invalid or illegal bearer.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the lockdep validator is enabled, it will report the below
warning when we enable a TIPC bearer:

[ INFO: possible irq lock inversion dependency detected ]
---------------------------------------------------------
Possible interrupt unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(ptype_lock);
                                local_irq_disable();
                                lock(tipc_net_lock);
                                lock(ptype_lock);
   <Interrupt>
   lock(tipc_net_lock);

  *** DEADLOCK ***

the shortest dependencies between 2nd lock and 1st lock:
  -> (ptype_lock){+.+...} ops: 10 {
[...]
SOFTIRQ-ON-W at:
                      [<c1089418>] __lock_acquire+0x528/0x13e0
                      [<c108a360>] lock_acquire+0x90/0x100
                      [<c1553c38>] _raw_spin_lock+0x38/0x50
                      [<c14651ca>] dev_add_pack+0x3a/0x60
                      [<c182da75>] arp_init+0x1a/0x48
                      [<c182dce5>] inet_init+0x181/0x27e
                      [<c1001114>] do_one_initcall+0x34/0x170
                      [<c17f7329>] kernel_init+0x110/0x1b2
                      [<c155b6a2>] kernel_thread_helper+0x6/0x10
[...]
   ... key      at: [<c17e4b10>] ptype_lock+0x10/0x20
   ... acquired at:
    [<c108a360>] lock_acquire+0x90/0x100
    [<c1553c38>] _raw_spin_lock+0x38/0x50
    [<c14651ca>] dev_add_pack+0x3a/0x60
    [<c8bc18d2>] enable_bearer+0xf2/0x140 [tipc]
    [<c8bb283a>] tipc_enable_bearer+0x1ba/0x450 [tipc]
    [<c8bb3a04>] tipc_cfg_do_cmd+0x5c4/0x830 [tipc]
    [<c8bbc032>] handle_cmd+0x42/0xd0 [tipc]
    [<c148e802>] genl_rcv_msg+0x232/0x280
    [<c148d3f6>] netlink_rcv_skb+0x86/0xb0
    [<c148e5bc>] genl_rcv+0x1c/0x30
    [<c148d144>] netlink_unicast+0x174/0x1f0
    [<c148ddab>] netlink_sendmsg+0x1eb/0x2d0
    [<c1456bc1>] sock_aio_write+0x161/0x170
    [<c1135a7c>] do_sync_write+0xac/0xf0
    [<c11360f6>] vfs_write+0x156/0x170
    [<c11361e2>] sys_write+0x42/0x70
    [<c155b0df>] sysenter_do_call+0x12/0x38
[...]
}
  -> (tipc_net_lock){+..-..} ops: 4 {
[...]
    IN-SOFTIRQ-R at:
                     [<c108953a>] __lock_acquire+0x64a/0x13e0
                     [<c108a360>] lock_acquire+0x90/0x100
                     [<c15541cd>] _raw_read_lock_bh+0x3d/0x50
                     [<c8bb874d>] tipc_recv_msg+0x1d/0x830 [tipc]
                     [<c8bc195f>] recv_msg+0x3f/0x50 [tipc]
                     [<c146a5fa>] __netif_receive_skb+0x22a/0x590
                     [<c146ab0b>] netif_receive_skb+0x2b/0xf0
                     [<c13c43d2>] pcnet32_poll+0x292/0x780
                     [<c146b00a>] net_rx_action+0xfa/0x1e0
                     [<c103a4be>] __do_softirq+0xae/0x1e0
[...]
}

>From the log, we can see three different call chains between
CPU0 and CPU1:

Time 0 on CPU0:

  kernel_init()->inet_init()->dev_add_pack()

At time 0, the ptype_lock is held by CPU0 in dev_add_pack();

Time 1 on CPU1:

  tipc_enable_bearer()->enable_bearer()->dev_add_pack()

At time 1, tipc_enable_bearer() first holds tipc_net_lock, and then
wants to take ptype_lock to register TIPC protocol handler into the
networking stack.  But the ptype_lock has been taken by dev_add_pack()
on CPU0, so at this time the dev_add_pack() running on CPU1 has to be
busy looping.

Time 2 on CPU0:

  netif_receive_skb()->recv_msg()->tipc_recv_msg()

At time 2, an incoming TIPC packet arrives at CPU0, hence
tipc_recv_msg() will be invoked. In tipc_recv_msg(), it first wants
to hold tipc_net_lock.  At the moment, below scenario happens:

On CPU0, below is our sequence of taking locks:

  lock(ptype_lock)->lock(tipc_net_lock)

On CPU1, our sequence of taking locks looks like:

  lock(tipc_net_lock)->lock(ptype_lock)

Obviously deadlock may happen in this case.

But please note the deadlock possibly doesn't occur at all when the
first TIPC bearer is enabled.  Before enable_bearer() -- running on
CPU1 does not hold ptype_lock, so the TIPC receive handler (i.e.
recv_msg()) is not registered successfully via dev_add_pack(), so
the tipc_recv_msg() cannot be called by recv_msg() even if a TIPC
message comes to CPU0. But when the second TIPC bearer is
registered, the deadlock can perhaps really happen.

To fix it, we will push the work of registering TIPC protocol
handler into workqueue context. After the change, both paths taking
ptype_lock are always in process contexts, thus, the deadlock should
never occur.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ethernet media initialization is only done when TIPC is started or
switched to network mode. So the initialization of the network device
notifier structure can be moved out of this function and done
statically instead.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reported value is the same reported by the FANOUT getsockoption, but
unlike it, the absent fanout setup results in absent nlattr, rather
than in nlattr with zero value. This is done so, since zero fanout
report may mean both -- no fanout, and fanout with both id and type zero.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One extension bit may result in two nlattrs -- one per ring type.
If some ring type is not configured, then the respective nlatts
will be empty.

The structure reported contains the data, that is given to the
corresponding ring setup socket option.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a one byte hole between p->hop_limit and p->flowinfo where
stack memory is leaked to the user.  This was introduced in c12b395a
"gre: Support GRE over IPv6".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>

Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change updates the code related to configuring the transmit frame
checksum.  Specifically I have updated the code so that we can only skip
inserting the checksum in the case that we are not performing some other
offload that will modify the frame data.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This change moves the RSC code into the non-EOP descriptor handling
function. The main motivation behind this change is to help reduce the
overhead in the non-RSC case. Previously the non-RSC path code would
always be checking for append count even if RSC had been disabled. Now
this code is completely skipped in a single conditional check instead of
having to make two separate checks.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This patch creates a function named ixgbe_fetch_rx_buffer. The sole
purpose of this function is to retrieve a single buffer off of the ring and
to place it in an skb.

The advantage to doing this is that it helps improve the readability since
I can decrease the indentation and for the code in this section.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This change makes it so that if only the first 256 bytes of a buffer are
used we just copy the data out and leave the offset and page count
unchanged. There are multiple advantages to this. First it allows us to
reuse the page much more in the case of pages larger than 4K. It also
allows us to avoid some expensive atomic operations in the form of
get_page/put_page. In perf I have seen CPU utilization for put_page drop
from 3.5% to 1.8% as a result of this patch when doing small packet routing,
and packet rates increased by about 3%.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This change creates a separate function for functionality similar to
pskb_pull_tail.  The main motivation for moving it to a separate function
is so that later I can just skip this function in the case where we have
already copied the buffer into skb->head.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This patch makes it so that we will always have ownership of the buffers by
the time we get to ixgbe_add_rx_frag. This is necessary as I am planning to
add a copy-break to ixgbe_add_rx_frag and in order for that to function
correctly we need the CPU to have ownership of the buffer.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This change makes it so that we do not use double buffering if the page
size is larger than 4K.  Instead we will simply walk through the page using
up to 3K per receive, and if we receive less than we only move the offset
by that amount.  We will free the page when there is no longer any space
left that we can use instead of checking the page count to see if we can
cycle back to the start.

The main motivation behind this is to avoid the unnecessary truesize cost
for using a half page when most packets are 2K or smaller. With this new
approach the largest possible truesize for a page fragment will be 3K when
PAGE_SIZE is larger than 4K.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This patch combines ixgbe_add_rx_frag and ixgbe_can_reuse_page into a
single function. The main motivation behind this is to make better use of
the values so that we don't have to load them from memory and into
registers twice.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

This change reverts an earlier patch that introduced
ixgbe_init_rx_page_offset. The idea behind the function was to provide
some variation in the starting offset for the page in order to reduce
hot-spots in the cache. However it doesn't appear to provide any
significant benefit in the testing I have done. It has however been a
source of several bugs, and it blocks us from being able to use 2K
fragments on larger page sizes. So the decision I made was to remove it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>

There is an extra semi-colon here, so we always return 0 instead of
calling __sctp_auth_cid().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct seq_net_private has no struct net
if CONFIG_NET_NS is not enabled
Signed-off-by: Ulrich Weber <ulrich.weber@sophos.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
This is a batch of updates intended for 3.7.  The ath9k, mwifiex,
and b43 drivers get the bulk of the commits this time, with a handful
of other driver bits thrown-in.  It is mostly just minor fixes and
cleanups, etc.

Also included is a Bluetooth pull, with a lot of refactoring.
Gustavo says:

	"These are the changes I queued for 3.7. There are a many
	small fixes/improvements by Andre Guedes. A l2cap channel
	refcounting refactor by Jaganath. Bluetooth sockets now
	appears in /proc/net, by Masatake Yamato and Sachin Kamat
	changes ours drivers to use devm_kzalloc()."
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The field tp->snd_wl1 is twice initialized, the second time
seems to be wrong as it may overwrite any update in tcp_ack.
Signed-off-by: Razvan Ghitulete <rghitulete@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sematically speaking, xfrm_mgr.acquire is called when kernel intends to ask
user space IKE daemon to negotiate SAs with peers. IOW the direction will
*always* be XFRM_POLICY_OUT, so remove int dir for clarity.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem

I got the following compile error:

In file included from include/net/sctp/checksum.h:46:0,
                 from net/ipv4/netfilter/nf_nat_proto_sctp.c:14:
include/net/sctp/sctp.h: In function ‘sctp_dbg_objcnt_init’:
include/net/sctp/sctp.h:370:88: error: parameter name omitted
include/net/sctp/sctp.h: In function ‘sctp_dbg_objcnt_exit’:
include/net/sctp/sctp.h:371:88: error: parameter name omitted

which is caused by

	commit 13d782f6
	Author: Eric W. Biederman <ebiederm@xmission.com>
	Date:   Mon Aug 6 08:45:15 2012 +0000

	    sctp: Make the proc files per network namespace.

This patch could fix it.

Cc: David S. Miller <davem@davemloft.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add struct net as a parameter to sctp_verify_param so it can be passed
to sctp_verify_ext_param where struct net will be needed when the sctp
tunables become per net tunables.

Add struct net as a parameter to sctp_verify_init so struct net can be
passed to sctp_verify_param.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are a handle of state machine functions primarily those dealing
with processing INIT packets where there is neither a valid endpoint nor
a valid assoication from which to derive a struct net.  Therefore add
struct net * to the parameter list of sctp_state_fn_t and update all of
the state machine functions.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct net will be needed shortly when the tunables are made per network
namespace.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This trickles up through sctp_sm_lookup_event up to sctp_do_sm
and up further into sctp_primitiv_NAME before the code reaches
places where struct net can be reliably found.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Start with an empty sctp_net_table that will be populated as the various
tunable sysctls are made per net.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>