Skip to content

L
linux
Switch branch/tag
  1. 15 Jan, 2012 3 commits
  3. 25 Dec, 2011 1 commit
  5. 18 Oct, 2011 2 commits
    • Clemens Ladisch's avatar
      firewire: ohci: fix isochronous DMA synchronization · a572e688
      Clemens Ladisch authored 
      Add the dma_sync_single_* calls necessary to ensure proper cache
synchronization for isochronous data buffers on non-coherent
architectures.
Signed-off-by: default avatarClemens Ladisch <clemens@ladisch.de>
Signed-off-by: default avatarStefan Richter <stefanr@s5r6.in-berlin.de>
      a572e688
    • Clemens Ladisch's avatar
      firewire: ohci: work around selfID junk due to wrong gap count · 32eaeae1
      Clemens Ladisch authored 
      If a device's firmware initiates a bus reset by setting the IBR bit in
PHY register 1 without resetting the gap count field to 63 (and without
having sent a PHY configuration packet beforehand), the gap count of
this node will remain at the old value after the bus reset and thus be
inconsistent with the gap count on all other nodes.

The bus manager is supposed to detect the inconsistent gap count values
in the self ID packets and correct them by issuing another bus reset.

However, if the buggy device happens to be the cycle master, and if it
sends a cycle start packet immediately after the bus reset (which is
likely after a long bus reset), then the time between the end of the
selfID phase and the start of the cycle start packet will be based on
the too-small gap count value, so this gap will be too short to be
detected as a subaction gap by the other nodes.  This means that the
cycle start packet will be assumed to be self ID data, and will be
stored after the actual self ID quadlets in the self ID buffer.

This garbage in the self ID buffer made firewire-core ignore all of the
self ID data, and thus prevented the Linux bus manager from correcting
the problem.  Furthermore, because the bus reset handling was aborted
completely, asynchronous transfers would be no longer handled correctly,
and fw_run_transaction() would hang until the next bus reset.

To fix this, make the detection of inconsistent self IDs more
discriminating:  If the invalid data in the self ID buffer looks like
a cycle start packet, we can assume that the previous data in the buffer
is correctly received self ID information, and process it normally.

(We inspect only the first quadlet of the cycle start packet, because
this value is different enough from any valid self ID quadlet, and many
controllers do not store the cycle start packet in five quadlets because
they expect self ID data to have an even number of quadlets.)

This bug has been observed when a bus-powered DesktopKonnekt6 is
switched off with its power button.
Signed-off-by: default avatarClemens Ladisch <clemens@ladisch.de>
Signed-off-by: default avatarStefan Richter <stefanr@s5r6.in-berlin.de>
      32eaeae1
  7. 09 Oct, 2011 4 commits
  9. 16 Sep, 2011 6 commits
    • Stephan Gatzka's avatar
      firewire: ohci: Add support for TSB41BA3D phy · 25935ebe
      Stephan Gatzka authored 
      This patch implements a work around for the Texas Instruments PHY
TSB41BA3D.  This phy has a bug at least in combination with the TI LLCs
TSB82AA2B and TSB12LV26.  The selfid coming from the locally connected
phy is not propagated into the selfid buffer of the OHCI (see
http://www.ti.com/litv/pdf/sllz059 for details).  The main idea is to
construct the selfid ourselves.
Signed-off-by: default avatarStephan Gatzka <stephan@gatzka.org>
Signed-off-by: default avatarStefan Richter <stefanr@s5r6.in-berlin.de>
      25935ebe
    • Stephan Gatzka's avatar
      firewire: ohci: Move code from the bus reset tasklet into a workqueue · 2d7a36e2
      Stephan Gatzka authored 
      Code inside bus_reset_work may now sleep. This is a prerequisite to
support a phy from Texas Instruments cleanly. The patch to support this
phy will be submitted later.
Signed-off-by: default avatarStephan Gatzka <stephan@gatzka.org>
Signed-off-by: default avatarStefan Richter <stefanr@s5r6.in-berlin.de>
      2d7a36e2
    • Stefan Richter's avatar
      firewire: sbp2: fold two functions into one · 32ce38f4
      Stefan Richter authored 
      sbp2_release_target() is folded into its primary user, sbp2_remove().
The only other caller, a failure path in sbp2_probe(), now uses
sbp2_remove().  This adds unnecessary cancel_delayed_work_sync() calls
to that failure path but results in less code and text.
Signed-off-by: default avatarStefan Richter <stefanr@s5r6.in-berlin.de>
      32ce38f4
    • Stefan Richter's avatar
      firewire: sbp2: move some code to more sensible places · b2af07b6
      Stefan Richter authored 
      Implement sbp2_queue_work(), which is now a very simple accessor to one
of the struct sbp2_logical_unit members, right after the definition of
struct sbp2_logical_unit.

Put the sbp2_reconnect() implementation right after the sbp2_login()
implementation.  They are both part of the SBP-2 access protocol.

Implement the driver methods sbp2_probe(), spp2_update(), sbp2_remove()
in this order, reflecting the lifetime of an SBP-2 target.

Place the sbp2_release_target() implementation right next to
sbp2_remove() which is its primary user, and after sbp2_probe() which is
the counterpart to sbp2_release_target().

There are no changes to the implementations here, or at least not meant
to be.
Signed-off-by: default avatarStefan Richter <stefanr@s5r6.in-berlin.de>
      b2af07b6
    • Stefan Richter's avatar
      firewire: sbp2: remove obsolete reference counting · 6ff8147d
      Stefan Richter authored 
      Since commit 0278ccd9 "firewire: sbp2:
fix panic after rmmod with slow targets", the lifetime of an sbp2_target
instance does no longer extent past the return of sbp2_remove().
Therefore it is no longer necessary to call fw_unit_get/put() and
fw_device_get/put() in sbp2_probe/remove().

Furthermore, said commit also ensures that lu->work is not going to be
executed or requeued at a time when the sbp2_target is no longer in use.
Hence there is no need for sbp2_target reference counting for lu->work.

Other concurrent contexts:

  - Processes which access the sysfs of the SCSI host device or of one
    of its subdevices are safe because these interfaces are all removed
    by scsi_remove_device/host() in sbp2_release_target().

  - SBP-2 command block ORB transactions are finished when
    scsi_remove_device() in sbp2_release_target() returns.

  - SBP-2 management ORB transactions are finished when
    cancel_delayed_work_sync(&lu->work) before sbp2_release_target()
    returns.
Signed-off-by: default avatarStefan Richter <stefanr@s5r6.in-berlin.de>
      6ff8147d
    • Ming Lei's avatar
      firewire: ohci: add no MSI quirk for O2Micro controller · f39aa30d
      Ming Lei authored 
      This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801719 .

An O2Micro PCI Express FireWire controller,
"FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Device [1217:11f7] (rev 05)"
which is a combination device together with an SDHCI controller and some
sort of storage controller, misses SBP-2 status writes from an attached
FireWire HDD.  This problem goes away if MSI is disabled for this
FireWire controller.

The device reportedly does not require QUIRK_CYCLE_TIMER.
Signed-off-by: default avatarMing Lei <ming.lei@canonical.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (amended changelog)
Cc: <stable@kernel.org>
      f39aa30d
  11. 12 Sep, 2011 9 commits
  13. 11 Sep, 2011 15 commits
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7