IPv6 GRO over GRE tap is not working while GRO is not set
over the native interface.

gro_list_prepare function updates the same_flow variable
of existing sessions to 1 if their mac headers match the one
of the incoming packet.
same_flow is used to filter out non-matching sessions and keep
potential ones for aggregation.

The number of bytes to compare should be the number of bytes
in the mac headers. In gro_list_prepare this number is set to
be skb->dev->hard_header_len. For GRE interfaces this hard_header_len
should be as it is set in the initialization process (when GRE is
created), it should not be overridden. But currently it is being overridden
by the value that is actually supposed to represent the needed_headroom.
Therefore, the number of bytes compared in order to decide whether the
the mac headers are the same is greater than the length of the headers.

As it's documented in netdevice.h, hard_header_len is the maximum
hardware header length, and needed_headroom is the extra headroom
the hardware may need.
hard_header_len is basically all the bytes received by the physical
till layer 3 header of the packet received by the interface.
For example, if the interface is a GRE tap then the needed_headroom
should be the total length of the following headers:
IP header of the physical, GRE header, mac header of GRE.
It is often used to calculate the MTU of the created interface.

This patch removes the override of the hard_header_len, and
assigns the calculated value to needed_headroom.
This way, the comparison in gro_list_prepare is really of
the mac headers, and if the packets have the same mac headers
the same_flow will be set to 1.

Performance testing: 45% higher bandwidth.
Measuring bandwidth of single-stream IPv4 TCP traffic over IPv6
GRE tap while GRO is not set on the native.
NIC: ConnectX-4LX
Before (GRO not working) : 7.2 Gbits/sec
After (GRO working): 10.5 Gbits/sec
Signed-off-by: Maria Pasechnik <mariap@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Manish Chopra says:

====================
qed*: Enhancements

This patch series adds following support in drivers -

1. Egress mqprio offload.
2. Add destination IP based flow profile.
3. Ingress flower offload (for drop action).

Please consider applying this series to "net-next".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The main motive of this patch is to lay down driver's
tc offload infrastructure in place.

With these changes tc can offload various supported flow
profiles (4 tuples, src-ip, dst-ip, l4 port) for the drop
action. Dropped flows statistic is a global counter for
all the offloaded flows for drop action and is populated
in ethtool statistics as common "gft_filter_drop".

Examples -

tc qdisc add dev p4p1 ingress
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
	skip_sw ip_proto tcp dst_ip 192.168.40.200 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
	skip_sw ip_proto udp src_ip 192.168.40.100 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
	skip_sw ip_proto tcp src_ip 192.168.40.100 dst_ip 192.168.40.200 \
	src_port 453 dst_port 876 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
	skip_sw ip_proto tcp dst_port 98 action drop
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for dropping and redirecting
the flows based on destination IP in the packet.

This also moves the profile mode settings in their own
functions which can be used through tc flows in successive
patch.

For example -

ethtool -N p5p1 flow-type tcp4 dst-ip 192.168.40.100 action -1
ethtool -N p5p1 flow-type udp4 dst-ip 192.168.50.100 action 1
ethtool -N p5p1 flow-type tcp4 dst-ip 192.168.60.100 action 0x100000000
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for tc mqprio offload,
using this different traffic classes on the adapter
can be utilized based on configured priority to tc map.

For example -

tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3

This will cause SKBs with priority 0,1,2,3 to transmit
over tc 0,1,2,3 hardware queues respectively.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Wiedmann says:

====================
s390/qeth: updates 2018-08-09

one more set of patches for net-next. This is all sorts of cleanups and
more refactoring on the way to using netdev_priv. Please apply.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Return statements in functions returning bool should use true or false
instead of an integer value.

This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allocating the main qeth_card struct with GFP_DMA blocks us from moving
it into netdev_priv(). But the only reason why we need DMA memory is the
ccw1 structs embedded into each ccw channel. So extract those into
separate allocations, like we already do for the cmd buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The qeth_card struct is kzalloc-ed, so remove all the redundant
0-initializations. While at it, split up what's left of
qeth_determine_card_type().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The data channel currently doesn't need a setup operation, because we
don't use pre-allocated cmd buffers for its IO. But subsequent changes
will introduce further setup that also applies to the data channel.
This refactors things a bit, so that the new stuff can then be
automatically applied to all channels.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Re-work the helper a little bit, so that it can be used for all CCWs
that qeth issues.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Where possible use accessor macros and local pointers to access the ccw
channels. This makes it less likely to miss a spot.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Just a little code deduplication.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Overlapping changes in RXRPC, changing to ktime_get_seconds() whilst
adding some tracepoints.
Signed-off-by: David S. Miller <davem@davemloft.net>

Jose Abreu says:

====================
Add support for XGMAC2 in stmmac

This series adds support for 10Gigabit IP in stmmac. The IP is called XGMAC2
and has many similarities with GMAC4. Due to this, its relatively easy to
incorporate this new IP into stmmac driver by adding a new block and
filling the necessary callbacks.

The functionality added by this series is still reduced but its only a
starting point which will later be expanded.

I splitted the patches into funcionality and to ease the review. Only the
patch 8/9 really enables the XGMAC2 block by adding a new compatible string.

Version 4 addresses review comments of Florian Fainelli and Rob Herring.

NOTE: Although the IP supports 10G, for now it was only possible to test it
at 1G speed due to 10G PHY HW shipping problems. Here follows iperf3
results at 1G:

Connecting to host 192.168.0.10, port 5201
[  4] local 192.168.0.3 port 39178 connected to 192.168.0.10 port 5201
[ ID] Interval           Transfer     Bandwidth       Retr  Cwnd
[  4]   0.00-1.00   sec   110 MBytes   920 Mbits/sec    0    482 KBytes
[  4]   1.00-2.00   sec   113 MBytes   946 Mbits/sec    0    482 KBytes
[  4]   2.00-3.00   sec   112 MBytes   937 Mbits/sec    0    482 KBytes
[  4]   3.00-4.00   sec   113 MBytes   946 Mbits/sec    0    482 KBytes
[  4]   4.00-5.00   sec   112 MBytes   935 Mbits/sec    0    482 KBytes
[  4]   5.00-6.00   sec   113 MBytes   946 Mbits/sec    0    482 KBytes
[  4]   6.00-7.00   sec   112 MBytes   937 Mbits/sec    0    482 KBytes
[  4]   7.00-8.00   sec   113 MBytes   946 Mbits/sec    0    482 KBytes
[  4]   8.00-9.00   sec   112 MBytes   937 Mbits/sec    0    482 KBytes
[  4]   9.00-10.00  sec   113 MBytes   946 Mbits/sec    0    482 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bandwidth       Retr
[  4]   0.00-10.00  sec  1.09 GBytes   940 Mbits/sec    0             sender
[  4]   0.00-10.00  sec  1.09 GBytes   938 Mbits/sec                  receiver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds the documentation for XGMAC2 DT bindings.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the bindings parsing for XGMAC2 IP block.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we have all the XGMAC related callbacks, lets start integrating
this IP block into main driver.

Also, we corrected the initialization flow to only start DMA after
setting descriptors length.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

XGMAC2 uses the same engine of timestamping as GMAC4. Let's use the same
callbacks.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the MDIO related funcionalities for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the descriptor related callbacks for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the DMA related callbacks for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the MAC related callbacks for the new IP block XGMAC2.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new entry to HWIF table for XGMAC 2.10. For now we fill it with
empty callbacks which will be added in posterior patches.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
More complete PHYLINK support for mv88e6xxx

Previous patches added sufficient PHYLINK support to the mv88e6xxx
that it did not break existing use cases, basically fixed-link phys.

This patchset builds out the support so that SFP modules, up to
2.5Gbps can be supported, on mv88e6390X, on ports 9 and 10. It also
provides a framework which can be extended to support SFPs on ports
2-8 of mv88e6390X, 10Gbps PHYs, and SFP support on the 6352 family.

Russell King did much of the initial work, implementing the validate
and mac_link_state calls. However, there is an important TODO in the
commit message:

needs to call phylink_mac_change() when the port link comes up/goes down.

The remaining patches implement this, by adding more support for the
SERDES interfaces, in particular, interrupt support so we get notified
when the SERDES gains/looses sync.

This has been tested on the ZII devel C, using a Clearfog as peer
device.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When a port changes CMODE, the SERDES interface being used can change.
Disable interrupts for the old SERDES interface, and enable interrupts
on the new.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

phylink wants to know when the MAC layers notices a change in the
link. For the 6390 family, this is a change in the SERDES state.

Add interrupt support for the SERDES interface used to implement
SGMII/1000Base-X/2500Base-X. This is currently limited to ports 9 and
10. Support for the 10G SERDES and other ports will be added later,
building on this basic framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

An up coming change will register interrupts for individual switch
ports, using the mv88e6xxx_port as the interrupt context information.
Add members to the mv88e6xxx_port structure so we can link it back to
the mv88e6xxx_chip member the port belongs to and the port number of
the port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 6390 family has a number of SERDES interfaces per port. When the
cmode changes, eg 1000Base-X to XAUI, the SERDES interface in use will
also change. Power down the old SERDES interface and power up the new
SERDES interface.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ports CMODE indicates the type of link between the MAC and the
PHY. It is used often in the SERDES code. Rather than read it each
time, cache its value.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 6390 has three different SERDES interface types. 2500Base-X is
implemented by the SGMII/1000Base-X SERDES. So power on/off the
correct SERDES.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a helper for accessing SERDES registers of the 6390 family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a need to add more functions manipulating the SERDES
interfaces. Cleanup the namespace.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 6390 has two SERDES interfaces, used by ports 9 and 10.  The 6390X
has eight SERDES interfaces. These allow ports 9 and 10 to do 10G. Or
if lower speeds are used, some of the SERDES interfaces can be used by
ports 2-8 for 1000Base-X.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 6390 family has 8 SERDES lanes. What ports use these lanes depends
on how ports 9 and 10 are configured. If 9 and 10 does not make use of
a line, one of the lower ports can use it.

Add a function to return the lane a port is using, if any, and simplify
the code to power up/down the lane.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add rudimentary phylink support to mv88e6xxx.

TODO:
- needs to call phylink_mac_change() when the port link comes up/goes down.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a helper for MAC drivers to use in their validate callback to deal
with 2500BaseX vs 1000BaseX modes, where the hardware supports both
but it is not possible to automatically select between them.

This helper defaults to 1000BaseX, as that is the 802.3 standard, and
will allow users to select 2500BaseX either by forcing the speed if
AN is disabled, or by changing the advertising mask if AN is enabled.
Disabling AN is not recommended as it is only the speed that we're
interested in controlling, not the duplex or pause mode parameters.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 6185 can enable/disable 802.3z pause be setting the MyPause bit in
the port status register. Add an op to support this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Various updates

Patches 1-3 update the driver to use a new firmware version. Due to a
recently discovered issue, the version (and future ones) does not
support matching on VLAN ID at egress. This is enforced in the driver
and reported back to the user via extack.

Patch 4 adds a new selftest for the recently introduced algorithmic
TCAM.

Patch 5 converts the driver to use SPDX identifiers.

Patches 6-7 fix a bug in ethtool stats reporting and expose counters for
all 16 TCs, following recent MC-aware changes that utilize TCs 8-15.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Before MC-aware mode was enabled in commit 7b819530 ("mlxsw:
spectrum: Configure MC-aware mode on mlxsw ports"), only 8 traffic
classes were used. Under MC-aware regime, however, besides using TCs
0-7 for UC traffic, it additionally uses TCs 8-15 for BUM traffic. It
is therefore desirable to show counters for these TCs as well.

Update ethtool stats pool length, mlxsw_sp_port_get_strings() and
mlxsw_sp_port_get_stats() to include artifacts for all 16 TCs. For
consistency and simplicity, expose tc_no_buffer_discard_uc_tc for BUM
TCs as well, even though it ought to stay at 0 all the time.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>