- 24 Jul, 2008 40 commits
-
-
Maciej W. Rozycki authored
Changes to the generic console support code that happened a while ago introduced a scenario where the initial console is used in parallel with the final console during a brief period when switching between the two is in progress. During that time a message about the switch-over is printed. With some combinations of chips, firmware and drivers, such as the DEC DZ11 clone used with the DECstation, a hang may happen because the firmware used for the initial console may not expect the state of the chip after it has been initialised by the driver. This is a workaround for the DZ11 which reuses the power-management callback to keep the transmitter of the line associated with the console enabled. It reflects the consensus reached in a discussion a while ago. Signed-off-by:
Maciej W. Rozycki <macro@linux-mips.org> Cc: Jiri Slaby <jirislaby@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Maciej W. Rozycki authored
Changes to the generic console support code that happened a while ago introduced a scenario where the initial console is used in parallel with the final console during a brief period when switching between the two is in progress. During that time a message about the switch-over is printed. With some combinations of chips, firmware and drivers, such as the Zilog Z85C30 SCC used with the DECstation, a hang may happen because the firmware used for the initial console may not expect the state of the chip after it has been initialised by the driver. This is not a bug in the firmware, as some registers it would have to examine are write-only. This is a workaround for the Z85C30 which reuses the power-management callback to keep the transmitter of the line associated with the console enabled. It reflects the consensus reached in a discussion a while ago. Signed-off-by:
-
Catalin(ux) M BOIE authored
It is a no-name PCI card. I found no reference to a producer so I used "UNKNOWN_0x1584" as the name. Full lspci: 01:07.0 0780: 10b5:9050 (rev 01) Subsystem: 10b5:1584 Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- \ ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- \ DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Interrupt: pin A routed to IRQ 10 Region 1: I/O ports at ec00 [size=128] Region 2: I/O ports at e480 [size=32] Region 3: I/O ports at e400 [size=8] Capabilities: [40] Power Management version 1 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA \ PME(D0+,D1-,D2-,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] #06 [0080] Capabilities: [4c] Vital Product Data After: 0000:01:07.0: ttyS4 at I/O 0xe480 (irq = 10) is a 16550A 0000:01:07.0: ttyS5 at I/O 0xe488 (irq = 10) is a 16550A 0000:01:07.0: ttyS6 at I/O 0xe490 (irq = 10) is a 16550A 0000:01:07.0: ttyS7 at I/O 0xe498 (irq = 10) is a 16550A Signed-off-by:Catalin(ux) M BOIE <catab@embedromix.ro> Acked-by:
Alan Cox <alan@redhat.com> Acked-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Aristeu Rozanski authored
Intel 82571 has a "Serial Over LAN" feature that doesn't properly implements the receiving of break characters. When a break is received, it doesn't set UART_LSR_DR and unless another character is received, the break won't be received by the application. Signed-off-by:
Aristeu Rozanski <arozansk@redhat.com> Acked-by:
Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by:
-
Adrian Bunk authored
This patch adds the missing MODULE_LICENSE("GPL"). Signed-off-by:Adrian Bunk <bunk@kernel.org> Acked-by:
-
Ulrich Drepper authored
Remove the size parameter from the new epoll_create syscall and renames the syscall itself. The updated test program follows. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <time.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_epoll_create2 # ifdef __x86_64__ # define __NR_epoll_create2 291 # elif defined __i386__ # define __NR_epoll_create2 329 # else # error "need __NR_epoll_create2" # endif #endif #define EPOLL_CLOEXEC O_CLOEXEC int main (void) { int fd = syscall (__NR_epoll_create2, 0); if (fd == -1) { puts ("epoll_create2(0) failed"); return 1; } int coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if (coe & FD_CLOEXEC) { puts ("epoll_create2(0) set close-on-exec flag"); return 1; } close (fd); fd = syscall (__NR_epoll_create2, EPOLL_CLOEXEC); if (fd == -1) { puts ("epoll_create2(EPOLL_CLOEXEC) failed"); return 1; } coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if ((coe & FD_CLOEXEC) == 0) { puts ("epoll_create2(EPOLL_CLOEXEC) set close-on-exec flag"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by:Ulrich Drepper <drepper@redhat.com> Acked-by:
Davide Libenzi <davidel@xmailserver.org> Cc: Michael Kerrisk <mtk.manpages@googlemail.com> Cc: <linux-arch@vger.kernel.org> Signed-off-by:
-
Ulrich Drepper authored
This patch adds test that ensure the boundary conditions for the various constants introduced in the previous patches is met. No code is generated. [akpm@linux-foundation.org: fix alpha] Signed-off-by:
-
Ulrich Drepper authored
This patch adds non-blocking support for inotify_init1. The additional changes needed are minimal. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_inotify_init1 # ifdef __x86_64__ # define __NR_inotify_init1 294 # elif defined __i386__ # define __NR_inotify_init1 332 # else # error "need __NR_inotify_init1" # endif #endif #define IN_NONBLOCK O_NONBLOCK int main (void) { int fd = syscall (__NR_inotify_init1, 0); if (fd == -1) { puts ("inotify_init1(0) failed"); return 1; } int fl = fcntl (fd, F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if (fl & O_NONBLOCK) { puts ("inotify_init1(0) set non-blocking mode"); return 1; } close (fd); fd = syscall (__NR_inotify_init1, IN_NONBLOCK); if (fd == -1) { puts ("inotify_init1(IN_NONBLOCK) failed"); return 1; } fl = fcntl (fd, F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if ((fl & O_NONBLOCK) == 0) { puts ("inotify_init1(IN_NONBLOCK) set non-blocking mode"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Ulrich Drepper authored
This patch adds O_NONBLOCK support to pipe2. It is minimally more involved than the patches for eventfd et.al but still trivial. The interfaces of the create_write_pipe and create_read_pipe helper functions were changed and the one other caller as well. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_pipe2 # ifdef __x86_64__ # define __NR_pipe2 293 # elif defined __i386__ # define __NR_pipe2 331 # else # error "need __NR_pipe2" # endif #endif int main (void) { int fds[2]; if (syscall (__NR_pipe2, fds, 0) == -1) { puts ("pipe2(0) failed"); return 1; } for (int i = 0; i < 2; ++i) { int fl = fcntl (fds[i], F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if (fl & O_NONBLOCK) { printf ("pipe2(0) set non-blocking mode for fds[%d]\n", i); return 1; } close (fds[i]); } if (syscall (__NR_pipe2, fds, O_NONBLOCK) == -1) { puts ("pipe2(O_NONBLOCK) failed"); return 1; } for (int i = 0; i < 2; ++i) { int fl = fcntl (fds[i], F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if ((fl & O_NONBLOCK) == 0) { printf ("pipe2(O_NONBLOCK) does not set non-blocking mode for fds[%d]\n", i); return 1; } close (fds[i]); } puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Ulrich Drepper authored
This patch adds support for the TFD_NONBLOCK flag to timerfd_create. The additional changes needed are minimal. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <time.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_timerfd_create # ifdef __x86_64__ # define __NR_timerfd_create 283 # elif defined __i386__ # define __NR_timerfd_create 322 # else # error "need __NR_timerfd_create" # endif #endif #define TFD_NONBLOCK O_NONBLOCK int main (void) { int fd = syscall (__NR_timerfd_create, CLOCK_REALTIME, 0); if (fd == -1) { puts ("timerfd_create(0) failed"); return 1; } int fl = fcntl (fd, F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if (fl & O_NONBLOCK) { puts ("timerfd_create(0) set non-blocking mode"); return 1; } close (fd); fd = syscall (__NR_timerfd_create, CLOCK_REALTIME, TFD_NONBLOCK); if (fd == -1) { puts ("timerfd_create(TFD_NONBLOCK) failed"); return 1; } fl = fcntl (fd, F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if ((fl & O_NONBLOCK) == 0) { puts ("timerfd_create(TFD_NONBLOCK) set non-blocking mode"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Ulrich Drepper authored
This patch adds support for the EFD_NONBLOCK flag to eventfd2. The additional changes needed are minimal. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_eventfd2 # ifdef __x86_64__ # define __NR_eventfd2 290 # elif defined __i386__ # define __NR_eventfd2 328 # else # error "need __NR_eventfd2" # endif #endif #define EFD_NONBLOCK O_NONBLOCK int main (void) { int fd = syscall (__NR_eventfd2, 1, 0); if (fd == -1) { puts ("eventfd2(0) failed"); return 1; } int fl = fcntl (fd, F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if (fl & O_NONBLOCK) { puts ("eventfd2(0) sets non-blocking mode"); return 1; } close (fd); fd = syscall (__NR_eventfd2, 1, EFD_NONBLOCK); if (fd == -1) { puts ("eventfd2(EFD_NONBLOCK) failed"); return 1; } fl = fcntl (fd, F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if ((fl & O_NONBLOCK) == 0) { puts ("eventfd2(EFD_NONBLOCK) does not set non-blocking mode"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Ulrich Drepper authored
This patch adds support for the SFD_NONBLOCK flag to signalfd4. The additional changes needed are minimal. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <signal.h> #include <stdio.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_signalfd4 # ifdef __x86_64__ # define __NR_signalfd4 289 # elif defined __i386__ # define __NR_signalfd4 327 # else # error "need __NR_signalfd4" # endif #endif #define SFD_NONBLOCK O_NONBLOCK int main (void) { sigset_t ss; sigemptyset (&ss); sigaddset (&ss, SIGUSR1); int fd = syscall (__NR_signalfd4, -1, &ss, 8, 0); if (fd == -1) { puts ("signalfd4(0) failed"); return 1; } int fl = fcntl (fd, F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if (fl & O_NONBLOCK) { puts ("signalfd4(0) set non-blocking mode"); return 1; } close (fd); fd = syscall (__NR_signalfd4, -1, &ss, 8, SFD_NONBLOCK); if (fd == -1) { puts ("signalfd4(SFD_NONBLOCK) failed"); return 1; } fl = fcntl (fd, F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if ((fl & O_NONBLOCK) == 0) { puts ("signalfd4(SFD_NONBLOCK) does not set non-blocking mode"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Ulrich Drepper authored
This patch introduces support for the SOCK_NONBLOCK flag in socket, socketpair, and paccept. To do this the internal function sock_attach_fd gets an additional parameter which it uses to set the appropriate flag for the file descriptor. Given that in modern, scalable programs almost all socket connections are non-blocking and the minimal additional cost for the new functionality I see no reason not to add this code. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <pthread.h> #include <stdio.h> #include <unistd.h> #include <netinet/in.h> #include <sys/socket.h> #include <sys/syscall.h> #ifndef __NR_paccept # ifdef __x86_64__ # define __NR_paccept 288 # elif defined __i386__ # define SYS_PACCEPT 18 # define USE_SOCKETCALL 1 # else # error "need __NR_paccept" # endif #endif #ifdef USE_SOCKETCALL # define paccept(fd, addr, addrlen, mask, flags) \ ({ long args[6] = { \ (long) fd, (long) addr, (long) addrlen, (long) mask, 8, (long) flags }; \ syscall (__NR_socketcall, SYS_PACCEPT, args); }) #else # define paccept(fd, addr, addrlen, mask, flags) \ syscall (__NR_paccept, fd, addr, addrlen, mask, 8, flags) #endif #define PORT 57392 #define SOCK_NONBLOCK O_NONBLOCK static pthread_barrier_t b; static void * tf (void *arg) { pthread_barrier_wait (&b); int s = socket (AF_INET, SOCK_STREAM, 0); struct sockaddr_in sin; sin.sin_family = AF_INET; sin.sin_addr.s_addr = htonl (INADDR_LOOPBACK); sin.sin_port = htons (PORT); connect (s, (const struct sockaddr *) &sin, sizeof (sin)); close (s); pthread_barrier_wait (&b); pthread_barrier_wait (&b); s = socket (AF_INET, SOCK_STREAM, 0); sin.sin_port = htons (PORT); connect (s, (const struct sockaddr *) &sin, sizeof (sin)); close (s); pthread_barrier_wait (&b); return NULL; } int main (void) { int fd; fd = socket (PF_INET, SOCK_STREAM, 0); if (fd == -1) { puts ("socket(0) failed"); return 1; } int fl = fcntl (fd, F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if (fl & O_NONBLOCK) { puts ("socket(0) set non-blocking mode"); return 1; } close (fd); fd = socket (PF_INET, SOCK_STREAM|SOCK_NONBLOCK, 0); if (fd == -1) { puts ("socket(SOCK_NONBLOCK) failed"); return 1; } fl = fcntl (fd, F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if ((fl & O_NONBLOCK) == 0) { puts ("socket(SOCK_NONBLOCK) does not set non-blocking mode"); return 1; } close (fd); int fds[2]; if (socketpair (PF_UNIX, SOCK_STREAM, 0, fds) == -1) { puts ("socketpair(0) failed"); return 1; } for (int i = 0; i < 2; ++i) { fl = fcntl (fds[i], F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if (fl & O_NONBLOCK) { printf ("socketpair(0) set non-blocking mode for fds[%d]\n", i); return 1; } close (fds[i]); } if (socketpair (PF_UNIX, SOCK_STREAM|SOCK_NONBLOCK, 0, fds) == -1) { puts ("socketpair(SOCK_NONBLOCK) failed"); return 1; } for (int i = 0; i < 2; ++i) { fl = fcntl (fds[i], F_GETFL); if (fl == -1) { puts ("fcntl failed"); return 1; } if ((fl & O_NONBLOCK) == 0) { printf ("socketpair(SOCK_NONBLOCK) does not set non-blocking mode for fds[%d]\n", i); return 1; } close (fds[i]); } pthread_barrier_init (&b, NULL, 2); struct sockaddr_in sin; pthread_t th; if (pthread_create (&th, NULL, tf, NULL) != 0) { puts ("pthread_create failed"); return 1; } int s = socket (AF_INET, SOCK_STREAM, 0); int reuse = 1; setsockopt (s, SOL_SOCKET, SO_REUSEADDR, &reuse, sizeof (reuse)); sin.sin_family = AF_INET; sin.sin_addr.s_addr = htonl (INADDR_LOOPBACK); sin.sin_port = htons (PORT); bind (s, (struct sockaddr *) &sin, sizeof (sin)); listen (s, SOMAXCONN); pthread_barrier_wait (&b); int s2 = paccept (s, NULL, 0, NULL, 0); if (s2 < 0) { puts ("paccept(0) failed"); return 1; } fl = fcntl (s2, F_GETFL); if (fl & O_NONBLOCK) { puts ("paccept(0) set non-blocking mode"); return 1; } close (s2); close (s); pthread_barrier_wait (&b); s = socket (AF_INET, SOCK_STREAM, 0); sin.sin_port = htons (PORT); setsockopt (s, SOL_SOCKET, SO_REUSEADDR, &reuse, sizeof (reuse)); bind (s, (struct sockaddr *) &sin, sizeof (sin)); listen (s, SOMAXCONN); pthread_barrier_wait (&b); s2 = paccept (s, NULL, 0, NULL, SOCK_NONBLOCK); if (s2 < 0) { puts ("paccept(SOCK_NONBLOCK) failed"); return 1; } fl = fcntl (s2, F_GETFL); if ((fl & O_NONBLOCK) == 0) { puts ("paccept(SOCK_NONBLOCK) does not set non-blocking mode"); return 1; } close (s2); close (s); pthread_barrier_wait (&b); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Ulrich Drepper authored
Building on the previous change to anon_inode_getfd, this patch introduces support for handling of O_NONBLOCK in addition to the already supported O_CLOEXEC. Following patches will take advantage of this support. As can be seen, the additional support for supporting this functionality is minimal. Signed-off-by:
-
Ulrich Drepper authored
This patch introduces the new syscall inotify_init1 (note: the 1 stands for the one parameter the syscall takes, as opposed to no parameter before). The values accepted for this parameter are function-specific and defined in the inotify.h header. Here the values must match the O_* flags, though. In this patch CLOEXEC support is introduced. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_inotify_init1 # ifdef __x86_64__ # define __NR_inotify_init1 294 # elif defined __i386__ # define __NR_inotify_init1 332 # else # error "need __NR_inotify_init1" # endif #endif #define IN_CLOEXEC O_CLOEXEC int main (void) { int fd; fd = syscall (__NR_inotify_init1, 0); if (fd == -1) { puts ("inotify_init1(0) failed"); return 1; } int coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if (coe & FD_CLOEXEC) { puts ("inotify_init1(0) set close-on-exit"); return 1; } close (fd); fd = syscall (__NR_inotify_init1, IN_CLOEXEC); if (fd == -1) { puts ("inotify_init1(IN_CLOEXEC) failed"); return 1; } coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if ((coe & FD_CLOEXEC) == 0) { puts ("inotify_init1(O_CLOEXEC) does not set close-on-exit"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [akpm@linux-foundation.org: add sys_ni stub] Signed-off-by: -
Ulrich Drepper authored
This patch introduces the new syscall pipe2 which is like pipe but it also takes an additional parameter which takes a flag value. This patch implements the handling of O_CLOEXEC for the flag. I did not add support for the new syscall for the architectures which have a special sys_pipe implementation. I think the maintainers of those archs have the chance to go with the unified implementation but that's up to them. The implementation introduces do_pipe_flags. I did that instead of changing all callers of do_pipe because some of the callers are written in assembler. I would probably screw up changing the assembly code. To avoid breaking code do_pipe is now a small wrapper around do_pipe_flags. Once all callers are changed over to do_pipe_flags the old do_pipe function can be removed. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_pipe2 # ifdef __x86_64__ # define __NR_pipe2 293 # elif defined __i386__ # define __NR_pipe2 331 # else # error "need __NR_pipe2" # endif #endif int main (void) { int fd[2]; if (syscall (__NR_pipe2, fd, 0) != 0) { puts ("pipe2(0) failed"); return 1; } for (int i = 0; i < 2; ++i) { int coe = fcntl (fd[i], F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if (coe & FD_CLOEXEC) { printf ("pipe2(0) set close-on-exit for fd[%d]\n", i); return 1; } } close (fd[0]); close (fd[1]); if (syscall (__NR_pipe2, fd, O_CLOEXEC) != 0) { puts ("pipe2(O_CLOEXEC) failed"); return 1; } for (int i = 0; i < 2; ++i) { int coe = fcntl (fd[i], F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if ((coe & FD_CLOEXEC) == 0) { printf ("pipe2(O_CLOEXEC) does not set close-on-exit for fd[%d]\n", i); return 1; } } close (fd[0]); close (fd[1]); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Ulrich Drepper authored
This patch adds the new dup3 syscall. It extends the old dup2 syscall by one parameter which is meant to hold a flag value. Support for the O_CLOEXEC flag is added in this patch. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <time.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_dup3 # ifdef __x86_64__ # define __NR_dup3 292 # elif defined __i386__ # define __NR_dup3 330 # else # error "need __NR_dup3" # endif #endif int main (void) { int fd = syscall (__NR_dup3, 1, 4, 0); if (fd == -1) { puts ("dup3(0) failed"); return 1; } int coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if (coe & FD_CLOEXEC) { puts ("dup3(0) set close-on-exec flag"); return 1; } close (fd); fd = syscall (__NR_dup3, 1, 4, O_CLOEXEC); if (fd == -1) { puts ("dup3(O_CLOEXEC) failed"); return 1; } coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if ((coe & FD_CLOEXEC) == 0) { puts ("dup3(O_CLOEXEC) set close-on-exec flag"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Ulrich Drepper authored
This patch adds the new epoll_create2 syscall. It extends the old epoll_create syscall by one parameter which is meant to hold a flag value. In this patch the only flag support is EPOLL_CLOEXEC which causes the close-on-exec flag for the returned file descriptor to be set. A new name EPOLL_CLOEXEC is introduced which in this implementation must have the same value as O_CLOEXEC. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <time.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_epoll_create2 # ifdef __x86_64__ # define __NR_epoll_create2 291 # elif defined __i386__ # define __NR_epoll_create2 329 # else # error "need __NR_epoll_create2" # endif #endif #define EPOLL_CLOEXEC O_CLOEXEC int main (void) { int fd = syscall (__NR_epoll_create2, 1, 0); if (fd == -1) { puts ("epoll_create2(0) failed"); return 1; } int coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if (coe & FD_CLOEXEC) { puts ("epoll_create2(0) set close-on-exec flag"); return 1; } close (fd); fd = syscall (__NR_epoll_create2, 1, EPOLL_CLOEXEC); if (fd == -1) { puts ("epoll_create2(EPOLL_CLOEXEC) failed"); return 1; } coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if ((coe & FD_CLOEXEC) == 0) { puts ("epoll_create2(EPOLL_CLOEXEC) set close-on-exec flag"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Ulrich Drepper authored
The timerfd_create syscall already has a flags parameter. It just is unused so far. This patch changes this by introducing the TFD_CLOEXEC flag to set the close-on-exec flag for the returned file descriptor. A new name TFD_CLOEXEC is introduced which in this implementation must have the same value as O_CLOEXEC. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <time.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_timerfd_create # ifdef __x86_64__ # define __NR_timerfd_create 283 # elif defined __i386__ # define __NR_timerfd_create 322 # else # error "need __NR_timerfd_create" # endif #endif #define TFD_CLOEXEC O_CLOEXEC int main (void) { int fd = syscall (__NR_timerfd_create, CLOCK_REALTIME, 0); if (fd == -1) { puts ("timerfd_create(0) failed"); return 1; } int coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if (coe & FD_CLOEXEC) { puts ("timerfd_create(0) set close-on-exec flag"); return 1; } close (fd); fd = syscall (__NR_timerfd_create, CLOCK_REALTIME, TFD_CLOEXEC); if (fd == -1) { puts ("timerfd_create(TFD_CLOEXEC) failed"); return 1; } coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if ((coe & FD_CLOEXEC) == 0) { puts ("timerfd_create(TFD_CLOEXEC) set close-on-exec flag"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Ulrich Drepper authored
This patch adds the new eventfd2 syscall. It extends the old eventfd syscall by one parameter which is meant to hold a flag value. In this patch the only flag support is EFD_CLOEXEC which causes the close-on-exec flag for the returned file descriptor to be set. A new name EFD_CLOEXEC is introduced which in this implementation must have the same value as O_CLOEXEC. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_eventfd2 # ifdef __x86_64__ # define __NR_eventfd2 290 # elif defined __i386__ # define __NR_eventfd2 328 # else # error "need __NR_eventfd2" # endif #endif #define EFD_CLOEXEC O_CLOEXEC int main (void) { int fd = syscall (__NR_eventfd2, 1, 0); if (fd == -1) { puts ("eventfd2(0) failed"); return 1; } int coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if (coe & FD_CLOEXEC) { puts ("eventfd2(0) sets close-on-exec flag"); return 1; } close (fd); fd = syscall (__NR_eventfd2, 1, EFD_CLOEXEC); if (fd == -1) { puts ("eventfd2(EFD_CLOEXEC) failed"); return 1; } coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if ((coe & FD_CLOEXEC) == 0) { puts ("eventfd2(EFD_CLOEXEC) does not set close-on-exec flag"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [akpm@linux-foundation.org: add sys_ni stub] Signed-off-by: -
Ulrich Drepper authored
This patch adds the new signalfd4 syscall. It extends the old signalfd syscall by one parameter which is meant to hold a flag value. In this patch the only flag support is SFD_CLOEXEC which causes the close-on-exec flag for the returned file descriptor to be set. A new name SFD_CLOEXEC is introduced which in this implementation must have the same value as O_CLOEXEC. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <signal.h> #include <stdio.h> #include <unistd.h> #include <sys/syscall.h> #ifndef __NR_signalfd4 # ifdef __x86_64__ # define __NR_signalfd4 289 # elif defined __i386__ # define __NR_signalfd4 327 # else # error "need __NR_signalfd4" # endif #endif #define SFD_CLOEXEC O_CLOEXEC int main (void) { sigset_t ss; sigemptyset (&ss); sigaddset (&ss, SIGUSR1); int fd = syscall (__NR_signalfd4, -1, &ss, 8, 0); if (fd == -1) { puts ("signalfd4(0) failed"); return 1; } int coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if (coe & FD_CLOEXEC) { puts ("signalfd4(0) set close-on-exec flag"); return 1; } close (fd); fd = syscall (__NR_signalfd4, -1, &ss, 8, SFD_CLOEXEC); if (fd == -1) { puts ("signalfd4(SFD_CLOEXEC) failed"); return 1; } coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if ((coe & FD_CLOEXEC) == 0) { puts ("signalfd4(SFD_CLOEXEC) does not set close-on-exec flag"); return 1; } close (fd); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [akpm@linux-foundation.org: add sys_ni stub] Signed-off-by: -
Ulrich Drepper authored
This patch just extends the anon_inode_getfd interface to take an additional parameter with a flag value. The flag value is passed on to get_unused_fd_flags in anticipation for a use with the O_CLOEXEC flag. No actual semantic changes here, the changed callers all pass 0 for now. [akpm@linux-foundation.org: KVM fix] Signed-off-by:
-
Ulrich Drepper authored
Some platforms do not have support to restore the signal mask in the return path from a syscall. For those platforms syscalls like pselect are not defined at all. This is, I think, not a good choice for paccept() since paccept() adds more value on top of accept() than just the signal mask handling. Therefore this patch defines a scaled down version of the sys_paccept function for those platforms. It returns -EINVAL in case the signal mask is non-NULL but behaves the same otherwise. Note that I explicitly included <linux/thread_info.h>. I saw that it is currently included but indirectly two levels down. There is too much risk in relying on this. The header might change and then suddenly the function definition would change without anyone immediately noticing. Signed-off-by:
-
Ulrich Drepper authored
This patch is by far the most complex in the series. It adds a new syscall paccept. This syscall differs from accept in that it adds (at the userlevel) two additional parameters: - a signal mask - a flags value The flags parameter can be used to set flag like SOCK_CLOEXEC. This is imlpemented here as well. Some people argued that this is a property which should be inherited from the file desriptor for the server but this is against POSIX. Additionally, we really want the signal mask parameter as well (similar to pselect, ppoll, etc). So an interface change in inevitable. The flag value is the same as for socket and socketpair. I think diverging here will only create confusion. Similar to the filesystem interfaces where the use of the O_* constants differs, it is acceptable here. The signal mask is handled as for pselect etc. The mask is temporarily installed for the thread and removed before the call returns. I modeled the code after pselect. If there is a problem it's likely also in pselect. For architectures which use socketcall I maintained this interface instead of adding a system call. The symmetry shouldn't be broken. The following test must be adjusted for architectures other than x86 and x86-64 and in case the syscall numbers changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <errno.h> #include <fcntl.h> #include <pthread.h> #include <signal.h> #include <stdio.h> #include <unistd.h> #include <netinet/in.h> #include <sys/socket.h> #include <sys/syscall.h> #ifndef __NR_paccept # ifdef __x86_64__ # define __NR_paccept 288 # elif defined __i386__ # define SYS_PACCEPT 18 # define USE_SOCKETCALL 1 # else # error "need __NR_paccept" # endif #endif #ifdef USE_SOCKETCALL # define paccept(fd, addr, addrlen, mask, flags) \ ({ long args[6] = { \ (long) fd, (long) addr, (long) addrlen, (long) mask, 8, (long) flags }; \ syscall (__NR_socketcall, SYS_PACCEPT, args); }) #else # define paccept(fd, addr, addrlen, mask, flags) \ syscall (__NR_paccept, fd, addr, addrlen, mask, 8, flags) #endif #define PORT 57392 #define SOCK_CLOEXEC O_CLOEXEC static pthread_barrier_t b; static void * tf (void *arg) { pthread_barrier_wait (&b); int s = socket (AF_INET, SOCK_STREAM, 0); struct sockaddr_in sin; sin.sin_family = AF_INET; sin.sin_addr.s_addr = htonl (INADDR_LOOPBACK); sin.sin_port = htons (PORT); connect (s, (const struct sockaddr *) &sin, sizeof (sin)); close (s); pthread_barrier_wait (&b); s = socket (AF_INET, SOCK_STREAM, 0); sin.sin_port = htons (PORT); connect (s, (const struct sockaddr *) &sin, sizeof (sin)); close (s); pthread_barrier_wait (&b); pthread_barrier_wait (&b); sleep (2); pthread_kill ((pthread_t) arg, SIGUSR1); return NULL; } static void handler (int s) { } int main (void) { pthread_barrier_init (&b, NULL, 2); struct sockaddr_in sin; pthread_t th; if (pthread_create (&th, NULL, tf, (void *) pthread_self ()) != 0) { puts ("pthread_create failed"); return 1; } int s = socket (AF_INET, SOCK_STREAM, 0); int reuse = 1; setsockopt (s, SOL_SOCKET, SO_REUSEADDR, &reuse, sizeof (reuse)); sin.sin_family = AF_INET; sin.sin_addr.s_addr = htonl (INADDR_LOOPBACK); sin.sin_port = htons (PORT); bind (s, (struct sockaddr *) &sin, sizeof (sin)); listen (s, SOMAXCONN); pthread_barrier_wait (&b); int s2 = paccept (s, NULL, 0, NULL, 0); if (s2 < 0) { puts ("paccept(0) failed"); return 1; } int coe = fcntl (s2, F_GETFD); if (coe & FD_CLOEXEC) { puts ("paccept(0) set close-on-exec-flag"); return 1; } close (s2); pthread_barrier_wait (&b); s2 = paccept (s, NULL, 0, NULL, SOCK_CLOEXEC); if (s2 < 0) { puts ("paccept(SOCK_CLOEXEC) failed"); return 1; } coe = fcntl (s2, F_GETFD); if ((coe & FD_CLOEXEC) == 0) { puts ("paccept(SOCK_CLOEXEC) does not set close-on-exec flag"); return 1; } close (s2); pthread_barrier_wait (&b); struct sigaction sa; sa.sa_handler = handler; sa.sa_flags = 0; sigemptyset (&sa.sa_mask); sigaction (SIGUSR1, &sa, NULL); sigset_t ss; pthread_sigmask (SIG_SETMASK, NULL, &ss); sigaddset (&ss, SIGUSR1); pthread_sigmask (SIG_SETMASK, &ss, NULL); sigdelset (&ss, SIGUSR1); alarm (4); pthread_barrier_wait (&b); errno = 0 ; s2 = paccept (s, NULL, 0, &ss, 0); if (s2 != -1 || errno != EINTR) { puts ("paccept did not fail with EINTR"); return 1; } close (s); puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ [akpm@linux-foundation.org: make it compile] [akpm@linux-foundation.org: add sys_ni stub] Signed-off-by: -
Ulrich Drepper authored
This patch adds support for flag values which are ORed to the type passwd to socket and socketpair. The additional code is minimal. The flag values in this implementation can and must match the O_* flags. This avoids overhead in the conversion. The internal functions sock_alloc_fd and sock_map_fd get a new parameters and all callers are changed. ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ #include <fcntl.h> #include <stdio.h> #include <unistd.h> #include <netinet/in.h> #include <sys/socket.h> #define PORT 57392 /* For Linux these must be the same. */ #define SOCK_CLOEXEC O_CLOEXEC int main (void) { int fd; fd = socket (PF_INET, SOCK_STREAM, 0); if (fd == -1) { puts ("socket(0) failed"); return 1; } int coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if (coe & FD_CLOEXEC) { puts ("socket(0) set close-on-exec flag"); return 1; } close (fd); fd = socket (PF_INET, SOCK_STREAM|SOCK_CLOEXEC, 0); if (fd == -1) { puts ("socket(SOCK_CLOEXEC) failed"); return 1; } coe = fcntl (fd, F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if ((coe & FD_CLOEXEC) == 0) { puts ("socket(SOCK_CLOEXEC) does not set close-on-exec flag"); return 1; } close (fd); int fds[2]; if (socketpair (PF_UNIX, SOCK_STREAM, 0, fds) == -1) { puts ("socketpair(0) failed"); return 1; } for (int i = 0; i < 2; ++i) { coe = fcntl (fds[i], F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if (coe & FD_CLOEXEC) { printf ("socketpair(0) set close-on-exec flag for fds[%d]\n", i); return 1; } close (fds[i]); } if (socketpair (PF_UNIX, SOCK_STREAM|SOCK_CLOEXEC, 0, fds) == -1) { puts ("socketpair(SOCK_CLOEXEC) failed"); return 1; } for (int i = 0; i < 2; ++i) { coe = fcntl (fds[i], F_GETFD); if (coe == -1) { puts ("fcntl failed"); return 1; } if ((coe & FD_CLOEXEC) == 0) { printf ("socketpair(SOCK_CLOEXEC) does not set close-on-exec flag for fds[%d]\n", i); return 1; } close (fds[i]); } puts ("OK"); return 0; } ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: -
Akinobu Mita authored
Signed-off-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Adrian Bunk authored
The driver is gone for a long time. Reported-by:
Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by:
-
Adrian Bunk authored
SOUND_TRIDENT was the last PCI OSS driver, and since there's already an ALSA driver for the same hardware we can remove it. [muli@il.ibm.com: update CREDITS] Signed-off-by:
Muli Ben-Yehuda <muli@il.ibm.com> Signed-off-by:
-
Andy Whitcroft authored
Signed-off-by:
Andy Whitcroft <apw@shadowen.org> Signed-off-by:
-
Andy Whitcroft authored
When checking spacing for pointer checks the type cannot start in the middle of a word, ie. this is not 'int * bar': x = fooint * bar; Signed-off-by:
-
Andy Whitcroft authored
Ensure we ignore comments in complex macro detection else we incorrectly report this: #define PFM_GROUP_PERM_ANY -1 /* any user/group */ Signed-off-by:
-
Andy Whitcroft authored
Now that we have a variants system, move to using that to carry the unary/binary designation for +, -, &, and *. Signed-off-by:
-
Andy Whitcroft authored
Add checks for the question mark colon operator spacing, and also check the other uses of colon. Colon means a number of things: - it introduces the else part of the ?: operator, - it terminates a goto label, - it terminates the case value, - it separates the identifier from the bit size on bit fields, and - it is used to introduce option types in asm(). Signed-off-by:
-
Andy Whitcroft authored
Add support for multiple modifiers such as: int __one __two foo; Also handle trailing known modifiers when defecting modifiers: int __one foo __read_mostly; Signed-off-by:
-
Andy Whitcroft authored
Ensure we do not inadvertantly load known modifiers up as possible types. Signed-off-by:
-
Andy Whitcroft authored
Make sure we correctly mark the return type of the pointer to a function declaration. const void *(*sb_tag)(struct sysfs_tag_info *info); Signed-off-by: -
Andy Whitcroft authored
Exclude vmlinux.lds.h from the macro complexity checks. They will never apply sanely here. Signed-off-by:
-
Andy Whitcroft authored
Although we are finding the added modifier in the declaration below we are not correctly matching it as a type. Fix the declaration. static void __ref *vmem_alloc_pages(unsigned int order) { } Signed-off-by: -
Andy Whitcroft authored
Improve type matcher debug so we can see what it does match. As part of this move us to to using the common debug framework. Signed-off-by:
-
Andy Whitcroft authored
Allow for type modifiers mid declaration on multiple declarations: struct mxser_mstatus ms, __user *msu = argp; Reported by Jiri Slaby. Signed-off-by:
-
